Search

Reverse osmosis (RO) filtration performance is heavily influenced by the design of the feed spacer. Spacer design impacts hydrodynamic patterns within the system, affecting water production and concentration polarization. Two spacer designs, namely pillar (P) and standard (S), were investigated to improve the performance of a commercially available spacer design (C) in the RO process. Two approaches were employed to evaluate spacer performance. First, direct numerical simulation (DNS) was utilized to fundamentally understand the hydrodynamics generated by each spacer design. Second, laboratory RO experiments were conducted to confirm the simulation results. The P and S spacers induced higher flow velocity and vorticity than the C spacer, as confirmed by simulations and experiments. Reduced dead zones were also demonstrated using P and S spacers. However, the standard spacer design exhibited a clear advantage in promoting more efficient mixing within the filtration channels. This enhanced mixing substantially reduced salt concentration at the membrane surface, improving the filtration performance. In agreement with the permeation velocity computation, the S spacer achieved the highest improvement (13%) in both flux yield and specific flux relative to the C spacer. This finding confirms the S spacer's ability to enhance RO performance while reducing energy consumption.

Membrane distillation (MD) scale-up is challenged by ineffective heat recovery and the temperature polarization effect. Direct contact membrane distillation (DCMD) modules suffer high thermal conduction losses due to feed flow direction along the length of the membrane, resulting in low thermal efficiency. We propose a novel module design named coiled hollow fiber (CHF) to decouple the flow direction from the membrane surface in hollow fiber (HF) DCMD. Experimental and computational analyses were employed to compare the performance of CHF and the conventional design. The CHF module design successfully mitigates the TP effect in HF DCMD, increasing the flux by 148 % and 163 % in cross-flow and localized heating (LH) modes, respectively. Moreover, CHF operated in LH mode exhibits the lowest energy consumption of all configurations (81 % decrease) compared to the conventional design. This novel module design represents a new pathway for efficient and highly performing DCMD module., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Optimal spacer design enhances the filtration performance in spiral-wound modules by controlling the local hydrodynamics inside the filtration channel. A novel airfoil feed spacer design fabricated using 3D-printing technology is proposed in this study. The design is a ladder-shaped configuration with primary airfoil-shaped filaments facing the incoming feed flow. The airfoil filaments are reinforced by cylindrical pillars supporting the membrane surface. Laterally, all the airfoil filaments are connected by thin cylindrical filaments. The performances of the novel airfoil spacers are evaluated at Angle of Attack (AOA) of 10 ° (A-10 spacer) and 30 ° (A-30 spacer) and compared with commercial (COM) spacer. At fixed operating conditions, simulations indicate steady-state hydrodynamics inside the channel for A-10 spacer, while an unsteady state is found for A-30 spacer. Numerical wall shear stress for airfoil spacers is uniformly distributed and has a higher magnitude than the COM spacer. A-30 spacer design is the most efficient in ultrafiltration process with enhanced permeate flux (228%) and reduced specific energy consumption (23%) and biofouling development (74%) as characterized by Optical Coherence Tomography. Results systematically demonstrate the influential role of airfoil-shaped filaments for feed spacer design. Modifying AOA allows localized hydrodynamics to be effectively controlled according to the filtration type and operating conditions., (© 2023. The Author(s).)

Artificial lung technology is advancing at a startling rate raising hopes that it would better serve the needs of those requiring respiratory support. Whether to assist the healing of an injured lung, support patients to lung transplantation, or to entirely replace native lung function, safe and effective artificial lungs are sought. After 200 years of bioengineering progress, artificial lungs are closer than ever before to meet this demand which has risen exponentially due to the COVID-19 crisis. In this review, the critical advances in the historical development of artificial lungs are detailed. The current state of affairs regarding extracorporeal membrane oxygenation, intravascular lung assists, pump-less extracorporeal lung assists, total artificial lungs, and microfluidic oxygenators are outlined.

Feed spacers are the critical components of any spiral-wound filtration module, dictating the filtration performance. Three spacer designs, namely a non-woven commercial spacer (varying filament cross-section), a symmetric pillar spacer, and a novel hole-pillar spacer (constant filament diameter) were studied using Direct Numerical Simulations (DNS), 3-D printed and subsequently experimentally tested in a lab-scale ultrafiltration set-up with high biofouling potential feed water at various feed pressures. Independent of the applied pressure, the novel hole-pillar spacer showed initially the lowest feed channel pressure drop, the lowest shear stress, and the highest permeate flux compared to the commercial and pillar spacers. Furthermore, less biofilm thickness development on membrane surface was visualized by Optical Coherent Tomography (OCT) imaging for the proposed hole-pillar spacer. At higher feed pressure, a thicker biofilm developed on membrane surface for all spacer designs explaining the stronger decrease in permeate flux at high pressure. The findings systematically demonstrated the role of various spacer designs and applied pressure on the performance of pre-treatment process, while identifying specific shear stress distribution guidelines for engineering a new spacer design in different filtration techniques.

An appropriate spacer design helps in minimizing membrane fouling which remains the major obstacle in forward osmosis (FO) systems. In the present study, the performance of a hole-type spacer (having holes at the filament intersections) was evaluated in a FO system and compared to a standard spacer design (without holes). The hole-type spacer exhibited slightly higher water flux and reverse solute flux (RSF) when Milli-Q water was used as feed solution and varied sodium chloride concentrations as draw solution. During shale gas produced water treatment, a severe flux decline was observed for both spacer designs due to the formation of barium sulfate scaling. SEM imaging revealed that the high shear force induced by the creation of holes led to the formation of scales on the entire membrane surface, causing a slightly higher flux decline than the standard spacer. Simultaneously, the presence of holes aided to mitigate the accumulation of foulants on spacer surface, resulting in no increase in pressure drop. Furthermore, a full cleaning efficiency was achieved by hole-type spacer attributed to the micro-jets effect induced by the holes, which aided to destroy the foulants and then sweep them away from the membrane surface.

Biofilm attachment and growth in membrane filtration systems are considerably influenced by the localized flow inside the feed channel. The present work aims to map the biofilm attachment/growth mechanism under varying flow conditions. Effect of varying clearance region (space between the spacer filament and membrane surface) on biofouling pattern is investigated by using three 3D-printed pillar spacers having different filament diameters of 340, 500, and 1000 µm while maintaining the same pillar orientation, diameter and height. Direct Numerical Simulations (DNS) and Optical Coherence Tomography (OCT) were carried out to accurately predict the local hydrodynamics behavior and in-situ monitor the biofilm formation. On spacer filaments, biofouling attachment is primarily observed in the regions where low and non-fluctuating shear stresses are present. Conversely, on membrane surface, highest biofouling attachment was observed under spacer filaments where high shear stresses are prevalent along with low clearance height. Furthermore, as filtration time progresses, the biofilm grows faster on the membrane in the center of spacer cells where low shear stress with steady hydrodynamics conditions are prevalent. The proposed hydrodynamics approach envisages a full spectrum of spacer design constraints that can lead to intrinsic biofilm mitigation while improving filtration performance of membranes based water treatment., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020. Published by Elsevier Ltd.)

Modification of the feed spacer design significantly influences the energy consumption of membrane filtration processes. This study developed a novel column type feed spacer with the aim to reduce the specific energy consumption (SEC) of the membrane based water filtration system. The proposed spacer increases the clearance between the filament and the membrane (reducing the spacer filament diameter) while keeping the same flow channel thickness as compared to a standard non-woven symmetric spacer. Since the higher clearance reduces the flow unsteadiness, column type nodes were added in the spacer structure as additional vortex shading bodies. Fluid flow behaviour in the channel for this spacer was numerically simulated by 3D CFD studies and then compared with the standard spacer. The numerical results showed that the proposed spacer substantially reduced the pressure drop, shear stress at the constriction region and shortened the dead zone. Finally, these findings were confirmed experimentally by investigating the filtration performances using the 3D printed prototypes of these spacers in a lab-scale filtration module. It is observed that the column spacer reduced the pressure drop by three times and doubled the specific water flux. 2D OCT (Optical Coherence Tomography) scans of the membrane surface acquired after the filtration revealed much lower biomass accumulation using the proposed spacer. Consequently, the SEC for the column spacer was found about two folds lower than the standard spacer., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

The improvement of feed spacers with optimal geometry remains a key challenge for spiral-wound membrane systems in water treatment due to their impact on the hydrodynamic performance and fouling development. In this work, novel spacer designs are proposed by intrinsically modifying cylindrical filaments through perforations. Three symmetric perforated spacers (1-Hole, 2-Hole, and 3-Hole) were in-house 3D-printed and experimentally evaluated in terms of permeate flux, feed channel pressure drop and membrane fouling. Spacer performance is characterized and compared with standard no perforated (0-Hole) design under constant feed pressure and constant feed flow rate. Perforations in the spacer filaments resulted in significantly lowering the net pressure drop across the spacer filled channel. The 3-Hole spacer was found to have the lowest pressure drop (50%-61%) compared to 0-Hole spacer for various average flow velocities. Regarding permeate flux production, the 0-Hole spacer produced 5.7 L m -2 .h -1 and 6.6 L m -2 .h -1 steady state flux for constant pressure and constant feed flow rate, respectively. The 1-Hole spacer was found to be the most efficient among the perforated spacers with 75% and 23% increase in permeate production at constant pressure and constant feed flow, respectively. Furthermore, membrane surface of 1-Hole spacer was found to be cleanest in terms of fouling, contributing to maintain higher permeate flux production. Hydrodynamic understanding of these perforated spacers is also quantified by performing Direct Numerical Simulation (DNS). The performance enhancement of these perforated spacers is attributed to the formation of micro-jets in the spacer cell that aided in producing enough unsteadiness/turbulence to clean the membrane surface and mitigate fouling phenomena. In the case of 1-Hole spacer, the unsteadiness intensity at the outlet of micro-jets and the shear stress fluctuations created inside the cells are higher than those observed with other perforated spacers, resulting in the cleanest membrane surface., (Copyright © 2018 Elsevier Ltd. All rights reserved.)