Search

Diffuse soil contamination with heavy metals and Cd in particular is a matter of serious concern. Application of conventional remediation methods usually is not feasible due to the large territories and relatively low heavy metal content. Thus, phytoremediation is seen as an alternative. Rapeseed was grown on Cd and Zn contaminated as well as clean soil under the greenhouse conditions. Solid and liquid nitrogen fertilizers were applied during the pot experiment in order to test their influence on heavy metal accumulation in plant tissues. Vegetative parameters were measured four times during the pot experiment and it was concluded, that the elevated concentrations of Cd and Zn in the soil did not disrupt the development of rapeseed plants. Furthermore, plants from contaminated soil produced significantly bigger seeds in comparison to plants from uncontaminated soil. Calculated Bioconcentration factors for rapeseed grown on Cd and Zn contaminated soil in all cases were below unity, thus possibility to use this plant species for phytoextraction purposes is limited, but it can be successfully grown on contaminated land as an energy crop. Application of nitrogen fertilizers had a significant effect on heavy metal accumulation and decreased Cd and Zn concentrations in rapeseed roots and stems with leaves were recorded. Accumulation differences between the liquid and solid fertilizer applications were negligible. [ABSTRACT FROM AUTHOR]

Utilization of bottom ash in road construction may lead to a release of contaminants that can affect the soil of the swales constructed along these roads. Column tests were performed to evaluate the retention behavior of Cu, Cr, Zn, and Pb, originating from municipal solid waste incineration (MSWI) bottom ash leachate, in two substrates: peat and mould (a cultural soil). A chemical sequential extraction method was used to predict the risk associated with the release of the retained elements with modifications of environmental conditions. Apart from the dissolution of organic matter (OM), ash leachate properties hindered the metal transport from peat. Mould was efficient only in removing Zn, making it a less favorable substrate for the leachate control along the roads. Readily soluble forms made up a minor fraction of the retained metals in peat, reducing the risk of metal release due to ion exchange and pH drop. Changes in redox potential might be the main cause of Zn desorption from peat as the Fe-Mn oxides were the main scavengers for this metal. Oxidation of OM would be the primary reason of Cu and Cr release, while for Pb both fractions (Fe-Mn oxides and OM) might equally contribute to the metal discharge. [ABSTRACT FROM AUTHOR]

Improper management of wood impregnation chemicals and treated wood has led to soil contamination at many wood treatment sites, particularly with toxic substances like creosote oil and chromated copper arsenate (CCA). The simultaneous presence of these pollutants complicates the choice of soil remediation technologies, especially if they are to be applied in situ. In this laboratory study, we attempted to immobilise arsenic (As) and simultaneously degrade polycyclic aromatic hydrocarbons (PAHs) (constituents of creosote oil) by applying a modified electrochemical oxidation method. The supply of iron (Fe) amendments in contaminated soil was done using corroding Fe electrodes as an Fe source and applying an alternating polarity electrical current. Soil with a large fraction of organic matter (25%) and containing 505 mg kg -1 As and 5160 mg kg -1 16-PAHs was placed in Plexiglas cells equipped with porewater samplers and an iron electrode pair connected to a power supply unit. The porewater and percolating solution were periodically sampled and analysed over an 8-week period. The modified electrochemical soil treatment led to a decrease in the total concentration of 16-PAHs in soil by 56-68%. The amount of poorly crystalline Fe oxides in the soil substantially increased, especially close to the electrodes, enabling 76-89% of As to be bound to this most reactive Fe fraction. Nevertheless, over 10% of soil As remained in the most soluble and available fraction (exchangeable), most likely due to the decline in soil redox potential over time. This study suggests that electrochemical oxidation of organic soil with mixed contaminants could be used for in situ soil remediation but needs further improvement to achieve more efficient As immobilisation., Competing Interests: Declarations. Ethical approval, consent to participate, and consent for publication: This study did not require ethical approval as it does not involve the use of human participants or animals and did not involve any interactions or interventions with living subjects. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

Trichloroethylene (TCE) poses a significant environmental threat in groundwater and soil, necessitating effective remediation strategies. Phytoremediation offers a cost-effective and environmentally friendly approach to remediation. However, the mechanisms governing plant uptake, volatilisation, and degradation of TCE remain poorly understood. This review explores the mechanisms of TCE phytoremediation, metabolic pathways, and influencing factors, emphasizing future research directions to improve the understanding of TCE phytoremediation. The results showed that although the proportion of TCE phytovolatilisation is limited, it is important at sites chronically contaminated with TCE. The rhizosphere is a key microzone for pollutant redox reactions that significantly enhance its effectiveness when its characteristics are fully utilised and manipulated through reinforcement. Future research should focus on manipulating microbial communities through methods such as the application of endophytic bacteria and genetic modification. However, practical applications are in their infancy and further investigation is needed. Furthermore, many findings are based on non-uniform parameters or unstandardised methods, making them difficult to compare. Therefore, future studies should provide more standardised experimental parameters and employ accurate and standardised methods to develop suitable prediction models, enhancing data comparability and deepening our understanding of plant detoxification mechanisms., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

There are large masses of coal tar asphalt present in old roads, containing high concentrations of polycyclic aromatic hydrocarbons (PAHs). Uncertainty surrounding the risk they pose causes problems during road reconstruction and for the reuse of the asphalt present. To help elucidate potential risks, a parsimonious linear equilibrium partitioning model for the bioavailability of PAHs in soils contaminated by tar asphalt particles was developed. Furthermore, a set of partitioning coefficients for PAHs between sampled coal tar binders and water were determined experimentally, as well as measurements of freely dissolved concentrations using polyoxymethylene samplers in batch tests and column recirculation experiments with various mixtures of different soils (peat and sandy loam) and tar asphalts. The model predictions of freely dissolved concentrations were conservative and within an order of magnitude of measurements in both batch and column tests. The model presented here only relies on soil organic carbon content and the fraction coal tar binder in the soil to model PAH partitioning. This model could be used for more realistic. Low tier risk assessments towards rational prioritization of sensitive areas for risk reduction efforts., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Although landfilling is environmentally and economically unsustainable, it is the dominant soil remediation method in EU member states. This paper describes part of a study on mixed contaminants that investigated the stabilisation of arsenic (As) in contaminated soil in an outdoor box experiment with electrokinetic treatment (EK). The experiment was conducted in two 1 m 3 boxes, each containing a 20 cm bottom layer of sand, overlaid with 20 cm of peat. In EK, a pulsating, low-voltage current was applied with the intention of corroding the zerovalent iron (Fe) electrodes, migrating ionic Fe species, and forming secondary iron minerals, thereby immobilizing As. Porewater samples were collected over two seasons to determine whether the treatment decreased the concentration of dissolved As. Sequential extraction was performed on the soil samples to determine whether the fraction of Fe-bound As increased. Reed canary grass was planted in one of the boxes during the second season and analysed for As uptake. The results showed that the treatment decreased the porewater As concentration in sand by 50-54 %, while the concentration of Fe increased. The sequential extraction of sand showed that the fraction of As bound to poorly crystalline Fe oxides increased during this time. This treatment effect was less visible in the peat. Moreover, the exchangeable As fraction increased in both peat and sand, most likely because of the decrease in redox potential at the end of the experiment. The plants grown in treated soil accumulated less As than those grown in untreated soil, indicating that the phytoavailable As fraction decreased. This study showed that EK remediation can be a suitable in situ remediation technique, mostly in sand. Future research should focus on redox control to further optimise EK remediation and ensure long-term As stability in treated soils., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Jurate Kumpiene reports financial support was provided by Horizon 2020 European Innovation Council Fast Track to Innovation. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

The current study evaluated a three-stage treatment to remediate PFAS-contaminated soil. The treatment consisted of soil washing, foam fractionation (FF), and electrochemical oxidation (EO). The possibility of replacing the third stage, i.e., EO, with an adsorption process was also assessed. The contamination in the studied soils was dominated by perfluorooctane sulfonate (PFOS), with a concentration of 760 and 19 μg kg -1 in soil I and in soil II, accounting for 97 % and 70 % of all detected per-and polyfluoroalkyl substances (PFAS). Before applying a pilot treatment of soil, soil washing was performed on a laboratory scale, to evaluate the effect of soil particle size, initial pH and a liquid-to-soil ratio (L/S) on the leachability of PFAS. A pilot washing system generated soil leachate that was subsequently treated using FF and EO (or adsorption) and then reused for soil washing. The results indicated that the leaching of PFAS occurred easier in 0.063-1 mm particles than in the soil particles having a size below 0.063 mm. Both alkaline conditions and a continual replacement of the leaching solution increased the leachability of PFAS. The analysis using one-way ANOVA showed no statistical difference in means of PFOS washed out in laboratory and pilot scales. This allowed estimating twenty washing cycles using 120 L water to reach 95 % PFOS removal in 60 kg soil. The aeration process removed 95-99 % PFOS in every washing cycle. The EO and adsorption processes achieved similar results removing up to 97 % PFOS in concentrated soil leachate. The current study demonstrated a multi-stage treatment as an effective and cost-efficient method to permanently clean up PFAS-contaminated soil., Competing Interests: Declaration of competing interest The authors affirm that there are no recognized conflicting financial interests or personal affiliations that might have seemed to exert any influence on the work detailed in this paper., (Copyright © 2023 The Authors. Published by Elsevier B.V. All rights reserved.)

Per- and polyfluoroalkyl substances (PFAS) are stable organic chemicals, which have been used globally since the 1940s and have caused PFAS contamination around the world. This study explores perfluorooctanoic acid (PFOA) enrichment and destruction by a combined method of sorption/desorption and photocatalytic reduction. A novel biosorbent (PG-PB) was developed from raw pine bark by grafting amine groups and quaternary ammonium groups onto the surface of bark particles. The results of PFOA adsorption at low concentration suggest that PG-PB has excellent removal efficiency (94.8%-99.1%, PG-PB dosage: 0.4 g/L) to PFOA in the concentration range of 10 μg/L to 2 mg/L. The PG-PB exhibited high adsorption efficiency regarding PFOA, being 456.0 mg/g at pH 3.3 and 258.0 mg/g at pH 7 with an initial concentration of 200 mg/L. The groundwater treatment reduced the total concentration of 28 PFAS from 18 000 ng/L to 9900 ng/L with 0.8 g/L of PG-PB. Desorption experiments examined 18 types of desorption solutions, and the results showed that 0.05% NaOH and a mixture of 0.05% NaOH + 20% methanol were efficient for PFOA desorption from the spent PG-PB. More than 70% (>70 mg/L in 50 mL) and 85% (>85 mg/L in 50 mL) of PFOA were recovered from the first and second desorption processes, respectively. Since high pH promotes PFOA degradation, the desorption eluents with NaOH were directly treated with a UV/sulfite system without further adjustment. The final PFOA degradation and defluorination efficiency in the desorption eluents with 0.05% NaOH + 20% methanol reached 100% and 83.1% after 24 h reaction. This study proved that the combination of adsorption/desorption and a UV/sulfite system for PFAS removal is a feasible solution for environmental remediation., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier Inc. All rights reserved.)

An in situ method for spreading iron amendments to arsenic (As)-contaminated soil has been investigated in the laboratory and field. This study tested the distribution of Fe from corroding electrodes through soil using a low-voltage direct current in a laboratory setting and validated the method in the field for As immobilisation in contaminated soil. Laboratory tests revealed that the corrosion of Fe electrodes in soil occurred in a way similar to that during the Fe electrocoagulation in water, which decreased the As concentrations in flow-through water from 150 μg L -1 to undetectable levels. Method validation over one year in the field using electric current pulses with reversing polarity revealed a decrease in As concentration in groundwater by 72-97% in five of the six groundwater wells within the experimental area. This method of introducing Fe amendments to soil can reduce the need for soil excavation upon chemical immobilisation of contaminants in soil., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 The Authors. Published by Elsevier Ltd.. All rights reserved.)

In 2009, a low-volume gravel road in Sweden was stabilised using fly ash from a local paper mill. The objective was to examine whether fly ash could be used to enhance the stability of the road and how the nearby environment would be affected. The technical and environmental properties of the road have been monitored for two, six, and eleven years. Because the construction costs are higher for ash upgrading than for conventional upgrading, knowing for how long the improved properties will remain is relevant. Strength development was studied using a falling weight deflectometer and compressive strength tests. Environmental properties were studied by chemical analysis of road samples, soil, soil pore water, and vegetation. The results showed that the ash sections had higher stiffness than the reference sections. Leaching tests of road samples showed that the mobility of potassium, sodium, chloride, and sulfate decreased with time. Trace element concentrations in soil samples, except barium, were below the Swedish guideline values for sensitive land use. Chromium, lead, and copper were as high or even higher along the reference section than along the ash section. After 11 years, the pH closest to the ash section was slightly enhanced. Concentrations of zinc and cadmium in the soil pore water were the lowest closest to the ash road, although the total concentrations in the soil were at their highest at the same distance. No toxic levels of trace elements were found in the vegetation close to the road, although a clear difference was observed between plants from the ash section and the reference section, using multivariate data analysis. The positive effects on the geotechnical road properties from ash stabilisation remained after 11 years. The environmental impacts on nearby soil and vegetation can be considered low and acceptable. This study demonstrates that the use of biofuel fly ash in infrastructure projects can contribute to the circular economy and effective use of resources because the demand for pristine materials will be reduced., (Copyright © 2022 The Authors. Published by Elsevier Ltd.. All rights reserved.)

This paper presents experimental results from the use of biosurfactants in the remediation of a soil from a smelter in Poland. In the soil, concentrations of Cu (1659.1 mg/kg) and Pb (290.8 mg/kg) exceeded the limit values. Triple batch washing was tested as a soil treatment. Three main variants were used, each starting with a different plant-derived (saponin, S; tannic acid, T) or microbial (rhamnolipids, R) biosurfactant solution in the first washing, followed by 9 different sequences using combinations of the tested biosurfactants (27 in total). The efficiency of the washing was determined based on the concentration of metal removed after each washing (C R ), the cumulative removal efficiency (E cumulative ) and metal stability (calculated as the reduced partition index, I r , based on the metal fractions from BCR sequential extraction). The type of biosurfactant sequence influenced the C R values. The variants that began with S and R had the highest average E cumulative for Cu and Pb, respectively. The E cumulative value correlated very strongly (r > 0.8) with the stability of the residual metals in the soil. The average E cumulative and stability of Cu were the highest, 87.4% and 0.40, respectively, with the S-S-S, S-S-T, S-S-R and S-R-T sequences. Lead removal and stability were the highest, 64-73% and 0.36-0.41, respectively, with the R-R-R, R-R-S, R-S-R and R-S-S sequences. Although the loss of biosurfactants was below 10% after each washing, sequential washing with biosurfactants enriched the soil with external organic carbon by an average of 27-fold (S-first variant), 24-fold (R first) or 19-fold (T first). With regard to environmental limit values, metal stability and organic carbon resources, sequential washing with different biosurfactants is a beneficial strategy for the remediation of smelter-contaminated soil with given properties.

Some of the older Swedish roads contain road tar underneath a surface layer of bituminous asphalt. This road tar, also known as tar asphalt, contains large amounts of polycyclic aromatic hydrocarbons (PAHs). There is concern about PAHs spreading from the bottom layers of these older roads to the surrounding environment, and that because of this spreading road tar asphalt should not be recycled but rather placed in landfills. However, a risk assessment of PAH spreading below roads has not yet been conducted. The first aim of this study was to assess this potential spreading of PAHs from underlying tar asphalt to the sand beneath, the soil next to the roads, as well as nearby groundwater. The second aim was to measure the bioavailability and estimate the toxicity of PAHs in all relevant media using polyoxymethylene (POM) passive samplers. Four road sections and nearby groundwater in northern Sweden were investigated, including a control road without tar asphalt. PAHs were detected in all analysed solid media at varying concentrations: in asphalt from 2.3 to 4800 mg kg -1 , in underlying sand from <1.5 to 460 mg kg -1 and in slope soil from <1.5 to 36 mg kg -1 . However, the spread of PAHs from the asphalt to roadside soil and groundwater was very limited. Groundwater at most of the road sections contained very low or non-detectable levels of PAHs (<0.08-0.53 μg L -1 , excluding one site where fuel contamination is hypothesized). The PAHs generally showed low bioavailability. Only asphalt with PAH content >1200 mg kg -1 exhibited bioavailable concentrations that exceeded threshold concentrations for serious risk. The most PAH contaminated sand and soil samples exhibited low toxicity when considering bioavailability, only in some cases exceeding chronic toxicity threshold concentrations. These results were compared with the Swedish EPA's guideline values for PAH in contaminated soil, which is shown to overpredict toxicity for these sites. Further research on the leaching and transportation processes of PAHs from subsurface tar asphalt is recommended for developing risk analysis approaches., (Copyright © 2021 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Electrochemical degradation using boron-doped diamond (BDD) electrodes has been proven to be a promising technique for the treatment of water contaminated with per- and poly-fluoroalkyl substances (PFAS). Various studies have demonstrated that the extent of PFAS degradation is influenced by the composition of samples and electrochemical conditions. This study evaluated the significance of several factors, such as the current density, initial concentration of PFAS, concentration of electrolyte, treatment time, and their interactions on the degradation of PFAS. A 2 4 factorial design was applied to determine the effects of the investigated factors on the degradation of perfluorooctanoic acid (PFOA) and generation of fluoride in spiked water. The best-performing conditions were then applied to the degradation of PFAS in wastewater samples. The results revealed that current density and time were the most important factors for PFOA degradation. In contrast, a high initial concentration of electrolyte had no significant impact on the degradation of PFOA, whereas it decreased the generation of F - . The experimental design model indicated that the treatment of spiked water under a current density higher than 14 mA cm -2 for 3-4 h could degrade PFOA with an efficiency of up to 100% and generate an F - fraction of approximately 40-50%. The observed high PFOA degradation and a low concentration of PFAS degradation products indicated that the mineralization of PFOA was effective. Under the obtained best conditions, the degradation of PFOA in wastewater samples was 44-70%. The degradation efficiency for other PFAS in these samples was 65-80% for perfluorooctane sulfonic acid (PFOS) and 42-52% for 6-2 fluorotelomer sulfonate (6-2 FTSA). The presence of high total organic carbon (TOC) and chloride contents was found to be an important factor affecting the efficiency of PFAS electrochemical degradation in wastewater samples. The current study indicates that the tested method can effectively degrade PFAS in both water and wastewater and suggests that increasing the treatment time is needed to account for the presence of other oxidizable matrices., (Copyright © 2021 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Cadmium, Cu, Ni, Pb, and Zn removal via soil flushing with tannic acid (TA) as a plant biosurfactant was studied. The soil was treated for 30 h in a column reactor at a constant TA concentration and pH (3%, pH 4) and at variable TA flow rates (0.5 mL/min or 1 mL/min). In the soil leachates, pH, electrical conductivity (EC), total dissolved organic carbon, and metal concentrations were monitored. Before and after flushing, soil pH, EC, organic matter content, and cation exchange capacity (CEC) were determined. To analyze the organic matter composition, pyrolysis as well as thermally assisted hydrolysis and methylation coupled with gas chromatography-mass spectrometry were used. Metal fractionation in unflushed and flushed soil was analyzed using a modified sequential extraction method. The data on cumulative metal removal were analyzed using OriginPro 8.0 software (OriginLab Corporation, Northampton, MA, USA) and were fitted to 4-parameter logistic sigmoidal model. It was found that flushing time had a stronger influence on metal removal than flow rate. The overall efficiency of metal removal (expressed as the ratio between flushed metal concentration and total metal concentration in soil) at the higher flow rate decreased in this order: Cd (86%) > Ni (44%) > Cu (29%) ≈ Zn (26%) > Pb (15%). Metals were removed from the exchangeable fraction and redistributed into the reducible fraction. After flushing, the soil had a lower pH, EC, and CEC; a higher organic matter content; the composition of the organic matter had changed (incorporation of TA structures). Our results prove that soil flushing with TA is a promising approach to decrease metal concentration in soil and to facilitate carbon sequestration in soil.

This study aimed at elucidating the long-term efficiency of soil remediation where chemical stabilization of arsenic (As) contaminated soil using zerovalent iron (Fe) amendments was applied. A combination of chemical extraction and extended X-Ray absorption fine structure (EXAFS) spectroscopy technique was applied on soils collected from five laboratory and field experiments in Sweden and France. All soils were treated with 1 wt% of zerovalent Fe grit 2-15 years prior to the sampling. The results indicate that all studied soils, despite the elapsed time since their amendment with Fe grit, had substantial amounts of ferrihydrite and/or lepidocrocite. These metastable and the most reactive Fe (oxyhydr)oxides (mainly ferrihydrite) were still present in substantial amounts even in the soil that was treated 15 years prior to the sampling and contributed most to the As immobilisation in the amended soils. This increases confidence in the long-term efficiency of As immobilisation using zerovalent Fe amendments. Both applied methods, sequential extraction and EXAFS, were in line for most of the samples in terms of their ability to highlight As immobilisation by poorly crystalline Fe phases., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Poly- and perfluoroalkyl substances (PFASs) are synthetic chemicals, which are introduced to the environment through anthropogenic activities. Aqueous film forming foam used in firefighting, wastewater effluent, landfill leachate, and biosolids are major sources of PFAS input to soil and groundwater. Remediation of PFAS contaminated solid and aqueous media is challenging, which is attributed to the chemical and thermal stability of PFAS and the complexity of PFAS mixtures. In this review, remediation of PFAS contaminated soils through manipulation of their bioavailability and destruction is presented. While the mobilizing amendments (e.g., surfactants) enhance the mobility and bioavailability of PFAS, the immobilizing amendments (e.g., activated carbon) decrease their bioavailability and mobility. Mobilizing amendments can be applied to facilitate the removal of PFAS though soil washing, phytoremediation, and complete destruction through thermal and chemical redox reactions. Immobilizing amendments are likely to reduce the transfer of PFAS to food chain through plant and biota (e.g., earthworm) uptake, and leaching to potable water sources. Future studies should focus on quantifying the potential leaching of the mobilized PFAS in the absence of removal by plant and biota uptake or soil washing, and regular monitoring of the long-term stability of the immobilized PFAS., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Contaminated water with multiple contaminants, including As, Cr, Cu and Zn, was treated with a sorbent prepared by coating peat with Fe oxides. Because As has a relatively little explored market, the regeneration of the spent sorbent was not feasible. Meanwhile, the disposal of As wastes in landfills can cause landfill leachate treatment problems. Under the reducing conditions prevailing at landfills, As(V) is reduced to As(III), which is a toxic and more mobile form. In this study, incineration was explored as a management option to treat the spent sorbent that was loaded with As, Cr, Cu and Zn. The first objective of this study was to evaluate the leaching of these metal(loid)s from the ashes and compare it with the leaching from the spent sorbents before incineration. The second objective was to evaluate the leaching behaviour when the spent sorbent was co-incinerated with a Ca-rich additive (lime). To achieve these objectives, the obtained ashes were subjected to leaching tests, sequential extraction, and X-ray diffraction analyses. After the incineration, the ash content ranged from 9 to 19% of the initial mass of the spent sorbents. The leaching of As, Cu and Zn decreased compared with that from the spent sorbents before the thermal treatment because of the high incineration temperatures and/or co-incineration with lime. However, the leaching of Cr increased, which would hinder the disposal of the obtained ashes in a landfill because the limit value for disposal at a landfill for hazardous wastes was exceeded by 50 times. However, co-incineration with 10 wt% lime significantly decreased the leaching of Cr as a result of the formation of water-insoluble Ca-Cr compounds.

The aim of this study was to compare the immobilisation of metal(loid)s in two differently contaminated soils using micro zerovalent iron (ZVI) and nano zerovalent iron (nZVI) particles. Chromated copper arsenate-contaminated soil contained high amounts of As, Cu, Cr, and Zn, whereas mining-contaminated soil contained high amounts of As, Cu, and Pb. Contaminated soils were amended using 2% ZVI and nZVI. As determined by the leaching procedures, nZVI was more efficient in immobilising all the studied metal(loid)s in the soils compared to ZVI. The greatest immobilisation was achieved for As in both soils. The long-term stability of immobilised metal(loid)s was studied in mining-contaminated soil by performing thermal oxidation (ageing). In the ZVI and nZVI-treated soils, high retention results were achieved for As and Cu, whereas in the ZVI and nZVI-treated soils, significant desorption of Pb was observed. The results also showed that retention of metal(loid)s over a long period of time could be more effective in soils treated with ZVI, as the crystallisation of Fe in ZVI-treated soil was to a lesser extent compared to the crystallisation of Fe in nZVI-treated soil., Competing Interests: Declaration of competing interest The study was financially supported by Luleå University of Technology (Sweden) and Vilnius Gediminas Technical University (Lithuania)., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

Hydrothermal carbonisation (HTC) is a wet and relatively low-temperature process where, under autogenous pressures, biomass undergoes a chain of reactions leading to the defragmentation of organic matter. As well as its other uses (e.g. for producing low-cost carbon-based nano-compounds), HTC is utilised for the treatment of wet wastes, such as manure and biosludge. This study aimed to determine if hydrothermal carbonisation is a feasible treatment method for spent sorbents that are highly enriched with arsenic, chromium, copper, and zinc. The chemical properties of hydrochar and process liquid were evaluated after HTC treatment, where peat-based spent sorbents were carbonised at 230 °C for 3 h. Analysis of Fourier transform-infrared spectra revealed that during HTC, the oxygenated bonds of ethers, esters, and carboxylic groups were cleaved, and low-molecular-weight organic fragments were dissolved in the process liquid. A large fraction of arsenic (up to 62%), copper (up to 25%), and zinc (up to 36%) were transferred from the solids into the process water. Leaching of these elements from the hydrochars increased significantly in comparison with the spent sorbents.

This study firstly aimed to investigate the potential of simultaneous metal (loid) removal from metal (oid) solution through adsorption on iron-peat, where the sorbent was made from peat and Fe by-products. Up-flow columns filled with the prepared sorbent were used to treat water contaminated with As, Cu, Cr, and Zn. Peat effectively adsorbed Cr, Cu, and Zn, whereas approximately 50% of inlet As was detected in the eluent. Iron-sand was effective only for adsorbing As, but Cr, Cu, and Zn were poorly adsorbed. Only iron-peat showed the simultaneous removal of all tested metal (loid)s. Metal (loid) leaching from the spent sorbent at reducing conditions as means to assess the behaviour of the spent sorbent if landfilled was also evaluated. For this purpose, a standardised batch leaching test and leaching experiment at reducing conditions were conducted using the spent sorbent. It was found that oxidising conditions, which prevailed during the standardised batch leaching test, could have led to an underestimation of redox-sensitive As leaching. Substantially higher amounts of As were leached out from the spent sorbents at reducing atmosphere compared with oxidising one. Furthermore, reducing environment caused As(V) to be reduced into the more-toxic As (III).

This study aimed at combining iron and peat to produce a sorbent suitable for a simultaneous removal of cations and anions from a solution. Peat powder, an industrial residue, was coated with iron by immersing peat into iron salt solutions. The adsorption efficiency of the newly produced sorbent towards As, Cr, Cu and Zn was tested by means of batch adsorption experiments at a constant pH value of 5. Coating of Fe on peat significantly increased the adsorption of As (from <5% to 80%) and Cr (from <3% to 25%) in comparison to uncoated peat. Removal of cations on coated peat slightly decreased (by 10-15%), yet remained within acceptable range. Electron Microscopy combined with X-Ray Energy Dispersive Spectroscopy revealed that iron coating on the peat was rather homogenous and As and Cr were abundantly adsorbed on the surface. By contrast, Cu and Zn displayed a sparing distribution on the surface of the iron coated peat. These results indicate that iron-peat simultaneously target sufficient amounts of both cations and anions and can be used for a one-step treatment of contaminated groundwater., (Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The leaching behaviour of a road construction with fayalitic copper slag, recycled concrete and crushed rock as sub-base materials was monitored over ten years. All studied materials used in the road construction, including crushed rock, contained concentrations of several elements exceeding the guideline values recommended by the Swedish EPA for total element concentrations for waste materials used in constructions. Despite that, leaching from the road construction under field conditions in general was relatively low. The leachates from the recycled materials contained higher concentrations of several constituents than the leachates from the reference section with crushed rock. The leaching of the elements of interest (Cr, Mo, Ni, Zn) reached peak concentrations during the second and fourth (Cu) years and decreased over the observation period to levels below the Swedish recommended values. Carbonation of the concrete aggregates caused a substantial but short-term increase in the leaching of oxyanions such as chromate. The environmental risks related to element leaching are highest at the beginning of the road life. Ageing of materials or pre-treatment through leaching is needed prior to their use in construction to avoid peak concentrations. Also, the design of road constructions should be adjusted so that recycled materials are covered with low-permeability covers, which would minimize the exposure to atmospheric precipitation and weathering., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Gentle remediation options (GRO), i.e. in situ stabilisation, (aided) phytoextraction and (aided) phytostabilisation, were implemented at ten European sites contaminated with trace elements (TE) from various anthropogenic sources: mining, atmospheric fallout, landfill leachates, wood preservatives, dredged-sediments, and dumped wastes. To assess the performance of the GRO options, topsoil was collected from each field trial, potted, and cultivated with lettuce (Lactuca sativa L.) for 48days. Shoot dry weight (DW) yield, photosynthesis efficiency and major element and TE concentrations in the soil pore water and lettuce shoots were measured. GRO implementation had a limited effect on TE concentrations in the soil pore water, although use of multivariate Co-inertia Analysis revealed a clear amelioration effect in phytomanaged soils. Phytomanagement increased shoot DW yield at all industrial and mine sites, whereas in agricultural soils improvements were produced in one out of five sites. Photosynthesis efficiency was less sensitive than changes in shoot biomass and did not discriminate changes in soil conditions. Based on lettuce shoot DW yield, compost amendment followed by phytoextraction yielded better results than phytostabilisation; moreover shoot ionome data proved that, depending on initial soil conditions, recurrent compost application may be required to maintain crop production with common shoot nutrient concentrations., (Copyright © 2017 Elsevier B.V. All rights reserved.)