Search

Interactive sensors are an important component of robotic systems but often require manual replacement due to wear and tear. Automating this process can enhance system autonomy and facilitate long-term deployment. We developed an autonomous sensor exchange and calibration system for an agriculture crop monitoring robot that inserts a nitrate sensor into cornstalks. A novel gripper and replacement mechanism, featuring a reliable funneling design, were developed to enable efficient and reliable sensor exchanges. To maintain consistent nitrate sensor measurement, an on-board sensor calibration station was integrated to provide in-field sensor cleaning and calibration. The system was deployed at the Ames Curtis Farm in June 2024, where it successfully inserted nitrate sensors with high accuracy into 30 cornstalks with a 77$\%$ success rate.

A promising approach to detect high-energy tau neutrinos is through the measurement of impulsive radio emission from horizontal air showers initiated in the Earth's atmosphere. Observations at frequencies between 30 and 80 MHz seem particularly promising -- if high-gain antennas focused at the horizon and blocking out as much as possible of the noisy sky are employed. Due to the large wavelengths, however, designing an antenna with the required properties is highly non-trivial at such low frequencies. In this article, we explore suitable antenna designs that provide the desired high gain, possess a smooth beam, are insensitive to ground conditions, are easily impedance-matched over the wide band, and are mechanically simple for deployment in large numbers in inaccessible terrain. In particular, we consider the "rhombus" antenna design for both horizontally and vertically polarized radiation a very attractive option for tau neutrino detection efforts in the atmosphere with the radio technique., Comment: 15 pages, to be submitted to JINST

Model-based planners and controllers are commonly used to solve complex manipulation problems as they can efficiently optimize diverse objectives and generalize to long horizon tasks. However, they are limited by the fidelity of their model which oftentimes leads to failures during deployment. To enable a robot to recover from such failures, we propose to use hierarchical reinforcement learning to learn a separate recovery policy. The recovery policy is triggered when a failure is detected based on sensory observations and seeks to take the robot to a state from which it can complete the task using the nominal model-based controllers. Our approach, called RecoveryChaining, uses a hybrid action space, where the model-based controllers are provided as additional \emph{nominal} options which allows the recovery policy to decide how to recover, when to switch to a nominal controller and which controller to switch to even with \emph{sparse rewards}. We evaluate our approach in three multi-step manipulation tasks with sparse rewards, where it learns significantly more robust recovery policies than those learned by baselines. Finally, we successfully transfer recovery policies learned in simulation to a physical robot to demonstrate the feasibility of sim-to-real transfer with our method., Comment: 8 pages, 9 figures

This is an index of the contributions by the Giant Radio Array for Neutrino Detection (GRAND) Collaboration to the 10th International Workshop on Acoustic and Radio EeV Neutrino Detection Activities (ARENA 2024, University of Chicago, June 11-14, 2024). The contributions include an overview of GRAND in its present and future incarnations, methods of radio-detection that are being developed for them, and ongoing joint work between the GRAND and BEACON experiments., Comment: Note: To access the list of contributions, please follow the "HTML" link that can be found on the arXiv page

Neutrinos at ultrahigh energies can originate both from interactions of cosmic rays at their acceleration sites and through cosmic-ray interactions as they propagate through the universe. These neutrinos are expected to have a low flux which drives the need for instruments with large effective areas. Radio observations of the inclined air showers induced by tau neutrino interactions in rock can achieve this, because radio waves can propagate essentially unattenuated through the hundreds of kilometers of atmosphere. Proposed arrays for radio detection of tau neutrinos focus on either arrays of inexpensive receivers distributed over a large area, the GRAND concept, or compact phased arrays on elevated mountains, the BEACON concept, to build up a large detector area with a low trigger threshold. We present a concept that combines the advantages of these two approaches with a trigger driven by phased arrays at a moderate altitude (1 km) and sparse, high-gain outrigger receivers for reconstruction and background rejection. We show that this design has enhanced sensitivity at 100 PeV over the two prior designs with fewer required antennas and discuss the need for optimized antenna designs., Comment: ARENA2024 Conference Proceeding PoS(ARENA2024)058

Dexterous robotic manipulation remains a challenging domain due to its strict demands for precision and robustness on both hardware and software. While dexterous robotic hands have demonstrated remarkable capabilities in complex tasks, efficiently learning adaptive control policies for hands still presents a significant hurdle given the high dimensionalities of hands and tasks. To bridge this gap, we propose Tilde, an imitation learning-based in-hand manipulation system on a dexterous DeltaHand. It leverages 1) a low-cost, configurable, simple-to-control, soft dexterous robotic hand, DeltaHand, 2) a user-friendly, precise, real-time teleoperation interface, TeleHand, and 3) an efficient and generalizable imitation learning approach with diffusion policies. Our proposed TeleHand has a kinematic twin design to the DeltaHand that enables precise one-to-one joint control of the DeltaHand during teleoperation. This facilitates efficient high-quality data collection of human demonstrations in the real world. To evaluate the effectiveness of our system, we demonstrate the fully autonomous closed-loop deployment of diffusion policies learned from demonstrations across seven dexterous manipulation tasks with an average 90% success rate.

Optimizing robotic action parameters is a significant challenge for manipulation tasks that demand high levels of precision and generalization. Using a model-based approach, the robot must quickly reason about the outcomes of different actions using a predictive model to find a set of parameters that will have the desired effect. The model may need to capture the behaviors of rigid and deformable objects, as well as objects of various shapes and sizes. Predictive models often need to trade-off speed for prediction accuracy and generalization. This paper proposes a framework that leverages the strengths of multiple predictive models, including analytical, learned, and simulation-based models, to enhance the efficiency and accuracy of action parameter optimization. Our approach uses Model Deviation Estimators (MDEs) to determine the most suitable predictive model for any given state-action parameters, allowing the robot to select models to make fast and precise predictions. We extend the MDE framework by not only learning sim-to-real MDEs, but also sim-to-sim MDEs. Our experiments show that these sim-to-sim MDEs provide significantly faster parameter optimization as well as a basis for efficiently learning sim-to-real MDEs through finetuning. The ease of collecting sim-to-sim training data also allows the robot to learn MDEs based directly on visual inputs and local material properties.

This paper presents a modular, reconfigurable robot platform for robot manipulation in agriculture. While robot manipulation promises great advancements in automating challenging, complex tasks that are currently best left to humans, it is also an expensive capital investment for researchers and users because it demands significantly varying robot configurations depending on the task. Modular robots provide a way to obtain multiple configurations and reduce costs by enabling incremental acquisition of only the necessary modules. The robot we present, Hefty, is designed to be modular and reconfigurable. It is designed for both researchers and end-users as a means to improve technology transfer from research to real-world application. This paper provides a detailed design and integration process, outlining the critical design decisions that enable modularity in the mobility of the robot as well as its sensor payload, power systems, computing, and fixture mounting. We demonstrate the utility of the robot by presenting five configurations used in multiple real-world agricultural robotics applications., Comment: 8 pages, 11 figures

Measure structured deformations are introduced to present a unified theory of deformations of continua. The energy associated with a measure structured deformation is defined via relaxation departing either from energies associated with classical deformations or from energies associated with structured deformations. A concise integral representation of the energy functional is provided both in the unconstrained case and under Dirichlet conditions on a part of the boundary.

Leveraging sensing modalities across diverse spatial and temporal resolutions can improve performance of robotic manipulation tasks. Multi-spatial resolution sensing provides hierarchical information captured at different spatial scales and enables both coarse and precise motions. Simultaneously multi-temporal resolution sensing enables the agent to exhibit high reactivity and real-time control. In this work, we propose a framework, MResT (Multi-Resolution Transformer), for learning generalizable language-conditioned multi-task policies that utilize sensing at different spatial and temporal resolutions using networks of varying capacities to effectively perform real time control of precise and reactive tasks. We leverage off-the-shelf pretrained vision-language models to operate on low-frequency global features along with small non-pretrained models to adapt to high frequency local feedback. Through extensive experiments in 3 domains (coarse, precise and dynamic manipulation tasks), we show that our approach significantly improves (2X on average) over recent multi-task baselines. Further, our approach generalizes well to visual and geometric variations in target objects and to varying interaction forces., Comment: CoRL'23, Project website: http://tinyurl.com/multi-res-realtime-control

When planning with an inaccurate dynamics model, a practical strategy is to restrict planning to regions of state-action space where the model is accurate: also known as a \textit{model precondition}. Empirical real-world trajectory data is valuable for defining data-driven model preconditions regardless of the model form (analytical, simulator, learned, etc...). However, real-world data is often expensive and dangerous to collect. In order to achieve data efficiency, this paper presents an algorithm for actively selecting trajectories to learn a model precondition for an inaccurate pre-specified dynamics model. Our proposed techniques address challenges arising from the sequential nature of trajectories, and potential benefit of prioritizing task-relevant data. The experimental analysis shows how algorithmic properties affect performance in three planning scenarios: icy gridworld, simulated plant watering, and real-world plant watering. Results demonstrate an improvement of approximately 80% after only four real-world trajectories when using our proposed techniques., Comment: Accepted to International Conference on Robotics and Automation 2024. Will be presented May 2024

There is growing interest in automating agricultural tasks that require intricate and precise interaction with specialty crops, such as trees and vines. However, developing robotic solutions for crop manipulation remains a difficult challenge due to complexities involved in modeling their deformable behavior. In this study, we present a framework for learning the deformation behavior of tree-like crops under contact interaction. Our proposed method involves encoding the state of a spring-damper modeled tree crop as a graph. This representation allows us to employ graph networks to learn both a forward model for predicting resulting deformations, and a contact policy for inferring actions to manipulate tree crops. We conduct a comprehensive set of experiments in a simulated environment and demonstrate generalizability of our method on previously unseen trees. Videos can be found on the project website: https://kantor-lab.github.io/tree_gnn, Comment: 7 pages, 10 figures

We present a contact-based phenotyping robot platform that can autonomously insert nitrate sensors into cornstalks to proactively monitor macronutrient levels in crops. This task is challenging because inserting such sensors requires sub-centimeter precision in an environment which contains high levels of clutter, lighting variation, and occlusion. To address these challenges, we develop a robust perception-action pipeline to detect and grasp stalks, and create a custom robot gripper which mechanically aligns the sensor before inserting it into the stalk. Through experimental validation on 48 unique stalks in a cornfield in Iowa, we demonstrate our platform's capability of detecting a stalk with 94% success, grasping a stalk with 90% success, and inserting a sensor with 60% success. In addition to developing an autonomous phenotyping research platform, we share key challenges and insights obtained from deployment in the field. Our research platform is open-sourced, with additional information available at https://kantor-lab.github.io/cornbot.

Robots need to estimate the material and dynamic properties of objects from observations in order to simulate them accurately. We present a Bayesian optimization approach to identifying the material property parameters of objects based on a set of observations. Our focus is on estimating these properties based on observations of scenes with different sets of interacting objects. We propose an approach that exploits the structure of the reward function by modeling the reward for each observation separately and using only the parameters of the objects in that scene as inputs. The resulting lower-dimensional models generalize better over the parameter space, which in turn results in a faster optimization. To speed up the optimization process further, and reduce the number of simulation runs needed to find good parameter values, we also propose partial evaluations of the reward function, wherein the selected parameters are only evaluated on a subset of real world evaluations. The approach was successfully evaluated on a set of scenes with a wide range of object interactions, and we showed that our method can effectively perform incremental learning without resetting the rewards of the gathered observations.

Large, high-capacity models trained on diverse datasets have shown remarkable successes on efficiently tackling downstream applications. In domains from NLP to Computer Vision, this has led to a consolidation of pretrained models, with general pretrained backbones serving as a starting point for many applications. Can such a consolidation happen in robotics? Conventionally, robotic learning methods train a separate model for every application, every robot, and even every environment. Can we instead train generalist X-robot policy that can be adapted efficiently to new robots, tasks, and environments? In this paper, we provide datasets in standardized data formats and models to make it possible to explore this possibility in the context of robotic manipulation, alongside experimental results that provide an example of effective X-robot policies. We assemble a dataset from 22 different robots collected through a collaboration between 21 institutions, demonstrating 527 skills (160266 tasks). We show that a high-capacity model trained on this data, which we call RT-X, exhibits positive transfer and improves the capabilities of multiple robots by leveraging experience from other platforms. More details can be found on the project website https://robotics-transformer-x.github.io., Comment: Project website: https://robotics-transformer-x.github.io

Dexterous robotic manipulation in unstructured environments can aid in everyday tasks such as cleaning and caretaking. Anthropomorphic robotic hands are highly dexterous and theoretically well-suited for working in human domains, but their complex designs and dynamics often make them difficult to control. By contrast, parallel-jaw grippers are easy to control and are used extensively in industrial applications, but they lack the dexterity for various kinds of grasps and in-hand manipulations. In this work, we present DELTAHANDS, a synergistic dexterous hand framework with Delta robots. The DELTAHANDS are soft, easy to reconfigure, simple to manufacture with low-cost off-the-shelf materials, and possess high degrees of freedom that can be easily controlled. DELTAHANDS' dexterity can be adjusted for different applications by leveraging actuation synergies, which can further reduce the control complexity, overall cost, and energy consumption. We characterize the Delta robots' kinematics accuracy, force profiles, and workspace range to assist with hand design. Finally, we evaluate the versatility of DELTAHANDS by grasping a diverse set of objects and by using teleoperation to complete three dexterous manipulation tasks: cloth folding, cap opening, and cable arrangement. We open-source our hand framework at https://sites.google.com/view/deltahands/.

We prove a quantitative convergence result of the nonlocal Allen--Cahn equation to volume-preserving mean curvature flow. The proof uses gradient flow calibrations and the relative entropy method, which has been used in the recent literature to prove weak-strong uniqueness results for mean curvature flow and convergence of the Allen--Cahn equation. A crucial difference in this work is a new notion of gradient flow calibrations. We add a tangential component to the velocity field in order to prove the Gronwall estimate for the relative energy. This allows us to derive the optimal convergence rate without having to show the closeness of the Lagrange-multipliers.

We present a new example for the Lavrentiev phenomenon in context of nonlinear elasticity, caused by an interplay of the elastic energy's resistance to infinite compression and the Ciarlet-Ne\v{c}as condition, a constraint preventing global interpenetration of matter on sets of full measure.

Planning robot dexterity is challenging due to the non-smoothness introduced by contacts, intricate fine motions, and ever-changing scenarios. We present a hierarchical planning framework for dexterous robotic manipulation (HiDex). This framework explores in-hand and extrinsic dexterity by leveraging contacts. It generates rigid-body motions and complex contact sequences. Our framework is based on Monte-Carlo Tree Search and has three levels: 1) planning object motions and environment contact modes; 2) planning robot contacts; 3) path evaluation and control optimization. This framework offers two main advantages. First, it allows efficient global reasoning over high-dimensional complex space created by contacts. It solves a diverse set of manipulation tasks that require dexterity, both intrinsic (using the fingers) and extrinsic (also using the environment), mostly in seconds. Second, our framework allows the incorporation of expert knowledge and customizable setups in task mechanics and models. It requires minor modifications to accommodate different scenarios and robots. Hence, it provides a flexible and generalizable solution for various manipulation tasks. As examples, we analyze the results on 7 hand configurations and 15 scenarios. We demonstrate 8 tasks on two robot platforms., Comment: The IEEE Robotics and Automation Letters

We analyze a term penalizing surface self-penetration, as a soft constraint for models of hyperelastic materials to approximate the Ciarlet-Ne\v{c}as condition (almost everywhere global invertibility of deformations). For a linear elastic energy subject to an additional local invertibility constraint, we prove that the penalized elastic functionals converge to the original functional subject to the Ciarlet-Ne\v{c}as condition. The approach also works for nonlinear models of non-simple materials including a suitable higher order term in the elastic energy, without artificial local constraints. Numerical experiments illustrate our results for a self-contact problem in 3d., Comment: 40 pages, 4 figures. Slightly expanded version

We derive a uniqueness and stability principle for surface diffusion before the onset of singularities. The perturbations, however, are allowed to undergo topological changes. The main ingredient is a relative energy inequality, which in turn relies on the explicit construction of (volume-preserving) gradient flow calibrations. The proof applies to stationary solutions in any dimension and to general smooth solutions in two dimensions.