Search

The optical constants of single-crystal AlxGa1−xP and AlxGa1−xAs have been widely studied at various Al compositions but have not yet been thoroughly investigated as polycrystalline materials. Using variable-angle spectroscopic ellipsometry, we estimate and analyze the optical constants of polycrystalline Al0.25Ga0.75P and Al0.9Ga0.1As that were non-epitaxially deposited at deposition temperatures of either 250 or 420 °C, and with various dopant species, dopant concentrations, and V/III flux ratios. For wavelengths of 350–400 nm, decreasing the V/III ratio increases the refractive index of Be-doped polycrystalline Al0.25Ga0.75P. For wavelengths >500 nm, as the targeted Be dopant concentration increases for polycrystalline Al0.25Ga0.75P, the amount the extinction coefficient increases and the indirect bandgap decreases depends on the V/III ratio. Furthermore, Si-doped polycrystalline Al0.25Ga0.75P has significantly smaller extinction coefficient values than when it is Be-doped, for the same V/III ratio and targeted doping concentration, at wavelengths >500 nm. Based on our findings, we hypothesize that the dopant species, dopant concentration, and the V/III ratio dictate various types of defect concentrations, which then affect the optical constants and indirect bandgap of polycrystalline Al0.25Ga0.75P. Additionally, for wavelengths >500 nm, we find that polycrystalline Al0.25Ga0.75P and Al0.9Ga0.1As have the lowest extinction coefficient values when deposited at 420 °C, as opposed to 250 °C. Thus, we hypothesize that the deposition temperature is the most significant factor in dictating the optical constants of these polycrystalline III-Vs. Ultimately, this work demonstrates alternative methods to tune the optical constants of polycrystalline Al0.25Ga0.75P and Al0.9Ga0.1As, as opposed to tuning the Al composition. [ABSTRACT FROM AUTHOR]

A graded buffer Bragg reflector (GBBR) is a bifunctional device component that provides the reflection of a distributed Bragg reflector and the adjustable lattice constant of a compositionally graded buffer. Prior work showed that these properties can be combined with low threading dislocation density and high reflectivity. Here, we design and demonstrate complex GBBRs for specific metamorphic solar cell applications. We design buffers that provide (1) high reflectivity over a narrow bandwidth, for quantum well solar cells, (2) reflectivity over a wide bandwidth, for optically thin solar cells, and (3) low sidelobe reflection, for multijunction devices that demand low out-of-band reflection. Apodized and triple GBBRs are demonstrated, and transparency is always considered, requiring designs with carefully engineered material combinations. A GBBR with a reflection of 99% is demonstrated, as well as a triple GBBR that has over 80% reflection for 100 nm of the spectrum around 800 nm. We also analyze potential deviations in a baseline GBBR from that of a perfect DBR using transmission electron microscopy to analyze imperfections in the material and modeling to analyze the impact of imperfect refractive index data for lattice-mismatched AlGaInAs. Minimal crosshatch roughness and unintentional thickness variation occur throughout the buffer, which likely influences reflection slightly. Small deviations between the calculated AlGaInAs and utilized AlGaAs refractive index exist, giving methods for future GBBR improvement. While the GBBR designs are intended for metamorphic solar cells, the broad and high reflection may also be useful for other optoelectronic devices such as light-emitting diodes or lasers. [ABSTRACT FROM AUTHOR]

This study presents the growth and characterization of an 8.1 μm-emitting, InGaAs/AlInAs/InP-based quantum cascade laser (QCL) formed on an InP-on-Si composite template by metalorganic chemical vapor deposition (MOCVD). First, for the composite-template formation, a GaAs buffer layer was grown by solid-source molecular-beam epitaxy on a commercial (001) GaP/Si substrate, thus forming a GaAs/GaP/Si template. Next, an InP metamorphic buffer layer (MBL) structure was grown atop the GaAs/GaP/Si template by MOCVD, followed by the MOCVD growth of the full QCL structure. The top-surface morphology of the GaAs/GaP/Si template before and after the InP MBL growth was assessed via atomic force microscopy, over a 100 μm2 area, and no antiphase domains were found. The average threading dislocation density (TDD) for the GaAs/GaP/Si template was found to be ∼1 × 109 cm−2, with a slightly lower defect density of ∼7.9 × 108 cm−2 after the InP MBL growth. The lasing performance of the QCL structure grown on Si was compared to that of its counterpart grown on InP native substrate and found to be quite similar. That is, the threshold-current density of the QCL on Si, for deep-etched ridge-guide devices with uncoated facets, is somewhat lower than that for its counterpart on native InP substrate, 1.50 vs 1.92 kA/cm2, while the maximum output power per facet is 1.64 vs 1.47 W. These results further demonstrate the resilience of QCLs to relatively high residual TDD values. [ABSTRACT FROM AUTHOR]

This study investigated how Hong Kong's community centers for older people faced challenges and delivered services amid the Covid-19 pandemic. According to experiences of 110 health and social care workers who completed an electronic questionnaire, the provision of center-based services of most respondents were severely affected. Some of them launched online services but faced various constraints such as staff members' limited knowledge, insufficient technical support and service users' lacking required devices and poor internet connection. Hong Kong's experience shows that digital literacy needs to be embedded into the future health and social care training curriculum. Also, effective digital communication training packages need to be developed with the involvement of service users. Moreover, innovative approaches have become imperative for health and social care practitioners to deal with the Covid-19 pandemic. Future studies can investigate the impact of Covid-19 from the perspective of older respondents and on various types of social services. Also, qualitative research methods can be adopted to collect rich data for deeper understandings on the difficulties of both service providers and users on delivering and receiving internet-based health and welfare services. In short, future studies can examine service users' views on the impact of Covid-19 by using in-depth interviews. [ABSTRACT FROM AUTHOR]