Search

This paper proposed Tangent Modulus Method (TMM) which is an improved oriented core method to determine in-situ rock stresses. In this approach, the cylindrical specimens prepared along different directions from thick core samples were uniaxially compressed twice to a given stress level. The stress value of the bending point in the first loading cycle of the stress-tangent modulus curve is considered as the normal component of the in-situ rock stress along the drilled direction of the specimen. Four types of rocks from soft porous tuff and sandstone to hard crystalline granite was investigated to evaluate the potential of this method. The effects of changes in strain rate, temperature, water content, confining and pore pressure, and stresses larger than the preload on the stress value of the bending point were experimentally investigated on preload specimens to investigate their influence on TMM. Comparison of the stress measurement results by TMM and an overcoring method at AK tunnel in Hokkaido, Japan was also performed to validate the TMM.

This paper proposed Tangent Modulus Method (TMM) which is an improved oriented core method to determine in-situ rock stresses. In this approach, the cylindrical specimens prepared along different directions from thick core samples were uniaxially compressed twice to a given stress level. The stress value of the bending point in the first loading cycle of the stress-tangent modulus curve is considered as the normal component of the in-situ rock stress along the drilled direction of the specimen. Four types of rocks from soft porous tuff and sandstone to hard crystalline granite was investigated to evaluate the potential of this method. The effects of changes in strain rate, temperature, water content, confining and pore pressure, and stresses larger than the preload on the stress value of the bending point were experimentally investigated on preload specimens to investigate their influence on TMM. Comparison of the stress measurement results by TMM and an overcoring method at AK tunnel in Hokkaido, Japan was also performed to validate the TMM.

M. Kanaoka et al. "Figuring and smoothing capabilities of elastic emission machining for low-thermal-expansion glass optics", Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena 25, 2110-2113 (2007) https://doi.org/10.1116/1.2789440., The use of elastic emission machining (EEM) for fabricating optics from low-thermal-expansion glass for extreme ultraviolet (EUV) lithography is examined. EUV optics require figure accuracy and surface roughness of 0.1 nm root mean square (rms) or better. EEM using a rotating-sphere head is demonstrated to achieve this level of surface smoothness after a certain depth of removal dependent on the material being processed. In tests of continuous machining for 12 h, no increase in surface roughness is observed, demonstrating the high temporal stability of this noncontact processing method. EEM using a rotating-sphere head is thus confirmed to have sufficient figuring and smoothing capability for the fabrication of EUV optics. © 2007 American Vacuum Society.

M. Kanaoka et al. "Figuring and smoothing capabilities of elastic emission machining for low-thermal-expansion glass optics", Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena 25, 2110-2113 (2007) https://doi.org/10.1116/1.2789440., The use of elastic emission machining (EEM) for fabricating optics from low-thermal-expansion glass for extreme ultraviolet (EUV) lithography is examined. EUV optics require figure accuracy and surface roughness of 0.1 nm root mean square (rms) or better. EEM using a rotating-sphere head is demonstrated to achieve this level of surface smoothness after a certain depth of removal dependent on the material being processed. In tests of continuous machining for 12 h, no increase in surface roughness is observed, demonstrating the high temporal stability of this noncontact processing method. EEM using a rotating-sphere head is thus confirmed to have sufficient figuring and smoothing capability for the fabrication of EUV optics. © 2007 American Vacuum Society.

M. Kanaoka et al. "Figuring and smoothing capabilities of elastic emission machining for low-thermal-expansion glass optics", Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena 25, 2110-2113 (2007) https://doi.org/10.1116/1.2789440., The use of elastic emission machining (EEM) for fabricating optics from low-thermal-expansion glass for extreme ultraviolet (EUV) lithography is examined. EUV optics require figure accuracy and surface roughness of 0.1 nm root mean square (rms) or better. EEM using a rotating-sphere head is demonstrated to achieve this level of surface smoothness after a certain depth of removal dependent on the material being processed. In tests of continuous machining for 12 h, no increase in surface roughness is observed, demonstrating the high temporal stability of this noncontact processing method. EEM using a rotating-sphere head is thus confirmed to have sufficient figuring and smoothing capability for the fabrication of EUV optics. © 2007 American Vacuum Society.