Search

INTRODUCTION Slotted nails allow a connection to a total hip arthroplasty (THA) stem and act as intramedullary load carrier. This study compares construct stiffness, cycles to failure and failure load between a retrograde slotted femur nail construct docked to a THA stem and a lateral locking plate in a human periprosthetic femur fracture model. MATERIALS AND METHODS In seven pairs of fresh-frozen human anatomic femora with cemented THA, a transverse osteotomy was set simulating a Vancouver type B1 fracture. The femora were instrumented pairwise with either a retrograde slotted nail coupled to the prosthesis stem, or a locking plate plus a locking attachment plate. Four-point mediolateral bending, torsional and axial bending construct stiffness was investigated via non-destructive tests. Cyclic testing under progressively increasing physiologic loading was performed at 2 Hz until catastrophic construct failure. RESULTS Mediolateral bending stiffness did not differ significantly between the two groups (P=0.17) but exhibited a biphasic profile with significantly increased stiffness in both groups (P

Aims Fixation of osteoporotic proximal humerus fractures remains challenging even with state-of-the-art locking plates. Despite the demonstrated biomechanical benefit of screw tip augmentation with bone cement, the clinical findings have remained unclear, potentially as the optimal augmentation combinations are unknown. The aim of this study was to systematically evaluate the biomechanical benefits of the augmentation options in a humeral locking plate using finite element analysis (FEA). Methods A total of 64 cement augmentation configurations were analyzed using six screws of a locking plate to virtually fix unstable three-part fractures in 24 low-density proximal humerus models under three physiological loading cases (4,608 simulations). The biomechanical benefit of augmentation was evaluated through an established FEA methodology using the average peri-screw bone strain as a validated predictor of cyclic cut-out failure. Results The biomechanical benefit was already significant with a single cemented screw and increased with the number of augmented screws, but the configuration was highly influential. The best two-screw (mean 23%, SD 3% reduction) and the worst four-screw (mean 22%, SD 5%) combinations performed similarly. The largest benefits were achieved with augmenting screws purchasing into the calcar and having posteriorly located tips. Local bone mineral density was not directly related to the improvement. Conclusion The number and configuration of cemented screws strongly determined how augmentation can alleviate the predicted risk of cut-out failure. Screws purchasing in the calcar and posterior humeral head regions may be prioritized. Although requiring clinical corroborations, these findings may explain the controversial results of previous clinical studies not controlling the choices of screw augmentation.

Background and Objectives: Hip fractures constitute the most debilitating complication of osteoporosis with steadily increasing incidences in the aging population. Their intramedullary nailing can be challenging because of poor anchorage in the osteoporotic femoral head. Cement augmentation of Proximal Femoral Nail Antirotation (PFNA) blades demonstrated promising results by enhancing cut-out resistance in proximal femoral fractures. The aim of this study was to assess the impact of augmentation on the fixation strength of TFN-ADVANCEDTM Proximal Femoral Nailing System (TFNA) blades and screws within the femoral head and compare its effect when they are implanted in centre or anteroposterior off-centre position. Materials and Methods: Eight groups were formed out of 96 polyurethane low-density foam specimens simulating isolated femoral heads with poor bone quality. The specimens in each group were implanted with either non-augmented or cement-augmented TFNA blades or screws in centre or anteroposterior off-centre positions, 7 mm anterior or posterior. Mechanical testing was performed under progressively increasing cyclic loading until failure, in setup simulating an unstable pertrochanteric fracture with a lack of posteromedial support and load sharing at the fracture gap. Varus-valgus and head rotation angles were monitored. A varus collapse of 5° or 10° head rotation was defined as a clinically relevant failure. Results: Failure load (N) for specimens with augmented TFNA head elements (screw/blade centre: 3799 ± 326/3228 ± 478, screw/blade off-centre: 2680 ± 182/2591 ± 244) was significantly higher compared with respective non-augmented specimens (screw/blade centre: 1593 ± 120/1489 ± 41, screw/blade off-centre: 515 ± 73/1018 ± 48), p &lt, 0.001. For both non-augmented and augmented specimens failure load in the centre position was significantly higher compared with the respective off-centre positions, regardless of the head element type, p &lt, 0.001. Augmented off-centre TFNA head elements had significantly higher failure load compared with non-augmented centrally placed implants, p &lt, 0.001. Conclusions: Cement augmentation clearly enhances the fixation stability of TFNA blades and screws. Non-augmented blades outperformed screws in the anteroposterior off-centre position. Positioning of TFNA blades in the femoral head is more forgiving than TFNA screws in terms of failure load.

Background : Fracture fixation has advanced significantly with the introduction of locked plating and minimally invasive surgical techniques. However, healing complications occur in up to 10% of cases, of which a significant portion may be attributed to unfavorable mechanical conditions at the fracture. Moreover, state-of-the-art plates are prone to failure from excessive loading or fatigue. A novel biphasic plating concept has been developed to create reliable mechanical conditions for timely bone healing and simultaneously improve implant strength. This paper introduces the novel fixation concept and presents preclinical results from a large animal study. Methods : Twenty-four sheep underwent a mid-diaphyseal osteotomy stabilized with either the novel biphasic plate fixator or a control locking plate. Different fracture patterns regarding orientation and localization were investigated. Animals were free to fully bear weight during the post-operative period. After 12 weeks, the healing fractures were evaluated for bone formation using micro-computer tomography and strength and stiffness using biomechanical testing. Additionally, histological evaluation of soft tissue samples with respect to metal wear debris was performed. Results : No plate deformation or failures were observed under full weight bearing with the biphasic plate. Defects stabilized with the biphasic plate demonstrated robust callus formation compared to control group. Torsion tests after plate removal revealed no statistical difference in peak torsion to failure and stiffness for the different fracture patterns stabilized with the biphasic plate. However, the biphasic plate group specimens were 45% stronger (p=0.002) and 48% stiffer (p=0.007) than the controls. No histological signs of metal wear due to the biphasic feature could be found. Conclusions : The biphasic plate concept is aimed at improving the biomechanics of locked plating. The results of this large animal study demonstrate the feasibility and clinical potential of this novel stabilization concept.

ZusammenfassungDie Versorgung osteoporotischer Frakturen mittels metallischer Implantate erreicht zunehmend ihre Grenzen. Eine mögliche Lösung, um eine ausreichende Verankerung des Implantats sicherzustellen, ist die Verstärkung der geschwächten Knochenstruktur mit Knochenzement, die sog. Implantataugmentation. Hierfür kommen meist Acrylate (PMMA) oder resorbierbare Kalziumphosphatzemente (CaP) zum Einsatz. PMMA-Zemente besitzen ausgewogene mechanische Eigenschaften, sind einfach zu handhaben und lassen sich gut und sicher injizieren. Allerdings geht die Aushärtung von PMMA mit Entstehung von Wärme einher. Es konnte aber gezeigt werden, dass die für die Implantataugmentation benötigten kleinen Mengen an PMMA nicht zu kritischen Temperaturen im umliegenden Gewebe führen. CaP-Zemente besitzen eine sehr gute Biokompatibilität, erwärmen sich bei der Aushärtung nicht und sind resorbierbar. Wegen der verminderten mechanischen Eigenschaften wird jedoch oft geraten, die derzeit verfügbaren CaP-Zemente eher an nicht oder wenig belasteten Stellen anzuwenden. Neuere Entwicklungen deuten jedoch darauf hin, dass in Zukunft deutlich bessere Eigenschaften von CaP-Zementen zu erwarten sind. Mit der kurz- bis mittelfristig klaren Zunahme von Altersfrakturen bildet die Implantataugmentation mit CaP oder Acrylat eine interessante Möglichkeit, um den kommenden Problemen zu begegnen.

Internal fixation by plate osteosynthesis is the gold standard treatment for distal femur fractures. Despite improvements that preserve the biological conditions for bone healing, there are concerns standard locked plating constructs may be overly stiff. Biphasic plating is a novel concept designed to provide suitable fracture motion and increased implant strength to support early full weight-bearing. This study aims to demonstrate that the Biphasic Plate can be incorporated into a pre-contoured distal femur plate while providing adequate flexibility and increased implant strength. The mechanical performance of the Biphasic Plate (BP) was investigated in comparison to a standard locking plate for the distal femur (LCP-DF). Constructs were formed by mounting the implants on a bone substitute. The construct stiffness and strength under axial loading and the magnitude of interfragmentary movement were determined using finite element analysis. The Biphasic Plate exhibited a bi-linear stiffness response; at low loads, the BP construct was 55% more compliant and at high loads 476% stiffer than the LCP-DF. The Biphasic Plate provided more consistent interfragmentary movement over a wider loading range. At partial weight-bearing loads, the Biphasic Plate produced larger interfragmentary movements (0.18 vs. 0.04 mm). However, at loads equivalent to full weight-bearing, the maximum movements were substantially smaller than the LCP-DF construct (1.5 vs. 3.5 mm). The increased flexibility at low loads was provided without sacrificing implant strength with peak stress in the Biphasic Plate 63% lower than the LCP-DF construct. The biphasic plating concept can be successfully incorporated into anatomically contoured distal femur plates while providing adequate flexibility and increasing implant strength.

Osteoporotic hip fractures are an increasing problem in an ageing population. They result in high morbidity, mortality and high socioeconomic costs. For patients with poor bone quality, prophylactic augmentation of the proximal femur might be an option for fracture prevention. In two groups of paired human femora the potential of limited polymethyl-methacrylate (PMMA) augmentation (11–15 ml) in a V-shape pattern and the insertion of a proximal femur nail antirotation (PFNA) blade were investigated. The testing was carried out pair wise simulating the single leg stand. The untreated femur in each pair served as control. An axial load was applied until failure. Load displacement parameters and temperature increase during the augmentation process were recorded. In the PMMA group no significant difference was found between the augmented and non-augmented specimen concerning load to failure (p = 0.35) and energy to failure (p = 0.9). A median temperature increase of 9.5 °C was observed in the augmented specimen. A significant correlation was found between the amount of applied PMMA and the temperature increase (Cor. Coef. = 0.82, p = 0.042). In the PFNA group, a significant decrease of load to failure and a non-significant decrease of energy to failure were observed (p = 0.037 and p = 0.075). Limited V-shaped PMMA augmentation and PFNA blade insertion did not show any improvement in failure load or energy to failure. Volumes of up to 15 ml PMMA did not cause a critical surface temperature increase.

Migration profile of helical blades differs from conventional screw design. Tip-apex distance (TAD) greater than 25 mm is associated with early failure in hip screws. This study investigates the effect of a reduced TAD on helical blade fixation. Six pairs of human femoral heads were used. Bone mineral density (BMD) was determined by pQCT. Local bone quality was evaluated by breakaway torque. Helical blades were implanted with TAD of 20 mm (normal) and 6 mm (reduced). Specimens were cyclically tested under progressively increasing physiologic loading at 2 Hz with starting peak force of 1'000N, increasing by 0.1N/cycle. Implant migration was monitored by radiographs every 250 cycles. Paired Student's t-test and Spearman rank correlation coefficient were used for statistical evaluation (p

Femoral neck fractures in the elderly are a common problem in orthopedics. Augmentation of screw fixation with bone cement can provide better stability of implants and lower the risk of secondary displacement. This study aimed to investigate whether cement augmentation of three cannulated screws in non-displaced femoral neck fractures could increase implant fixation. A femoral neck fracture was simulated in six paired human cadaveric femora and stabilized with three 7.3 mm cannulated screws. Pairs were divided into two groups: conventional instrumentation versus additional cement augmentation of screw tips with 2 ml TraumacemV+ each. Biomechanical testing was performed by applying cyclic axial load until failure. Failure cycles, axial head displacement, screw angle changes, telescoping and screw cut-out were evaluated. Failure (15 mm actuator displacement) occurred in the augmented group at 12,500 cycles (± 2,480) compared to 15,625 cycles (± 4,215) in the non-augmented group (p = 0.041). When comparing 3 mm vertical displacement of the head no significant difference (p = 0.72) was detected between the survival curves of the two groups. At 8,500 load-cycles (early onset failure) the augmented group demonstrated a change in screw angle of 2.85° (± 0.84) compared to 1.15° (± 0.93) in the non-augmented group (p = 0.013). The results showed no biomechanical advantage with respect to secondary displacement following augmentation of three cannulated screws in a non-displaced femoral neck fracture. Consequently, the indication for cement augmentation to enhance implant anchorage in osteoporotic bone has to be considered carefully taking into account fracture type, implant selection and biomechanical surrounding. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 9999:XX–XX, 2015.

Objectives The benefits of cement augmentation with fixation of osteoporotic pertrochanteric fractures have been previously demonstrated. The objective of this study was 3-fold: (1) To quantify the intraosseous pressure produced during cement augmentation of the perforated proximal femoral nail antirotation (PFNA) blades; (2) To assess whether the pressure generated is influenced by the injection rate; and (3) To assess the amount of force applied during the injection. Methods Six pairs of human cadaveric femurs were used in the study. A basicervical osteotomy was performed, and the heads were instrumented with the PFNA blade. Each pair was randomly assigned into 1 of 2 groups: slow versus rapid injection with polymethylmethacrylate (PMMA) cement. In the slow group, the augmentation was performed using 6 consecutive 1 mL injections, each over 10 seconds. In the rapid group, each 1 mL injection was performed over 5 seconds. For intraosseous pressure measurements, transmitters were inserted to a depth of 5 mm at both the superior and inferior apices of the head. The reaction forces on the syringe were measured as well. Results There were no significant differences between the slow and rapid injection rates with respect to the peak pressures measured at the 6 time points immediately after cement injection. In both groups, elevations in pressure were transient and returned to baseline values within 30 seconds. The highest pressure recorded in the slow group was 37.3 and 30.7 mm Hg in the rapid group. The force required after each sequential injection increased in both groups; however, significantly higher forces were required to inject cement over 5 than 10 seconds (P = 0.036). Conclusions This in vitro model is the first one to demonstrate that femoral head cement augmentation is associated with a small transient increase in intraosseous pressure with sequential fast and slow 1 mL injections of up to 6 mL PMMA. We conclude that cement augmentation of the perforated PFNA blade carries a low risk of pressure-induced avascular necrosis.

Several studies proved the beneficial effect of cement augmentation of proximal femoral nail antirotation (PFNA) blades on implant purchase in osteoporotic bone. We investigated the effect of different localizations and amounts of bone cement. Polyurethane foam specimens were instrumented with a PFNA blade and subsequently augmented with PMMA bone cement. Eight study groups were formed based on localization and amount of cement volume related to the blade. All specimens underwent cyclic loading with physiological orientation of the force vector until construct failure. Foam groups were compared between each other and to a cadaveric control group. The experiments revealed a significant dependency of implant purchase on localization and amount of cement. Biomechanically favorable cement positions were found at the implant tip and at the cranial side. However, none of the tested augmentation patterns performed significantly inferior to the cadaveric benchmark. These findings will allow surgeons to further reduce the amount of injected PMMA, decreasing the risk of cement leakage or cartilage damage.

Osteoporotic fractures of the distal femur (primary as well as periprosthetic) are a growing problem in today’s trauma and orthopaedic surgery. Therefore, this feasibility study should identify the biomechanical potential of a (commercially available) spiral blade in the distal femur as compared to a single screw without any additional plate fixation. Additionally, the influence of cement augmentation was investigated. An artificial low density bone model was either instrumented with a perforated spiral blade or a 5 mm locking screw only. Additionally, the influence of 1 ml cement augmentation was investigated. All specimens were tested with static pull-out and cyclic loading (50 to 250 N with an increment of 0.1 N/cycle). In the non-augmented groups, the mean pull-out force was significantly higher for the blade fixation (p

Subchondral screw abutment in osteosynthesis of joint fractures is an effective method to achieve sufficient screw grip. In this study we investigated if subchondral screw placement is possible without harming the overlying subchondral plate and joint cartilage iatrogenic. A 3.5-mm conventional steel screw was placed in the tibia of ten sheep in distances between 1 and 7 mm beneath the joint cartilage. After a follow up of two and four months, evaluation of the subchondral bone and joint cartilage was performed by means of a histological osteoarthritis score, HRpQCT imaging and determination of the glycosaminoglycan content in the cartilage. The control group was the contralateral knee of the same animal. Histomorphometric evaluation of the Mankin osteoarthritis score revealed no significant difference compared to the control after two (p = 0.102) and four months (p = 0.429). No correlation between distance of the screw to the cartilage and histological scoring was found (p = 0.658, R2 = 0.04 after two months and p = 0.171, R2 = 0.18 after four months). HRpQCT measurements of the subchondral thickness between screw and cartilage after two (p = 0.05) and four months (p = 0.424) showed no significant difference. Mean glycosaminoglycan content in the treatment group compared to the control after two months (p = 0.25) and four months (p = 0.523) was not significant different. In conclusion subchondral screw abutment did not damage the joint cartilage after a two- and four-month follow up in this sheep model.

The high incidence of secondary hip fractures and the associated markedly increased mortality call for preventive actions that could help to avoid these injuries. By providing immediate strengthening and not relying on patient compliance, internal prophylactic augmentation of the osteoporotic proximal femur may overcome the main limitations of systemic bone drugs and wearable protective pads. However, such a method would have to provide sufficient and reliable strengthening effect with minimal risks and side effects to justify the need of an invasive treatment. The requirements for an internal reinforcement approach are thus strict and include mechanical, biological, clinical, ethical and financial criteria. Here we first attempt to describe the properties of an ideal augmentation method. Previously published methodologies and techniques developed at our research institute, including approaches using cements, metals, other materials or combined approaches, are then reviewed and evaluated according to these aspects. We conclude that none of the discussed methodologies appears to be able to deliver a sufficiently high gain-versus-risk ratio that could justify the clinical application and thus augmentation of the osteoporotic proximal femur remains a challenge. Finally, we provide suggestions for the development and evaluation of future strategies.

The increasing problems in the field of osteoporotic fracture fixation results in specialized implants as well as new operation methods, for example, implant augmentation with bone cement. The aim of this study was to determine the biomechanical impact of augmentation in the treatment of osteoporotic distal femur fractures. Seven pairs of osteoporotic fresh frozen distal femora were randomly assigned to either an augmented or nonaugmented group. In both groups, an Orthopaedic Trauma Association 33 A3 fractures was fixed using the locking compression plate distal femur and cannulated and perforated screws. In the augmented group, additionally, 1 mL of polymethylmethacrylate cement was injected through the screw. Prior to mechanical testing, bone mineral density (BMD) and local bone strength were determined. Mechanical testing was performed by cyclic axial loading (100 N to 750 N + 0.05N/cycle) using a servo-hydraulic testing machine. As a result, the BMD as well as the axial stiffness did not significantly differ between the groups. The number of cycles to failure was significantly higher in the augmented group with the BMD as a significant covariate. In conclusion, cement augmentation can significantly improve implant anchorage in plating of osteoporotic distal femur fractures.

The incidence of osteoporotic proximal tibial fractures has increased during the last 2 decades. A promising approach in osteoporotic fracture fixation is polymethylmethacrylate-based cement augmentation of implants to gain better implant purchase in the bone. This study investigates the biomechanical benefits of screw augmentation in less invasive stabilization system-proximal lateral tibial (LISS-PLT) plates in cadaveric extraarticular comminuted proximal tibial fractures (OTA-41-A3.3).Standardized extraarticular proximal tibial fractures were stabilized with the LISS-PLT plate in 6 paired osteoporotic cadaveric tibiae. Bone mineral density was measured with high-resolution, quantitative computed tomography scans to identify bone quality. In the augmented group, the 5 proximal screws of the LISS-PLT plate were augmented with 1 mL of bone cement each, whereas the contralateral tibia was instrumented conventionally as the control. Cyclic axial loading was applied to each specimen with a starting load of 150 N, using a ramp of 0.05 N per cycle to 10-mm axial displacement. Varus displacement was identified from anterior-posterior radiographs.Bone mineral density showed no significant difference between the 2 groups (P = 0.47). The nonaugmented group reached 9417 load cycles (SD 753) until failure, compared with 14,792 load cycles (SD 2088) in the augmented group (P = 0.002). In the early-onset failure (deformation at 8250 load cycles), varus displacement was significantly smaller in the augmented group (0.46 degrees, SD 0.6) than in the nonaugmented group (3.23 degrees, SD 1.7) (P = 0.01).This biomechanical study showed that cement augmentation of the LISS-PLT plate screws in osteoporotic proximal extraarticular tibial fractures significantly lowers the propensity toward screw migration and secondary varus displacement.

Introduction Proximal humerus fracture fixation can be difficult because of osteoporosis making it difficult to achieve stable implant anchorage in the weak bone stock even when using locking plates. This may cause implant failure requiring revision surgery. Cement augmentation has, in principle, been shown to improve stability. The aim of this study was to investigate whether augmentation of particular screws of a locking plate aimed at a region of low bone quality is effective in improving stability in a proximal humerus fracture model. Materials and methods Twelve paired human humerus specimens were included. Quantitative computed tomography was performed to determine bone mineral density (BMD). Local bone quality in the direction of the six proximal screws of a standard locking plate (PHILOS, Synthes) was assessed using mechanical means (DensiProbe™). A three-part fracture model with a metaphyseal defect was simulated and fixed with the plate. Within each pair of humeri the two screws aimed at the region of the lowest bone quality according to the DensiProbe™ were augmented in a randomised manner. For augmentation, 0.5 ml of bone cement was injected in a screw with multiple outlets at its tip under fluoroscopic control. A cyclic varus-bending test with increasing upper load magnitude was performed until failure of the screw–bone fixation. Results The augmented group withstood significantly more load cycles. The correlation of BMD with load cycles until failure and BMD with paired difference in load cycles to failure showed that augmentation could compensate for a low BMD. Discussion and conclusion The results demonstrate that augmentation of screws in locked plating in a proximal humerus fracture model is effective in improving primary stability in a cyclic varus-bending test. The augmentation of two particular screws aimed at a region of low bone quality within the humeral head was almost as effective as four screws with twice the amount of bone cement. Screw augmentation combined with a knowledge of the local bone quality could be more effective in enhancing the primary stability of a proximal humerus locking plate because the effect of augmentation can be exploited more effectively limiting it to the degree required.

Background The treatment of proximal humerus fractures in patients with poor bone quality remains a challenge in trauma surgery. Augmentation with polymethylmethacrylate (PMMA) cement is a possible method to strengthen the implant anchorage in osteoporotic bone and to avoid loss of reduction and reduce the cut-out risk. The polymerisation of PMMA during cement setting leads, however, to an exothermic reaction and the development of supraphysiological temperatures may harm the bone and cartilage. This study addresses the issue of heat development during augmentation of subchondrally placed proximal humerus plate screws with PMMA and the possible risk of bone and cartilage necrosis and apoptosis. Methods Seven fresh frozen humeri from geriatric female donors were instrumented with the proximal humerus interlocking system (PHILOS) plate and placed in a 37 °C water bath. Thereafter, four proximal perforated screws were augmented with 0.5 ml PMMA each. During augmentation, the temperatures in the subchondral bone and on the articular surface were recorded with K-type thermocouples. The measured temperatures were compared to threshold values for necrosis and apoptosis of bone and cartilage reported in the literature. Results The heat development was highest around the augmented tips of the perforated screws and diminished with growing distance from the cement cloud. The highest temperature recorded in the subchondral bone reached 43.5 °C and the longest exposure time above 42 °C was 86 s. The highest temperature measured on the articular surface amounted to 38.6 °C and the longest exposure time above 38 °C was 5 min and 32 s. Conclusion The study shows that augmentation of the proximal screws of the PHILOS plate with PMMA leads to a locally limited development of supraphysiological temperatures in the cement cloud and closely around it. The critical threshold values for necrosis and apoptosis of cartilage and subchondral bone reported in the literature, however, are not reached. In order to avoid cement extravasation, special care should be taken in detecting perforations or intra-articular cracks in the humeral head.

Augmentation of implants with polymethylmethacrylate (PMMA) bone cement in osteoporotic fractures is a promising approach to increase implant purchase. Side effects of PMMA for the metaphyseal bone, particularly for the adjacent subchondral bone plate and joint cartilage, have not yet been studied. The following experimental study investigates whether subchondral PMMA injection compromises the homeostasis of the subchondral bone and/or the joint cartilage. Ten mature sheep were used to simulate subchondral PMMA injection. Follow-ups of 2 (4 animals) and 4 (6 animals) months were chosen to investigate possible cartilage damage and subchondral plate alterations in the knee. Evaluation was completed by means of high-resolution peripheral quantitative computed tomography (HRpQCT) imaging, histopathological osteoarthritis scoring, and determination of glycosaminoglycan content in the joint cartilage. Results were compared with the untreated contralateral knee and statistically analyzed using nonparametric tests. Evaluation of the histological osteoarthritis score revealed no obvious cartilage damage for the treated knee; median histological score after 2 months 0 (range 4), after 4 months 1 (range 5). There was no significant difference when compared with the untreated control site after 2 and 4 months (P = 0.23 and 0.76, respectively). HRpQCT imaging showed no damage to the metaphyseal trabeculae. Glycosaminoglycan measurements of the treated joint cartilage after 4 months revealed no significant difference compared with the untreated cartilage (P = 0.24). The findings of this study support initial clinical observation that PMMA implant augmentation of metaphyseal fractures appears to be a safe procedure for fixation without harming the subchondral bone plate and adjacent joint cartilage.