Search

The livestock industry plays a significant role in the economic well-being of many parts of the world with a host of environmental challenges. Key amongst them is the management of gaseous emissions emitted from livestock manure. Mitigation of gaseous emissions from livestock operations such as odor, odorous volatile organic compounds (VOCs), ammonia (NH 3 ), hydrogen sulfide (H 2 S), and greenhouse gases (GHGs) have been of research interest for the last couple of decades. Biochar, a low-cost-value byproduct of biorenewable energy and thermochemical waste processing compared with syngas and bio-oil, has been actively researched as a potential surficial treatment of manure and emissions from stored or co-composted manure. Yet, the efficacy of biochar treatment differs, partly because biochar properties vary with feedstock and thermochemical processing conditions. To date, the results from laboratory-scale trials are encouraging, but a more focused effort is needed to bring this technology closer to farm-scale applications. Therefore, this review aims to summarize and highlight current research related to mitigating gaseous emissions from manure treated with biochar. Various types of biochar, and modes of biochar applications, e.g., manure additives and co-composting, dosage, and timing, are discussed in the context of targeted gas emissions mitigation. Gaps in knowledge remain, including demonstrated larger-scale mitigation performance and verifiable technoecomics. Standardization and certification of biochar properties suitable for specific environmental management applications are recommended. The potential synergy between mitigating emissions, improving manure quality, carbon, and nitrogen cycling in animal and crop production agriculture is found. Biochar can be a comprehensive solution to gaseous emissions while also upgrading manure as a high-quality additive that could improve the sustainability of animal and crop production systems., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Published by Elsevier Ltd.)

Atmospheric methane (CH 4 ) acts as a key contributor to global warming. As CH 4 is a short-lived climate forcer (12 years atmospheric lifespan), its mitigation represents the most promising means to address climate change in the short term. Enteric CH 4 (the biosynthesized CH 4 from the rumen of ruminants) represents 5.1% of total global greenhouse gas (GHG) emissions, 23% of emissions from agriculture, and 27.2% of global CH 4 emissions. Therefore, it is imperative to investigate methanogenesis inhibitors and their underlying modes of action. We hereby elucidate the detailed biophysical and thermodynamic interplay between anti-methanogenic molecules and cofactor F 430 of methyl coenzyme M reductase and interpret the stoichiometric ratios and binding affinities of sixteen inhibitor molecules. We leverage this as prior in a graph neural network to first functionally cluster these sixteen known inhibitors among ~54,000 bovine metabolites. We subsequently demonstrate a protocol to identify precursors to and putative inhibitors for methanogenesis, based on Tanimoto chemical similarity and membrane permeability predictions. This work lays the foundation for computational and de novo design of inhibitor molecules that retain/ reject one or more biochemical properties of known inhibitors discussed in this study.

Recently, research has investigated the role of the ruminant native microbiome, and the role microbes play in methane (CH4) production and mitigation. However, the variation across microbiome studies makes implementing impactful strategies difficult. The first objective of this study is to identify, summarize, compile, and discuss the current literature on CH4 mitigation strategies and how they interact with the native ruminant microbiome. The second objective is to perform a meta-analysis on the identified16S rRNA sequencing data. A literature search using Web of Science, Scopus, AGRIS, and Google Scholar will be implemented. Eligible criteria will be defined using PICO (population, intervention, comparator, and outcomes) elements. Two independent reviewers will be utilized for both the literature search and data compilation. Risk of bias will be assessed using the Cochrane Risk Bias 2.0 tool. Publicly available 16S rRNA amplicon gene sequencing data will be downloaded from NCBI Sequence Read Archive, European Nucleotide Archive or similar database using appropriate extraction methods. Data processing will be performed using QIIME2 following a standardized protocol. Meta-analyses will be performed on both alpha and beta diversity as well as taxonomic analyses. Alpha diversity metrics will be tested using a Kruskal-Wallis test with a Benjamini-Hochberg multiple testing correction. Beta diversity will be statistically tested using PERMANOVA testing with multiple test corrections. Hedge's g standardized mean difference statistic will be used to calculate fixed and random effects model estimates using a 95% confidence interval. Heterogeneity between studies will be assessed using the I2 statistic. Potential publication bias will be further assessed using Begg's correlation test and Egger's regression test. The GRADE approach will be used to assess the certainty of evidence. The following protocol will be used to guide future research and meta-analyses for investigating CH4 mitigation strategies and ruminant microbial ecology. The future work could be used to enhance livestock management techniques for GHG control. This protocol is registered in Open Science Framework (https://osf.io/vt56c) and available in the Systematic Reviews for Animals and Food (https://www.syreaf.org/contact)., Competing Interests: The authors have declared that no competing interests exist., (Copyright: This is an open access article, free of all copyright, and may be freely reproduced, distributed, transmitted, modified, built upon, or otherwise used by anyone for any lawful purpose. The work is made available under the Creative Commons CC0 public domain dedication.)

A critical prelude to any community odor assessment should be the prioritization of specific chemical odorants that are most responsible for targeted downwind odors. Unfortunately, and historically, this is a step that has often been bypassed or overlooked. However, correct understanding of the specific impactful volatile organic compounds (VOCs) can inform the follow-on sampling, analytical, and remediation strategies that are most appropriate and efficient, based upon the chemistry behind the issue. With this understanding, the techniques and sampling strategies presented herein should be viewed as a qualitative prelude rather than an addendum to a follow-up routine, automated downwind odor monitoring. Downwind odor characteristics can vary depending upon the size of the upwind source, interim topography, and wind conditions. At one extreme, the downwind odor plume from a relatively large source located on a flat open plain and under stable, near-straight line wind conditions can be rather broad, sustained, and predictable. In contrast, the plume from a small point source (e.g., a roof vent stack) located on irregular topography and under rapidly shifting wind conditions can be intermittent and fleeting ("spikes" or "bursts"). These transient odor events can be surprisingly intense and offensive, despite their fleeting occurrence and perception. This work reports on improving and optimizing an environmental sampling strategy for odorant prioritization from such transient downwind odor conditions. This optimization addresses the challenges of (1) sampling of transient odor "spikes" and (2) prioritizing odors/odorants from multiple, closely colocated point sources under transient event conditions. Prioritizing is defined as identifying the key impactful odorants downwind. Grab air sampling protocol refinement has emerged from actual community environmental odor assessment projects. The challenge of assessing transient odor events has been mitigated by utilizing (a) rapid, odor-cued whole-air grab sampling (i.e., activated by and synchronous with the perceived sensory spikes) into metalized fluorinated ethylene polymer (m-FEP) gas sampling bags; (b) immediate transfer from bags onto solid-phase microextraction (SPME) fibers or sorbent tubes; and (c) maintaining refrigerated storage and shipment conditions between field collection and in-laboratory analysis. Results demonstrated approximately 11-fold increases in target odorant yields for 900 mL air sample capture on sorbent tube transfers from 2 to 3 s "burst" odor event bag captures compared to equivalent direct collections (with sorbent tubes) at the same downwind receptor location but during perceived (stable) odor "lull" periods. An application targeting general odor sampling and point-source differentiation utilizing tracer gases is also presented., Competing Interests: The authors declare the following competing financial interest(s): Three commercial entities are represented among the collaborative team (Don Wright & Associates, LLC, The Epsilon Company, LLC, and Volatile Analysis Corporation). The funders (USDA-SBIR Phase II, Iowa Agriculture and Home Economics Experiment Station) had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results., (© 2024 The Authors. Published by American Chemical Society.)

To date, only a few studies focused on the carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker's occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after- 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to 'CO sinks'. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and >115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively., Competing Interests: The authors have declared that no competing interests exist., (Copyright: © 2024 Sobieraj et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

Indoor air, especially with suspended particulate matter (PM), can be a carrier of airborne infectious pathogens. Without sufficient ventilation, airborne infectious diseases can be transmitted from one person to another. Indoor air quality (IAQ) significantly impacts people's daily lives as people spend 90% of their time indoors. An industrial-grade air cleaner prototype (filtration + ultraviolet light) was previously upgraded to clean indoor air to improve IAQ on two metrics: particulate matter (PM) and viable airborne bacteria. Previous experiments were conducted to test its removal efficiency on PM and airborne bacteria between the inlet and treated air. However, the longer-term improvement on IAQ would be more informative. Therefore, this research focused on quantifying longer-term improvement in a testing environment (poultry facility) loaded with high and variable PM and airborne bacteria concentrations. A 25-day experiment was conducted to treat indoor air using an air cleaner prototype with intermittent ON and OFF days in which PM and viable airborne bacteria were measured to quantify the treatment effect. The results showed an average of 55% reduction of total suspended particulate (TSP) concentration between OFF days (110 μg/m 3 ) and ON days (49 μg/m 3 ). An average of 47% reduction of total airborne viable bacteria concentrations was achieved between OFF days (∼3200 CFU/m 3 ) and ON days (∼2000 CFU/m 3 ). A cross-validation (CV) model was established to predict PM concentrations with five input variables, including the status of the air cleaner, time (h), ambient temperature, indoor relative humidity, and day of the week to help simulate the air-cleaning effect of this prototype. The model can approximately predict the air quality trend, and future improvements may be made to improve its accuracy., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests:Jacek Koziel reports financial support was provided by Kryton Engineered Metals Inc. and the Center for Industrial Research and Service (CIRAS) at Iowa State University., (Published by Elsevier Ltd.)

Numerous studies have investigated effects of long-term manure application on total phosphorus (P) and inorganic P (P i ), but few have evaluated soil organic P (P o ). Little is known about crop management effects on P o in soils with varying minerology. In this study, sequential fractionation was used to characterize specific P forms after 25 years of broiler litter (BL) or ammonium nitrate (Con) applications to an Alabama Hartsells soil. Crops (corn [Zea mays L.], soybean [Glycine Willd.], and corn or soybean with a wheat [Triticum aestivum L.] cover crop) were under conventional tillage (CT) or no-tillage (NT). Regardless of crop, tillage, or fertilizer type, the proportion of extractable P i was relatively stable at 21%-49% at 0-5 cm and 25%-45% at 5-10 cm. Extractable P i ranged from 0.69 to 2.4 mg g -1 . BL increased total extractable P i (p ≤ 0.001) at 0-5 cm and 5-10 cm. Total extractable P was influenced at 0-5 cm (p ≤ 0.006) by both tillage and fertilization type, but not at 5-10 cm or at either depth in soybean plots. Long-term BL application increased total extractable soil P at 0-5 cm. In corn systems, CT did not reduce P loading to topsoil or result in P leaching to lower soil depths, compared to NT. Soybean and soybean-wheat reduced P loading in BL plots, compared to corn and corn-wheat. Soil P o was classed in the order of monoesters > phytate and polyphosphates, where most was extractable with NaOH. BL increased extractable P o in all fractions. Care should be taken when applying BL to highly weathered soils to avoid legacy P o accumulation. Soybean rotations and cover crops could help remediate P-laden soils after repeated BL application., (Published 2023. This article is a U.S. Government work and is in the public domain in the USA. Journal of Environmental Quality published by Wiley Periodicals LLC on behalf of American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America.)

Carbon monoxide (CO) is an essential "building block" for producing everyday chemicals on industrial scale. Carbon monoxide can also be generated though a lesser-known and sometimes forgotten biorenewable pathways that could be explored to advance biobased production from large and more sustainable sources such as bio-waste treatment. Organic matter decomposition can generate carbon monoxide both under aerobic and anaerobic conditions. While anaerobic carbon monoxide generation is relatively well understood, the aerobic is not. Yet many industrial-scale bioprocesses involve both conditions. This review summarizes the necessary basic biochemistry knowledge needed for realization of initial steps towards biobased carbon monoxide production. We analyzed for the first time, the complex information about carbon monoxide production during aerobic, anaerobic bio-waste treatment and storage, carbon monoxide-metabolizing microorganisms, pathways, and enzymes with bibliometric analysis of trends. The future directions recognizing limitations of combined composting and carbon monoxide production have been discussed in greater detail., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Sobieraj, Stegenta-Dąbrowska, Luo, Koziel and Białowiec.)

In cheetahs, age at first parturition correlates negatively with reproductive lifespan (asymmetric reproductive aging); therefore, breeding cheetahs at a young age is essential to maximize reproductive performance in this species. However, younger females display a significantly reduced frequency of copulatory behaviour, which negatively affects breeding. Volatile organic compounds (VOCs) are known to regulate appropriate behavioural responses in various species, including reproductive behaviour; moreover, they have proven to play a role in captive breeding methods in cheetahs, as well as mate choice. Therefore, the objective of this study was to evaluate the effect of a synthetic scent (SS) on the frequency of the five oestrous behaviour(s) (sniff, rub, roll, spray, and meow-chirp) known to be indicative of oestrus in female cheetahs. Based on the results of a previous study from our research group, five VOCs, identified in the marking fluid of male cheetahs, and known to be pheromones involved in reproductive behaviour, were used to create the SS. This was accomplished by mixing benzaldehyde, acetophenone, indole, dimethyl disulphide and phenol with (99.9%) ethanol. Seven female cheetahs were then observed for one oestrus cycle without stimulation (control) and then once again while exposed to the SS (treatment), which was sprayed on foil trays placed around the outside of each enclosure. The occurrence of the five oestrous behaviours was recorded and tallied per day of observations. Although the SS did not have a significant effect on the frequency of oestrous behaviours displayed by the females used in this study, five of the seven (71%) did show an increase in their behaviour with the SS when oestrogen concentrations were at their highest (peak oestrus), including three of the four younger females. The SS also significantly increased the sniffing behaviour in general. Although the results of this study do indicate that VOCs influence cheetahs and their behaviour, firm conclusions cannot be drawn due to the low number of animals used, as well as the significant effect the observation methods had on the results. Nonetheless, this study represents the first of this kind in cheetahs, therefore representing an important step in determining the role of VOCs in aiding breeding in captivity.

Since the COVID-19 pandemic, improving indoor air quality (IAQ) has become vital for the public as COVID-19 and other infectious diseases can transmit via inhalable aerosols. Air cleaning devices with filtration and targeted pollutant treatment capabilities can help improve IAQ. However, only a few filtration/UV devices have been formally tested for their effectiveness, and little data is publicly available and UV doses comparable. In this research, we upgraded a particulate matter (PM) air filtration prototype by adding UV-C (germicidal) light. We developed realistic UV dose metrics for fast-moving air and selected performance scenarios to quantify the mitigation effect on viable airborne bacteria and PM. The targeted PM included total suspended particulate (TSP) and a coarse-to-fine range sized at PM 10 , PM 4 , PM 2.5 , and PM 1 . The PM and viable airborne bacteria concentrations were compared between the inlet and outlet of the prototype at 0.5 and 1.0 m 3 /s (low and high) air flow modes. The upgraded prototype inactivated nearly 100% of viable airborne bacteria and removed up to 97% of TSP, 91% of PM 10 , 87% of PM 4 , 87% of PM 2.5 , and 88% of PM 1 . The performance in the low flow rate mode was generally better than in the high flow rate mode. The combination of filtration and UV-C treatment provided 'double-barrier' assurance for air purification and lowered the risk of spreading infectious micro-organisms.

Scent is known to play an important role in the reproduction of cheetahs and other felids. In fact, the presence/odor of a male cheetah has been noted to trigger the estrous cycle in females. The objective of this study was to analyze the marking fluid (MF) of male cheetahs from different breeding groups to determine the composition of volatile organic compounds (VOCs) present, with the aim of identifying potential pheromones relating to sexual behavior/attraction in this species. Four breeding (B; age: 8.9 ± 1.3 years old) and four non-breeding (NB; age: 5.5 ± 0.8 years old) males were selected for this study. Samples were collected into a glass beaker, transferred immediately into a 20 mL glass screw-cap vial with a polytetrafluoroethylene (PTFE) coated silicone septum, and stored until analyzed by headspace solid-phase microextraction (HS-SPME) using gas chromatography-mass spectrometry. A contingency test with Fisher's exact test, using the frequency (FREQ) procedure of SAS 9.4, was conducted to determine the difference between the number of VOCs identified per breeding group; furthermore, differences in relative concentration (RC) of the identified VOCs between breeding groups were analyzed using ANOVA for repeated measures with the GLIMMIX procedure. From the 13 MF samples analyzed, 53 VOCs were identified, and 12 were identified in all the samples. Five of these (dimethyl disulfide, benzaldehyde, acetophenone, phenol, and indole) are known to be involved in attraction/sexual behavior in mammals. Between the two groups, the RC of indole was significantly higher in the NB group, whereas the RC of dodecanoic acid was significantly higher in the B group. Although not significant, the RC of benzaldehyde was higher in the B versus the NB group. The results of this study do support the hypothesis of differences in VOCs' between B and NB male cheetahs. However, the overlapping of age and breeding status and the diet differences could not be controlled. Still, the evidence of changes in MF composition in male cheetahs necessitates further studies on possible strategies to improve reproduction in captivity.

Although the "skunky" odor characteristic of cannabis has been widely referenced, its cause has been historically misassigned to unspecified "skunky terpenes". Recent reports from two independent research groups, the Koziel team (March and April 2021) and Oswald team (August and November 2021), have corrected this misassignment by linking the "skunky" character of industrial hemp and cannabis to 3-methyl-2-butene-1-thiol (321MBT). A recent USPTO patent application review clearly indicated that the Oswald team should take full credit for the discovery of this link with respect to cannabis. However, the August 19, 2021 publication of their patent application appears to be their formal public disclosure of 321MBT as the primary source odorant which is responsible for the targeted "skunky" odor. This date is well after the March and April 2021 public disclosures by the Koziel team for the 321MBT/"skunky" odor link relative to both cannabis and industrial hemp. This Viewpoint summarizes the investigative strategy leading to the public disclosure of this historically elusive link. It is presented from the perspective of the rapid multidimensional-gas chromatography-mass spectrometry-olfactometry (i.e., MDGC-MS-O) based odorant-prioritization "screening" approach, as applied by the Koziel team., Competing Interests: The authors declare the following competing financial interest(s): Three commercial entities are represented among the collaborative team (Byers Scientific, Don Wright & Associates, LLC, and Volatile Analysis Corporation)., (© 2022 The Authors. Published by American Chemical Society.)

Diagnosis of diseases in cattle at early stages is of significance both economically and clinically. Non-invasive diagnostic samples such as breath are preferred since they cause minimum inconvenience or pain to the animals. In this review, different sampling devices, sample preparation techniques, instrumentation, and statistical analysis approaches that have been designed and tested are described and compared in terms of their applicability in the diagnosis of common cattle diseases. The sample preparation techniques used include solid-phase microextraction (SPME), sorbent extraction, and needle trap device (NTD). The collected volatile organic compounds (VOCs) are determined using gas chromatography-mass spectrometry (GC-MS) and the electronic nose (e-nose) technology. The majority of studies are focused on the diagnosis of ketosis and bovine respiratory disease (BRD). The common diseases and potential biomarkers are summarized and discussed. Due to the differences in the number of subjects and the type of animals used in different studies, the results are not consistent. Acetone, although detected in almost all studies and subjects, has elevated concentrations in cattle suffering from ketosis. The results of currently available studies were not indicative of specific biomarkers for BRD, and further investigation is required. The current studies have shortcomings in regards to defining useful VOC profiles, the impact on animal welfare, and the practical application at the producer level. While the presented approaches are promising, more controlled, standardized clinical studies need to be conducted before breath analysis can be routinely performed on cattle., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Solving environmental odor issues can be confounded by many analytical, technological, and socioeconomic factors. Considerable know-how and technologies can fail to properly identify odorants responsible for the downwind nuisance odor and, thereby, focus on odor mitigation strategies. We propose enabling solutions to environmental odor issues utilizing troubleshooting techniques developed for the food, beverage, and consumer products industries. Our research has shown that the odorant impact-priority ranking process can be definable and relatively simple. The initial challenge is the prioritization of environmental odor character from the perspective of the impacted citizenry downwind. In this research, we utilize a natural model from the animal world to illustrate the rolling unmasking effect (RUE) and discuss it more systematically in the context of the proposed environmental odorant prioritization process. Regardless of the size and reach of an odor source, a simplification of odor character and composition typically develops with increasing dilution downwind. An extreme odor simplification-upon-dilution was demonstrated for the prehensile-tailed porcupine (P.T. porcupine); its downwind odor frontal boundary was dominated by a pair of extremely potent character-defining odorants: (1) 'onion'/'body odor' and (2) 'onion'/'grilled' odorants. In contrast with the outer-boundary simplicity, the near-source assessment presented considerable compositional complexity and composite odor character difference. The ultimate significance of the proposed RUE approach is the illustration of naturally occurring phenomena that explain why some environmental odors and their sources can be challenging to identify and mitigate using an analytical-only approach (focused on compound identities and concentrations). These approaches rarely move beyond comprehensive lists of volatile compounds emitted by the source. The novelty proposed herein lies in identification of those few compounds responsible for the downwind odor impacts and requiring mitigation focus.

The cheetah species (Acinonyx jubatus ) is currently listed as vulnerable according to the International Union for Conservation of Nature (IUCN). Captive breeding has long since been used as a method of conservation of the species, with the aim to produce a healthy, strong population of cheetahs with an increased genetic variety when compared to their wild counterparts. This would then increase the likelihood of survivability once released into protected areas. Unfortunately, breeding females have been reported to be difficult due to the age of these animals. Older females are less fertile, have more difficult parturition, and are susceptible to asymmetric reproductive aging whereas younger females tend to show a significantly lower frequency of mating behaviour than that of older females, which negatively affects breeding introductions, and therefore mating. Nonetheless, the experience from breeding methods used in some breeding centres in South Africa and the Netherlands, which also rely on the role that semiochemicals play in breeding, proves that cheetahs can be bred successfully in captivity. This review aims to give the reader an in-depth overview of cheetahs' reproductive physiology and behaviour, focusing on the role that pheromones play in this species. Furthermore, it aims to provide new insight into the use of semiochemicals to improve conservation strategies through captive breeding.

Phosphorus (P) is a limited yet essential resource. P cannot be replaced, but it can be recovered from waste. We proposed the TRIZ approach (Teoria reszenija izobretatielskich zadacz - Rus., Theory of Inventive Problem Solving - Eng.) to identify a feasible solution. We aimed at minimizing the environmental impact and, by eliminating contradictions, proposed viable technical solutions. P recovery can be more sustainable based on circular economy and 4Rs (reduction, recovery, reuse, and recycling). The TRIZ approach identified sewage sludge (SS) as waste with a large potential for P recovery (up to 90%). Successful selection and application of SS management and P recovery require a transdisciplinary approach to overcome the various socio-economic, environmental, technical, and legal aspects. The review provides an understanding of principles that must be taken to improve understanding of the whole process of P recovery from wastewater while building on the last two decades of research., (Copyright © 2021 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Porcine reproductive and respiratory syndrome virus (PRRSV) infections cause significant economic losses to swine producers every year. Aerosols containing infectious PRRSV are an important route of transmission, and proper treatment of air could mitigate the airborne spread of the virus within and between barns. Previous bioaerosol studies focused on the microbiology of PRRSV aerosols; thus, the current study addressed the engineering aspects of virus aerosolization and collection. Specific objectives were to (1) build and test a virus aerosolization system, (2) achieve a uniform and repeatable aerosol generation and collection throughout all replicates, (3) identify and minimize sources of variation, and (4) verify that the collection system (impingers) performed similarly. The system for virus aerosolization was built and tested (Obj. 1). The uniform airflow distribution was confirmed using a physical tracer (<12% relative standard deviation) for all treatments and sound engineering control of flow rates (Obj. 2). Theoretical uncertainty analyses and mass balance calculations showed <3% loss of air mass flow rate between the inlet and outlet (Obj. 3). A comparison of TCID 50 values among impinger fluids showed no statistical difference between any two of the three trials ( p -value = 0.148, 0.357, 0.846) (Obj. 4). These results showed that the readiness of the system for research on virus aerosolization and treatment (e.g., by ultraviolet light), as well as its potential use for research on other types of airborne pathogens and their mitigation on a laboratory scale., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2021 Li, Koziel, Zimmerman, Hoff, Zhang, Cheng, Yim-Im, Lee, Chen and Jenks.)

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH 3 ), hydrogen sulfide (H 2 S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH 3 , and other gases (GHGs, O 3 -sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO 2 -based photocatalyst. Treated gas airflow (0.25-0.76 m 3 ∙s -1 ) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to (i) 63% of odor, (ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p -cresol, and indole, respectively, (iii) 14% of nitrous oxide (N 2 O), (iv) 100% of O 3 , and 26% generation of CO 2 . Under UV-C (185 + 254 nm) photocatalysis, the percent reductions of target gases were up to (i) 54% and 47% for p -cresol and indole, respectively, (ii) 25% of N 2 O, (iii) 71% of CH 4 , and 46% and 139% generation of CO 2 and O 3 , respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns. Results from this study are needed to inform the experimental design for future on-farm research with UV-A and UV-C.

In work, data from carbonization of the eight main municipal solid waste components (carton, fabric, kitchen waste, paper, plastic, rubber, paper/aluminum/polyethylene (PAP/AL/PE) composite packaging pack, wood) carbonized at 300-500 °C for 20-60 min were used to build regression models to predict the biochar properties (proximate and ultimate analysis) for particular components. These models were then combined in general models that predict the properties of char made from mixed waste components depending on pyrolysis temperature, residence time, and share of municipal solid waste components. Next, the general models were compared with experimental data (two mixtures made from the above-mentioned components carbonized at the same conditions). The comparison showed that most of the proposed general models had a determination coefficient (R 2 ) over 0.6, and the best prediction was found for the prediction of biochar mass yield (R 2 = 0.9). All models were implemented into a spreadsheet to provide a simple tool to determine the potential of carbonization of municipal solid waste/refuse solid fuel based on a local mix of major components.

Livestock production systems generate nuisance odor and gaseous emissions affecting local communities and regional air quality. There are also concerns about the occupational health and safety of farmworkers. Proven mitigation technologies that are consistent with the socio-economic challenges of animal farming are needed. We have been scaling up the photocatalytic treatment of emissions from lab-scale, aiming at farm-scale readiness. In this paper, we present the design, testing, and commissioning of a mobile laboratory for on-farm research and demonstration of performance in simulated farm conditions before testing to the farm. The mobile lab is capable of treating up to 1.2 m 3 /s of air with titanium dioxide, TiO 2 -based photocatalysis, and adjustable UV-A dose based on LED lamps. We summarize the main technical requirements, constraints, approach, and performance metrics for a mobile laboratory, such as the effectiveness (measured as the percent reduction) and cost of photocatalytic treatment of air. The commissioning of all systems with standard gases resulted in ~9% and 34% reduction of ammonia (NH 3 ) and butan-1-ol, respectively. We demonstrated the percent reduction of standard gases increased with increased light intensity and treatment time. These results show that the mobile laboratory was ready for on-farm deployment and evaluating the effectiveness of UV treatment.

The decrease in the calorific value of refuse-derived fuel (RDF) is an unintended outcome of the progress made toward more sustainable waste management. Plastics and paper separation and recycling leads to the overall decrease in waste's calorific value, further limiting its applicability for thermal treatment. Pyrolysis has been proposed to densify energy in RDF and generate carbonized solid fuel (CSF). The challenge is that the feedstock composition of RDF is variable and site-specific. Therefore, the optimal pyrolysis conditions have to be established every time, depending on feedstock composition. In this research, we developed a model to predict the higher heating value (HHV) of the RDF composed of eight morphological refuse groups after low-temperature pyrolysis in CO 2 (300-500 °C and 60 min) into CSF. The model considers cardboard, fabric, kitchen waste, paper, plastic, rubber, PAP/AL/PE (paper/aluminum/polyethylene) composite packaging pack, and wood, pyrolysis temperature, and residence time. The determination coefficients (R 2 ) and Akaike information criteria were used for selecting the best model among four mathematical functions: (I) linear, (II) second-order polynomial, (III) factorial regression, and (IV) quadratic regression. For each RDF waste component, among these four models, the one best fitted to the experimental data was chosen; then, these models were integrated into the general model that predicts the HHV of CSF from the blends of RDF. The general model was validated experimentally by the application to the RDF blends. The validation revealed that the model explains 70-75% CSF HHV data variability. The results show that the optimal pyrolysis conditions depend on the most abundant waste in the waste mixture. High-quality CSF can be obtained from wastes such as paper, carton, plastic, and rubber when processed at relatively low temperatures (300 °C), whereas wastes such as fabrics and wood require higher temperatures (500 °C). The developed model showed that it is possible to achieve the CSF with the highest HHV value by optimizing the pyrolysis of RDF with the process temperature, residence time, and feedstock blends pretreatment.

The aim of this research was to evaluate the effect of biochar diet supplementation for broiler chickens on (1) ammonia and odor emissions from manure, (2) feed conversion ratio and daily weight gain, and (3) selected meat quality and sensory parameters. Beechwood biochar (BC, 2 and 4%) and BC-glycerin-aluminosilicates mix (BCM, 3 and 6%) were tested as dietary additives. A total of 750 chicken broilers (Ross 308) were divided into five dietary groups with five replicates per group ( n = 5, 30 birds in each replicate) and reared on a littered floor for 5 weeks. Both feed additives showed a significant reduction of ammonia emissions by up to 17%, while the reduction of odor emissions was not statistically significant. The feed conversion ratio increased by 8% for the highest concentration of the mixture. The change of the treated broilers' average body weight ranged in the last week of the experiment from 0 to -7%, with the most negative effect for the highest dose of the mixture. Sensory analysis of the sous-vide cooked breasts showed no significant differences.

Improved technologies are needed for sustainable management of sewage sludge (SS). The torrefaction (also known as biomass "roasting") is considered a pretreatment of SS before use in agriculture. However, it is not known whether the torrefaction has the potential to decrease heavy metals' (HMs) leachability and the SS toxicity. Thus, the aim of the study was to evaluate the influences of the SS torrefaction parameters (temperature and process time) on HM contents in biochar, HM leachability, and biochar toxicity, and compare them with raw SS. The experiments were designed in 18 combinations (six temperatures, 200, 220, 240, 260, 280, and 300 °C; and three process times-20, 40, 60 min). Standard tests were used to determine HMs content, leachability, and toxicity. Results indicated that the torrefaction did not increase ( p < 0.05) the HM content in comparison to the raw SS. The leachability of Zn, Ni, Cu, Cr, and Mn from SS biochars was similar to raw SS. However, the degree of leachability varied significantly ( p < 0.05) from as low as 0.1% for Cu to high as 16.7% for Cd. The leachability of Cd (<16.7%) and Pb (<11.9%) from biochars was higher than from raw SS (<6.1% and <2.4%, respectively). The leachability of Cd from SS biochar, in five torrefaction combinations, was higher than the threshold value for hazardous waste. It is recommended that site-specific decisions are made for torrefaction of SS with respect to its HM content, as the resulting biochar could be considered as hazardous waste, depending on the feedstock. Moreover, the biochar produced under the whole range of temperatures during 20 min retention time significantly ( p < 0.05) increased the Daphnia magna Straus mobility inhibition by up to 100% in comparison to the biochar obtained during 40 and 60 min torrefaction. Taking into account the increased leachability of specific HMs and D. magna Straus mobility inhibition, biochar should be considered a potentially hazardous material. Future research should focus on biochar dosage as a fertilizer in relation to its toxicity. Additional research is warranted to focus on the optimization of SS torrefaction process parameters affecting the toxicity.

Mitigation of potentially hazardous and malodor compounds emitted from animal waste is needed to improve the sustainability of livestock agriculture. Bacteria control the generation of these compounds and also depend on the pH of manure. Influencing swine manure pH, especially on the liquid-air interface, may lead to a reduction of emission of odorous and hazardous compounds. The objective of this experiment was to test highly alkaline and porous (HAP) modified biochar with pH = 9.2 and red oak (RO) biochar with pH = 7.5 influence on swine manure pH acquired from the outdoor storage and deep pit storage under a barn. HAP and RO biochars were topically applied on the outdoor-stored (pH = 7.55), and pit (pH = 8.00) manures and spatial pH (every 1 mm of depth) were measured on days 0, 2, and 4. Results showed that HAP biochar increased outdoor-stored manure pH on day 4, particularly within the top 10 mm of depth, where pH ranged from 7.79 to 8.90, while in the case of RO pH ranged between 7.46 and 7.66, i.e., similar to control (7.57-7.64). Both biochars decreased pit-stored manure pH within the top 10 mm of depth (in comparison with the control pH of 8.36-8.47) to 8.19-8.30 (HAP), and 8.18-8.29 (RO) on day 4. However, differences were not considerable. The reason for the insignificant effect of biochars on pit manure was likely due to its higher buffer capacity in comparison with the outdoor-stored manure., (Copyright © 2020 Meiirkhanuly, Koziel, Bialowiec, Banik and Brown.)

Poultry farmers are producing eggs, meat, and feathers with increased efficiency and lower carbon footprint. Technologies to address concerns about the indoor air quality inside barns and the gaseous emissions from farms to the atmosphere continue to be among industry priorities. We have been developing and scaling up a UV air treatment that has the potential to reduce odor and other gases on the farm scale. In our recent laboratory-scale study, the use of UV-A (a less toxic ultraviolet light, a.k.a. "black light") and a special TiO 2 -based photocatalyst reduced concentrations of several important air pollutants (NH 3 , CO 2 , N 2 O, O 3 ) without impact on H 2 S and CH 4 . Therefore, the objectives of this research were to (1) scale up the UV treatment to pilot scale, (2) evaluate the mitigation of odor and odorous volatile organic compounds (VOCs), and (3) complete preliminary economic analyses. A pilot-scale experiment was conducted under commercial poultry barn conditions to evaluate photocatalyst coatings on surfaces subjected to UV light under field conditions. In this study, the reactor was constructed to support interchangeable wall panels and installed on a poultry farm. The effects of a photocatalyst's presence (photocatalysis and photolysis), UV intensity (LED and fluorescent), and treatment time were studied in the pilot-scale experiments inside a poultry barn. The results of the pilot-scale experiments were consistent with the laboratory-scale one: the percent reduction under photocatalysis was generally higher than photolysis. In addition, the percent reduction of target gases at a high light intensity and long treatment time was higher. The percent reduction of NH 3 was 5-9%. There was no impact on H 2 S, CH 4 , and CO 2 under any experimental conditions. N 2 O and O 3 concentrations were reduced at 6-12% and 87-100% by both photolysis and photocatalysis. In addition, concentrations of several VOCs responsible for livestock odor were reduced from 26 to 62% and increased with treatment time and light intensity. The odor was reduced by 18%. Photolysis treatment reduced concentrations of N 2 O, VOCs, and O 3 , only. The initial economic analysis has shown that LEDs are more efficient than fluorescent lights. Further scale-up and research at farm scale are warranted., (Copyright © 2020 Lee, Li, Koziel, Ahn, Wi, Chen, Meiirkhanuly, Banik and Jenks.)

Sewage sludge (SS) recycling is an important part of the proposed 'circular economy' concept. SS can be valorized via torrefaction (also known as 'low-temperature pyrolysis' or 'roasting'). SS can, therefore, be considered a low-quality fuel or a source of nutrients essential for plant growth. Biochar produced by torrefaction of SS is a form of carbonized fuel or fertilizer. In this research, for the first time, we tested the feasibility of torrefaction of SS with high ash content for either fuel or organic fertilizer production. The research was conducted in 18 variants (six torrefaction temperatures between 200~300 °C, and three process residence times of 20, 40, 60 min) in 5 repetitions. Fuel and fertilizer properties and multiple regression analysis of produced biochar were conducted. The higher heating value (HHV) of raw SS was 21.2 MJ·kg -1 . Produced biochar was characterized by HHV up to 12.85 MJ·kg -1 and lower H/C and O/C molar ratio. Therefore, torrefaction of SS with high ash content should not be considered as a method for improving the fuel properties. Instead, the production of fertilizer appears to be favorable. The torrefaction increased C, N, Mg, Ca, K, Na concentration in relation to raw SS. No significant ( p < 0.05) influence of the increase of temperature and residence time on the increase of biogenic elements in biochar was found, however the highest biogenic element content, were found in biochar produced for 60 min, under the temperature ranging from 200 to 240 °C. Obtained biochars met the Polish regulatory criteria for mineral-organic fertilizer. Therefore SS torrefaction may be considered a feasible waste recycling technology. The calculation of torrefaction energy and the mass balance shows energy demand <2.5 GJ∙Mg -1 w.m., and the expected mass yield of the product, organic fertilizer, is ~178 kg∙Mg -1 w.m of SS. Further investigation should consider the scaling-up of the SS torrefaction process, with the application of other types of SSs.

Carbon monoxide (CO), an air pollutant and a toxic gas to humans, can be generated during aerobic digestion of organic waste. CO is produced due to thermochemical processes, and also produced or consumed by cohorts of methanogenic, acetogenic, or sulfate-reducing bacteria. The exact mechanisms of biotic and abiotic formation of CO in aerobic digestion (particularly the effects of process temperature) are still not known. This study aimed to determine the temporal variation in CO concentrations during the aerobic digestion as a function of process temperature and activity of microorganisms. All experiments were conducted in controlled temperature reactors using homogeneous materials. The lab-scale tests with sterilized and non-sterilized mix of green waste, dairy cattle manure, sawdust (1:1:1 mass ratio) were carried out for 1 week at 10, 25, 30, 37, 40, 50, 60, 70°C to elucidate the biotic vs. abiotic effect. Gas concentrations of CO, O 2 , and CO 2 inside the reactor were measured every 12 h. The CO concentrations observed for up to 30°C did not exceed 100 ppm v/v. For 50 and 60°C, significantly ( p < 0.05) higher CO concentrations, reaching almost 600 ppm v/v, were observed. The regression analyses showed in both cases (sterile and non-sterile) a statistically significant effect ( p < 0.05) of temperature on CO concentration, confirming that the increase in temperature causes an increase in CO concentration. The remaining factors (time, O 2 , and CO 2 content) were not statistically significant ( p > 0.05). A new polynomial model describing the effect of temperature, O 2 , and CO 2 concentration on CO production during aerobic digestion of organic waste was formulated. It has been found that the proposed model for sterile variant had a better fit ( R 2 = 0.86) compared with non-sterile ( R 2 = 0.71). The model predicts CO emissions and could be considered for composting process optimization. The developed model could be further developed and useful for ambient air quality and occupational exposure to CO., (Copyright © 2019 Stegenta-Dąbrowska, Drabczyński, Sobieraj, Koziel and Białowiec.)

Experimental optimization of analytical methods based on solid-phase microextraction (SPME) is a complex and labor-intensive process associated with uncertainties. Using the theoretical basics of SPME and finite element analysis software for the optimization proved to be an efficient alternative. In this study, an improved finite element analysis-based model for SPME of volatile organic compounds (VOCs) by porous coatings was developed mainly focussing on the mass transport in coatings. Benzene and the Carboxen/polydimethylsiloxane (Car/PDMS) coating were used as the model VOC and a porous SPME coating, respectively. It has been established that in the coating, volumetric fractions of Carboxen, PDMS, and air are 33, 42 and 24%, respectively. Knudsen diffusion in micropores can slow down a mass transport of analytes in the coating. When PDMS was considered as the solid part of the coating, lower root-mean-square deviation of the modeling results from experimental data was observed. It has been shown that the developed model can be used to model the extraction of VOCs from air and water samples encountered in a typical SPME development method procedure. It was possible to determine system equilibration times and use them to optimize sample volume and Henry's law constant. The developed model is relatively simple, fast, and can be recommended for optimization of extraction parameters for other analytes and SPME coatings. The diffusivity of analytes in a coating is an important property needed for improved characterization of existing and new SPME polymers and analytical method optimization., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Oxytree is a fast-growing energy crop with C4 photosynthesis. In this research, for the first time, the torrefaction kinetic parameters of pruned Oxytree biomass ( Paulownia clon in Vitro 112) were determined. The influence of the Oxytree cultivation method and soil class on the kinetic parameters of the torrefaction was also investigated. Oxytree pruned biomass from a first-year plantation was subjected to torrefaction within temperature range from 200 to 300 °C and under anaerobic conditions in the laboratory-scale batch reactor. The mass loss was measured continuously during the process. The relative mass loss increased from 1.22% to 19.56% with the increase of the process temperature. The first-order constant rate reaction ( k ) values increased from 1.26 × 10 -5 s -1 to 7.69 × 10 -5 s -1 with the increase in temperature. The average activation energy for the pruned biomass of Oxytree torrefaction was 36.5 kJ∙mol -1 . Statistical analysis showed no significant ( p < 0.05) effect of the Oxytree cultivation method and soil class on the k value. The results of this research could be useful for the valorization of energy crops such as Oxytree and optimization of waste-to-carbon and waste-to-energy processes., Competing Interests: The authors declare no conflict of interest.

The primary hurdle for diagnosis of some diseases is the long incubation required to culture and confirm the presence of bacteria. The concept of using microbial VOCs as "signature markers" could provide a faster and noninvasive diagnosis. Finding biomarkers is challenging due to the specificity required in complex matrices. The objectives of this study were to (1) build/test a lab-scale platform for screening of microbial VOCs and (2) apply it to Mycobacterium avium paratuberculosis; the vaccine strain of M. bovis Bacillus Calmette-Guérin; and M. kansasii to demonstrate detection times greater those typically required for culture. SPME-GC-MS was used for sampling, sample preparation, and analyses. For objective (1), a testing platform was built for headspace sampling of bacterial cultures grown in standard culture flasks via a biosecure closed-loop circulating airflow system. For (2), results show that the suites of VOCs produced by Mycobacteria ssp. change over time and that individual strains produce different VOCs. The developed method was successful in discriminating between strains using a pooled multi-group analysis, and in timepoint-specific multi- and pair-wise comparisons. The developed testing platform can be useful for minimally invasive and biosecure collection of biomarkers associated with human, wildlife and livestock diseases for development of diagnostic point-of-care and field surveillance.

Biowaste generated in the process of Oxytree cultivation and logging represents a potential source of energy. Torrefaction (a.k.a. low-temperature pyrolysis) is one of the methods proposed for the valorization of woody biomass. Still, energy is required for the torrefaction process during which the raw biomass becomes torrefied biomass with fuel properties similar to those of lignite coal. In this work, models describing the influence of torrefaction temperature and residence time on the resulting fuel properties (mass and energy yields, energy densification ratio, organic matter and ash content, combustible parts, lower and higher heating values, CHONS content, H:C and O:C ratios) were proposed according to the Akaike criterion. The degree of the models' parameters matching the raw data expressed as the determination coefficient (R 2 ) ranged from 0.52 to 0.92. Each model parameter was statistically significant ( p < 0.05). Estimations of the value and quantity of the produced torrefied biomass from 1 Mg of biomass residues were made based on two models and a set of simple assumptions. The value of torrefied biomass (€123.4·Mg -1 ) was estimated based on the price of commercially available coal fuel and its lower heating value ( LHV ) for biomass moisture content of 50%, torrefaction for 20 min at 200 °C. This research could be useful to inform techno-economic analyses and decision-making process pertaining to the valorization of pruned biomass residues.

Waste can be effectively reused through the production of carbonized refuse-derived fuel (CRDF) that enables further energy recovery. Developing cleaner production of CRDF requires consideration of practical issues of storage and handling. Thus, it needs to be ensured that CRDF does not pose an excessive risk to humans and the ecosystem. Very few studies indicate a wide variety of volatile organic compounds (VOCs) are present in CRDF, some of which are toxic. During handling, storage, transportation, and use of VOC-rich CRDF, workers and end-users could be exposed to emissions that could pose a health and safety hazard. Our recent study shows that CRDF densification via pelletization can increase the efficiency of storage and transportation. Thus, the following research question was identified: can pelletization mitigate VOCs emissions from CRDF during storage? Preliminary research aiming at the determination of the influence of CRDF pelletization on VOCs emission during storage was completed to address this question. The VOCs emissions from two types of CRDF: ground (loose, torrefied refuse-derived fuel (RDF)) and pelletized, were measured. Pelletization reduced the VOCs emissions potential during the four-day storage by ~86%, in comparison with ground CRDF. Mitigation of VOCs emissions from densified CRDF is feasible, and research is warranted to understand the influence of structural modification on VOCs emission kinetics, and possibilities of scaling up this solution into the practice of cleaner storage and transportation of CRDF.

Technologies for controlling gaseous emissions of livestock is of interest to producers, the public, and regulatory agencies. In our previous lab-scale study, the use of a photocatalytic coating on surfaces subjected to black ultraviolet light reduced emissions of key odorant compounds relevant to the livestock industry. Thus, an on-farm pilot-scale experiment was conducted at a commercial swine barn to evaluate a photocatalytic coating on surfaces subjected to ultraviolet light under field conditions. A flow-through reactor was constructed with a TiO 2 -based photocatalytic coating on the interior surfaces and black ultraviolet light fixtures. The reactor was deployed in a room downstream of the entire swine barn exhaust. Gas samples were collected from three sampling ports in the reactor, one at the inlet (control), the midpoint (half treatment) and the outlet (treatment). Compared to the control, significant reductions in emissions were observed for p-cresol (22%), odor (16%) and nitrous oxide (9%). A significant increase in carbon dioxide (3%) was also measured. Results show that the TiO 2 -based photocatalytic coating and black UV light are effective in mitigating odor, a key VOC responsible for downwind swine odor, and one important greenhouse effect gas when subjected to swine barn exhaust., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

In this research, we explore for the first time the use of leaf stomatal conductance (g s ) for phytotoxicity assessment. Plants respond to stress by regulating transpiration. Transpiration can be correlated with stomatal conductance when the water vapor pressure gradient for transpiration is constant. Thus, our working hypothesis was that the g s measurement could be a useful indicator of the effect of toxic compounds on plants. This lab-scale study aimed to test the measurement of g s as a phytotoxicity indicator. Our model plants were two common hydrophytes used in zero-effluent constructed wetlands for treating landfill leachate. The toxic influence of two types of leachate from old landfills (L1, L2) on common reed ( Phragmites australis (Cav.) Trin. ex Steud.) and sweet flag ( Acorus calamus L.) was tested. The g s measurements correlated well with plant response to treatments with six solutions (0 to 100%) of landfill leachate. Sweet flag showed higher tolerance to leachate solutions compared to common reed. The estimated lowest effective concentration (LOEC) causing the toxic effect values for these leachates were 3.94% of L1 and 5.76% of L2 in the case of reed, and 8.51% of L1 and 10.44% of L2 in the case of sweet flag. Leachate L1 was more toxic than L2. The leaf stomatal conductance measurement can be conducted in vivo and in the field. The proposed approach provides a useful parameter for indicating plant responses to the presence of toxic factors in the environment.

In this research, we propose a novel concept for a non-destructive evaluation of volatiles emitted from ripening grapes using solid-phase microextraction (SPME). This concept is novel to both the traditional vinifera grapes and the cold-hardy cultivars. Our sample models are cold-hardy varieties in the upper Midwest for which many of the basic multiyear grape flavor and wine style data is needed. Non-destructive sampling included a use of polyvinyl fluoride (PVF) chambers temporarily enclosing and concentrating volatiles emitted by a whole cluster of grapes on a vine and a modified 2 mL glass vial for a vacuum-assisted sampling of volatiles from a single grape berry. We used SPME for either sampling in the field or headspace of crushed grapes in the lab and followed with analyses on gas chromatography-mass spectrometry (GC-MS). We have shown that it is feasible to detect volatile organic compounds (VOCs) emitted in-vivo from single grape berries (39 compounds) and whole clusters (44 compounds). Over 110 VOCs were released to headspace from crushed berries. Spatial (vineyard location) and temporal variations in VOC profiles were observed for all four cultivars. However, these changes were not consistent by growing season, by location, within cultivars, or by ripening stage when analyzed by multivariate analyses such as principal component analysis (PCA) and hierarchical cluster analyses (HCA). Research into aroma compounds present in cold-hardy cultivars is essential to the continued growth of the wine industry in cold climates and diversification of agriculture in the upper Midwestern area of the U.S.

Finding farm-proven, robust sampling technologies for measurement of odorous volatile organic compounds (VOCs) and evaluating the mitigation of nuisance emissions continues to be a challenge. The objective of this research was to develop a new method for quantification of odorous VOCs in air using time-weighted average (TWA) sampling. The main goal was to transform a fragile lab-based technology (i.e., solid-phase microextraction, SPME) into a rugged sampler that can be deployed for longer periods in remote locations. The developed method addresses the need to improve conventional TWA SPME that suffers from the influence of the metallic SPME needle on the sampling process. We eliminated exposure to metallic parts and replaced them with a glass tube to facilitate diffusion from odorous air onto an exposed SPME fiber. A standard gas chromatography (GC) liner recommended for SPME injections was adopted for this purpose. Acetic acid, a common odorous VOC, was selected as a model compound to prove the concept. GC with mass spectrometry (GC⁻MS) was used for air analysis. An SPME fiber exposed inside a glass liner followed the Fick's law of diffusion model. There was a linear relationship between extraction time and mass extracted up to 12 h ( R ² > 0.99) and the inverse of retraction depth (1/ Z ) ( R ² > 0.99). The amount of VOC adsorbed via the TWA SPME using a GC glass liner to protect the SPME was reproducible. The limit of detection (LOD, signal-to-noise ratio (S/N) = 3) and limit of quantification (LOQ, S/N = 5) were 10 and 18 µg·m -3 (4.3 and 7.2 ppbV), respectively. There was no apparent difference relative to glass liner conditioning, offering a practical simplification for use in the field. The new method related well to field conditions when comparing it to the conventional method based on sorbent tubes. This research shows that an SPME fiber exposed inside a glass liner can be a promising, practical, simple approach for field applications to quantify odorous VOCs.

The Midwest wine industry has shown a marked increase in growers, hectares planted, wineries, and wine production. This growth coincides with the release of cold-hardy cultivars such as Brianna and Frontenac gris, in 2001 and 2003, respectively. These white grape varieties account for one-third of the total area grown in the state of Iowa. It is generally accepted that the wine aroma profile plays a crucial role in developing a local, sustainable brand. However, the identity of Brianna/Frontenac Gris-based wine aromas and their link to the grape berry chemistry at harvest is unknown. This study aims to preliminarily characterize key odor-active compounds that can influence the aroma profile in wines made from Brianna and Frontenac gris grapes harvested at different stages of ripening. Brianna and Frontenac gris grapes were harvested approximately 7 days apart, starting at 15.4 °Brix (3.09 pH) and 19.5 °Brix (3.00 pH), respectively. Small batch fermentations were made for each time point with all juices adjusted to the same °Brix prior to fermentation. Odor-active compounds were extracted from wine headspace using solid-phase microextraction (SPME) and analyzed by gas chromatography-mass spectrometry (GC-MS) and simultaneous olfactometry (O). Over 30 odor-active compounds were detected. Aromas in Brianna wines developed from "cotton candy" and "floral", to "banana" and "butterscotch", then finally to "honey", "caramel" and an unknown neutral aroma. Frontenac gris wines changed from an unknown neutral aroma to "fruity" and "rose". Results from the lay audiences' flavor and aroma descriptors also indicate a shift with harvest date and associated °Brix. To date, this is the first report of wine aromas from Brianna and Frontenac gris by GC-MS-O. Findings from this research support the hypothesis that aroma profiles of Brianna and Frontenac gris wines can be influenced by harvesting the grapes at different stages of ripening.

Burial of infectious and potentially infectious livestock and poultry animals is the most common response to an emergency situation. The data set summarizes 22-week-long experiment that simulates the environment found within conventional burial trenches for emergency disposal of animal carcasses, worldwide, sometimes with a topical application of quicklime as it is required in the Republic of Korea. This data set shows the rarely presented evidence of the extremely slow decay of animal carcasses. Besides visual evidence of no visible breakdown of carcass material, i.e., carcass (or carcass quarters and coarse cuts) still resembled the initial material at the end of the study, we present data characterizing the process. Specifically, temporal variations of digestate quality (pH, ammonia, volatile fatty acids), biogas production, and the persistence of odorous volatile organic compounds are summarized. The data provide important evidence of undesirable, slow progression of the digestion process. The evidence of failure to achieve practical endpoints with the anaerobic digestion provides the impetus for seeking alternative, improved methods of disposal that will be feasible in emergency context, such as aerated burial concept (Koziel et al., 2018 [1]).

In this work, for the first time, the volatile organic compound (VOC) emissions from carbonized refuse-derived fuel (CRDF) were quantified on a laboratory scale. The analyzed CRDF was generated from the torrefaction of municipal waste. Headspace solid-phase microextraction (SPME) and gas chromatography-mass spectrometry (GC-MS) was used to identify 84 VOCs, including many that are toxic, e.g., derivatives of benzene or toluene. The highest emissions were measured for nonanal, octanal, and heptanal. The top 10 most emitted VOCs contributed to almost 65% of the total emissions. The VOC mixture emitted from torrefied CRDF differed from that emitted by other types of pyrolyzed biochars, produced from different types of feedstock, and under different pyrolysis conditions. SPME was a useful technology for surveying VOC emissions. Results provide an initial database of the types and relative quantities of VOCs emitted from CRDF. This data is needed for further development of CRDF technology and comprehensive assessment of environmental impact and practical storage, transport, and potential adoption of CRDF as means of energy and resource recovery from municipal waste.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of the TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics, Burlington, MA, USA). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of their concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth ( Z ) resulted in better recoveries. Sampling of studied VOCs using 23 ga Carboxen/polydimethylsiloxane (Car/PDMS) assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 × 0.75 mm internal diameter SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The results obtained can be used to develop a more accurate analytical method for determination of TWA concentrations of VOCs in air using SPME. The developed model can be used to simulate sampling of other environments (process gases, water) by retracted SPME fibers.

Nearly 55,000 outbreaks of animal disease were reported to the World Animal Health Information Database between 2005 and 2016. To suppress the spread of disease, large numbers of animal mortalities often must be disposed of quickly and are frequently buried on the farm where they were raised. While this method of emergency disposal is fast and relatively inexpensive, it also can have undesirable and lasting impacts (slow decay, concerns about groundwater contamination, pathogens re-emergence, and odor). Following the 2010 foot-and-mouth disease outbreak, the Republic of Korea's National Institute of Animal Science funded research on selected burial alternatives or modifications believed to have potential to reduce undesirable impacts of burial. One such modification involves the injection of air into the liquid degradation products from the 60-70% water from decomposing carcasses in lined burial trenches. Prior to prototype development in the field, a laboratory-scale study of aerated decomposition (AeD) of poultry carcasses was conducted to quantify improvements in time of carcass decomposition, reduction of potential groundwater pollutants in the liquid products of decomposition (since trench liners may ultimately leak), and reduction of odorous VOCs emitted during decomposition. Headspace gases also were monitored to determine the potential for using gaseous biomarkers in the aerated burial trench exhaust stream to monitor completion of the decomposition. Results of the lab-scale experiments show that the mass of chicken carcasses was reduced by 95.0 ± 0.9% within 3 months at mesophilic temperatures (vs. negligible reduction via mesophilic anaerobic digestion typical of trench burial) with concomitant reduction of biochemical oxygen demand (BOD; 99%), volatile suspended solids (VSS; 99%), total suspended solids (TSS; 99%), and total ammonia nitrogen (TAN; 98%) in the liquid digestate. At week #7 BOD and TSS in digestate met the U.S. EPA standards for treated wastewater discharge to surface water. Salmonella and Staphylococcus were inactivated by the AeD process after week #1 and #3, respectively. Five gaseous biomarkers: pyrimidine; p-cresol; phenol; dimethyl disulfide; and dimethyl trisulfide; were identified and correlated with digestate quality. Phenol was the best predictor of TAN (R = 0.96), BOD (R = 0.92), and dissolved oxygen (DO) (R = -0.91). Phenol was also the best predictor populations of Salmonella (R = 0.95) and aerobes (R = 0.88). P-cresol was the best predictor for anaerobes (R = 0.88). The off-gas from AeD will require biofiltration or other odor control measures for a much shorter time than anaerobic decomposition. The lab-scale studies indicate that AeD burial has the potential to make burial a faster, safer, and more environmentally friendly method for emergency disposal and treatment of infectious animal carcasses and that this method should be further developed via prototype-scale field studies., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

A passive sampling method, using retracted solid-phase microextraction (SPME) - gas chromatography-mass spectrometry and time-weighted averaging, was developed and validated for tracking marker volatile organic compounds (VOCs) emitted during aerobic digestion of biohazardous animal tissue. The retracted SPME configuration protects the fragile fiber from buffeting by the process gas stream, and it requires less equipment and is potentially more biosecure than conventional active sampling methods. VOC concentrations predicted via a model based on Fick's first law of diffusion were within 6.6-12.3% of experimentally controlled values after accounting for VOC adsorption to the SPME fiber housing. Method detection limits for five marker VOCs ranged from 0.70 to 8.44ppbv and were statistically equivalent (p>0.05) to those for active sorbent-tube-based sampling. The sampling time of 30min and fiber retraction of 5mm were found to be optimal for the tissue digestion process., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Lions (Panthera leo) use chemical signaling to indicate health, reproductive status, and territorial ownership. To date, no study has reported on both scent and composition of marking fluid (MF) from P. leo. The objectives of this study were to: 1) develop a novel method for simultaneous chemical and scent identification of lion MF in its totality (urine + MF), 2) identify characteristic odorants responsible for the overall scent of MF as perceived by human panelists, and 3) compare the existing library of known odorous compounds characterized as eliciting behaviors in animals in order to understand potential functionality in lion behavior. Solid-phase microextraction and simultaneous chemical-sensory analyses with multidimensional gas-chromatography-mass spectrometry-olfactometry improved separating, isolating, and identifying mixed (MF, urine) compounds versus solvent-based extraction and chemical analyses. 2,5-Dimethylpyrazine, 4-methylphenol, and 3-methylcyclopentanone were isolated and identified as the compounds responsible for the characteristic odor of lion MF. Twenty-eight volatile organic compounds (VOCs) emitted from MF were identified, adding a new list of compounds previously unidentified in lion urine. New chemicals were identified in nine compound groups: ketones, aldehydes, amines, alcohols, aromatics, sulfur-containing compounds, phenyls, phenols, and volatile fatty acids. Twenty-three VOCs are known semiochemicals that are implicated in attraction, reproduction, and alarm-signaling behaviors in other species.

Bovine tuberculosis is a zoonotic disease of global public health concern. Development of diagnostic tools to improve test accuracy and efficiency in domestic livestock and enable surveillance of wildlife reservoirs would improve disease management and eradication efforts. Use of volatile organic compound analysis in breath and fecal samples is being developed and optimized as a means to detect disease in humans and animals. In this study we demonstrate that VOCs present in fecal samples can be used to discriminate between non-vaccinated and BCG-vaccinated cattle prior to and after Mycobacterium bovis challenge.

Managing the disposal of infectious animal carcasses from routine and catastrophic disease outbreaks is a global concern. Recent research suggests that burial in lined and aerated trenches provides the rapid pathogen containment provided by burial, while reducing air and water pollution potential and the length of time that land is taken out of agricultural production. Survival of pathogens in the digestate remains a concern, however. A potential answer is a 'dual'-barrier approach in which ammonia is used as a secondary barrier treatment to reduce the risk of pathogen contamination when trench liners ultimately leak. Results of this study showed that the minimum inhibitory concentration (MIC) of NH3 is 0.1 M (~1,468 NH3-N mg/L), and 0.5 M NH3 (~7,340 NH3-N mg/L) for ST4232 & MRSA43300, respectively at 24 h and pH = 9±0.1 and inactivation was increased by increasing NH3 concentration and/or treatment time. Results for digestate treated with NH3 were consistent with the MICs, and both pathogens were completely inactivated within 24 h.

Benzene, toluene, ethylbenzene and xylenes (BTEX) comprise one of the most ubiquitous and hazardous groups of ambient air pollutants of concern. Application of standard analytical methods for quantification of BTEX is limited by the complexity of sampling and sample preparation equipment, and budget requirements. Methods based on SPME represent simpler alternative, but still require complex calibration procedures. The objective of this research was to develop a simpler, low-budget, and accurate method for quantification of BTEX in ambient air based on SPME and GC-MS. Standard 20-mL headspace vials were used for field air sampling and calibration. To avoid challenges with obtaining and working with 'zero' air, slope factors of external standard calibration were determined using standard addition and inherently polluted lab air. For polydimethylsiloxane (PDMS) fiber, differences between the slope factors of calibration plots obtained using lab and outdoor air were below 14%. PDMS fiber provided higher precision during calibration while the use of Carboxen/PDMS fiber resulted in lower detection limits for benzene and toluene. To provide sufficient accuracy, the use of 20mL vials requires triplicate sampling and analysis. The method was successfully applied for analysis of 108 ambient air samples from Almaty, Kazakhstan. Average concentrations of benzene, toluene, ethylbenzene and o-xylene were 53, 57, 11 and 14µgm(-3), respectively. The developed method can be modified for further quantification of a wider range of volatile organic compounds in air. In addition, the new method is amenable to automation., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Scent-marking is the most effective method of communication in the presence or absence of a signaler. These complex mixtures result in a multifaceted interaction triggered by the sense of smell. The objective was to identify volatile organic compound (VOC) composition and odors emitted by total marking fluid (MF) associated with Siberian tigers (Panthera tigris altaica). Siberian tiger, an endangered species, was chosen because its MF had never been analyzed. Solid phase microextraction (SPME) for headspace volatile collection combined with multidimensional gas chromatography-mass spectrometry-olfactometry for simultaneous chemical and sensory analyses were used. Thirty-two VOCs emitted from MF were identified. 2-acetyl-1-pyrroline, the sole previously identified compound responsible for the "characteristic" odor of P. tigris MF, was identified along with two additional compounds confirmed with standards (urea, furfural) and four tentatively identified compounds (3-methylbutanamine, (R)-3-methylcyclopentanone, propanedioic acid, and 3-hydroxybutanal) as being responsible for the characteristic aroma of Siberian tiger MF. Simultaneous chemical and sensory analyses improved characterization of scent-markings and identified compounds not previously reported in MF of other tiger species. This research will assist animal ecologists, behaviorists, and zookeepers in understanding how scents from specific MF compounds impact tiger and wildlife communication and improve management practices related to animal behavior. Simultaneous chemical and sensory analyses is applicable to unlocking scent-marking information for other species.

The livestock and poultry production industry, regulatory agencies, and researchers lack a current, science-based guide and data base for evaluation of air quality mitigation technologies. Data collected from science-based review of mitigation technologies using practical, stakeholders-oriented evaluation criteria to identify knowledge gaps/needs and focuses for future research efforts on technologies and areas with the greatest impact potential is presented in the Literature Database tab on the air management practices tool (AMPAT). The AMPAT is web-based (available at www.agronext.iastate.edu/ampat) and provides an objective overview of mitigation practices best suited to address odor, gaseous, and particulate matter (PM) emissions at livestock operations. The data was compiled into Excel spreadsheets from a literature review of 265 papers was performed to (1) evaluate mitigation technologies performance for emissions of odor, volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), particulate matter (PM), and greenhouse gases (GHGs) and to (2) inform future research needs.

A passively-ventilated plastic-wrapped composting system initially developed for biosecure disposal of poultry mortalities caused by avian influenza was adapted and tested to assess its potential as an emergency disposal option for disease-related swine mortalities. Fresh air was supplied through perforated plastic tubing routed through the base of the compost pile. The combined air inlet and top vent area is ⩽∼1% of the gas exchange surface of a conventional uncovered windrow. Parameters evaluated included: (1) spatial and temporal variations in matrix moisture content (m.c.), leachate production, and matrix O2 concentrations; (2) extent of soft tissue decomposition; and (3) internal temperature and the success rate in achieving USEPA time/temperature (T) criteria for pathogen reduction. Six envelope materials (wood shavings, corn silage, ground cornstalks, ground oat straw, ground soybean straw, or ground alfalfa hay) and two initial m.c.'s (15-30% w.b. for materials stored indoors, and 45-65% w.b. to simulate materials exposed to precipitation) were tested to determine their effect on performance parameters (1-3). Results of triple-replicated field trials showed that the composting system did not accumulate moisture despite the 150kg carcass water load (65% of 225kg total carcass mass) released during decomposition. Mean compost m.c. in the carcass layer declined by ∼7 percentage points during 8-week trials, and a leachate accumulation was rare. Matrix O2 concentrations for all materials other than silage were ⩾10% using the equivalent of 2m inlet/vent spacing. In silage O2 dropped below 5% in some cases even when 0.5m inlet/vent spacing was used. Eight week soft tissue decomposition ranged from 87% in cornstalks to 72% in silage. Success rates for achievement of USEPA Class B time/temperature criteria ranged from 91% for silage to 33-57% for other materials. Companion laboratory biodegradation studies suggest that Class B success rates can be improved by slightly increasing envelope material m.c. Moistening initially dry (15% m.c.) envelope materials to 35% m.c. nearly doubled their heat production potential, boosting it to levels ⩾silage. The 'contradictory' silage test results showing high temperatures paired with slow soft tissue degradation are likely due to this material's high density, low gas permeability and low water vapor loss. While slow decomposition typically suggests low microbial activity and heat production, it does not rule out high internal temperatures if the heat produced is conserved. Occasional short-term odor releases during the first 2weeks of composting were associated with top-to-bottom gas flow which is contrary to the typical bottom-to-top flow typically observed in conventional compost piles. In cases where biosecurity concerns are paramount, results of this study show the plastic-wrapped passively-ventilated composting method to have good potential for above-ground swine mortality disposal., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Recent U.S. legislation permitting recreational use of marijuana in certain states brings the use of marijuana odor as probable cause for search and seizure to the forefront of forensic science, once again. This study showed the use of solid-phase microextraction with multidimensional gas chromatography--mass spectrometry and simultaneous human olfaction to characterize the total aroma of marijuana. The application of odor activity analysis offers an explanation as to why high volatile chemical concentration does not equate to most potent odor impact of a certain compound. This suggests that more attention should be focused on highly odorous compounds typically present in low concentrations, such as nonanal, decanol, o-cymene, benzaldehyde, which have more potent odor impact than previously reported marijuana headspace volatiles.