Search

All clouds influence the Earth's radiative budget, with their net radiative forcing being negative. However, high-level clouds warrant special attention due to their atmospheric warming effects. A comprehensive characterization of cirrus requires information on cloud coverage, obtainable from various data types. Active satellite sensors are presently the most accurate source for cirrus data, but their usefulness in climatological studies is limited. On the contrary, passive data, available for the past 40 years with sufficient temporal resolution for climatological research, were not specifically designed for cirrus detection. In this study, we assessed the utility of MODIS standard products for creating a cirrus mask by validating them against CALIOP data. Our objective was to determine if a MODIS product exists that detects cirrus with the same accuracy as CALIOP. Using CALIOP data as the reference, we evaluated six tests for cirrus detection considered in MODIS cloud masking algorithm and their combination (ALL TESTS CONSOLIDATION, ATC). Additionally we applied two ISCCP-originating tests: ISCCP3.6 and ISCCP23 tests. All tests have been applied to MODIS radiances. Study revealed that ATC test was the most effective resulting with the overall accuracy of 72.98 % during daytime and 59.50 % at night (probability of detection: 80.87 % and 25.46 %, false alarm rate of 34.86 % and 6.90 %, and Cohen's kapppa coefficient of 0.46 and 0.19 respectively). However, its effectiveness was notably reduced during nighttime compared to daytime. We conclude that the test is suitable for creating a mask of high-level clouds. [ABSTRACT FROM AUTHOR]

A new two-step method for developing a nanocomposite of polypropylene (PP) decorated with photocatalytically active TiO2 nanoparticles (nTiO2) is proposed. This method involves the low-temperature plasma functionalization of polypropylene followed by the ultrasound-assisted anchoring of nTiO2. The nanoparticles, polymeric substrate, and resultant nanocomposite were thoroughly characterized using nanoparticle tracking analysis (NTA), microscopic observations (SEM, TEM, and EDX), spectroscopic investigations (XPS and FTIR), thermogravimetric analysis (TG/DTA), and water contact angle (WCA) measurements. The photocatalytic activity of the nanocomposites was evaluated through the degradation of methyl orange. The individual TiO2 nanoparticles ranged from 2 to 6 nm in size. The oxygen plasma treatment of PP generated surface functional groups (mainly -OH and -C=O), transforming the surface from hydrophobic to hydrophilic, which facilitated the efficient deposition of nTiO2. Optimized plasma treatment and sonochemical deposition parameters resulted in an active photocatalytic nTiO2/PP system, degrading 80% of the methyl orange under UVA irradiation in 200 min. The proposed approach is considered versatile for the functionalization of polymeric materials with photoactive nanoparticles and, in a broader perspective, can be utilized for the fabrication of self-cleaning surfaces. [ABSTRACT FROM AUTHOR]

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides of varying nominal cerium compositions (x = 0, 0.2, 0.3, and 1) were prepared. The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, ranging from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in the textural properties of the catalysts was noted, which was particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under the two following contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface area in loose contact mode. Notably, the temperatures estimated at 10% and 50% of the conversion (T10 and T50) parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511 °C and 538 °C for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed, a significant relationship emerges between work function values and the formation of oxygen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter that showed a better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered. [ABSTRACT FROM AUTHOR]

At the time when pathogens are developing robust resistance to antibiotics, the demand for implant surfaces with microbe-killing capabilities has significantly risen. To achieve this goal, profound understanding of the underlying mechanisms is crucial. Our study demonstrates that graphene oxide (GO) nano films deposited on stainless steel (SS316L) exhibit superior antibacterial features. The physicochemical properties of GO itself play a pivotal role in influencing biological events and their diversity may account for the contradictory results reported elsewhere. However, essential properties of GO coatings, such as oxygen content and the resulting electrical conductivity, have been overlooked so far. We hypothesize that the surface potential and electrical resistance of the oxygen content in the GO-nano films may induce bacteria-killing events on conductive metallic substrates. In our study, the GO applied contains 52 wt% of oxygen, and thus exhibits insulating properties. When deposited as a nano film on an electrically conducting steel substrate, GO flakes generate a Schottky barrier at the interface. This barrier, consequently, impedes the transfer of electrons to the underlying conductive substrate. As a result, this creates reactive oxygen species (ROS), leading to bacterial death. We confirmed the presence of GO coatings and their hydrolytic stability by using X-ray photoelectron spectroscopy (XPS), μRaman spectroscopy, scanning electron microscopy (SEM), and Kelvin probe force microscopy (KPFM) measurements. The biological evaluation was performed on the MG63 osteoblast-like cell line and two selected bacteria species: S. aureus and P. aeruginosa, demonstrating both the cytocompatibility and antibacterial behavior of GO-coated SS316L substrates. We propose a two-step bactericidal mechanism: electron transfer from the bacteria membrane to the substrate, followed by ROS generation. This mechanism finds support in changes observed in contact angle, surface potential, and work function, identified as decisive factors. By addressing overlooked factors and effectively bridging the gap between understanding and practicality, we present a transformative approach for implant surfaces, combating microbial resistance, and offering new application possibilitie. [ABSTRACT FROM AUTHOR]