Search

The encapsulation of drugs within mesoporous silica (MS) has for several years been a subject of research. Previous studies proposed that drug loadings up to the monomolecular loading capacity (MLC) are the optimal choice for maintaining the drug in an amorphous form, whereas filling the pores above the monolayer and up to the pore filling capacity (PFC) may introduce some physical instabilities. The aim of this study was to assess the effect of drug loading in MS-based amorphous formulations on the stability of the amorphous form of the drug as well as the dissolution. In particular, the following drug loadings were investigated: below MLC, at MLC, between MLC and PFC and at PFC. The drug-loaded MS formulations were analyzed directly after preparation and after 18 months of storage under accelerated conditions (40 °C in both dry and humid conditions). The MLC and PFC for the drug celecoxib (CEL) on the MS ParteckSLC500 (SLC) were determined at 33.5 wt.% and 48.4 wt.%, respectively. This study found that SLC can effectively preserve the amorphous form of the drug for 18 months, provided that the loading is below the PFC (<48.4 wt.%) and no humidity is present. On the other hand, drug loading at the PFC showed recrystallization even when stored under dry conditions. Under humid conditions, however, all samples, regardless of drug loading, showed recrystallization upon storage. In terms of dissolution, all freshly prepared formulations showed supersaturation. For drug loadings below PFC, a degree of supersaturation (DS) around 15 was measured before precipitation was observed. For drug loadings at PFC, the DS was found to be lower and only 6-times compared to the crystalline solubility. Lastly, for those samples that remained amorphous during storage for 18 months, the release profiles were found to be the same as the freshly loaded samples, with similar Cmax, Tmax and dissolution rate.

Successful oral delivery of liposomes requires formulations designed to withstand harsh gastrointestinal conditions, e.g., by converting to solid-state followed by loading into gastro-resistant delivery devices. The hypothesis was that the use of dextran-trehalose mixtures for spray drying would improve the rehydration kinetics of dried liposomes. The objectives were to determine the protective capacity of trehalose-dextran dehydration precursors and to increase the concentration of liposomes in the dry formulation volume. The study successfully demonstrated that 8.5% dextran combined with 76.5% trehalose protected CAF®04 liposomes during drying, with the liposome content maintained at 15% of the dry powder. Accordingly, the rehydration kinetics were slightly improved in formulations containing up to 8.5% dextran in the dry powder volume. Additionally, a 2.4-fold increase in lipid concentration (3 mM vs 7.245 mM) was achieved for spray dried CAF®04 liposomes. Ultimately, this study demonstrates the significance of trehalose as a primary carrier during spray drying of CAF®04 liposomes and highlights the advantage of incorporating small amounts of dextran to tune rehydration kinetics of spray-dried liposomes.

In this study, a new method to determine the solubility of crystalline drugs in (amorphous) polymers is proposed. The method utilizes annealing of supersaturated amorphous solid dispersions to achieve equilibrium between dissolved and recrystallized drug. By measuring the enthalpy of melting and mixing (Hm+mix) of the recrystallized drug, the equilibrium solubility of the drug in the polymer at the annealing temperature is determined. The equilibrium solubilities at these elevated temperatures were used to extrapolate to room temperature using the Flory-Huggins model. The new Hm+mix method showed solubility predictions in line with the melting point depression (MPD) and recrystallization (RC) methods for indomethacin (IMC) -polyvinylpyrrolidone (PVP). For IMC-hydroxypropyl methylcellulose (HPMC), the MPD method plateaued rapidly, leaving only one usable data point. The RC method showed large variations in the solubility predictions possibly due to a narrow glass transition temperature (Tg) window or inaccurate Tg determination. In contrast, the new Hm+mix method showed robust solubility prediction over the entire annealing temperature range with low variation and narrow error margins after extrapolation for both drug-polymer systems. The new Hm+mix method was able to accurately determine the drug-polymer solubility of IMC-HPMC, showing promise as a new tool to determine the solubility of problematic drug-polymer systems.

This study investigated the ability of in situ amorphisation using microwave irradiation in order to prepare highly supersaturated ASDs, i.e. ASDs with drug loads higher than the saturation solubility in the polymer at ambient temperature. For this purpose, compacts containing the crystalline drug celecoxib (CCX) and polyvinylpyrrolidone (PVP), polyvinylpyrrolidone—vinyl acetate copolymer (PVP/VA), or polyvinyl acetate (PVAc), were prepared at drug loads between 30 and 90 % w/w. Sodium dihydrogen phosphate (NaH2PO4) monohydrate was included in all compacts, as a source of water, to facilitate the dielectric heating of the compacts upon dehydration during microwave irradiation. After processing, the samples were analysed towards their solid state using X-ray powder diffraction (XRPD) and modulated differential scanning calorimetry (mDSC). Complete amorphisation of CCX was achieved across all the investigated polymers and with a maximal drug load of 90, 80, and 50 % w/w in PVP, PVP/VA, and PVAc, respectively. These drug loads corresponded to a 2.3-, 2.4-, and 10.0-fold supersaturation in the investigated polymers at ambient temperature. However, dissolution experiments with the in situ prepared ASDs in fasted state simulated intestinal fluid (FaSSIF), showed a lower initial drug release (0–2 h) compared to equivalent physical mixtures of crystalline CCX and polymers or crystalline CCX alone. The lower drug release rate was explained by the fusion of individual drug and polymer particles during microwave irradiation and, subsequently, a lack of disintegration of the monolithic ASDs. Nevertheless, supersaturation of CCX in FaSSIF was achieved with the in situ amorphised ASDs with PVP and PVP/VA, albeit only after 3–24 h. Overall, the present study confirmed that it is feasible to prepare supersaturated ASDs in situ. However, in the current experimental setup, the monolithic nature of the resulting ASDs is considered a limiting factor in the prac

The rate at which oral tobacco-derived nicotine (OTDN) and snus pouches release nicotine into saliva is crucial to determine product performance. As no standardized method is available for this purpose, this study sought to develop a biorelevant dissolution method that could both discriminate between different products and predict in vivo behavior. Using a mu DISS Profiler (TM) as a surrogate for the US Pharmacopoeia standard apparatuses and a custom-made sinker, nicotine release from an OTDN pouch product (ZYN(R) Dry Smooth) and a snus product (General(R) Pouched Snus White Portion Large) was determined in biorelevant volumes (10 mL) of artificial saliva. In addition, nicotine extraction in vivo was measured for both products. Strikingly, the method showed distinct dissolution curves for OTDN and snus pouches, and the nicotine release observed in vitro did not significantly differ from the nicotine extracted in vivo. The custom-made sinker was designed to accommodate both loose and pouched oral tobacco/nicotine products, and thus the proposed in vitro dissolution method is suitable to assess nicotine release from OTDN and snus pouches. Apart from providing individual dissolution curves, the method was also able to predict in vivo nicotine extraction. Thus, this method could serve as a (biorelevant) monograph for product equivalence studies.