Search

Noise measurements in light water reactor systems aid in generating validation data for integral point kinetic parameter predictions and monitoring parameters for reactor safety and safeguards. The CROCUS zero-power reactor has been used to produce both data types to date, using thermal neutron detectors to observe neutron noise and inorganic scintillators to observe gamma noise. Also, the cross-correlation of gamma and neutron noise has been investigated at CROCUS with separate gamma and neutron detectors. Organic scintillators can be used to cross-correlate gamma and neutron noise with only one detector type, within a single detector volume, and provide nanosecond timing resolution for time-correlated measurements. Dual-particle measurements require particle-type discrimination and are hence possible with organic scintillators since such detectors have the property of presenting statistically different pulse shapes for gamma rays and fast neutrons. The fine timing precision increases the signal-to-noise ratio relative to moderated thermal neutron detectors for correlated measurements and the dual-particle sensitivity allows for multiple modalities of estimating the prompt neutron decay constant. In this work, we present data obtained with 5.08 cm-length by 5.08 cm-diameter trans-stilbene cylindrical detectors set in the water reflector of CROCUS. Preliminary results estimate the prompt neutron decay constant to be (155 ±5) s−1 at delayed critical.

The PETALE experimental program in the CROCUS reactor intends to provide integral measurements on reactivity worth and dosimetry measurement to constrain nuclear data relative to stainless steel heavy reflectors. The experimental setup consists in eight successive plates of pure iron, pure nickel, pure chromium, or nuclear-grade stainless steel set at the close periphery of the core. The plates are interleaved with up to nine dosimeters that consist of thin activation foils with different possible materials to be sensitive to different ranges of the neutron spectrum. A precise measurement with a good estimation of the uncertainties and correlations is required, especially when comparing reaction rates, e.g. transmission measurement and/or spectral indices. The present work focuses on the validation of the dosimetry technics developed in preparation of this experimental program. Different aspects are discussed: monitors, efficiency calibration, self-absorption correction, self-shielding and nuclear data uncertainties. The different sources of uncertainties for the experiment-calculation comparisons are characterized, taking into account all the correlation between the different dosimeters. These correlations are a mandatory element for the aimed Bayesian assimilation in order to avoir overfitting when considering dosimeter providing a similar information.

At EPFL, the CROCUS reactor has been used to carry out experiments with vibrating fuel rods. The paper presents a first attempt to employ the measured data to validate CORE SIM+, a neutron noise solver developed at Chalmers University of Technology. For this purpose, the original experimental data are processed in order to extract the necessary information. In particular, detector recordings are scrutinized and detrended, and used to estimate CPSDs of detector pairs. These values are then compared with the ones derived from the CORE SIM+ simulations of the experiments. The main trend of the experimental data along with the values for some detectors are successfully reproduced by CORE SIM+. Further work is necessary on both the experimental and computational sides in order to improve the validation process.

The Horizon2020 European project CORTEX aims at developing an innovative core monitoring technique that allows detecting anomalies in nuclear reactors, such as excessive vibrations of core internals, flow blockage, or coolant inlet perturbations. The technique will be mainly based on using the fluctuations in neutron flux recorded by in-core and ex-core instrumentation, from which the anomalies will be differentiated depending on their type, location and characteristics. The project will result in a deepened understanding of the physical processes involved, allowing utilities to detect operational problems at a very early stage. In this framework, neutron noise computational methods and models are developed. In parallel, mechanical noise experimental campaigns are carried out in two zero-power reactors: AKR-2 and CROCUS. The aim is to produce high quality neutron noise-specific experimental data for the validation of the models. In CROCUS, the COLIBRI experimental program was developed to investigate experimentally the radiation noise induced by fuel rods vibrations. In this way, the 2018 first CORTEX campaign in CROCUS consisted in experiments with a perturbation induced by a fuel rods oscillator. Eighteen fuel rods located at the periphery of the core fuel lattice were oscillated between ±0.5 mm and ±2.0 mm around their central position at a frequency ranging from 0.1 Hz to 2 Hz. Signals from 11 neutron detectors which were set at positions in-core and ex-core in the water reflector, were recorded. The present article documents the results in noise level of the experimental campaign. Neutron noise levels are compared for several oscillation frequencies and amplitudes, and at the various detector locations concluding to the observation of a spatial dependency of the noise in amplitude.

The present article describes the preliminary validation study of simulated in-core and reflector n eutron spectra in preparation of oncoming experimental programs in the zeropower reactor CROCUS at EPFL. For this purpose, a set of activation foils were irradiated at three characteristic positions in the CROCUS reactor, and the subsequent activities were analyzed via γ spectrometry. The experimental setup was then modeled with the Monte Carlo neutron transport code Serpent2 and associated with an analysis tool to include the effect of the reactor power history during experiments. The comparison of calculated and measured reaction rates (C/E) indicates a general consistency (at 2σ) between calculated and measured spectra. However, offsets of C/E values were observed in (n, γ) reactions, up to 18% for 115In and 8% for 63Cu dosimeters. This could be caused by an unexpected isotopic composition, uncertainties in nuclear data, or the spectrometry analysis. In addition, a 100-groups spectrum unfolding was performed using the experimentally determined reaction rates and the Serpent2 spectra as the prior knowledge. The unfolded spectra were mainly adjusted in the thermal and fast ranges, while few modifications w ere m ade i n t he e pithermal r egion d ue t o the low contribution of epithermal neutrons in activation processes. Moreover, within energy groups where the capture reactions show resonant behavior, flux depletion (up to 38% as compared to the prior spectra) is observed due to the absence of self-shielding effect in the unfolding process. For this purpose, an unfolding method based on energy groups weighting is developed and tested.

Gamma rays in nuclear reactors, arising either from fission or decay processes, significantly contribute to the heating and dose of the reactor components. Zero power research reactors offer the possibility to measure gamma rays in a purely neutronic environment, allowing for validation experiments of computed spectra, dose estimates, reactor noise and prompt to delayed gamma ratios. This data then contributes to models, code validation and photo atomic nuclear data evaluation. In order to contribute to aforementioned experimental data, gamma detection capabilities are being added to the CROCUS reactor facility. The CROCUS reactor is a two-zone, uranium-fueled light water moderated facility operated by the Laboratory for Reactor Physics and Systems Behaviour (LRS) at the Swiss Federal Institute of Technology Lausanne (EPFL). With a maximum power of 100W, it is a zero power reactor used for teaching and research, most recently for intrinsic and induced neutron noise studies. For future gamma detection applications in the CROCUS reactor, an array of four detectors - two large 5”x10” Bismuth Germanate (BGO) and two smaller Cerium Bromide (CeBr3) scintillators - was acquired. The BGO detectors are to be arbitrarily positioned in the core reflector and out of the vessel for measurements at arbitrary distances. The CeBr3 detectors on the other hand are small enough to be set in the guide tubes of the control rods for in-core measurements. We present a study of the neutron and gamma flux in the core and reflector using the MCNP 6.2 and Serpent 2 Monte Carlo codes for coupled neutron and photon transport criticality calculations. More specifically, we investigate and compare predicted spectra as well as reactivity worth of different envisioned experimental setups. We further predict pulse height spectra as well as doses to the crystals with and without cadmium shielding to estimate allowable reactor powers with respect to detector radiation hardness. The results serve as basis for calibration and aid in the design and regulatory approval of the experiments.

The present article is an overview of developments and results regarding neutron noise measurements in current mode at the CROCUS zero power facility. Neutron noise measurements offer a non-invasive method to determine kinetic reactor parameters such as the prompt decay constant at criticality α = βeff / λ, the effective delayed neutron fraction βeff, and the mean generation time λ for code validation efforts. At higher detection rates, i.e. above 2×104 cps in the used configuration at 0.1 W, the previously employed pulse charge amplification electronics with BF3 detectors yielded erroneous results due to dead time effects. Future experimental needs call for higher sensitivity in detectors, higher detection rates or higher reactor powers, and thus a generally more versatile measurement system. We, therefore, explored detectors operated with current mode acquisition electronics to accommodate the need. We approached the matter in two ways: 1) By using the two compensated 10B-coated ionization chambers available in CROCUS as operational monitors. The compensated current signal of these chambers was extracted from coremonitoring output channels. 2) By developing a new current mode amplification station to be used with other available detectors in core. Characteristics and first noise measurements of the new current system are presented. We implemented post-processing of the current signals from 1)and 2) with the APSD/CPSD method to determine α. At two critical states (0.5 and 1.5 W), using the 10B ionization chambers and their CPSD estimate, the prompt decay constant was measured after 1.5 hours to be α=(156.9 ± 4.3) s-1 (1σ). This result is within 1σ of statistical uncertainties of previous experiments and MCNPv5-1.6 predictions using the ENDF/B-7.1 library. The newsystem connected to a CFUL01 fission chamber using the APSDestimate at 100 mW after 33 min yielded α = (160.8 ± 6.3) s-1, also within 1σ agreement. The improvements to previous neutron noise measurementsinclude shorter measurement durations that can achievecomparable statistical uncertainties and measurements at higherdetection rates.

Miniature fission chambers are tools suited for instrumenting experimental reactors, allowing online and in-core neutron measurements of quantities such as fission rates or reactor power. A new set of such detectors was produced by CEA to be used for the next experimental program at the EOLE facility starting in 2013. Some of these detectors will be employed in pulse mode for absolute measurements, which require calibration. The calibration factor is expressed in mass units and is thus called “effective mass”. A calibration campaign was conducted in December 2012 at the SCK\bulletCEN BR1 facility within the framework of the scientific cooperation VEP (VENUS-EOLE-PROTEUS) between SCK\bulletCEN, CEA and PSI. In order to improve the calibration method, two steps were taken. First, a new characterisation of the thermal flux cavity and the MARK3 neutron flux conversion device carried out by SCK\bulletCEN allowed using calculated effective cross sections for determining detectors effective masses. Dosimetry irradiations were performed in situ in order to determine the neutron flux level and provide a link to the metrological standard. Second, two fission chambers were also calibrated at the CEA CALIBAN reactor (fast neutron spectrum) using the same method so that the results could be compared with the results obtained at the SCK\bulletCEN. This paper proposes to present both the calibration method and recent improvements on uncertainty reduction and biases evaluation. The results and uncertainties obtained in both CALIBAN and BR1 reactors will be compared and discussed. [ABSTRACT FROM PUBLISHER]

Autonomous nuclear reactor monitoring is a key aspect of the International Atomic Energy Agency's strategy to ensure nonproliferation treaty compliance. From the rise of small modular reactor technology, decentralized nuclear reactor fleets may strain the capacities of such monitoring and requires new approaches. We demonstrate the superior capabilities of a gamma detection system to monitor the criticality of a zero power nuclear reactor from beyond typical vessel boundaries, offering a powerful alternative to neutron-based systems by providing direct information on fission chain propagation. Using the case example of the research reactor CROCUS, we demonstrate how two bismuth germanate scintillators placed outside the reactor vessel can precisely observe reactor criticality using so called noise methods and provide core status information in seconds. Our results indicate a wide range of applications due to the newly gained geometric flexibility that could find use in fields beyond nuclear safety., (© 2024. The Author(s).)