Search

Riparian zones are essential to preserve water quality of rivers adjacent to large areas of irrigated agriculture. We used HYDRUS (2D/3D) to quantify the long-term (8 years) influence of crops (almonds, wine grapes and potato-carrot) irrigated with recycled water on water and solute exchange at the Gawler River interface in relation to vegetation buffer widths from 10 to 110 m. We found that under almond and annual horticulture the likely average annual water flow from the irrigated area to the river was nearly twice as much (2.1 and 1.8, respectively) that under wine grapes. The hydraulic exchange at river interface for different irrigated crops was found to be sensitive to the buffer widths. For wine grapes, almonds and annual horticulture, the average annual hydraulic balance reached an equilibrium at 20, 65 and 55 m buffer widths, respectively. Furthermore, for wine grapes, with a 20 m buffer width, the average annual load of salts became negligible. This study shows that buffer widths of 20, 60, and 40 m for irrigated wine grapes, almond, and annual horticulture, respectively, are needed to restrict the migration of salts to the river. Further refinements are possible by incorporating the influence of preferential flow paths, improved water stress response functions, and addressing the data limitations for calibration of the model for solute dynamics.

The historical use and storage of aqueous film-forming foams (AFFF) containing per- and poly-fluoroalkyl substances (PFAS) at a range of sites including airports, defence, and port facilities have resulted in a legacy of contaminated infrastructure such as concrete. Contaminated concrete constitutes an ongoing source of PFAS contamination requiring management to ensure the protection of human health and the environment. In this study, modified Leaching Environmental Assessment Framework (LEAF) and Australian Standard Leaching Procedure (ASLP) were used to examine the leachability of PFAS, specifically, perfluorooctanesulfonate (PFOS), perfluorooctanoic acid (PFOA), perfluorohexanesulfonate (PFHxS) and perfluorohexanoic acid (PFHxA) from AFFF-contaminated concrete collected from an Australian Defence Fire Training Area (FTA). In general, PFAS readily leached from intact contaminated concrete monoliths with the cumulative proportion (%) decreasing in the order: PFHxA (>95%) > PFOS (26-84%) ≈ PFHxS (14-78%) > PFOA (<1-54%). Higher leachability for PFHxA from concrete is consistent with previous findings for solids, however, inconsistent for PFOA with higher retention (lower leachability) in concrete as compared to PFOS. Duration of exposure to water (0.5-48 h) and temperature (25 °C and 50 °C) had little influence on the proportion of PFAS leachability from powdered concrete. A higher proportion of PFAS leached from a <2 mm concrete powder size fraction as compared to 2-20 mm and 20 mm size fractions. This behavior reflects an increase in surface area with decreasing concrete particle size. Reducing the particle size could enhance PFAS removal from waste concrete.

Per- and poly-fluoroalkyl substances (PFASs) are contaminants of emerging concern, yet the understanding of factors that control their leaching and release from contaminated soils remains limited. This study aimed to investigate the impact of dissolved organic carbon (DOC) on the release of PFASs-specifically, perfluorohexane sulfonate (PFHxS), perfluorooctane sulfonate (PFOS), and perfluorooctanoic acid (PFOA)from soils contaminated by aqueous film forming foam (AFFF). Batch aqueous leaching experiments were conducted on AFFF-contaminated soils under alkaline solution conditions (pH 9.5, 10.5, and 12) as it enhances leaching of both PFAS and DOC. Leaching of PFOS was significantly increased under alkaline conditions. Although the leaching of PFAS generally increased with pH, PFOS appeared to be more retained under the very alkaline pH conditions used in this study. At the same solution pH, leaching of PFOS and DOC was less in Ca(OH) 2 than in NaOH. The retention of PFOS under these conditions may be attributable to the shielding of the negative charge of the soil components and colloids (e.g., DOC and clay minerals) in the leachates and/or the screening of negative charges on head groups of PFOS due to the high concentration of divalent cations. Solution chemistry affected desorption of PFOS more than PFHxS and PFOA. The study highlights that the influence of DOC on PFAS leaching and transport can be very complex, and depends on leachate chemistry (e.g., pH and cation type), PFAS chemistry, the magnitude of PFAS contamination and factors that influence the solid:liquid partitioning of organic carbon in soil., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Shervin Kabiri reports financial support was provided by Australian Research Council. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Understanding the sorption behavior of per- and poly-fluoroalkyl substances (PFAS) in soils are essential for assessing their mobility and risk in the environment. Heavy metals often coexist with PFAS depending on the source and history of contamination. In this study, we investigated the effect of heavy metal co-contaminants (Pb 2+ , Cu 2+ and Zn 2+ ) on the sorption of 13 anionic PFAS with different perfluorocarbon chain length (C3-C9) in two soils with different properties. Results revealed that Pb 2+ , Cu 2+ and Zn 2+ had little effect on the sorption of most short-chain compounds, while the presence of these heavy metals enhanced the sorption of long-chain PFAS in two soils. The distribution coefficients (K d ) of several long-chain PFAS linearly increased with increasing concentrations of heavy metal, especially in the presence of Pb 2+ (ΔK d /Δ [Pb 2+ ] > 3 for PFOS and PFNA vs <1 for PFPeS and PFHxS). While several mechanisms may have contributed to the enhancement of sorption of PFAS, the heavy metals most likely contributed through enhanced hydrophobic interactions of PFAS by neutralizing the negative charge of adsorption surfaces in soils and thus making it more favorable for their partitioning onto the solid phase. Moreover, the increase in the concentrations of heavy metals led to a decrease in the pH of the system and promoted sorption of long-chain compounds, especially in soil with lower organic carbon content. Overall, this study provides evidence that the presence of co-existing heavy metal cations in soils can significantly enhance the sorption of long-chain PFAS onto soil, thereby potentially limiting their mobility in the environment., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Wenwen Cai reports financial support was provided by China Scholarship Council., (Copyright © 2023 The Authors. Published by Elsevier B.V. All rights reserved.)

Per- and polyfluoroalkyl substances (PFAS) are now widespread in the environment. Globally, airfields and paved firefighting training surfaces are particularly affected due to extensive use of aqueous film forming foams (AFFF). This PFAS contamination in exposed concrete and asphalt has not been widely addressed. This review focusses on PFAS interaction with concrete and asphalt, traversing extraction, analytical identification/quantification, PFAS fractionation via differential adsorption on organic and inorganic substrates, and reuse options for contaminated concrete and asphalt. A total of 24 knowledge gaps and management challenges for concrete and asphalt characterisation and management have been identified., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Grant Douglas reports financial support was provided by Australian Government Department of Defence., (Crown Copyright © 2023. Published by Elsevier B.V. All rights reserved.)

Removal of per- and polyfluoroalkyl substances (PFASs) from water or their immobilization in soil using carbon-based sorbents is one of the cost-effective techniques. Considering the variety of carbon-based sorbents, identifying the key sorbent properties responsible for PFASs removal from solution or immobilization in the soil can assist in the selection of the best sorbents for management of contaminated sites. This study evaluated the performance of 28 carbon-based sorbents including granular and powdered activated carbon (GAC and PAC), mixed mode carbon mineral material, biochars, and graphene-based materials (GNBs). The sorbents were characterized for a range of physical and chemical properties. PFASs' sorption from an AFFF-spiked solution was examined via a batch experiment, while their ability to immobilize PFASs in soil was tested following mixing, incubation and extraction using the Australian Standard Leaching Procedure. Both soil and solution were treated with 1 % w/w sorbents. Comparing different carbon-based materials, PAC, mixed mode carbon mineral material and GAC were the most effective in sorbing PFASs in both solution and soil. Among the different physical characteristics measured, the sorption of long-chain and more hydrophobic PFASs in both soil and solution was best correlated with sorbent surface area measured using methylene blue, which highlights the importance of mesopores in PFASs sorption. Iodine number was found to be a better indicator of the sorption of short-chain and more hydrophilic PFASs from solution but was found to be poorly correlated with PFASs immobilization in soil for activated carbons. Sorbents with a net positive charge performed better than those with a net negative charge, or no net charge. This study showed that surface area measured by methylene blue and surface charge are the best indicators of sorbent performance with respect to sorption/reducing leaching of PFASs. These properties may be helpful in selecting sorbents for PFASs remediation of soils/waters., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Shervin kabiri reports financial support was provided by The University of Adelaide School of Agriculture Food & Wine. Shervin kabiri reports a relationship with The University of Adelaide School of Agriculture Food & Wine that includes: funding grants., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Immobilisation/stabilisation is one of the most developed and studied approaches for treating soils contaminated with per- and poly-fluoroalkyl substances (PFAS). However, its application has been inhibited by insufficient understanding of the effectiveness of added soil sorbents over time. Herein, we present results on the effectiveness of select carbon-based sorbents, over 4 years (longevity) and multiple laboratory leaching conditions (durability). Standard batch leaching tests simulating aggressive, worst-case scenario conditions for leaching (i.e., shaking for 24-48 h at high liquid/solid ratios) were employed to test longevity and durability of stabilisation in clay-loam and sandy-loam soils historically contaminated with PFAS (2 and 14 mg/kg ∑ 28 PFAS). The different sorbents, which were applied at 1-6% (w/w), reduced leaching of PFAS from the soils to varying degrees. Among the 5 sorbents tested, initial assessments completed 1 week after treatment revealed that 2 powdered activated carbon (PAC) sorbents and 1 biochar were able to reduce leaching of PFAS in the soil by at least 95%. Four years after treatment, the performance of the PAC sorbents did not significantly change, whilst colloidal AC improved and was able to reduce leaching of PFAS by at least 94%. The AC-treated soils also appeared to be durable and achieved at least 95% reduction in PFAS leaching under repetitive leaching events (5 times extraction) and with minimal effect of pH (pH 4-10.5). In contrast, the biochars were affected by aging and were at least 22% less effective in reducing PFAS leaching across a range of leaching conditions. Sorbent performance was generally consistent with the sorbent's physical and chemical characteristics. Overall, the AC sorbents used in this study appeared to be better than the biochars in stabilising PFAS in the long term., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Divina Navarro reports financial support was provided by the Australian Government Department of Defence., (Crown Copyright © 2023. Published by Elsevier Ltd. All rights reserved.)

This paper aims to describe the performance of a soil washing plant (SWP) for remediating a per- and poly-fluoroalkyl substances (PFASs)-contaminated soil with a high clay content (61%). The SWP used both physical and chemical processes; fractionation of the soil particles by size and partitioning of PFASs into the aqueous phase to remove PFASs from the soil. Contaminated water was treated in series with granulated activated carbon (GAC) and ion-exchange resin and reused within the SWP. Approximately 2200 t (dry weight) of PFAS-contaminated soil was treated in 25 batches of 90 t each, with a throughput of approximately 11 t soil/hr. Efficiency of the SWP was measured by observed decreases in total and leachable concentrations of PFASs in the soil. Average removal efficiencies (RE) were up to 97.1% for perfluorocarboxylic acids and 94.9% for perfluorosulfonic acids. REs varied among different PFASs depending on their chemistry (functional head group, carbon chain length) and were independent of the total PFAS concentrations in each soil batch. Mass balance analysis found approximately 90% of the PFAS mass in the soil was transferred to the wash solution and > 99.9% of the PFAS mass in the wash solution was transferred onto the GAC without any breakthrough., Competing Interests: Declaration of Competing Interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Charles Grimison reports a relationship with Ventia Services that includes: employment., (Crown Copyright © 2022. Published by Elsevier B.V. All rights reserved.)

Disinfection by-products (DBPs) are formed through the disinfection of water containing precursors such as natural organic matter or anthropogenic compounds (e.g., pharmaceuticals and pesticides). Due to the ever increasing use of plastics, elastomers, and other polymers in our daily lives, polymer-based materials (PBMs) are detected more frequently and at higher concentrations in water and wastewater. The present review provides a comprehensive and systematic analysis of the contribution of PBMs - including elastomers, tire waste, polyelectrolytes, and microplastics - as precursors of DBPs in water and wastewater. Literature shows that the presence of PBMs can lead to the leaching of dissolved organic matter (DOM) and subsequent formation of DBPs upon disinfection in aqueous media. The quantity and type of DBPs formed strongly depends on the type of polymer, its concentration, its age, water salinity, and disinfection conditions such as oxidant dosage, pH, temperature, and contact time. DOM leaching from elastomers and tire waste was shown to form N-nitrosodimethylamine up to concerning levels of 930 ng/L and 466,715 ng/L, respectively upon chemical disinfection under laboratory conditions. Polyelectrolytes can also react with chemical disinfectants to form toxic DBPs. Recent findings indicate trihalomethanes formation potential of plastics can be as high as 15,990 µg/L based on the maximum formation potential under extreme conditions. Our analysis highlights an overlooked contribution of DOM leaching from PBMs as DBP precursors during disinfection of water and wastewater. Further studies need to be conducted to ascertain the extent of this contribution in real water and wastewater treatment plants., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Spills of hydraulic fracturing (HF) fluids and of produced water during unconventional gas extraction operations may cause soil contamination. We studied the degradation and microbial toxicity of selected HF chemical components including two biocides (methylisothiozolinone- MIT, chloromethylisothiozolinone- CMIT), a gel-breaker aid (triethanolamine -TEA), and three geogenic chemicals (phenol, m-cresol and p-cresol) in ultrapure water, HF fluid and produced water in five different soil types (surface and subsurface soils). The degradation of the two biocides (in soils treated with HF fluid or ultrapure water) and of the three geogenic chemicals (in soils treated with produced water) was rapid (in all cases DT 50 values < 2 days in surface soils). In contrast, the loss of TEA was much slower in soils, especially in those treated with HF fluid (DT 50  > 30 days). Sorption coefficients (K oc in L/Kg) in these soils ranged from 71 to 733 for TEA, 64-408 for MIT and 11-72 for CMIT. In terms of soil microbial toxicity, exposure to HF fluid and produced water reduced microbial respiration, albeit temporarily. The overall microbial activities in surface soils contaminated with produced water had fully recovered in most soils. In contrast, the HF fluid addition to soils completely inhibited the nitrification in all soils, with little recovery over the 60 day experimental period. In the case of produced water exposure, three out of five surface soils showed complete recovery in nitrification during the study period. The functional genes for nitrogen fixation (nifH) and carbon cycling (GA1) and microbial community composition (16 S rRNA) were significantly affected by HF fluid in some soils. Overall, the study shows that the HF fluid can have significant detrimental impact on soil microbial functions, especially on nitrogen cycling. More work is needed to identify the exact cause of microbial toxicity in soils contaminated with HF fluid., (Crown Copyright © 2022. Published by Elsevier Ltd. All rights reserved.)

This study investigated the mobilization of a wide range of per- and polyfluoroalkyl substances (PFASs) present in aqueous film-forming foams (AFFFs) in water-saturated soils through one-dimensional (1-D) column experiments with a view to assessing the feasibility of their remediation by soil desorption and washing. Results indicated that sorption/desorption of most of the shorter-carbon-chain PFASs ( C ≤ 6) in soil reached greater than 99% rapidly─after approximately two pore volumes (PVs) and were well predicted by an equilibrium transport model, indicating that they will be readily removed by soil washing technologies. In contrast, the equilibrium model failed to predict the mobilization of longer-chain PFASs ( C ≥ 7), indicating the presence of nonequilibrium sorption/desorption (confirmed by a flow interruption experiment). The actual time taken to attain 99% sorption/desorption was up to 5 times longer than predicted by the equilibrium model (e.g., ∼62 PVs versus ∼12 PVs predicted for perfluorooctane sulfonate (PFOS) in loamy sand). The increasing contribution of hydrophobic interactions over the electrostatic interactions is suggested as the main driving factor of the nonequilibrium processes. The inverse linear relationship ( R 2 = 0.6, p < 0.0001) between the nonequilibrium mass transfer rate coefficient and the Freundlich sorption coefficient could potentially be a useful means for preliminary evaluation of potential nonequilibrium sorption/desorption of PFASs in soils.

The effect of soluble cations on sorption in soils of a range of anionic PFAS is not well studied. We investigated the role of three common cations (Na + , Ca 2+ , and Mg 2+ ) at varying solution concentrations on the sorption coefficients (K d ) of 18 anionic PFAS in two contrasting soils. The effective charge of the soil suspension (Zeta potential) became less negative as the concentration of these cations increased in the soil solutions. Perfluorinated compounds showed greater sorption than polyfluorinated compounds, with sulfonates of comparable chain lengths showing higher sorption than the carboxylates. We observed that the K d values of several PFAS in the two soils were positively correlated with the concentration of cations in solution, especially in the presence of polyvalent cations (Ca 2+ and Mg 2+ ). The changes in sorption with cation concentration were more prominent for long-chain PFAS, with C > 10 PFAS being completely removed from solution at higher cation concentrations. The emerging PFAS (replacement compounds GenX and ADONA) showed negligible or little sorption (K d  < 0.6 L/kg). While several mechanisms contribute towards sorption of PFAS in the presence of cations, we conclude that the primary effect of cations is through screening of negative charges on head groups of PFAS and reorientation of molecules at the interface between organic matter surfaces and soil solution as well as charge neutralisation at soil solid surface. Screening of negative charges allows for greater hydrophobic interaction between hydrophobic tails of PFAS and soil surfaces resulting in greater sorption. Increasing cation concentrations in soil solutions could thus reduce mobility of PFAS through a soil profile., Competing Interests: Declaration of competing interest There are no conflicts of interest to declare., (Copyright © 2022 The Authors. Published by Elsevier B.V. All rights reserved.)

Soil contaminated with aqueous film-forming foams (AFFFs) containing per- and polyfluoroalkyl substances (PFASs) at firefighting training sites has become a major concern worldwide. To date, most studies have focused on assessing soil-water partitioning behavior of PFASs and the key factors that can affect their sorption, whereas PFASs leaching from contaminated soils have not yet been widely investigated. This study evaluated the leaching and desorption of a wide range of PFASs from twelve contaminated soils using the Australian Standard Leaching Procedure (ASLP), the U.S. EPA Multiple Extraction Procedure (MEP), and Leaching Environmental Assessment Framework (LEAF). All three leaching tests provided a similar assessment of PFAS leaching behavior. Leaching of PFASs from soils was related to C-chain lengths and their functional head groups. While short-chain (CF 2 ≤ 6) PFASs were easily desorbed and leached, long-chain PFASs were more difficult to desorb. PFASs with a carboxylate head group were leached more readily and to a greater extent than those with a sulfonate or sulfonamide head group. Leaching of long-chain PFASs was pH-dependent where leaching increased at high pH, while leaching of short-chain PFASs was less sensitive to pH. Comparing different leaching tests showed that the results using the alkaline ASLP were similar to the cumulative MEP data and the former might be more practical for routine use than the MEP. No single soil property was adequately able to describe PFAS leaching from the soils. Overall, the PFAS chemical structure appeared to have a greater effect on PFAS leaching from soil than soil physicochemical properties.

Nanopesticides are not only in an advanced state of research and development but have started to appear on the market. Industry and regulatory agencies need a consolidated and comprehensive framework and guidance for human health risk assessments. In this perspective we develop such a comprehensive framework by exploring two case studies from relevant product types: an active ingredient delivered with a nanocarrier system, and a nanoparticle as an active ingredient. For a nanocarrier system, three entities are tracked during the assessment: the nanocarrier-active ingredient complex, the empty nanocarrier remaining after the complete release of the active ingredient, and the released active ingredient. For the nanoparticle of pure active ingredient, only two entities are relevant: the nanoparticle and the released ions. We suggest important adaptations of the existing pesticide framework to determine the relevant nanopesticide entities and their concentrations for toxicity testing. Depending on the nature of the nanopesticides, additional data requirements, such as those pertaining to durability in biological media and potential for crossing biological barriers, have also been identified. Overall, our framework suggests a tiered approach for human health risk assessment, which is applicable for a range of nanopesticide products to support regulators and industry in making informed decisions on nanopesticide submissions. Brief summaries of suitable methods including references to existing standards (if available) have been included together with an analysis of current knowledge gaps. Our study is an important step towards a harmonized approach accepted by regulatory agencies for assessing nanopesticides., (© 2021. Springer Nature Limited.)

This study investigated the potential aging and plant bioaccumulation of three perfluoroalkyl acids (PFAAs), perfluorosulphonic acid (PFOS), perfluorooctanoic acid (PFOA) and perfluorohexanesulphonic acid (PFHxS) in 20 soils over a six-month period. Sorption coefficients (Log K d ) ranged from 0.13-1.28 for PFHxS, 0.17-1.06 for PFOA and 0.98-2.03 for PFOS, respectively, and bioaccumulation factors (Log BAFs) ranged from 0.29-1.24, 0.22-1.46 and 0.05-0.65 for PFHxS, PFOA and PFOS, respectively. Over the six-month period, K d values significantly increased for PFHxS and PFOA but the magnitude of the increase was very small and did not translate into differences in plant PFAA-concentrations between aged and freshly spiked treatments. The K d and BAF values were modelled by multiple linear regression (MLR) to soil physico-chemical properties and by partial least squares regression to soil spectra acquired by mid-infrared spectroscopy (DRIFT-PLSR). Modelling of each PFAA was influenced by different soil properties, including organic carbon, pH, CEC, exchangeable cations (Ca 2+ , Mg 2+ , Na + and K + ) and oxalate extractable Al. BAF values were not strongly correlated to any soil property but were inversely correlated to K d values. Our results indicate that limited aging occurred in these soils over the six-month period., (Copyright © 2020 Elsevier B.V. All rights reserved.)

The aim of this study was to assess the soil-water partitioning behavior of a wider range of per- and polyfluoroalkyl substances (PFASs) onto soils covering diverse soil properties. The PFASs studied include perfluoroalkyl carboxylates (PFCAs), perfluoroalkane sulfonates (PFSAs), fluorotelomer sulfonates (FTSs), nonionic perfluoroalkane sulfonamides (FASAs), cyclic PFAS (PFEtCHxS), per- and polyfluoroalkyl ether acids (GenX, ADONA, 9Cl-PF3ONS), and three aqueous film-forming foam (AFFF)-related zwitterionic PFASs (AmPr-FHxSA, TAmPr-FHxSA, 6:2 FTSA-PrB). Soil-water partitioning coefficients (log  K d values) of the PFASs ranged from less than zero to approximately three, were chain-length-dependent, and were significantly linearly related to molecular weight (MW) for PFASs with MW > 350 g/mol ( R 2 = 0.94, p < 0.0001). Across all soils, the K d values of all short-chain PFASs (≤5 -CF2- moieties) were similar and varied less (<0.5 log units) compared to long-chain PFASs (>0.5 to 1.5  log units) and zwitterions AmPr- and TAmPr-FHxSA (∼1.5 to 2 log units). Multiple soil properties described sorption of PFASs better than any single property. The effects of soil properties on sorption were different for anionic, nonionic, and zwitterionic PFASs. Solution pH could change both PFAS speciation and soil chemistry affecting surface complexation and electrostatic processes. The K d values of all PFASs increased when solution pH decreased from approximately eight to three. Short-chain PFASs were less sensitive to solution pH than long-chain PFASs. The results indicate the complex interactions of PFASs with soil surfaces and the need to consider both PFAS type and soil properties to describe mobility in the environment.

Urbanisation will be one of the 21st century's most transformative trends. By 2050, it will increase from 55% to 68%, more than doubling the urban population in South Asia and Sub-Saharan Africa. Urbanisation has multifarious (positive as well as negative) impacts on the wellbeing of humans and the environment. The 17 UN Sustainable Development Goals (SDGs) form the blueprint to achieve a sustainable future for all. Clean Water and Sanitation is a specific goal (SDG 6) within the suite of 17 interconnected goals. Here we provide an overview of some of the challenges that urbanisation poses in relation to SDG 6, especially in developing economies. Worldwide, several cities are on the verge of water crisis. Water distribution to informal settlements or slums in megacities (e.g. >50% population in the megacities of India) is essentially non-existent and limits access to adequate safe water supply. Besides due to poor sewer connectivity in the emerging economies, there is a heavy reliance on septic tanks, and other on-site sanitation (OSS) system and by 2030, 4.9 billion people are expected to rely on OSS. About 62-93% of the urban population in Vietnam, Sri Lanka, the Philippines and Indonesia rely on septic tanks, where septage treatment is rare. Globally, over 80% of wastewater is released to the environment without adequate treatment. About 11% of all irrigated croplands is irrigated with such untreated or poorly treated wastewater. In addition to acute and chronic health effects, this also results in significant pollution of often-limited surface and groundwater resources in Sub-Saharan Africa and Asia. Direct and indirect water reuse plays a key role in global water and food security. Here we offer several suggestions to mitigate water and food insecurity in emerging economies., Competing Interests: Declaration of competing interest The authors along with all co-authors are in agreement for the work being peer reviewed and possibly published and we have no undeclared competing financial interests or conflicts of interest., (Crown Copyright © 2020. Published by Elsevier B.V. All rights reserved.)

The sorption of three perfluoroalkyl substances (PFASs), namely perfluorooctane sulfonic acid (PFOS), perfluorooctanoic acid (PFOA) and perfluorohexane sulfonic acid (PFHxS), was determined in 19 coastal sediments. There are currently limited data on the sorption behaviour of these chemicals in marine or estuarine sediments and the properties controlling their sorption have not been well established. The median average PFOS K d value (30.4 L/kg) was >8 times that for PFOA (3.3 L/kg) and PFHxS (2.8 L/kg). Highly significant (P < .001) linear relationships were found between values for sorption coefficients (K d ) for all three chemicals (PFOS, PFOA and PFHxS) to the estuarine sediments and organic carbon (OC) content with r 2 values ranging from 0.87 to 0.91. The nature of the constituents of OC was determined by nuclear magnetic resonance (NMR) for a subset (10) of the sediments to assess whether the strong relationship between sorption and OC was due solely to an increasing amount of OC or to particular OC fractions. The NMR analysis could not provide strong evidence for one OC fraction type explaining the variation in sorption of the three PFASs. Further investigation using partial least squares of the whole spectra also did not show any particular OC components could explain the K d variation. This data suggests that variation in sorption in these sediments was primarily due to the varying OC content and not its chemistry., Competing Interests: Declaration of competing interest All authors declare there is no conflict of interest., (Crown Copyright © 2020. Published by Elsevier B.V. All rights reserved.)

We studied sorption potential for a range of herbicides using eleven waste materials (mill muds) containing organic matter (47.6 to 65.1%) produced by sugar mills and applied as soil conditioners by farmers. Sorption/desorption behaviour of five herbicides commonly used in sugarcane production (imazapic, atrazine, hexazinone, diuron and metribuzin) was studied on these mill muds, as is and after adding these to three soils at different rates (5-25%, dry weight basis). All mill muds had significant sorption capacity, especially for diuron, atrazine and metribuzin which was 6 to 26 times higher than the soil with 3.5% organic carbon (OC). Generally, sorption of the five herbicides assessed in all mill muds followed the order diuron > atrazine = metribuzin > hexazinone = imazapic. Eight out of 11 mill muds had similar sorption capacity for any given herbicides. Amending soils with selected mill muds significantly enhanced their sorption efficiency, depending on the rate of application especially in soil with low OC. Generally, application of mill muds at 5% w/w or 40 tons/ha increased sorption of studied herbicides by 2 to 10 folds. Soil amendment with mill muds also reduced the rate and extent of desorption of herbicides- especially mobile herbicides like metribuzin. Nearly 79% release of metribuzin was observed after three desorption steps in amended soil (at 5% w/w), whereas in unamended soil, 100% of metribuzin was released during first desorption step. The study demonstrates that wastes produced by sugar mills may have recycling use in enhancing the retention of mobile herbicides in soils with low OC content., Competing Interests: Declaration of competing interest The authors have no competing financial interests or conflicts of interest., (Crown Copyright © 2020. Published by Elsevier B.V. All rights reserved.)