Search

Infrared thermography is a valuable non-destructive tool for inspection of materials. It measures the surface temperature evolution, from which hidden defects may be detected. Yet, thermal cameras typically have a low native spatial resolution resulting in a blurry and low-quality thermal image sequence and videos. In this study, a novel adversarial deep learning framework, called Dual-IRT-GAN, is proposed for performing super-resolution tasks. The proposed Dual-IRT-GAN attempts to achieve the objective of improving local texture details, as well as highlighting defective regions. The generated high-resolution images are then delivered to the discriminator for adversarial training using GAN's framework. The proposed Dual-IRT-GAN model, which is trained on an exclusive virtual dataset, is demonstrated on experimental thermographic data obtained from fibre reinforced polymers having a variety of defect types, sizes, and depths. The obtained results show its high performance in maintaining background colour consistency and removing undesired noise, and in highlighting defect zones with finer detailed textures in highresolution.

Nowadays, many researchers develop rate-dependent composite material models for application in dynamic simulations. Ideally, full stress-strain curves at a wide range of strain rates are available for identification of the different parameters of these models. Dynamic tensile tests are needed to produce the experimental input data. However, especially for brittle materials, data acquisition during these tests becomes critical. The effect of synchronization on the test results was investigated by conducting a series of dynamic tensile tests on three different brittle continuous-fibre composite laminates. It is demonstrated that synchronization errors of the order of 1 microsecond already have a significant effect on the test outcome at high rates. With the aid of a finite-element model, the limiting factors on the maximum attainable strain rate are quantified. [ABSTRACT FROM AUTHOR]

ABSTRACT Local stiffness of Euler-Bernoulli beams can be identified by dividing the bending moment of a deformed beam by the local curvature. Curvature and moment distributions can be derived from the modal shape of a beam vibrating at resonance. In this article, the modal shape of test beams is measured by both scanning laser vibrometry (SLV) and shearography. Shearography is an interferometric optical method that produces full-field displacement gradients of the inspected surface. Curvature can be obtained by two steps of derivation of the modal amplitude (in the case of SLV) or one step of derivation of the modal shape slope (in the case of shearography). Three specially prepared aluminium beams with a known stiffness distribution are used for the validation of both techniques. The uncertainty of the identified stiffness distributions with both techniques is compared and related to their signal-to-noise ratios. A strength and weakness overview at the end of the article reveals that the shearography is the technique that shows the most advantages. [ABSTRACT FROM AUTHOR]

Coronary function testing (CFT) plays a pivotal role in the diagnosis of coronary vascular dysfunction and providing patients with tailored therapy. The Belgian registry on CFT (BELmicro registry) is a prospective, observational, multicenter registry including 14 centers in Belgium. All patients who underwent clinically indicated CFT were included in the registry. Baseline characteristics, CFT data, and clinical outcomes were collected. This analysis aimed to describe the baseline characteristics of a real-world population of patients who underwent CFT, evaluate the prevalence of coronary vascular dysfunction, and assess the safety of CFT in daily clinical practice. Between October 2021 and September 2023, 449 patients were enrolled. The mean age was 65 ± 10 years, and 47.4% of patients were men. A total of 59% of patients had hypertension, 18.7% had diabetes, 69.5% had hypercholesterolemia, and 40.1% had a smoking habit. Angina and nonobstructive coronary arteries (ANOCAs) were identified in 85.1% of the patients. Microvascular physiology assessment was performed in 95.5% of patients, vasoreactivity test in 28.5%, and both in 24.0%. coronary microvascular dysfunction was diagnosed in 23.4% of patients with ANOCA, epicardial vasospasm in 26.3%, and microvascular spasm in 14.9%. Rates of major complications were 0.7% for microvascular physiology assessment and 0% for vasoreactivity test. In conclusion, participants in the BELmicro registry represented a real-world population of patients, characterized by a high burden of cardiovascular risk factors. Coronary microvascular dysfunction and coronary vasospasm were frequent in patients with ANOCA. Performing CFT in daily clinical practice was feasible, with a low rate of complications., Competing Interests: Declaration of competing interest Dr. Segers reports financial support from Abbott Vascular and Fund for Scientific Research Flanders. The remaining authors have no competing interests to declare., (Copyright © 2024 Elsevier Inc. All rights reserved.)

This study investigates the effectiveness of polyether block amide (PEBA) thermoplastic elastomeric nanofibers in reducing low-velocity impact damage across three carbon fiber composite lay-up configurations: a cross-ply [0°/90°]2s (CP) and a quasi-isotropic [0°/45°/90°/-45°]s (QI) lay-up utilizing unidirectional plies, and a stacked woven [(0°,90°)]4s (W) lay-up using twill woven fabric plies. The flexural strength and interlaminar shear strength of the composites remained unaffected by the addition of nanofibers: around 750 MPa and 63 MPa for CP, 550 MPa and 58 MPa for QI, and 650 MPa and 50 MPa for W, respectively. The incorporation of nanofibers in the interlaminar regions resulted in a substantial reduction in projected damage area, ranging from 30% to 50% reduction over an impact energy range of 5-20 J. Microscopic analysis showed that especially the delamination damage decreased in toughened composites, while intralaminar damage remained similar for the cross-ply and quasi-isotropic lay-ups and decreased only in the woven lay-up. This agrees with the broad body of research that shows that interleaved nanofibers result in a higher delamination resistance due to toughening mechanisms related to nanofiber bridging of cracks. Despite their ability to mitigate delamination during impact, nanofibers showed limited positive effects on Compression After Impact (CAI) strength in quasi-isotropic and cross-ply composites. Interestingly, only the woven fabric composites demonstrated improved CAI strength, with a 12% improvement on average over the impact energy range, attributed to a reduction in both interlaminar and intralaminar damage. This study indicates the critical role of fiber integrity over delamination size in determining CAI performance, suggesting that the delaminations are not sufficiently large to induce buckling of sub-layers, thereby minimizing the effect of nanofiber toughening on the CAI strength.

Scanning laser Doppler vibrometry is a widely adopted method to measure the full-field out-of-plane vibrational response of materials in view of detecting defects or estimating stiffness parameters. Recent technological developments have led to performant 3D scanning laser Doppler vibrometers, which give access to both out-of-plane and in-plane vibrational velocity components. In the present study, the effect of using (i) the in-plane component; (ii) the out-of-plane component; and (iii) both the in-plane and out-of-plane components of the recorded vibration velocity on the inverse determination of the stiffness parameters is studied. Input data were gathered from a series of numerical simulations using a finite element model (COMSOL), as well as from broadband experimental measurements by means of a 3D infrared scanning laser Doppler vibrometer. Various materials were studied, including carbon epoxy composite and wood materials. The full-field vibrational velocity response is converted to the frequency-wavenumber domain by means of Fourier transform, from which complex wavenumbers are extracted using the matrix pencil decomposition method. To infer the orthotropic elastic stiffness tensor, an inversion procedure is developed by coupling the semi-analytical finite element (SAFE) as a forward method to the particle swarm optimizer. It is shown that accounting for the in-plane velocity component leads to a more accurate and robust determination of the orthotropic elastic stiffness parameters.

A new extension of the shear deformation theory to fifth order in order to calculate the spectrum of Lamb waves in orthotropic media over a wide frequency range is developed and analyzed. The aspiration of the proposed method is to create an alternative framework to exhaustive 3D elasticity based solutions by increasing computational efficiency without losing accuracy, nor robustness. A new computational framework is introduced which allows to estimate the dispersion curves for the first nine symmetric and nine anti-symmetric Lamb modes. Analytically calculated dispersion curves using 5-SDT for different propagation directions and polar plots for selected frequency of different materials are compared with the results from both the semi analytical finite element method, and lower order shear deformation theories. Careful analysis for individual laminae and for symmetric composite laminates exhibits a good agreement between the new higher order plate theory and the semi analytical finite element method over an extensive frequency range. In addition, attenuation plots show that the proposed method can also be used for visco-elastic materials (or highly damped materials). The advantage of the new higher order plate theory and its numerical implementation is that it is much more computationally efficient compared to comprehensive methods as Lamb wave polar plots of composite plates as function of incidence angle, polar angle and frequency can be calculated in less than a second on a standard laptop. Consequently, the use of this framework in inversion routines opens up the possibility of quasi real-time Structural Health Monitoring for visco-elastic composites covering a sufficiently wide frequency range., (Copyright © 2021 Elsevier B.V. All rights reserved.)

In the context of designing a next-generation ultrasonic polar scan (UPS) measurement system for viscoelastic material characterization, a novel approach is proposed, which draws on a set of cylindrically focused emitters in conjunction with a circular phased array (C-PA) receiver in order to create a portable measurement system while improving the data quality and ease the data interpretation. To explore the potential of the new approach and determine its optimal design parameters, a 3-D analytical model is presented to numerically simulate UPS experiments with the proposed system. Furthermore, a postprocessing procedure is worked out to treat the acquired raw data with the aim to deal with the integrating effect of finite size transducers and directly reconstruct the angle-dependent plane wave reflection coefficients of the sample under study. As the accuracy of the reconstruction heavily depends on various design parameters, a parameter study focusing on the influence of three main experimental parameters is performed to guide the optimal design. For each of these parameter studies, the UPS simulation results have been inverted, and the errors on the estimated C-tensor parameters have been deduced. First, it is shown that, for a given frequency, the radius of the C-PA must be large enough to capture both the specular and nonspecular reflected field, which is crucial to assure a correct reconstruction of the plane wave characteristics and find proper estimates of the C-tensor parameters. Second, the impact of the emitter and receiver lengths on the quality of the reconstruction and the C-tensor parameters has been investigated, yielding superior results upon increasing either of them. Finally, a dedicated study of the pitch of the C-PA elements and the angular range of the cylindrically focused emitters shows that aliasing effects disturb the results if the pitch is too large. However, this effect can somewhat be mitigated by employing multiple emitters with a restricted angular range. Using the knowledge of the abovementioned parameter studies, a simulated UPS experiment using a proper set of design parameters is performed for a cross-ply carbon epoxy laminate. The postprocessed reconstruction based on these data shows an excellent agreement with the theoretical plane wave results.

UD glass/PA6 coupons with an open hole are subjected to tensile and compressive loading. Three layups: [0/90] 5s , [+45/-45] 5s and [+45/0/-45/90] 3s with a shape based on ASTM D5766 were tested. Both monotonic loading as well as loading-unloading-reloading tests were executed. The strain field on the sample surface was measured with digital image correlation. This allowed identifying the distribution of the strain field during loading, permanent deformation and the evolution of the sample elastic modulus. This information is not frequently measured. Yet, it is vital for the development and validation of advanced failure models. The results indicate that the thermoplastic matrix allows large plastic deformation under tensile loading for the specimens with layup [+45/-45] 5s . In addition, the specimen elastic modulus reduces by about 70%. The other layups show minor permanent deformation, while the elastic modulus reduces by up to 15%. Furthermore, the quasi-isotropic laminate shows a significant post-failure load-bearing capacity under compression loading. The results are complemented with post-mortem damage and fracture observations using optical microscopy and ultrasound inspection.

This paper proposes an efficient non-destructive testing technique for composite materials. The proposed vibro-thermal wave radar (VTWR) technique couples the thermal wave radar imaging approach to low-power vibrothermography. The VTWR is implemented by means of a binary phase modulation of the vibrational excitation, using a 5 bit Barker coded waveform, followed by matched filtering of the thermal response. A 1D analytical formulation framework demonstrates the high depth resolvability and increased sensitivity of the VTWR. The obtained results reveal that the proposed VTWR technique outperforms the widely used classical lock-in vibrothermography. Furthermore, the VTWR technique is experimentally demonstrated on a 5.5 mm thick carbon fiber reinforced polymer coupon with barely visible impact damage. A local defect resonance frequency of a backside delamination is selected as the vibrational carrier frequency. This allows for implementing VTWR in the low-power regime (input power < 1 W). It is experimentally shown that the Barker coded amplitude modulation and the resultant pulse compression efficiency lead to an increased probing depth, and can fully resolve the deep backside delamination.

Recently, researchers proposed the use of ultrasound combined with analytic-signal concepts for the reconstruction of the internal ply structure of composites. Optimal parameters for the pulse-echo mode ultrasonic testing are determined by modeling the analytic-signal response. The internal structure can be reconstructed by instantaneous metrics based on the interaction of the multilayer structure and the ultrasonic wave. However, there are certain drawbacks associated with the use of instantaneous metrics. The phase-derived interply track tends to be sensitive to the inspection conditions. This paper analytically studies the errors of the interply tracking for a wide range of parameters, including (i) signal-to-noise ratio, (ii) bandwidth, (iii) interply thickness, and (iv) attenuation, amongst others. It provides a guideline on how to improve the performance of the interply tracking procedure in real measurements. An experimental study combining the analytic-signal procedure with a standard log-Gabor filter in the frequency domain is performed to derive the interply tracks of a 24-layer composite laminate in a robust way. The bandpass filter selects the appropriate frequency band of the analytic-signal response from the composite. It shows a good ability for frequency and bandwidth selection, and can efficiently cope with noise features. The reconstructed ply tracks in A-scan, B-scan, and C-scan modes are analyzed to verify the performance of this procedure., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Local Defect Resonance (LDR) is exploited for non-destructive testing (NDT) by using ultrasonic vibrations to get a localized resonant activation of defected zones. The LDR technique relies on the local stiffness difference between the defect and the sound material. Analyzing the structure's displacement field at this localized resonance frequency reveals the defect's location and provides information about the defect's characteristics, i.e. geometry, size and depth. In this study, the opportunities and limitations of linear LDR for NDT of materials are investigated in a parametric way. Both finite element simulations and experiments (using scanning laser Doppler vibrometry) are performed for aluminum alloy and carbon fiber reinforced polymer coupons with flat bottom holes and delaminations ranging in both depth and diameter. The resonance frequencies as well as the associated defect-to-background ratios are parametrically evaluated. For shallow defects, a clear LDR is observed caused by the strong local stiffness reduction at the defect. On the contrary, deep defects are associated with a limited stiffness decrease that results in the absence of LDR behavior. The local stiffness reduction at damages is further exploited using a weighted band power calculation. It is shown that using this technique, deep defects can be detected for which no LDR behavior was observed., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

For centuries, wood, and more specifically spruce, has been the material of choice for violin top plates. Lately, carbon fiber instruments have entered the market. Some studies show that composite materials have potential advantages for making instruments [Damodaran, Lessard, and Babu, Acoust. Aust. 43, 117-122 (2015)]. However, no studies exist that evaluate violins made of different composite materials as judged by listeners. For this study, six prototype violins, differing only by the material of the top plate, were manufactured in a controlled laboratory setting. The six prototype violins were judged by experienced listeners in two double-blind experiments. In contrast to popular opinion that violins made from carbon have or lack a specific sound quality, the study provides insights in the diverse sounds and timbres violins from fiber-reinforced polymers can create. It allows an investigation of the links between the perception and the variations in material properties of the soundboards. Additionally, as neither players nor listeners are acquainted with these instruments, these results provide an interesting view on what type of qualities of violin-like sounds are preferred by listeners.

Numerical finite-element (FE) simulations and postprocessing analysis methods are presented for ultrasonic polar scan (UPS) measurements involving a circular phased array (C-PA) to determine the plane-wave reflection coefficient of plates. Apodization weights for the C-PA elements are determined to assure the generation of a quasi-plane wave upon excitation at the plate surface and to mitigate bounded beam effects on the assessed reflection coefficient. In addition, postprocessing of the reflection signals is performed via the synthetic plane-wave technique to further filter out any bounded beam effects. Reflection coefficients are presented for three cases namely, an aluminum, a unidirectional carbon epoxy, and a cross-ply carbon epoxy plate. For all three cases, comparison with the analytical plane-wave theory shows excellent agreement with the reflection coefficients obtained by the C-PA and the additional postprocessing steps for both the pulsed and harmonic signals. It is also shown that the agreement becomes considerably worse if the nonspecular reflection field is disregarded in the postprocessing treatment, thus enforcing the need to capture the full reflected field via the PA whenever plane-wave reflection coefficients are needed.

Porous phononic crystal plates (PhPs) that are produced by perpendicular perforation of a uniform plate have well-known characteristics in selective manipulation (filtration, resonation, and steering) of guided wave modes. This paper introduces novel designs of porous PhPs made by an oblique perforation angle. Such obliquely perforated PhPs (OPhPs) have a non-uniform through-the-thickness cross section, which strongly affects their interaction with various wave mode types and therefore their corresponding phononic properties. Modal band analysis is performed in unit-cell scale and variation of phononic bandgaps with respect to the perforation angle is studied within the first 10 modal branches. Unit-cells with arbitrary perforation profile as well as unit-cells with optimized topology for maximized bandgap of fundamental modes are investigated. It is observed that the oblique perforation has promising effects in enhancing the unidirectional and/or omnidirectional bandgap efficiency, depending on the topology and perforation angle of OPhP.

This paper describes an integrated six-beam homodyne laser Doppler vibrometry (LDV) system based on a silicon-on-insulator (SOI) full platform technology, with on-chip photo-diodes and phase modulators. Electronics and optics are also implemented around the integrated photonic circuit (PIC) to enable a simultaneous six-beam measurement. Measurement of a propagating guided elastic wave in an aluminum plate (speed ≈ 909 m/s @ 61.5 kHz) is demonstrated.

Shear wave elastography (SWE) is a potentially valuable tool to noninvasively assess ventricular function in children with cardiac disorders, which could help in the early detection of abnormalities in muscle characteristics. Initial experiments demonstrated the potential of this technique in measuring ventricular stiffness; however, its performance remains to be validated as complicated shear wave (SW) propagation characteristics are expected to arise due to the complex non-homogenous structure of the myocardium. In this work, we investigated the (i) accuracy of different shear modulus estimation techniques (time-of-flight (TOF) method and phase velocity analysis) across myocardial thickness and (ii) effect of the ventricular geometry, surroundings, acoustic loading, and material viscoelasticity on SW physics. A generic pediatric (10-15-year old) left ventricular model was studied numerically and experimentally. For the SWE experiments, a polyvinylalcohol replicate of the cardiac geometry was fabricated and SW acquisitions were performed on different ventricular areas using varying probe orientations. Additionally, the phantom's stiffness was obtained via mechanical tests. The results of the SWE experiments revealed the following trends for stiffness estimation across the phantom's thickness: a slight stiffness overestimation for phase speed analysis and a clear stiffness underestimation for the TOF method for all acquisitions. The computational model provided valuable 3-D insights in the physical factors influencing SW patterns, especially the surroundings (water), interface force, and viscoelasticity. In conclusion, this paper presents a validation study of two commonly used shear modulus estimators for different ventricular locations and the essential role of SW modeling in understanding SW physics in the pediatric myocardium.