Search

This study reveals the modification of the surface area of natural zeolite Clinoptilolite (CLN) by implementing the ion exchange method. The ammonium chloride cation exchange method was adopted and was followed by calcination at 450 °C for 5 h. This procedure helps to increase the surface area of CLN and also enhances its adsorption efficiency. The modifications of the CLN were confirmed by Fourier-transform infrared (FT-IR) spectroscopy and X-ray diffraction (XRD) analysis. The efficiency and adsorption capacity of the modified CLN were determined by the adsorption of a Rhodamine B (Rh B) dye from an aqueous medium. The comparative analysis of the adsorption efficiency of raw CLN and the modified CLN revealed an enhanced adsorption of Rh B by the modified CLN at pH = 10. For desorption, different solvents were used. The results showed good desorption in ethanol and methanol, and poor desorption in acidic (HCl) and basic (NaOH) solutions. The kinetic study of the adsorption of Rh B by the modified CLN helped us to conclude that the adsorption follows a pseudo-second-order kinetics. For the surface study and to understand the mechanism of adsorption, several isotherm models were applied to the adsorption data at equilibrium. The data showed consistency with the Freundlich adsorption isotherm confirming that the process took place at its heterogeneous surface. The experimentally calculated adsorption capacity of the modified CLN was 2.81 mg g−1, showing a comparable value to certain other common adsorbents. Therefore, the modified CLN may also be considered a cost-effective and promising adsorbent for the removal of Rh B dye from wastewater. [ABSTRACT FROM AUTHOR]

The removal of water pollutants by photocatalysis is a promising technique, mainly due to its environmentally friendly and sustainable nature. In this study, the degradation of a recalcitrant organic pollutant, malachite green (MG), was investigated in water by a microstructured silver oxide photocatalyst. The silver oxide (Ag2O) microparticles (MPs) were synthesized by a low-cost, green method, mediated by green tea leaves extract. The surface, morphological and optical properties of the synthesized Ag2O MPs were determined by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, X-ray diffraction (XRD) analysis, Fourier transform infrared (FTIR) spectroscopy, and ultraviolet-visible (UV-visible) spectrophotometry. The synthesized Ag2O MPs showed good photoactivity, represented by 83% degradation of malachite green (MG) ([C]0 = 0.4 mM, Ag2O loading = 0.1 g L−1) at neutral pH, in 3 h. Persulfate ions (PS) showed a strong synergistic effect on the efficiency of solar/Ag2O photocatalysis, represented by complete MG removal in 15 min, in the presence of 1.6 mM PS. The results revealed that solar/Ag2O, particularly solar/Ag2O/PS photocatalysis is a promising method for the elimination of toxic organic pollutants, such as malachite green, from the water environment. [ABSTRACT FROM AUTHOR]

Oxidation of the iodide ion is an important facet of the solar cells such as perovskite solar cells and dye‐sensitized solar cells. The rate of reaction undoubtedly depends upon several factors. Such parameters include reaction media, electrolyte, and the nature of solvents, and electrolyte. If these factors are optimized then the rate of the reaction can be controlled and could be used to get the maximum benefit out of it such as economically and industrially cost‐effective uses of the reaction and globally environmentally benign. We studied the kinetics of the oxidation of the iodide ion in the binary solvent system that consisted of 10% (v/v) tertiary butyl alcohol and water. The transition metal complex such as dicyanobis(phenanthroline)iron(III) oxidizes the iodide ion spontaneously without any external triggering with a fast rate at 293 ± 1 K. The reaction was probed under the pseudo–first‐order condition with an excess concentration of the iodide ion over dicyanobis(phenanthroline)iron(III) at 0.06 M ionic strength. The reaction was observed independent of the concentration of dicyanobis(phenanthroline)iron(III), that is, the zero order and third order with respect to the iodide ion in the selected solvent system. An overall third‐order was observed for the redox reaction. The value of the multiplication product of the molar absorptivity (ɛ), path length of the cuvette (b), and overall rate constant (k) was deduced to be 1.59 × 106 M−3 s−1. The observed zero‐order rate constant of the reaction was increased by the fractional (1.5) power of the concentration of protons in the excess concentration of acid 1 mM to 0.1 M. The multiplication product of ɛ⋅b to the fractional order rate constant (k′) was found 0.773 M−1.5 s−1 that confirms protonation of triiodide in acidic‐10% (v/v) tertiary butyl alcohol‐water. The effect of ionic strength showed a similar impact in different compositions of solvents such as 5, 10, and 20% (v/v) tertiary butyl alcohol‐water. The observed zero‐order rate constant was decreased upon increasing the ionic strength in each medium consisting of the binary solvent system. [ABSTRACT FROM AUTHOR]

The redox reaction between dicyanobis(bipyridine)iron(III) and iodide ion follows first‐order kinetics in 10% (v/v) tertiary butyl alcohol‐water. The reaction was found first and zero order in iodide and dicyanobis(bipyridine)iron(III), respectively, at 0.06 M ionic strength and 293 ± 1 K. The thermodynamic parameters of activation such as EA (16.07 kJ mol−1), A (1 × 10−4 M s−1), ΔH# (13.6 kJ mol−1), ΔS# (−329.81 J K−1 mol−1), and ΔG# (90.1 kJ mol−1) were determined. The effect of the ionic strength on the rate constant leads to recognizing the stabilization or destabilization of the transition state complex that forms during the rate‐determining step of the reaction. The value of the zero‐order rate constant was decreased with increasing ionic strength that yielded a negative value of the slope in each binary and ternary solvent systems. This negative sign refers to the electron transfer between opposite charge carriers such as [FeIII(bpy)2(CN)2]+ and I− during the rate‐determining step. The destabilization of the transition state complex is surfaced by the increasing slope, that is, 5 < 10 < 15% (v/v) tertiary butyl alcohol‐water with a gradual decrease in the rate constant. However, its stability emerges by relatively small values of the slope in 17.5 < 25 ≤ 30% (v/v) tertiary butyl alcohol‐water and 8:2:90 < 6:4:90% (v/v) dioxane: tertiary butyl alcohol: water with reasonably fast rate of reaction. [ABSTRACT FROM AUTHOR]

We synthesized the novel histidine complex of uranium(IV). A 1:3 mole ratio was found between metal and ligand by the mole ratio method, while -NH2 and -COO- groups of histidine behave as coordinating sites. The IR spectra confirmed the lone pair donating or coordinating sites. The elemental analysis confirmed the stoichiometry. The bathochromic shift with an increase in the optical density in the UV-Visible range indicated that the compound and its central metal ion hold uniform electronic charge distribution. The electrochemical results indicated a quasi-reversible (neither completely reversible nor completely irreversible) oxidation of the complex to its uranium(V) product at the platinum working electrode. The quasi-reversible process shows a comparatively slow electron transfer (ET) rate with the heterogeneous electron transfer rate constant 'ks' (3.4 × 10-4 cm s-1) at 50 mV s-1 and 305 ± 0.5 K. The kinetics such as diffusion and charge transfer lead the reaction with an ECE (electrochemical-chemical-electrochemical) mechanism. The thermodynamic parameters of activation such as ΔH*; 4.257 kJ mol-1, ΔS*; -2.519 × 10-3 J mol-1 K-1 and ΔG* 4.26 kJ mol-1 helped to propose an associative mechanism of the electron transfer at the platinum working electrode. [ABSTRACT FROM AUTHOR]

The use of indigenous natural materials and their modification toward fruitful application is one of the important subjects. Thermal modification of Rice Husk at 400 oC resulted into Rice Husk Char (RHC) which was chemically modified with KOH and was labeled as KOH Modified Rice Husk Char (KMRHC). Both RHC and KMRHC were characterized by using, Fourier transformed infrared (FTIR), scanning electron microscopy (SEM), energy dispersive X-rays (EDX) and X-ray diffraction (XRD) before and after their use as adsorbents. The prepared material was applied for the removal of toxic dyes, Direct Blue (DB) and Titan Yellow (TY) from aqueous media. The maximum adsorption capacity of DB and TY dyes on KMRHC were inspected as 30.9 mg/g and 28.6 mg/g, respectively at pH 4 using initial dye concentrations of 80 mg/L containing 2500 mg/L of the adsorbent dose with agitation speed of 240 rpm at 303 K. At the same experimental conditions the highest percentage removal of DB and TY on the adsorbent were observed as 96.6% and 89.3%, respectively. Thermodynamics studies of the adsorption of DB and TY dyes on KMRHC inferred for exothermic and spontaneous process. The value of ΔS is negative which suggested that randomness decreases at the interface of adsorbent-adsorbate during the adsorption. The kinetics study indicated that the experimental data of the adsorption process for both dyes, best fits to pseudo-second order kinetic model. The equilibrium data was tested on Langmuir, Freundlich and Temkin adsorption isotherm models. It was observed that the data are best fit to the Langmuir isotherm model (R2 > 0.99), which suggested that the adsorption process is dominated by chemisorption approach. The overall results suggest that various parameters of the adsorption process were not only affected by the variation in experimental conditions but also by the chemical structure of the adsorbate molecules for the same adsorbent. [ABSTRACT FROM AUTHOR]

The present study is focused on the thermal decomposition of Levofloxacin in the absence and presence of different excipients (sodium starch glycolate, magnesium stearate, microcrystalline cellulose and lactose using Thermogravimetry (TG). Fourier Transform Infra Red Spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC) were used to study the possible drug – excipient interaction. It has been shown that the interaction of the first three excipients (sodium starch glycolate, magnesium stearate, and microcrystalline cellulose) with Levofloxacin is physical in nature. Lactose was shown to decrease the degradation temperature to a maximum extent. This indicates a strong chemical interaction between the drug and lactose. The activation energies in the former case were found almost similar but deviated considerably in the latter case. [ABSTRACT FROM AUTHOR]

Abstract: The pyrolysis behavior of polyvinyl chloride (PVC) in the presence of commercially available oxides catalysts was investigated using thermogravimetry. The pyrolysis proceeded under a heating rate of 5°C/min in the temperature range of 200–650°C. The thermogravimetric properties in terms of reduction in maximum degradation temperature and percent conversion were studied. The silica gel mesoporous catalyst, with a greater pore size and surface area, was found to be the most active materials in terms of reduction in maximum degradation temperature and increase in percent conversion. The alumina acidic, silica ppt, and alumina neutral catalysts also showed good results; however, their effects were less pronounced as compared to silica gel. The effects of these different catalysts show that surface area, pore size, and number of acidic sites are found to be the major factors for the energy efficient degradation of polymers. [ABSTRACT FROM AUTHOR]

In this study low density polyethylene (LDPE) has been studied by thermogravimetric analysis (TGA) using commercially available oxides as catalysts. TGA experiments were used to evaluate the activity of different catalysts on low density polyethylene (LDPE) degradation and to study the effect in terms of type and amount of catalyst used. All the catalysts used improved the pyrolysis of LDPE. The reaction rates were found to increase with increase in amount of catalyst. Among the catalysts used, alumina acidic active catalyst performed better at all four fractions. Moreover, alumina acidic active reduced weight loss temperature better than others tested catalysts. The effect of alumina neutral catalyst on the pyrolysis of LDPE is less pronounced due to its small surface area and pore size. The effect of these catalysts showed that surface area, number of acidic sites and pore size were found as the key factors for the energy efficient degradation of polymers. [ABSTRACT FROM AUTHOR]

The present study is aimed at the synthesis and exploring the efficiency of a novel activated carbon incorporated polyindole (AC@PIN) composite for adsorptive removal of Malachite Green (MG) dye from aqueous solution. An AC@PIN hybrid material was prepared by in situ chemical oxidative polymerization. The physico-chemical characteristics of the AC@PIN composite were assessed using Fourier-transform infrared spectrometer, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, ultraviolet visible spectroscopy, and determination of point of zero charge (pHPZC). A series of adsorption studies was conducted to evaluate the influence of operational parameters such as pH, contact time, initial dye concentration, AC@PIN dosage, and temperature on dye adsorption behavior of developed composite. A maximum dye removal percentage (97.3%) was achieved at the pH = 10, AC@PIN dosage = 6.0 mg, initial dye concentration 150 mg L−1, and temperature = 20 °C. The kinetic studies demonstrated that the adsorption of MG on AC@PIN followed pseudo-second-order model (R2 ≥ 0.99). Meanwhile, Langmuir isotherm model was founded to be the best isotherm model to describe the adsorption process. Finally, the recyclability test revealed that the composite exhibits good recycle efficiency and is stable after 5 cycles. The obtained results suggest that AC@PIN composite could be a potential candidate for the removal of MG from wastewater. [ABSTRACT FROM AUTHOR]

Electrocatalytic materials offer numerous benefits due to their wide range of applications. In this study, a polyol technique was used to synthesize PdNi nanoparticles (NPs) with different percent atomic compositions (Pd = 50 to 90%) to explore their catalytic efficiency. The produced nanoparticles were characterized using X-ray diffraction (XRD) and electrochemical investigations. According to XRD measurements, the synthesized NPs were crystalline in nature, with crystallite sizes of about 2 nm. The electrochemical properties of the synthesized NPs were studied in alkaline solution through a rotating ring-disk electrode (RRDE) technique of cyclic voltammetry. The PdNi nanoparticles supported on carbon (PdNi/C) were used as electrocatalysts and their activity and stability were compared with the homemade Pd/C and Pt/C. In alkaline solution, PdNi/C electrocatalysts showed improved oxygen reduction catalytic activity over benchmark Pd/C and Pt/C electrocatalysts in all composition ratios. Furthermore, stability experiments revealed that PdNi 50:50 is more stable in alkaline solution than pure Pd and other PdNi compositions. [ABSTRACT FROM AUTHOR]

In this study palladium-nickel (Pd-Ni) nanoparticles supported on carbon and cerium oxide (Pd-Ni/AC-CeO2) were synthesized by a transfer phase method and characterized by scanning electronic microscopy (SEM), X-ray diffraction (XRD), and energy-dispersive X-ray spectroscopy (EDX). The XRD and SEM data concluded the presence of alloy formation between Pd and Ni. The synthesized particles were used as an adsorbent for removal of azo dye acid orange-8 (AO-8) from water and were found to be effective in removal (over 90% removal efficiency) of the selected dye. Different kinetics and equilibrium models were applied to calculate the adsorption parameters. The most suitable model that best fitted the equilibrium data was the Langmuir model and maximum adsorption capacities were 666.6, 714 and 769 mg/g at 293, 313 and 333 K, respectively, with R2 values closed to 1 while in the case of the kinetics data the best fit was obtained with a pseudo-second order kinetics model with a high R2 value. Furthermore, the adsorption thermodynamics parameters such as free energy, enthalpy, and entropy were calculated and the adsorption process was to found be exothermic with a value of ΔH° (−7.593 kJ mol−1), spontaneous as ΔG° values were negative (−18.7327, −19.4870, and −20.584 kJ/mol at 293, 313 and 333 K, respectively). A positive entropy change ΔS° with a value of 0.0384 kJ /mol K indicates increased disorder at the solid–solution interface during the adsorption process. An attempt was made to recycle the Pd-Ni/AC-CeO2 with suitable solvents and the recycled adsorbent was reused for 6 cycles with AO-8 removal efficiency up to 80%. Based on findings of the study, the synthesized adsorbent could effectively be used for the removal of other pollutants from wastewater, however, further studies are needed to prove the mechanisms. [ABSTRACT FROM AUTHOR]