Search

Suspoemulsions are used for food, cosmetic and pharmaceutical products, including food such as dairy products and non-dairy alternatives. Product properties, such as flow behavior or sensory perception of non-dairy products differ from those of dairy products and are therefore perceived by consumers as products of inferior quality. One reason for this may be the crystallization behavior of the added triglycerides leading to differences in solid fat content in comparison to cow milk. This is discussed with the solidity of the dispersed phase as a parameter of suspoemulsions. The solidity was varied by using low and high melting triglycerides and measuring at different temperatures. The dispersed phase fraction is φ = 30%. The droplet size distribution showed a x 50,3 of 1.2 and 3.66 μm, mimicking the droplet sizes of milk and dairy cream. Rheological frequency sweeps were carried out within a temperature range from 5°C to 50°C. The differences in solidity of the dispersed phase caused no changes in viscosity at each temperature. In contrast, oral tribology distinguished different solidities of the dispersed phase with changes in the friction coefficient. The friction coefficient was determined for increasing rotational speeds (0.01-100 mm/s), to compare the so called Stribeck curves with each other. In general, with increasing solidity of the dispersed phase, the friction coefficient increases. Comparing the Stribeck curves of pure butter fat suspoemulsion with those of plant-based fat suspoemulsions, different plant-based fats can be mixed, to mimic the friction profile of milk products in plant-based alternatives., (© 2024 The Author(s). Journal of Texture Studies published by Wiley Periodicals LLC.)

High-moisture extrusion of plant proteins to create meat-like structures is a process that has met with increasing attention in the recent past. In the process, the proteins are thermomechanically stressed in the screw section of the extruder, and the resulting protein gel is structured in the attached cooling die. Various protein sources, notably soy protein isolate (SPI) and wheat gluten, are used to form gels with different networks: SPI creates a physical, non-covalent network, while gluten forms a chemical, covalent one. The food industry frequently adds weak acids to modify taste and shelf life. However, it is known that a change in pH affects the gelation behavior of proteins because the repulsive forces within and between the proteins change. The research reported here was carried out to investigate for the two proteins mentioned the influence of pH modification by the addition of citric acid and acetic acid on gel formation and the meat-like structures produced. For this purpose, materials and parameters were screened using a closed cavity rheometer, followed by extrusion trials at pH 7.36-4.14 for SPI and pH 5.83-3.37 for gluten. The resulting extrudates were analyzed optically and mechanically, and protein solubility was tested in a reducing buffer. For both protein systems, the addition of acid results in less pronounced meat-like structures. At decreasing pH, the complex viscosity of SPI increases (from 11,970 Pa·s to 40,480 Pa·s at 100 °C), the generated gel becomes stronger (strain decreased from 0.62 to 0.48 at 4.5 × 10 5 Pa), and the cross-linking density grows. For gluten, a decreasing pH results in altered reaction kinetics, a more deformable resulting gel (strain increased from 0.7 to 0.95 at 4.5 × 10 5 Pa), and a decreased cross-linking density. Solubility tests show that no additional covalent bonds are formed with SPI. With gluten, however, the polymerization reaction is inhibited, and fewer disulfide bonds are formed.

A closed cavity rheometer was used to study the rheology of dry-fractionated mung bean protein -DFMB- (55% protein d.m.). Then, the high-moisture extrusion cooking at 40% and 50% moisture contents and different temperatures (115, 125, 135 and 145 °C) was performed, investigating the impact on structural, textural, and rheological properties of extrudates. When subjected to a temperature ramp (40-170 °C), DFMB showed an increase of G* from 70 °C, as a consequence of starch gelatinization and protein gelation. The peak, indicating the end of aggregation reactions, was at 105 °C and 110 °C for DFMB at 50% and 40% moisture content, respectively. The time sweep analysis described the protein behavior in no-shear/shear conditions, highlighting a more pronounced effect of the temperatures compared to moisture content. During the extrusion cooking, the temperature increase led to a decrease of pressure, indicating a reduction of the melt viscosity. The microstructure of the extrudates showed a more pronounced anisotropic profile when higher temperatures were applied. Hardness, chewiness, and cohesion were directly correlated with the temperature, which also affected the rheological properties of extrudates. A combination of textural and rheological analyses can offer a clear overview of the structural characteristics of meat analogues., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2023 The Author(s).)

Understanding of generation, extent and location of thermomechanical stress in small-scale (< 3 g) ram and twin-screw melt-extrusion is crucial for mechanistic correlations to the stability of protein particles (lysozyme and BSA) in PEG-matrices. The aim of the study was to apply and correlate experimental and numerical approaches (1D and 3D) for the evaluation of extrusion process design on protein stability. The simulation of thermomechanical stress during extrusion raised the expectation of protein degradation and protein particle grinding during extrusion, especially when TSE was used. This was confirmed by experimental data on protein stability. Ram extrusion had the lowest impact on protein unfolding temperatures, whereas TSE showed significantly reduced unfolding temperatures, especially in combination with kneading elements containing screws. In TSE, the mechanical stress in the screws always exceeded the shear stress in the die, while mechanical stress within ram extrusion was generated in the die, only. As both extruder designs revealed homogeneously distributed protein particles over the cross section of the extrudates for all protein-loads (20-60%), the dispersive power of TSE revealed not to be decisive. Consequently, the ram extruder would be favored for the production of stable protein-loaded extrudates in small scale., Competing Interests: None., (© 2023 The Authors.)

Sugar beet pectins (SBPs) are known for their emulsifying properties, but it is yet unknown which structural elements are most important for functionality. Recent results indicated that the arabinose content has a decisive influence, but the approach applied did not allow causality to be established. In this study, a mostly intact SBP was selectively modified and the obtained pectins were analyzed for their molecular structure and their emulsifying properties. De-esterification only resulted in a moderate increase in droplet size. The length of the pectin backbone only influenced the emulsifying properties when the homogalacturonan backbone was cleaved to a higher extent. By using different arabinan-modifying enzymes, it was demonstrated that both higher portions and chain lengths of arabinans positively influence the emulsifying properties of SBPs. Therefore, we were able to refine the structure-function relationships for acid-extracted SBPs, which can be used to optimize extraction conditions.

Hypothesis: Double emulsions with many monodispersed internal droplets are required for the fabrication of multicompartment microcapsules and tissue-like synthetic materials. These double emulsions can also help to optically resolve different coalescence mechanisms contributing to double emulsion destabilization. Up to date microfluidic double emulsions are limited to either core-shell droplets or droplets with eight or less inner droplets. By applying a two-step jet break-up within one setup, double emulsion droplets filled with up to several hundred monodispersed inner droplets can be achieved., Experiments: Modular interconnected CNC-milled Lego®-inspired blocks were used to create two separated droplet break-up points within coaxial glass capillaries. Inner droplets were formed by countercurrent flow focusing within a small inner capillary, while outer droplets were formed by co-flow in an outer capillary. The size of inner and outer droplets was independently controlled since the two droplet break-up processes were decoupled., Findings: With the developed setup W/O/W and O/W/O double emulsions were produced with different surfactants, oils, and viscosity modifiers to encapsulate 25-400 inner droplets in each outer drop with a volume percentage of inner phase between 7% and 50%. From these emulsions monodispersed multicompartment microcapsules were obtained. The report offers insights on the relationship between the coalescence of internal droplets and their release., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2021 Elsevier Inc. All rights reserved.)

The influence of the conformation of sugar beet pectin (SBP) on the interfacial and emulsifying properties was investigated. The colloidal properties of SBP, such as zeta potential and hydrodynamic diameter, were characterized at different pH levels. Furthermore, pendant drop tensiometry and quartz crystal microgravimetry were used to study adsorption behavior (adsorbed mass and adsorption rate) and stabilizing mechanism (layer thickness and interfacial tension). A more compact conformation resulted in a faster reduction of interfacial tension, higher adsorbed mass, and a thicker adsorption layer. In addition, emulsions were prepared at varying conditions (pH 3-5) and formulations (1-30 wt% MCT oil, 0.1-2 wt% SBP), and their droplet size distributions were measured. The smallest oil droplets could be stabilized at pH 3. However, significantly more pectin was required at pH 3 compared to pH 4 or 5 to sufficiently stabilize the oil droplets. Both phenomena were attributed to the more compact conformation of SBP at pH < pK a : On the one hand, pectins adsorbed faster and in greater quantity, forming a thicker interfacial layer. On the other hand, they covered less interfacial area per SBP molecule. Therefore, the SBP concentration must be chosen appropriately depending on the conformation.

Pectin-based microgel particles (MGPs) are encouraging sustainable emulsifying agents for food-applications. Based on polyelectrolytes, pectin-based MGPs are assumed to be pH and ionic strength sensitive, in a similar manner to MGPs of synthetic polymers. Besides building a barrier around oil droplets, charged MGPs repulse each other. Thus the stabilisation mechanisms of pectin-based MGPs should be both steric and electrostatic. To investigate this, emulsions were homogenised with MGP concentrations ranging from 0.5 to 2 wt% MGPs. After emulsification, the pH of the emulsions was adjusted to 4, 3, or 2; and the resulting droplet sizes were measured. We found out that the droplet size and the appearance of agglomerates increased with decreasing pH values. This was caused by the loss of the MGP surface charge, as stated by their ζ-potential, showing an increase from -33.71 ± 4.1 mV for samples with pH 4 to -17 ± 0.6 mV, and -3.4 ± 0.6 mV for pH 3 and 2, respectively. However, the degree of coalescence was dependent on the MGP concentration, as samples with 0.5 wt% coalesced more readily than samples with 2 wt% MGP. These results help understand the emulsion stabilisation mechanisms of pectin-based MGPs and what effect formulation parameters have on the long-term stability of MGP-stabilised emulsions.

Plant-based meat analogues that mimic the characteristic structure and texture of meat are becoming increasingly popular. They can be produced by means of high moisture extrusion (HME), in which protein-rich raw materials are subjected to thermomechanical stresses in the extruder at high water content (>40%) and then forced through a cooling die. The cooling die, or generally the die section, is known to have a large influence on the products' anisotropic structures, which are determined by the morphology of the underlying multi-phase system. However, the morphology development in the process and its relationship with the flow characteristics are not yet well understood and, therefore, investigated in this work. The results show that the underlying multi-phase system is already present in the screw section of the extruder. The morphology development mainly takes place in the tapered transition zone and the non-cooled zone, while the cooled zone only has a minor influence. The cross-sectional contraction and the cooling generate elongational flows and tensile stresses in the die section, whereas the highest tensile stresses are generated in the transition zone and are assumed to be the main factor for structure formation. Cooling also has an influence on the velocity gradients and, therefore, the shear stresses; the highest shear stresses are generated towards the die exit. The results further show that morphology development in the die section is mainly governed by deformation and orientation, while the breakup of phases appears to play a minor role. The size of the dispersed phase, i.e., size of individual particles, is presumably determined in the screw section and then stays the same over the die length. Overall, this study reveals that morphology development and flow characteristics need to be understood and controlled for a successful product design in HME, which, in turn, could be achieved by a targeted design of the extruders die section.

Plant proteins in foods are becoming increasingly popular with consumers. However, their application in extruded products remains a major challenge, as the various protein-rich raw materials (e.g., from different plant origins) exhibit very different material properties. In particular, the rheological properties of these raw materials have a distinct influence on the extrusion process and must be known in order to be able to control the process and adjust the product properties. In this study, process-relevant rheological properties of 11 plant-based protein-rich raw materials (differing in plant origin, protein content, and manufacturer) are determined and compared. The results demonstrate distinct differences in the rheological properties, even when plant origin and protein content are identical. Time sweeps reveal not only large differences in development of viscosity over time, but also in magnitude of viscosity (up to 15-fold difference). All materials exhibit gel behaviour and strain thinning behaviour in the strain sweeps, whereas their behaviour in the non-linear viscoelastic range differs greatly. Typical relaxation behaviour of viscoelastic materials could be observed in the stress relaxation tests for all materials. Comparison of the maximum achieved shear stress, which correlates with the elastic properties, reveals an up to 53-fold difference. The results of this study could serve as a starting point for adapting raw material selection and composition to process and product design requirements and help to meet the challenge of applying plant-based proteins in food extrusion.

High moisture extrusion (HME) of meat analogues is often performed with raw materials containing multiple components, e.g., blends of different protein-rich raw materials. For instance, blends of soy protein isolate (SPI) and another component, such as wheat gluten, are used particularly frequently. The positive effect of blending on product texture is well known but not yet well understood. Therefore, this work targets investigating the influence of blending in HME at a mechanistic level. For this, SPI and a model protein, whey protein concentrate (WPC), were blended at three different ratios (100:0, 85:15, 70:30) and extruded at typical HME conditions (55% water content, 115/125/133 °C material temperature). Process conditions, rheological properties, morphology development, product structure and product texture were analysed. With increasing WPC percentage, the anisotropic structures became more pronounced and the anisotropy index ( AI ) higher. The achieved AI from the extrudates with a ratio of 70:30 (SPI:WPC) were considerably higher than comparable extrudates reported in other studies. In all extrudates, a multiphase system was visible whose morphology had changed due to the WPC addition. The WPC led to the formation of a much smaller dispersed phase compared to the overlying multiphase structure, the size of which depends on the thermomechanical stresses. These findings demonstrate that targeted mixing of protein-rich raw materials could be a promising method to tailor the texture of extruded meat analogues.

For the valorization of oilseed press cakes into food products, extrusion can be used. A common way of applying the protein- and fiber-rich press cakes in directly expanded products is the combination thereof with starch, since starch gives a favourable texture, which correlates directly to expansion. To control product properties like expansion of protein and fiber-rich extruded products, the underlying physicochemical changes of proteins, fibers and starch due to thermomechanical input need to be comprehensively described. In this study, rapeseed press cake (RPC) was extruded and treated under defined thermomechanical conditions in a closed-cavity rheometer, pure and in combination with four starches. The impact of starch type (potato PS, waxy potato WPS, maize MS, high-amylose maize HAMS) and temperature (20/25, 80, 100, 120, 140 °C) on protein solubility, starch gelatinization (D gel ), starch hydrolysis (S H ) and fiber solubility of the blends was evaluated. The extrusion process conditions were significantly affected by the starch type. In the extruded blends, the starch type had a significant impact on the protein solubility which decreased with increasing barrel temperature. Increasing barrel temperatures significantly increased the amount of soluble fiber fractions in the blends. At defined thermomechanical conditions, the starch type showed no significant impact on the protein solubility of the blends. Therefore, the observed effects of starch type on the protein solubility of extruded blends could be attributed to the indistinct process conditions due to differences in the rheological properties of the starches rather than to molecular interactions of the starches with the rapeseed proteins in the blends.

High-moisture extrusion is a common process to impart an anisotropic, meat-like structure to plant proteins, such as wheat gluten. The addition of oil during the process promises to enhance the sensory properties of the meat analogs. In this study, the influence of oil on extrusion-relevant parameters as well as the structure-related characteristics of extruded wheat gluten was investigated. Oil was added directly to the extruder at different contents (0, 2, 4, 6%) and addition points (front/end of the extruder barrel). Process conditions, complex viscosity, Young's modulus and oil phase morphology were determined as a function of oil content and oil addition point. With increasing oil content, material temperature, die pressure, and complex viscosity decreased. The addition of oil at the end of the extruder barrel reduced this effect compared to the addition of oil in the front part of the extruder. It was observed that the extrudate's tensile strength is a function of material temperature, resulting in an increase in tensile strength with increasing material temperature. The oil was dispersed in the gluten matrix as small droplets with irregular shape. As the oil content increased, the size of the oil droplets increased, while the addition of oil at the end of the extruder resulted in a decrease in droplet size.

Rapeseed press cake (RPC), an oil pressing side product rich in protein and fiber, can be combined with starch and valorized into directly expanded products using extrusion technology. The mechanism of starch expansion has been studied in detail, but the impact of RPC on expansion behavior is poorly understood. However, it can be linked to rheological and physicochemical properties and is a key product quality parameter. Blends with different amounts of RPC (0, 10, 40 g/100 g) were extruded at different barrel temperatures (100, 120, 140 °C) and moisture contents (24 or 29 g/100 g). The initial, intermediate and final sectional, longitudinal and volumetric expansion indices (SEI, LEI, VEI) were monitored directly, 10 s and 24 h after die exit to measure extrudate growth and shrinkage. The viscous and elastic properties of the extruded blends were investigated in a closed cavity rheometer. Starch and blends with 10 g/100 g RPC achieved a high initial SEI followed by significant short-term shrinkage. Blends containing 40 g/100 g RPC did not show any initial expansion. With increasing RPC content, the intermediate SEI decreased, but all samples reached a similar final SEI due to time-dependent swelling of the RPC blends. With increasing RPC content, the elasticity of the starch-based extruded samples significantly increased. Our study shows that comprehensive control and understanding of expansion mechanisms can be achieved only by investigating all stages of extrudate growth and shrinkage. We also found that the closed cavity rheometer is a powerful tool to correlate the rheological properties and expansion mechanisms of biopolymers.

The partial substitution of starch with dietary fiber (DF) in extruded ready-to-eat texturized (RTE) cereals has been suggested as a strategy to reduce the high glycemic index of these food products. Here, we study the impact of extrusion processing on pure chokeberry ( Aronia melanocarpa ) pomace powder (CPP) rich in DF and polyphenols (PP) focusing on the content and profile of the DF fractions, stability of PP, and techno-functional properties of the extrudates. Using a co-rotating twin-screw extruder, different screw speeds were applied to CPP with different water contents (c w ), which resulted in specific mechanical energies (SME) in the range of 145-222 Whkg -1 and material temperatures (T M ) in the range of 123-155 °C. High molecular weight soluble DF contents slightly increase with increasing thermomechanical stress up to 16.1 ± 0.8 g/100 g dm as compared to CPP (11.5 ± 1.2 g/100 g dm), but total DF (TDF) contents (58.6 ± 0.8 g/100 g dm) did not change. DF structural analysis revealed extrusion-based changes in the portions of pectic polysaccharides (type I rhamnogalacturonan) in the soluble and insoluble DF fractions. Contents of thermolabile anthocyanins decrease linearly with SME and temperature from 1.80 ± 0.09 g/100 g dm in CPP to 0.24 ± 0.06 g/100 g dm (222 Whkg -1 , 155 °C), but phenolic acids and flavonoids appear to be largely unaffected. Resulting techno-functional (water absorption and water solubility) and physical properties related to the sensory characteristics (expansion, hardness, and color) of pure CPP extrudates support the expectation that granulated CPP extrudates may be a suitable food ingredient rich in DF and PP.

Food by-products can be used as natural and sustainable food ingredients. However, a modification is needed to improve the technofunctional properties according to the specific needs of designated applications. A lab-scale twin-screw extruder was used to process enzymatically treated apple pomace from commercial fruit juice production. To vary the range of the thermomechanical treatment, various screw speeds (200, 600, 1000 min -1 ), and screw configurations were applied to the raw material. Detailed chemical and functional analyses were performed to develop a comprehensive understanding of the impact of the extrusion processing on apple pomace composition and technofunctional properties as well as structures of individual polymers. Extrusion at moderate thermomechanical conditions increased the water absorption, swelling, and viscosity of the material. An increase in thermomechanical stress resulted in a higher water solubility index, but negatively affected the water absorption index, viscosity, and swelling. Scanning electron microscopy showed an extrusion-processing-related disruption of the cell wall. Dietary fiber analysis revealed an increase of soluble dietary fiber from 12.6 to 17.2 g/100 g dry matter at maximum thermo-mechanical treatment. Dietary fiber polysaccharide analysis demonstrated compositional changes, mainly in the insoluble dietary fiber fraction. In short, pectin polysaccharides seem to be susceptible to thermo-mechanical stress, especially arabinans as neutral side chains of rhamnogalacturonan I.

In order to valorise food by-products into healthy and sustainable products, extrusion technology can be used. Thereby, a high expansion rate is often a targeted product property. Rapeseed press cake (RPC) is a protein- and fibre-rich side product of oil pressing. Although there is detailed knowledge about the expansion mechanism of starch, only a few studies describe the influence of press cake addition on the expansion and the physical quality of the extruded products. This study assessed the effect of RPC inclusion on the physical and technofunctional properties of starch-containing directly expanded products. The effect of starch type (native and waxy), RPC level (10, 40, 70 g/100 g), extrusion moisture content (24, 29 g/100 g) and barrel temperature (20-140 °C) on expansion, hardness, water absorption, and solubility of the extrudates and extruder response was evaluated. At temperatures above 120 °C, 70 g/100 g of RPC increased the sectional and volumetric expansion of extrudates, irrespective of starch type. Since expansion correlates with the rheological properties of the melt, RPC and RPC/starch blends were investigated pre- and postextrusion in a closed cavity rheometer at extrusion-like conditions. It was shown that with increasing RPC level the complex viscosity |ƞ*| of extruded starch/RPC blends increased, which could be linked to expansion behaviour.

The high moisture extrusion of plant proteins is well suited for the production of protein-rich products that imitate meat in their structure and texture. The desired anisotropic product structure of these meat analogues is achieved by extrusion at high moisture content (>40%) and elevated temperatures (>100 °C); a cooling die prevents expansion of the matrix and facilitates the formation of the anisotropic structure. Although there are many studies focusing on this process, the mechanisms behind the structure formation still remain largely unknown. Ongoing discussions are based on two very different hypotheses: structure formation due to alignment and stabilization of proteins at the molecular level vs. structure formation due to morphology development in multiphase systems. The aim of this paper is, therefore, to investigate the mechanism responsible for the formation of anisotropic structures during the high moisture extrusion of plant proteins. A model protein, soy protein isolate, is extruded at high moisture content and the changes in protein-protein interactions and microstructure are investigated. Anisotropic structures are achieved under the given conditions and are influenced by the material temperature (between 124 and 135 °C). Extrusion processing has a negligible effect on protein-protein interactions, suggesting that an alignment of protein molecules is not required for the structure formation. Instead, the extrudates show a distinct multiphase system. This system consists of a water-rich, dispersed phase surrounded by a water-poor, i.e., protein-rich, continuous phase. These findings could be helpful in the future process and product design of novel plant-based meat analogues.

By-products of fruits and vegetables like apple pomace can serve as techno-functional ingredients in foods. Due to their physicochemical properties, e.g., viscosity, water absorption, or oil-binding, food by-products can modify the texture and sensory perception of products like yogurts and baked goods. It is known that, by extrusion processing, the properties of by-products can be altered. For example, by thermo-mechanical treatment, the capacity of food by-products to increase viscosity is improved. However, the mechanism and involved components leading to the viscosity increase are unknown. Therefore, the complex viscosity of apple pomace dispersions and the involved fractions as pectin (a major part of the water-soluble fraction), water-soluble and water-insoluble fraction, were measured. In the investigated range, an increase in the pectin yield and water solubility was observed with increasing thermo-mechanical treatment by extrusion processing. However, pectin and water-soluble cell wall components had only a limited effect on the complex viscosity of apple pomace dispersions. The insoluble fraction (particles) were investigated regarding their swelling behavior and influence on the complex viscosity. An intensification of thermo-mechanical treatment resulted in increasing swelling behavior.

By-products of fruit and vegetable processing are an inexpensive and sustainable source of dietary fiber, potentially offering valuable functional properties such as water binding and thickening. Due to these favorable properties, they can be utilized to reformulate widely-consumed foods, e.g., bakery products or beverages. In this study, apple pomace was used as a model system to study whether extrusion technology affects food by-product functionality and thus has the potential to broaden the application of by-products in foods. The effect of the process parameters and the extent of thermo-mechanical treatment on the structural and functional properties of apple pomace were analyzed after extrusion trials using various screw speeds, water contents, and barrel temperatures. Compared to the raw material, apple pomace extruded at T barrel = 100 °C, n = 700 min -1 and m H2O = 17% showed an increased water solubility up to 33%. The water absorption increased from 5 to 19 Pa·s and the paste viscosity from 5 to 339 Pa·s by extrusion processing. Analyses of dietary fiber contents and fiber polysaccharide structures revealed that thermo-mechanical stress ( n = 700 min -1 , m H2O = 22%) increased the content of soluble dietary fiber from 12.5 to 16.7 g/100 g dry matter, and that the harshest conditions even enabled the formation of low-molecular-weight dietary fiber. Arabinans (as neutral rhamnogalacturonan I side chains) appeared to be most sensitive to thermo-mechanical stress, whereas xylans (i.e., a group of minor polysaccharides) were an example of a more stable fiber polysaccharide. Also, the degree of methylation of the pectic polysaccharides was strongly reduced from 50% to 15% when thermo-mechanical stress was applied. Imaging and pore size analysis showed that extrusion processing could disrupt the rigid cell wall macromolecular structure.

In this study, the influence of defined extrusion-like treatment conditions on the denaturation behavior and kinetics of single- and multi-component protein model systems at a protein concentration of 70% ( w/w ) was investigated. α-Lactalbumin (αLA) and β-Lactoglobulin (βLG), and whey protein isolate (WPI) were selected as single- and multi-component protein model systems, respectively. To apply defined extrusion-like conditions, treatment temperatures in the range of 60 and 100 °C, shear rates from 0.06 to 50 s⁻ 1 , and treatment times up to 90 s were chosen. While an aggregation onset temperature was determined at approximately 73 °C for WPI systems at a shear rate of 0.06 s⁻ 1 , two significantly different onset temperatures were determined when the shear rate was increased to 25 and 50 s⁻ 1 . These two different onset temperatures could be related to the main fractions present in whey protein (βLG and αLA), suggesting shear-induced phase separation. Application of additional mechanical treatment resulted in an increase in reaction rates for all the investigated systems. Denaturation was found to follow 2.262 and 1.865 order kinetics for αLA and WPI, respectively. The reaction order of WPI might have resulted from a combination of a lower reaction order in the unsheared system (i.e., fractional first order) and higher reaction order for sheared systems, probably due to phase separation, leading to isolated behavior of each fraction at the local level (i.e., fractional second order).

The influence of thermomechanical treatment (temperature 60 °C-100 °C and shear rate 0.06 s -1 -50 s -1 ) and mixing ratio of β-lactoglobulin (βLG) and α-lactalbumin (αLA) (5:2 and 1:1) on the denaturation and aggregation of whey protein model systems with a protein concentration of 60% and 70% ( w/w ) was investigated. An aggregation onset temperature was determined at approx. 80 °C for both systems (5:2 and 1:1 mixing ratio) with a protein concentration of 70% at a shear rate of 0.06 s -1 . Increasing the shear rate up to 50 s -1 led to a decrease in the aggregation onset temperature independent of the mixing ratio. By decreasing the protein concentration to 60% in unsheared systems, the aggregation onset temperature decreased compared to that at a protein concentration of 70%. Furthermore, two significantly different onset temperatures were determined when the shear rate was increased to 25 s -1 and 50 s -1 , which might result from a shear-induced phase separation. Application of combined thermal and mechanical treatment resulted in overall higher degrees of denaturation independent of the mixing ratio and protein concentration. At the conditions applied, the aggregation of the βLG and αLA mixtures was mainly due to the formation of non-covalent bonds. Although the proportion of disulfide bond aggregation increased with treatment temperature and shear rate, it was higher at a mixing ratio of 5:2 compared to that at 1:1.

Dietary fiber is a potential replacement for other ingredients such as starch in reformulated extruded breakfast cereals. Analysis of chokeberry pomace powder revealed a total dietary fiber content of 57.8 ± 2 g/100 g with 76% being insoluble, 20% high molecular soluble and 4% low molecular soluble dietary fiber. The fiber polysaccharide composition was analyzed in detail by using a variety of analytical approaches. Extrusion-like processing conditions were studies in a Closed Cavity Rheometer enabling the application of defined thermal (temperature range 100-160 °C) and mechanical treatments (shear rates between 0.1 s -1 and 50 s -1 ) to chokeberry pomace powder. Application of temperatures up to 140 °C irrespective of the mechanical treatment does not remarkably alter dietary fiber structure or content, but reduces the initial content of total polyphenols by about 40% to a final content of 3.3 ± 0.5 g/100 g including 0.63 ± 0.1 g/100 g of anthocyanins, 0.18 ± 0.02 g/100 g of phenolic acids and 0.090 ± 0.007 g/100 g of flavonols, respectively. The retained polyphenols are fully bioaccessible after in vitro digestion, and antioxidant capacity remains unchanged as compared to the untreated pomace powder. Glucose bioaccessibility remains unaffected, whereas glucose content is reduced. It is concluded that chokeberry pomace powder is a good source of dietary fiber with the potential to partially substitute starch in extruded breakfast cereals., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Protein films can be applied to improve food quality and to reduce packaging waste. To overcome their poor water barrier properties, lipids are often incorporated. The function of incorporated lipid depends on the interface between filler and matrix. This study aimed to tailor the properties of a protein-lipid film by designing the oil/water interface to see if the concept of inactive/active filler is valid. Therefore, we varied the emulsifier stabilizing solid lipid nanoparticles (SLN) to promote (via β-lactoglobulin) or to minimize (via Tween 20) interactions between particle surface and protein. SLN were incorporated into protein films and film properties were determined. Addition of SLN led to significantly decreased water vapor permeability (WVP) of protein films. However, WVP was mainly affected by the emulsifiers and not by the lipid. Protein-stabilized SLN (BS) replaced a lacking protein in the protein network and therefore did not influence the mechanical properties of the films at ambient temperature. BS-composite films were temperature sensitive, as lipid and sucrose palmitate melted at temperatures above 40 °C. Tween 20-stabilized SLN (TS) led to reduced tensile strengths, probably due to perturbative effects of TS and plasticizing effects of Tween 20. Dynamic mechanical analysis showed that TS and Tween 20 increased film mobility. Melting of lipid and emulsifiers, and temperature-dependent behavior of Tween 20 led to a strong temperature dependence of the film stiffness. By designing the interface, particles can be used to tailor mechanical properties of protein films. Tuned edible films could be used to control mass transfers between foods., (© 2019 The Authors. Journal of Food Science published by Wiley Periodicals, Inc. on behalf of Institute of Food Technologists.)

The influence of sucrose palmitate, Tween 20, and lecithin on the properties of heat-induced aggregates and cold-set gels of β-lactoglobulin was studied based on an experimental mixture design with a fixed total emulsifier concentration. Emulsifiers were added to the protein solution before heating. Aggregate size and absolute values of ζ potential increased with the addition of emulsifiers, among which lecithin had the most pronounced effect. The water retention of the aggregates correlated positively with the aggregate size. Gels had reduced fracture stress and strains with increasing sucrose palmitate and decreasing Tween 20 contents. The fracture properties correlated with the ζ potentials of the aggregates, and larger aggregates led to gels with higher water-holding capacities. The emulsifiers hence influenced the gel properties indirectly via the aggregate properties. The impact of emulsifiers on food structures should therefore be considered when a food product is designed.

Bioactive peptides hold great promise as functional ingredients, but they are susceptible to hydrolysis (e.g., protease degradation) during digestion and under different physiological conditions in the human body. Thus, bioactive peptides must be encapsulated first to preserve their innate characteristics and to ensure delivery to an absorption site at the small intestine without biodegradation. The objective of this study was to formulate stable single emulsions of water in oil (W1/O) and double emulsions of water in oil in water (W1/O/W2) containing collagen peptide as core material. In this study, the influence of the following parameters was investigated: collagen peptide concentration (0-20%), salt (0% or 1% NaCl), hydrophilic emulsifiers for the outer water phase (Tween 80, lecithin, chitosan, pectin), and the use of different inner/outer water fractions (20-50% inner water, 50-80% outer water) on the droplet stability of the W1/O and W1/O/W2 emulsions during storage. In particular, the influence of the osmolytes was investigated to evaluate the change in osmotic balance and destabilization of the W1/O/W2 emulsion system as the encapsulated peptide was also osmotically active. Tween 80-stabilized W1/O/W2 emulsions showed the best droplet stability without phase separation (d90,3 = 36.6 μm) and the highest collagen peptide retention (encapsulation efficiency > 90%). During prolonged storage, collagen peptides were released from the W1/O/W2 emulsion system without significant droplet size changes, possibly due to diffusion of the collagen peptide from the inner to the outer water phase. Therefore, our findings can be utilized for preparing stable functional foods or cosmetic products from W1/O/W2 emulsions containing bioactive ingredients.