Search

Organic aerosol is a highly complex mixture of ∼104 to 105 unique compounds all possessing their own set of physico-chemical properties such as saturation vapour pressure and hygroscopicity.

The airborne transport of bacteria has a wide range of impacts, from disease transmission to cloud formation. By understanding the factors that influence the airborne stability of bacteria, we can better understand these processes.

The dynamics of binary collisions of equi-diameter picolitre droplets with identical viscosities, varying impact speeds and impact angles have been investigated experimentally and compared to collision outcome prediction models. Collisions between pairs of pure water droplets with a viscosity of 0.89 mPa s and pairs of aqueous-sucrose (40% w/w) droplets with a viscosity of 5.17 mPa s were examined. The colliding droplets were ∼38 μm in diameter, which is around ten times smaller than those previously investigated when examining the effect of viscosity on the outcome of binary droplet collisions. Varying the impact speed and angle resulted in different collision outcomes, including coalescence, reflexive separation and stretching separation. The collision outcomes were plotted on two viscosity dependent regime maps. The regime boundaries are generally in agreement with earlier literature for both high and low viscosity cases. The agreement between experiment and theory, for both fluids, gives more confidence in the models tested here to predict collision outcomes for droplets of this size and these viscosities.

The severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic has brought renewed attention to respiratory aerosol and droplet generation. While many studies have robustly quantified aerosol (20 µm diameter) generated by a cohort of 76 adults and children using a water-sensitive paper droplet deposition approach. Unvoiced and voiced activities spanning different levels of loudness, different lengths of sustained phonation, and a specific manner of articulation in isolation were investigated. We find that oral articulation drives >20 µm droplet generation, with breathing generating virtually no droplets and speaking and singing generating on the order of 250 droplets min−1. Lip trilling, which requires extensive oral articulation, generated the most droplets, whereas shouting “Hey,” which requires minimal oral articulation, generated relatively few droplets. Droplet size distributions were all broadly consistent, and no significant differences between the children and adult cohorts were identified. By comparing the aerosol and droplet emissions for the same participants, the full size distribution of respiratory aerosol (0.5–1000 µm) is reported. Although 20 µm droplets dominate the mass concentration. Accurate quantification of aerosol concentrations in the 10–70 μm size range remains very challenging; more robust aerosol analysis approaches are needed to characterize this size range.

SummaryManual facemask ventilation, a core component of elective and emergency airway management, is classified as an aerosol generating procedure. This designation is based on a single epidemiological study suggesting an association between facemask ventilation and transmission from the SARS 2003 outbreak. There is no direct evidence to indicate whether facemask ventilation is a high-risk procedure for aerosol generation. We conducted aerosol monitoring during routine facemask ventilation, and facemask ventilation with an intentionally generated leak, in anaesthetised patients with neuromuscular blockade. Recordings were made in ultraclean theatres and compared against the aerosol generated by the patient’s own tidal breathing and coughs. Respiratory aerosol from tidal breathing was reliably detected above the very low background particle concentrations (191 (77-486 [3.8-1313]) versus 2.1 (0.7-4.6 [0-12.9] particles.l-1 median(IQR)[range], n=11, p=0.002). The average aerosol concentration detected during facemask ventilation both without a leak (3.0 particles.l-1 (0 – 9 [0-43])) and with an intentional leak (11 particles.l-1 (7.0 – 26 [1-62])) was 64-fold and 17-fold lower than that of tidal breathing (p=0.001 and p=0.002 respectively). The peak particle concentration during facemask ventilation both without a leak (60 particles.l-1 (0 – 60 [0-120])) and with a leak (120 particles.l-1 (60 – 180 [60-480]) were respectively 20-fold and 10-fold lower than a cough (1260 particles (800 – 3242 [100-3682]), p=0.002 and p=0.001 respectively). This study demonstrates that facemask ventilation, even performed with an intentional leak, does not generate high levels of bioaerosol. On the basis of this evidence, facemask ventilation should not be considered an aerosol generating procedure.

For many respiratory diseases, a primary mode of transmission is inhalation via aerosols and droplets. The COVID-19 pandemic has accelerated studies of aerosol dispersion in indoor environments. Most studies of aerosol dispersion present computational fluid dynamics results, which rarely include detailed experimental verification, and many of the computations are complex, making them hard to scale to larger spaces. This study presents a comparison of computational simulations and measurements of aerosol dispersion within a typical ventilated classroom. Measurements were accomplished using a custom-built low-cost sensor network composed of 15 commercially available optical particle sizers, which provided size-resolved information about the number concentrations and temporal dynamics of 0.3–40 µm diameter particles. Measurement results are compared to the computed dispersal and loss rates from a steady-state Reynolds-Averaged Navier–Stokes k-epsilon model. The results show that a newly developed aerosol-transport-model can accurately simulate the dispersion of aerosols and faithfully predict measured aerosol concentrations at different locations and times. The computational model was developed with scalability in mind such that it may be adapted for larger spaces. The experiments highlight that the fraction of aerosol recycled in the ventilation system depends on the aerosol droplet size and cannot be predicted by the recycled-to-outside air ratio. Moreover, aerosol recirculation is not negligible, as some computational approaches assume. Both modeling and measurements show that, depending on the location within the room, the maximum aerosol concentration can be many times higher than the average concentration, increasing the risk of infection.

ObjectiveTo determine if oesophago-gastro-duodenoscopy (OGD) generates increased levels of aerosol in conscious patients and identify the source events.DesignA prospective, environmental aerosol monitoring study, undertaken in an ultraclean environment, on patients undergoing OGD. Sampling was performed 20 cm away from the patient’s mouth using an optical particle sizer. Aerosol levels during OGD were compared with tidal breathing and voluntary coughs within subject.ResultsPatients undergoing bariatric surgical assessment were recruited (mean body mass index 44 and mean age 40 years, n=15). A low background particle concentration in theatres (3 L−1) enabled detection of aerosol generation by tidal breathing (mean particle concentration 118 L−1). Aerosol recording during OGD showed an average particle number concentration of 595 L−1with a wide range (3–4320 L−1). Bioaerosol-generating events, namely, coughing or burping, were common. Coughing was evoked in 60% of the endoscopies, with a greater peak concentration and a greater total number of sampled particles than the patient’s reference voluntary coughs (11 710 vs 2320 L−1and 780 vs 191 particles, n=9 and p=0.008). Endoscopies with coughs generated a higher level of aerosol than tidal breathing, whereas those without coughs were not different to the background. Burps also generated increased aerosol concentration, similar to those recorded during voluntary coughs. The insertion and removal of the endoscope were not aerosol generating unless a cough was triggered.ConclusionCoughing evoked during OGD is the main source of the increased aerosol levels, and therefore, OGD should be regarded as a procedure with high risk of producing respiratory aerosols. OGD should be conducted with airborne personal protective equipment and appropriate precautions in those patients who are at risk of having COVID-19 or other respiratory pathogens.

Organic aerosol can adopt a wide range of viscosities, from liquid to glass, depending on the local humidity. In highly viscous droplets, the evaporation rates of organic components are suppressed to varying degrees, yet water evaporation remains fast. Here, we examine the coevaporation of semivolatile organic compounds (SVOCs), along with their solvating water, from aerosol particles levitated in a humidity-controlled environment. To better replicate the composition of secondary aerosol, nonvolatile organics were also present, creating a three-component diffusion problem. Kinetic modeling reproduced the evaporation accurately when the SVOCs were assumed to obey the Stokes-Einstein relation, and water was not. Crucially, our methodology uses previously collected data to constrain the time-dependent viscosity, as well as water diffusion coefficients, allowing it to be predictive rather than postdictive. Throughout the study, evaporation rates were found to decrease as SVOCs deplete from the particle, suggesting path function type behavior.

Pulmonary function tests are fundamental to the diagnosis and monitoring of respiratory diseases. There is uncertainty around whether potentially infectious aerosols are produced during testing and there are limited data on mitigation strategies to reduce risk to staff. Healthy volunteers and patients with lung disease underwent standardised spirometry, peak flow and FENO assessments. Aerosol number concentration was sampled using an aerodynamic particle sizer and an optical particle sizer. Measured aerosol concentrations were compared with breathing, speaking and voluntary coughing. Mitigation strategies included a standard viral filter and a full-face mask normally used for exercise testing (to mitigate induced coughing). 147 measures were collected from 33 healthy volunteers and 10 patients with lung disease. The aerosol number concentration was highest in coughs (1.45–1.61 particles/cm3), followed by unfiltered peak flow (0.37–0.76 particles/cm3). Addition of a viral filter to peak flow reduced aerosol emission by a factor of 10 without affecting the results. On average, coughs produced 22 times more aerosols than standard spirometry (with filter) in patients and 56 times more aerosols in healthy volunteers. FENO measurement produced negligible aerosols. Cardiopulmonary exercise test (CPET) masks reduced aerosol emission when breathing, speaking and coughing significantly. Lung function testing produces less aerosols than voluntary coughing. CPET masks may be used to reduce aerosol emission from induced coughing. Standard viral filters are sufficiently effective to allow guidelines to remove lung function testing from the list of aerosol-generating procedures.

Introduction.Voice assessment and treatment involve the manipulation of all the subsystems of voice production, and may lead to production of respirable aerosol particles that pose a greater risk of potential viral transmission via inhalation of respirable pathogens (e.g. SARS-CoV-2) than quiet breathing or conversational speech. Objective: To characterise the production of respirable aerosol particles during a selection of voice assessment therapy tasks.MethodsWe recruited 23 healthy adult participants (12 males, 11 females), 11 of whom were speech-language pathologists specialising in voice disorders. We used an aerodynamic and optical particle sizer to measure the number concentration and particle size distributions of respirable aerosols generated during a variety of voice assessment and therapy tasks. The measurements were carried out in a laminar flow operating theatre, with a near-zero background aerosol concentration, allowing us to quantify the number concentration and size distributions of respirable aerosol particles produced from assessment/therapy tasks studied. ResultsAerosol number concentrations generated while performing assessment/therapy tasks were log-normally distributed among individuals with no significant differences between professionals (speech-language pathologists) and non-professionals or between males and females. Activities produced up to 32 times the aerosol number concentration of breathing and 24 times that of speech at 70-80 dBA. In terms of aerosol mass, activities produced up to 163 times the mass concentration of breathing and up to 36 times the mass concentration of speech. Voicing was a significant factor in aerosol production; aerosol number/mass concentrations generated during voiced activities were 1.1-5 times higher than their unvoiced counterpart activities. Additionally, voiced activities produced bigger respirable aerosol particles than their unvoiced variants except the trills. Humming generated higher aerosol concentrations than sustained /a/, fricatives, speaking (70-80 dBA), and breathing. Oscillatory semi-occluded vocal tract exercises (SOVTEs) generated higher aerosol number/mass concentrations than activities without oscillation. Water resistance therapy (WRT) generated the most aerosol of all activities, ~10 times higher than speaking at 70-80 dBA and >30 times higher than breathing.ConclusionsAll activities generated more aerosol than breathing, although a sizeable minority were no different to speaking. Larger number concentrations and larger particle sizes appear to be generated by activities with higher suspected airflows, with the greatest involving intraoral pressure oscillation and/or an oscillating oral articulation (WRT or trilling).

Aerosols are highly dynamic, non-equilibrium systems exhibiting unique microphysical properties relative to bulk systems. Here the authors discuss the roles aerosols play in (bio)chemical transformations and identify open questions in aerosol-mediated reaction rate accelerations, aerosol optical properties, and microorganism survival. Aerosols are highly dynamic, non-equilibrium systems exhibiting unique microphysical properties relative to bulk systems. Here the authors discuss the roles aerosols play in (bio)chemical transformations and identify open questions in aerosol-mediated reaction rate accelerations, aerosol optical properties, and microorganism survival.

The evaporation of liquid solution droplets and solute crystallization can be highly complex and is an important problem, particularly in spray drying where powdered products are produced from sprayed liquid droplets, such as in the food or pharmaceutical industries. In this work, we study the relationship between the evaporation rates of single levitated NaNO

Atmospheric water-soluble organic gases such as pyruvic acid are produced in large quantities by photochemical oxidation of biogenic and anthropogenic emissions and undergo water-mediated reactions in aerosols and hydrometeors. These reactions can contribute to aerosol mass by forming less-volatile compounds. Although progress is being made in understanding the relevant aqueous chemistry, little is known about the chemistry that takes place during droplet evaporation. Here, we examine the evaporation of aqueous pyruvic acid droplets using both the vibrating orifice aerosol generator (VOAG) and an electrodynamic balance (EDB). In some cases, pyruvic acid was first oxidized by OH radicals. The evaporation behavior of oxidized mixtures was consistent with expectations based on known volatilities of reaction products. However, independent VOAG and EDB evaporation experiments conducted without oxidation also resulted in stable residual particles; the estimated volume yield was 10–30% of the initial pyruvic acid. Yields varied with temperature and pyruvic acid concentration across cloud-, fog-, and aerosol-relevant concentrations. The formation of low-volatility products, likely cyclic dimers, suggests that pyruvic acid accretion reactions occurring during droplet evaporation could contribute to the gas-to-particle conversion of carbonyls in the atmosphere.

Significance Atmospheric aerosol particles cool Earth’s climate by serving as cloud droplet seeds. This cooling effect represents both the single most uncertain and the largest negative radiative forcing. Cloud droplet activation is strongly influenced by aerosol particle surface tension, which in climate models is assumed equivalent to that of pure water. We directly measure the surface tensions of surfactant-coated, high surface-to-volume ratio droplets, demonstrating that their surface tensions are significantly lower than pure water but do not match the surface tension of the solution from which they were produced and depend on finite droplet size. These results suggest surfactants could potentially significantly modify radiative forcing and highlight the need for a better understanding of atmospheric surfactant concentrations and properties., Surface tension influences the fraction of atmospheric particles that become cloud droplets. Although surfactants are an important component of aerosol mass, the surface tension of activating aerosol particles is still unresolved, with most climate models assuming activating particles have a surface tension equal to that of water. By studying picoliter droplet coalescence, we demonstrate that surfactants can significantly reduce the surface tension of finite-sized droplets below the value for water, consistent with recent field measurements. Significantly, this surface tension reduction is droplet size-dependent and does not correspond exactly to the macroscopic solution value. A fully independent monolayer partitioning model confirms the observed finite-size-dependent surface tension arises from the high surface-to-volume ratio in finite-sized droplets and enables predictions of aerosol hygroscopic growth. This model, constrained by the laboratory measurements, is consistent with a reduction in critical supersaturation for activation, potentially substantially increasing cloud droplet number concentration and modifying radiative cooling relative to current estimates assuming a water surface tension. The results highlight the need for improved constraints on the identities, properties, and concentrations of atmospheric aerosol surfactants in multiple environments and are broadly applicable to any discipline where finite volume effects are operative, such as studies of the competition between reaction rates within the bulk and at the surface of confined volumes and explorations of the influence of surfactants on dried particle morphology from spray driers.

A consensus statement from physicians and scientists with a range of expertise in the areas of respiratory infection and aerosols, to clarify the discussion surrounding a recent preprint (https://www.medrxiv.org/content/10.1101/2022.01.08.22268944v1) describing the aerosol dynamics of SARS-CoV-2 (the virus that causes COVID-19) which generated controversy in mainstream and social media and among infection prevention and control specialists. The study by Oswin et al. is complex and, as such, easily misinterpreted. It must be understood in the context provided by studies of human aerosol emission rates and viral loads in exhaled breath of infected persons, air movement and aerosol transport indoors, previous studies of airborne survival, and epidemiologic studies and outbreak investigations.

Aerosol generating procedures (AGPs) are defined as any procedure releasing airborne particles σ)) and peak positions (DP,C)). The aerosol size distribution provided a robust fingerprint of aerosol emission from a source. 41 patients underwent fifteen different dental procedures. For nine procedures, no aerosol was detected above background. Where aerosol was detected, the percentage of procedure time that aerosol was observed above background ranged from 12.7% for ultrasonic scaling, to 42.9% for 3-in-1 air + water syringe. For ultrasonic scaling, 3-in-1 syringe use and surgical drilling, the aerosol size distribution matched the non-salivary contaminated instrument source, with no unexplained aerosol. High and slow speed drilling produced aerosol from patient procedures with different size distributions to those measured from the phantom head controls (mode widths log(σ)) and peaks (DP,C, p< 0.002) and, therefore, may pose a greater risk of salivary contamination. This study provides evidence for sources of aerosol generation during common dental procedures, enabling more informed evaluation of risk and appropriate mitigation strategies.

Aerosols and droplets generated from expiratory events play a critical role in the transmission of infectious respiratory viruses. Increasingly robust evidence has suggested the crucial role of fine aerosols in airborne transmission of respiratory diseases, which is now widely regarded as an important transmission path of COVID-19. In this report, we used CFD modelling to investigate the efficiency of using portable air purifiers containing HEPA filters to reduce airborne aerosols in hospitals and serve as a potential retrofit mitigation strategy. We used a consulting room to set up our simulations because currently the clearance time between consultations is the controlling factor that limits the patient turnover rate. The results suggest the inlet/suction of the air purifier unit should be lifted above the floor to achieve better clearance efficiency, with up to 40% improvement possible. If multiple air purifiers are used, the combined efficiency can increase to 62%. This work provides practical guidance on a mitigation strategy that can be easily implemented in an expedient, cost-effective and rapid manner, and paves the way for developing more science-informed strategies to mitigate the airborne transmission of respiratory infections in hospitals.

Respiratory particles produced by breathing, coughing, and speaking or generated during medical procedures serve as important routes for disease transmission. Characterising the number of particles generated as well as their size distribution is fundamental for guiding policy on infection control. However, sampling such particles carries inherent challenges. Respiratory particles are polydisperse in size, temporally and spatially variable, and emitted in very low concentrations, usually lower than the pre-existing aerosol concentration in indoor environments. In addition, they are typically emitted in a highly dynamic, warm and humid jet, leading to further rapid processes, such as dispersion and evaporation. Here, we discuss important considerations for sampling respiratory aerosol, focusing on sampling particles < 20 µm in diameter. Instruments capable of counting single-particles within this size range are commercially available. We provide recommendations for experimental protocols and demonstrate the limitations behind such approaches. We highlight the importance of a measurement space with as low a background aerosol concentration as possible, and of sampling for as long as possible to enable accurate quantitation of the size distribution of an aerosol plume. This is particularly important for the larger particles (> 5µm diameter) that are so low in concentration that they may require hours of sampling time to be accurately quantified. We explore the relationship between the flow rates of the exhalation and the sampling instrument and the consequent quantification of particle flux. We also discuss the transport and evaporation dynamics of liquid particles within respiratory jets, and their impacts on conducting aerosol sampling studies.

Aerosol particles of respirable size are exhaled when individuals breathe, speak and sing and can transmit respiratory pathogens between infected and susceptible individuals. The COVID-19 pandemic has brought into focus the need to improve the quantification of the particle number and mass exhalation rates as one route to provide estimates of viral shedding and the potential risk of transmission of viruses. Most previous studies have reported the number and mass concentrations of aerosol particles in an exhaled plume. We provide a robust assessment of the absolute particle number and mass exhalation rates from measurements of minute ventilation using a non-invasive Vyntus Hans Rudolf mask kit with straps housing a rotating vane spirometer along with measurements of the exhaled particle number concentrations and size distributions. Specifically, we report comparisons of the number and mass exhalation rates for children (12–14 years old) and adults (19–72 years old) when breathing, speaking and singing, which indicate that child and adult cohorts generate similar amounts of aerosol when performing the same activity. Mass exhalation rates are typically 0.002–0.02 ng s−1from breathing, 0.07–0.2 ng s−1from speaking (at 70–80 dBA) and 0.1–0.7 ng s−1from singing (at 70–80 dBA). The aerosol exhalation rate increases with increasing sound volume for both children and adults when both speaking and singing.

A refined technique for observing the complete evaporation behaviour of free-falling droplets, from droplet generation to complete solvent evaporation, with ultra-high time resolution is introduced and benchmarked. High-resolution phase-delay stroboscopic imaging is employed to simultaneously resolve the evolving droplet morphology, geometric and aerodynamic diameters, throughout the evaporative lifetime with a user-controlled < μs timescale. This allows rapid, complex morphological changes, such as crystallisation events, to be clearly observed and the corresponding mechanisms to be inferred. The dried particles are sampled for offline SEM analysis and the observed morphologies compared to the inflight imaging. Density changes can be calculated directly from the deviation between the geometric and aerodynamic diameters. The full capabilities of the new technique are demonstrated by examination of the different evaporation behaviours and crystallisation mechanisms for aqueous sodium chloride droplets evaporating under different ambient relative humidity (RH) conditions. The crystallisation window, defined as the time taken from initial to complete crystallisation, is shown to be RH dependent, extending from 0.03 s at 20% RH and 0.13 s at 40% RH. The different crystallisation mechanisms observed during the experiments are also clearly reflected in the final structure of the dry particles, with multi-crystal structures produced at low RH compared to single-crystal structures at higher RH. It is anticipated that this technique will unlock measurements which explore the evaporation behaviour and crystallisation mechanisms for rapid, complex droplet drying events, and with increasingly non-ideal solutions, relevant to industrial applications.

The formation of trileucine-containing spray-dried microparticles intended for pulmonary delivery was studied in depth. A single-particle method was employed to study the shell formation characteristics of trileucine in the presence of trehalose as a glass former, and an empirical correlation was proposed to predict the instance of shell formation. A droplet chain instrument was used to produce and collect monodisperse particles to examine morphology and calculate particle density for different levels of trileucine. It was observed that the addition of only 0.5 mg/mL (10% w/w) trileucine to a trehalose system could lower dried particle densities by approximately 1 g/cm3. In addition, a laboratory-scale spray dryer was used to produce batches of trileucine/trehalose powders in the respirable range. Raman spectroscopy demonstrated that both components were completely amorphous. Scanning electron microscopy and time-of-flight secondary ion mass spectrometry were used to study the particle morphologies and surface compositions. For all cases with trileucine, highly rugose particles with trileucine coverages of more than 60% by mass were observed with trileucine feed fractions of as little as 2% w/w. Moreover, it was seen that at lower trileucine content, smaller and larger particles of a polydisperse powder had slightly different surface compositions. The surface activity of trileucine was also modeled via a modified form of the diffusion equation inside an evaporating droplet that took into account initial surface adsorption and eventual surface desorption due to droplet shrinkage. Finally, using the Flory-Huggins theory, it was estimated that at room temperature, liquid-liquid phase separation would start when the trileucine reached an aqueous concentration of about 18 mg/mL. Besides the surface activity of trileucine, this low concentration was assumed to explain the substantial effect of trileucine on the morphology of spray-dried particles due to early phase separation. The methodology proposed in this study can be used in the rational design of trileucine-containing microparticles.

BackgroundCOVID-19 has restricted singing in communal worship. We sought to understand variations in droplet transmission and the impact of wearing face masks.MethodsUsing rapid laser planar imaging, we measured droplets while participants exhaled, said ‘hello’ or ‘snake’, sang a note or ‘Happy Birthday’, with and without surgical face masks. We measured mean velocity magnitude (MVM), time averaged droplet number (TADN) and maximum droplet number (MDN). Multilevel regression models were used.ResultsIn 20 participants, sound intensity was 71 Decibels (dB) for speaking and 85 dB for singing (p85% reduction wearing face masks. Droplet transmission varied widely, particularly for singing. Masks decreased TADN by 99% (pConclusionsWide variation exists for droplet production. This significantly reduced when wearing face masks. Singing during religious worship wearing a face mask appears as safe as exhaling or talking. This has implications for UK public health guidance during the COVID-19 pandemic.

Aerosol generating procedures (AGPs) are defined as any procedure releasing airborne particles σ)) and peak positions (DP,C)). The aerosol size distribution provided a robust fingerprint of aerosol emission from a source. 41 patients underwent fifteen different dental procedures. For nine procedures, no aerosol was detected above background. Where aerosol was detected, the percentage of procedure time that aerosol was observed above background ranged from 12.7% for ultrasonic scaling, to 42.9% for 3-in-1 air + water syringe. For ultrasonic scaling, 3-in-1 syringe use and surgical drilling, the aerosol size distribution matched the non-salivary contaminated instrument source, with no unexplained aerosol. High and slow speed drilling produced aerosol from patient procedures with different size distributions to those measured from the phantom head controls (mode widths log(σ)) and peaks (DP,C), p< 0.002) and, therefore, may pose a greater risk of salivary contamination. This study provides evidence for sources of aerosol generation during common dental procedures, enabling more informed evaluation of risk and appropriate mitigation strategies.

Gas-particle equilibrium partitioning is a fundamental concept used to describe the growth and loss of secondary organic aerosol (SOA). However, recent literature has suggested that gas-particle partitioning may be kinetically limited, preventing volatilization from the aerosol phase as a result of the physical state of the aerosol (e.g. glassy, viscous). Experimental measurements of diffusion constants within viscous aerosol are limited and do not represent the complex chemical composition observed in SOA (i.e. multicomponent mixtures). Motivated by the need to address fundamental questions regarding the effect of the physical state and chemical composition of a particle on gas-particle partitioning, we present the design and operation of a newly built 0.3 m3 continuous-flow reactor (CFR), which can be used as a tool to gain considerable insights into the composition and physical state of SOA. The CFR was used to generate SOA from the photo-oxidation of α-pinene, limonene, β-caryophyllene and toluene under different experimental conditions (i.e. relative humidity, VOC and VOC∕NOx ratios). Up to 102 mg of SOA mass was collected per experiment, allowing the use of highly accurate compositional- and single-particle analysis techniques, which are not usually accessible due to the large quantity of organic aerosol mass required for analysis. A suite of offline analytical techniques was used to determine the chemical composition and physical state of the generated SOA, including attenuated total reflectance infrared spectroscopy; carbon, hydrogen, nitrogen, and sulfur (CHNS) elemental analysis; 1H and 1H-13C nuclear magnetic resonance spectroscopy (NMR); ultra-performance liquid chromatography ultra-high-resolution mass spectrometry (UHRMS); high-performance liquid chromatography ion-trap mass spectrometry (HPLC-ITMS); and an electrodynamic balance (EDB). The oxygen-to-carbon (O∕C) and hydrogen-to-carbon (H∕C) ratios of generated SOA samples (determined using a CHNS elemental analyser) displayed good agreement with literature values and were consistent with the characteristic Van Krevelen diagram trajectory, with an observed slope of −0.41. The elemental composition of two SOA samples formed in separate replicate experiments displayed excellent reproducibility, with the O∕C and H∕C ratios of the SOA samples observed to be within error of the analytical instrumentation (instrument accuracy ±0.15 % to a reference standard). The ability to use a highly accurate CHNS elemental analyser to determine the elemental composition of the SOA samples allowed us to evaluate the accuracy of reported SOA elemental compositions using UHRMS (a commonly used technique). In all of the experiments investigated, the SOA O∕C ratios obtained for each SOA sample using UHRMS were lower than the O∕C ratios obtained from the CHNS analyser (the more accurate and non-selective technique). The average difference in the ΔO∕C ratios ranged from 19 % to 45 % depending on the SOA precursor and formation conditions. α-pinene SOA standards were generated from the collected SOA mass using semi-preparative HPLC-ITMS coupled to an automated fraction collector, followed by 1H NMR spectroscopy. Up to 35.8±1.6 % (propagated error of the uncertainty in the slope of the calibrations graphs) of α-pinene SOA was quantified using this method; a considerable improvement from most previous studies. Single aerosol droplets were generated from the collected SOA samples and trapped within an EDB at different temperatures and relative humidities to investigate the dynamic changes in their physiochemical properties. The volatilization of organic components from toluene and β-caryophyllene SOA particles at 0 % relative humidity was found to be kinetically limited, owing to particle viscosity. The unconventional use of a newly built CFR, combined with comprehensive offline chemical characterization and single-particle measurements, offers a unique approach to further our understanding of the relationship between SOA formation conditions, chemical composition and physiochemical properties.

The validation of approaches to predict the hygroscopicity of complex mixtures of organic components in aerosol is important for understanding the hygroscopic response of organic aerosol in the atmosphere. We report new measurements of the hygroscopicity of mixtures of dicarboxylic acids and amino acids using a comparative kinetic electrodynamic balance (CK-EDB) approach, inferring the equilibrium water content of the aerosol from close to a saturation relative humidity (100%) down to 80%. We show that the solution densities and refractive indices of the mixtures can be estimated with an accuracy of better than ±2% using the molar refractive index mixing rule and densities and refractive indices for the individual binary organic-aqueous solutions. Further, we show that the often-used mass-, volume-, and mole-weighted mixing rules to estimate the hygroscopicity parameter κ can overestimate the hygroscopic parameter by a factor of as much as 3, highlighting the need to understand the specific nonideal interactions that may arise synergistically in mixtures and cannot be represented by simple models. Indeed, in some extreme cases the hygroscopicity of a multicomponent mixture can be very close to that for the least hygroscopic component. For mixtures of similar components for which no additional synergistic interactions need be considered, the hygroscopicity of the mixed component aerosol can be estimated with high accuracy from the hygroscopic response of the binary aqueous-organic aerosol. In conclusion, we suggest that the hygroscopicity of multicomponent organic aerosol can be highly nonadditive and that simple correlations of hygroscopicity with composition may often misrepresent the level of complexity essential to interpreting aerosol hygroscopicity.

The simultaneous evaporation and condensation of multiple volatile components from multicomponent aerosol droplets leads to changes in droplet size, composition and temperature. Measurements and models that capture and predict these dynamic aerosol processes are key to understanding aerosol microphysics in a broad range of contexts. We report measurements of the evaporation kinetics of droplets (initially ∼25 μm radius) formed from mixtures of ethanol and water levitated within a electrodynamic balance over timescales spanning 500 ms to 6 s. Measurements of evaporation into a gas phase of varied relative humidity and temperature are shown to compare well with predictions from a numerical model. We show that water condensation from the gas phase can occur concurrently with ethanol evaporation from aqueous-ethanol droplets. Indeed, water can condense so rapidly during the evaporation of a pure ethanol droplet in a humid environment, driven by the evaporative cooling the droplet experiences, that the droplet becomes pure water within 0.4 s.

The nosocomial spread of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has focused attention on the risk of aerosol generating procedures (AGPs) in healthcare [1]. SARS-CoV-2 has been isolated from pleural fluid, which has the potential to infect staff or patients if viraemic fluid is aerosolised during procedures [2, 3]. However, evidence for aerosol generation from pleural procedures is very limited. Current guidelines for appropriate use of personal protective equipment (PPE) while performing pleural procedures are based on expert opinion and application of the precautionary principle [4]. We set out to quantify if pleural procedures generated appreciable aerosol (aerosolised liquid particles that have the potential to carry virus) compared to aerosol sampled during normal respiratory activities of breathing and coughing., Percutaneous pleural procedures should not be considered aerosol generating. This study should inform future iterations of guidelines on the appropriate use of PPE when performing these procedures. https://bit.ly/3xFF71d

IntroductionLung function tests are fundamental diagnostic and monitoring tools for patients with respiratory symptoms. There is significant uncertainty around whether potentially infectious aerosol is produced during different lung function testing modalities; and limited data on possible mitigation strategies to reduce risk to staff and limit fallow time.MethodsHealthy volunteers were recruited in an ultraclean, laminar flow theatre and had standardised spirometry as per ERS/ATS guidance, as well as peak flow measurement and FENO assessment of airway inflammation. Aerosol emission was sampled minimum once each second using both an Aerodynamic Particle Sizer (APS) and Optical Particle Sizer (OPS), and compared to breathing, speaking and coughing. Mitigation strategies such as a peak flow viral filter and a CPET facemask (to mitigate induced coughing) were tested.Results33 healthy volunteers were recruited. Aerosol emission was highest in cough (1.61 particles/cm3/sample), followed by unfiltered peak flow (0.76 particles/cm3/sample). Filtered spirometry produced lower peak aerosol emission (0.11 particles/ cm3/sample) than that of a voluntary cough, and addition of a viral filter to the mouthpiece reduced peak flow aerosol emission to similar levels. The filter made little difference to recorded FEV peak flow values. Peak aerosol FENO measurement produced negligible aerosol. Reusable CPET masks with filter reduced aerosol emission when breathing, speaking, and coughing significantly.ConclusionsCompared to voluntary coughing, all lung function testing produced fewer aerosol particles. Filtered spirometry produces lower peak aerosol emission than peak voluntary coughing, and should not be deemed an aerosol generating procedure. The use of viral filters reduces aerosol emission in peak flow by > 10 times, and has little impact on recorded peak flow values. CPET masks are a useful option to reduce aerosol emission from induced coughing while performing spirometry.

The severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic has resulted in an unprecedented shutdown in social and economic activity, with the cultural sector particularly severely affected. Restrictions on musical performances have arisen from a perception that there is a significantly higher risk of aerosol production from singing than speaking, based upon high-profile examples of clusters of COVID-19 following choral rehearsals. However, comparing aerosol generation from different types of vocalization, including singing, across a range of volumes is a rapidly evolving area of research. Here, we measured aerosols from singing, speaking and breathing from a large cohort of 25 professional singers in a range of musical genres in a zero-background environment, allowing unequivocal attribution of aerosol production to specific vocalizations. We do not assess the relative volumes at which people speak and sing. However, both showed steep increases in mass concentration with increase in loudness (spanning a factor of 20–30 across the dynamic range measured, p < 0.001). At the quietest volume (50 to 60 dBA), neither singing (p = 0.19) nor speaking (p = 0.20) were significantly different to breathing. At the loudest volume (90 to 100 dBA), a statistically significant difference (p < 0.001) was observed between singing and speaking, but with singing only generating a factor of between 1.5 and 3.4 more aerosol mass. Guidelines for musical performances should be based on the loudness and duration of the vocalization, the number of participants and the environment in which the activity occurs, rather than the type of vocalization. Mitigations such as the use of amplification and increased attention to ventilation should be employed where practicable. Copyright © 2021 American Association for Aerosol Research

BackgroundRisk of aerosolisation of SARS-CoV-2 directly informs organisation of acute healthcare and PPE guidance. Continuous positive airways pressure (CPAP) and high-flow nasal oxygen (HFNO) are widely used modes of oxygen delivery and respiratory support for patients with severe COVID-19, with both considered as high risk aerosol generating procedures. However, there are limited high quality experimental data characterising aerosolisation during oxygen delivery and respiratory support.MethodsHealthy volunteers were recruited to breathe, speak, and cough in ultra-clean, laminar flow theatres followed by using oxygen and respiratory support systems. Aerosol emission was measured using two discrete methodologies, simultaneously. Hospitalised patients with COVID-19 were also recruited and had aerosol emissions measured during breathing, speaking, and coughing.FindingsIn healthy volunteers (n = 25 subjects; 531 measures), CPAP (with exhalation port filter) produced less aerosols than breathing, speaking and coughing (even with large >50L/m facemask leaks). HFNO did emit aerosols, but the majority of these particles were generated from the HFNO machine, not the patient. HFNO-generated particles were small (InterpretationIn healthy volunteers, CPAP is associated with less aerosol emission than breathing, speaking or coughing. Aerosol emission from the respiratory tract does not appear to be increased by HFNO. Although direct comparisons are complex, cough appears to generate significant aerosols in a size range compatible with airborne transmission of SARS-CoV-2. As a consequence, the risk of SARS-CoV-2 aerosolisation is likely to be high in all areas where patients with Covid-19 are coughing. Guidance on personal protective equipment policy should reflect these updated risks.FundingNIHR-UKRI Rapid COVID call (COV003), Wellcome Trust GW4-CAT Doctoral Training Scheme (FH), MRC CARP Fellowship(JD, MR/T005114/1). Natural Environment Research Council grant (BB, NE/P018459/1)Research in contextEvidence before this studyPubMed was searched from inception until 10/1/21 using the terms ‘aerosol’, and variations of ‘non-invasive positive pressure ventilation’ and ‘high-flow nasal oxygen therapy’. Studies were included if they measured aerosol generated from volunteers or patients receiving non-invasive positive pressure ventilation (NIV) or high flow nasal oxygen therapy (HFNO), or provided experimental evidence on a simulated human setting. One study was identified (Gaeckle et al, 2020) which measured aerosol emission with one methodology (APS) but was limited by high background concentration of aerosol and a low number of participants (n = 10).Added value of this studyThis study used multiple methodologies to measure aerosol emission from the respiratory tract before and during CPAP and high-flow nasal oxygen, in an ultra-clean, laminar flow theatre with near-zero background aerosol and recruited patients with COVID-19 to ensure similar aerosol distributions. We conclude that there is negligible aerosol generation with CPAP, that aerosol emission from HFNO is from the machine and not the patient, coughing emits aerosols consistent with airborne transmission of SARS CoV2 and that healthy volunteers are a reasonable proxy for COVID-19 patients.Implications of all the available evidenceCPAP and HFNO should not be considered high risk aerosol generating procedures, based on our study and that of Gaeckle et al. Recorded aerosol emission from HFNO stems from the machine. Cough remains a significant aerosol risk. PPE guidance should be updated to ensure medical staff are protected with appropriate PPE in situations when patients with suspected or proven COVID-19 are likely to cough.

The substance Tris (or THAM, 2-amino-2-hydroxymethyl-1,3-propanediol) is used in the preparation of pH buffer solutions for applications in natural water chemistry, including seawater. The development of a chemical speciation model of buffer solutions containing Tris, TrisH+, and the major ions of seawater is desirable, so that the effects of changes in the composition and concentration of the medium on pH can be calculated. The Pitzer activity coefficient equations, commonly used in such speciation models, describe the thermodynamic properties of solutions in terms of interactions between dissolved ions and uncharged solute species. To determine some of these interactions, we have measured solubilities of Tris(s) in water and aqueous solutions of NaCl, TrisHCl, and (TrisH)2SO4 and the solubility of NaCl(s) in aqueous Tris(aq), from 5 to 45 °C. We report measurements of the water activities of Tris solutions at 293.5 K to high supersaturation with respect to the solid. Using the Pitzer equations, we compare our results to literature data yielding stoichiometric dissociation constants of TrisH+ in aqueous NaCl, and to electromotive forces of cells containing dissolved Tris, TrisHCl, and NaCl. Values of parameters for the interactions of Tris with the ions TrisH+, Na+, and SO42- at 25 °C are determined. The work of P.L. and E.P.A. was supported by the Helmholtz Association. The work of S.L.C. was supported by the Natural Environment Council of the UK, award number NE/P012361/1 under the joint NERC/NSF:GEO scheme. Authors F.K.A.G. and J.P.R. were supported by the Engineering and Physical Sciences Research Council under the grant code EP/N025245/1. This publication is a contribution of SCOR Working Group 145 (SCOR is the Scientific Committee on Oceanic Research) and of the Joint Committee on Seawater, which is sponsored by SCOR, the International Association for the Properties of Water and Steam, and the International Association for the Physical Sciences of the Oceans. The work of WG 145 presented in this article results, in part, from funding provided by national committees of SCOR and from a grant to SCOR from the U.S. National Science Foundation (OCE-1840868).

Aerosols and droplets from expiratory events play an integral role in transmitting pathogens such as SARS-CoV-2 from an infected individual to a susceptible host. However, there remain significant uncertainties in our understanding of the aerosol droplet microphysics occurring during drying and sedimentation and the effect on the sedimentation outcomes. Here, we apply a new treatment for the microphysical behavior of respiratory fluid droplets to a droplet evaporation/sedimentation model and assess the impact on sedimentation distance, time scale, and particle phase. Above a 100 μm initial diameter, the sedimentation outcome for a respiratory droplet is insensitive to composition and ambient conditions. Below 100 μm, and particularly below 80 μm, the increased settling time allows the exact nature of the evaporation process to play a significant role in influencing the sedimentation outcome. For this size range, an incorrect treatment of the droplet composition, or imprecise use of RH or temperature, can lead to large discrepancies in sedimentation distance (with representative values >1 m, >2 m, and >2 m, respectively). Additionally, a respiratory droplet is likely to undergo a phase change prior to sedimenting if initially, Accurate, experimentally derived microphysical treatments of respiratory fluid droplets enable the robust modeling of sedimentation outcomes.

The performing arts have been significantly restricted due to the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) pandemic. We report measurements of aerosol and droplet concentrations generated when playing woodwind and brass instruments and comparisons with breathing, speaking, and singing. These measurements were conducted in a room with zero number concentration aerosol background in the 0.5-20 µm diameter size range, allowing clear attribution of detected particles to specific activities. A total of 13 instruments were examined across 9 participants. Respirable particle number concentrations and size distributions for playing instruments are consistent with those from the participant when breathing, based on measurements with multiple participants playing the flute and piccolo as well as measurements across the entire cohort. Due to substantial interparticipant variability, we do not provide a comparative assessment of the aerosol generated by playing different instruments, instead considering only the variation in aerosol yield across all instruments studied. Both particle number and mass concentrations from playing instruments are lower than those from speaking and singing at high volume, and no large droplets >20 µm diameter are detected. Combined, these observations suggest that playing instruments generates less aerosol than speaking or singing at high volumes. Moreover, there is no difference between the aerosol concentrations generated by professional and amateur performers while breathing, speaking, or singing, suggesting conclusions for professional singers may also apply to amateurs.