Search

Graphene Hall-effect magnetic field sensors (GHSs) exhibit high performance comparable to state-of-the-art commercial Hall sensors made from III-V semiconductors. Graphene is also amenable to CMOS-compatible fabrication processes, making GHSs attractive candidates for implementing magnetic sensor arrays for imaging fields in biosensing and scanning probe applications. However, their practical appeal is limited by response heterogeneity and drift, arising from the high sensitivity of two-dimensional (2D) materials to local device imperfections. To address this challenge, we designed a GHS array in which an individual backgate is added to each GHS, allowing the carrier density of each sensor to be electrostatically tuned independent of other sensors in the array. Compared to the constraints encountered when all devices are tuned with the same backgate, we expected that the flexibility afforded by individual tuning would allow for the array's sensitivity, uniformity, and reconfigurability to be enhanced. We fabricated an array of 16 GHSs, each with its own backgate terminal, and characterized the ability to modulate GHS carrier density and Hall sensitivity within CMOS-compatible voltage ranges. We then demonstrated that individual device tuning can be used to break the trade-off between device sensitivity and uniformity in the GHS array, allowing for enhancement of both objectives. Our results showed that GHS arrays exhibiting >30% variability under single-backgate operation could be compensated using individual tuning to achieve <2% variability with minimal impact on the array sensitivity.

Oligonucleotide-functionalized graphene biosensors show immense promise for use as label-free point of care devices for detection of nucleic acid biomarkers at clinically relevant levels. Graphene-based nucleic acid sensors can be fabricated at low cost and have been shown to reach limits of detection in the attomolar range. Here we demonstrate devices functionalized with 22mer or 8omer DNA probes are capable of detecting full length genomic HIV-1 subtype B RNA, with a limit of detection below 1 aM in nuclease free water. We also show that these sensors are suitable for detection directly in Qiazol lysis reagent, again with a limit of detection below 1 aM for both 22mer and 8omer probes., Competing Interests: Declaration of interests The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

We characterize the effect of ferromagnetic nickel nanoparticles (size ∼6 nm) on the magnetotransport properties of chemical-vapor-deposited (CVD) graphene. The nanoparticles were formed by thermal annealing of a thin Ni film evaporated on top of a graphene ribbon. The magnetoresistance was measured while sweeping the magnetic field at different temperatures, and compared against measurements performed on pristine graphene. Our results show that, in the presence of Ni nanoparticles, the usually observed zero-field peak of resistivity produced by weak localization is widely suppressed (by a factor of ∼3), most likely due to the reduction of the dephasing time as a consequence of the increase in magnetic scattering. On the other hand, the high-field magnetoresistance is amplified by the contribution of a large effective interaction field. The results are discussed in terms of a local exchange coupling, J∼6 meV, between the graphene π electrons and the 3d magnetic moment of nickel. Interestingly, this magnetic coupling does not affect the intrinsic transport parameters of graphene, such as the mobility and transport scattering rate, which remain the same with and without Ni nanoparticles, indicating that the changes in the magnetotransport properties have a purely magnetic origin.

We report on transport measurements in monolayer MoS 2 devices, close to the bottom of the conduction band edge. These devices were annealed in situ before electrical measurements. This allows us to obtain good ohmic contacts at low temperatures, and to measure precisely the conductivity and mobility via four-probe measurements. The measured effective mobility up to μ eff = 180 cm 2 V -1 s -1 is among the largest obtained in CVD-grown MoS 2 monolayer devices. These measurements show that electronic transport is of the insulating type for σ ≤ 1.4 e 2 / h and n ≤ 1.7 × 10 12 cm -2 , and a crossover to a metallic regime is observed above those values. In the insulating regime, thermally activated transport dominates at high temperature ( T > 120 K). At lower temperatures, conductivity is driven by Efros-Schklovkii variable range hopping in all measured devices, with a universal and constant hopping prefactor, that is a clear indication that hopping is not phonon-mediated. At higher carrier density, and high temperature, the conductivity is well modeled by the Boltzmann equation for a non-interacting Fermi gas, taking into account both phonon and impurity scatterings. Finally, even if this apparent metal-insulator transition can be explained by phonon-related phenomena at high temperature, the possibility of a genuine 2D MIT cannot be ruled out, as we can observe a clear power-law diverging localization length close to the transition, and a one-parameter scaling can be realized., (© 2023 IOP Publishing Ltd.)

Integrated phononics plays an important role in both fundamental physics and technology. Despite great efforts, it remains a challenge to break time-reversal symmetry to achieve topological phases and non-reciprocal devices. Piezomagnetic materials offer an intriguing opportunity as they break time-reversal symmetry intrinsically, without the need for an external magnetic field or an active driving field. Moreover, they are antiferromagnetic, and possibly compatible with superconducting components. Here, we develop a theoretical framework that combines linear elasticity with Maxwell's equations via piezoelectricity and/or piezomagnetism beyond the commonly adopted quasi-static approximation. Our theory predicts and numerically demonstrates phononic Chern insulators based on piezomagnetism. We further show that the topological phase and chiral edge states in this system can be controlled by the charge doping. Our results exploit a general duality relation between piezoelectric and piezomagnetic systems, which can potentially be generalized to other composite metamaterial systems., (© 2023. The Author(s).)

Since the beginning of the COVID-19 pandemic, there has been enormous interest in the development of measures that would allow for the swift detection of the disease. The rapid screening and preliminary diagnosis of SARS-CoV-2 infection allow for the instant identification of possibly infected individuals and the subsequent mitigation of the disease spread. Herein, the detection of SARS-CoV-2-infected individuals was explored using noninvasive sampling and low-preparatory-work analytical instrumentation. Hand odor samples were obtained from SARS-CoV-2-positive and -negative individuals. The volatile organic compounds (VOCs) were extracted from the collected hand odor samples using solid phase microextraction (SPME) and analyzed using gas chromatography coupled with mass spectrometry (GC-MS). Sparse partial least squares discriminant analysis (sPLS-DA) was used to develop predictive models using the suspected variant sample subsets. The developed sPLS-DA models performed moderately (75.8% (±0.4) accuracy, 81.8% sensitivity, 69.7% specificity) at distinguishing between SARS-CoV-2-positive and negative -individuals based on the VOC signatures alone. Potential markers for distinguishing between infection statuses were preliminarily acquired using this multivariate data analysis. This work highlights the potential of using odor signatures as a diagnostic tool and sets the groundwork for the optimization of other rapid screening sensors such as e-noses or detection canines.

The spread of SARS-CoV-2, which causes the disease COVID-19, is difficult to control as some positive individuals, capable of transmitting the disease, can be asymptomatic. Thus, it remains critical to generate noninvasive, inexpensive COVID-19 screening systems. Two such methods include detection canines and analytical instrumentation, both of which detect volatile organic compounds associated with SARS-CoV-2. In this study, the performance of trained detection dogs is compared to a noninvasive headspace-solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS) approach to identifying COVID-19 positive individuals. Five dogs were trained to detect the odor signature associated with COVID-19. They varied in performance, with the two highest-performing dogs averaging 88% sensitivity and 95% specificity over five double-blind tests. The three lowest-performing dogs averaged 46% sensitivity and 87% specificity. The optimized linear discriminant analysis (LDA) model, developed using HS-SPME-GC-MS, displayed a 100% true positive rate and a 100% true negative rate using leave-one-out cross-validation. However, the non-optimized LDA model displayed difficulty in categorizing animal hair-contaminated samples, while animal hair did not impact the dogs' performance. In conclusion, the HS-SPME-GC-MS approach for noninvasive COVID-19 detection more accurately discriminated between COVID-19 positive and COVID-19 negative samples; however, dogs performed better than the computational model when non-ideal samples were presented.

Hippocampal seizures are a defining feature of mesial temporal lobe epilepsy (MTLE). Area CA1 of the hippocampus is commonly implicated in the generation of seizures, which may occur because of the activity of endogenous cell populations or of inputs from other regions within the hippocampal formation. Simultaneously observing activity at the cellular and network scales in vivo remains challenging. Here, we present a novel technology for simultaneous electrophysiology and multicellular calcium imaging of CA1 pyramidal cells (PCs) in mice enabled by a transparent graphene-based microelectrode array (Gr MEA). We examine PC firing at seizure onset, oscillatory coupling, and the dynamics of the seizure traveling wave as seizures evolve. Finally, we couple features derived from both modalities to predict the speed of the traveling wave using bootstrap aggregated regression trees. Analysis of the most important features in the regression trees suggests a transition among states in the evolution of hippocampal seizures., (Copyright © 2022 Mulcahey et al.)

The strain in hybrid van der Waals heterostructures, made of two distinct two-dimensional van der Waals materials, offers an interesting handle on their corresponding electronic band structure. Such strain can be engineered by changing the relative crystallographic orientation between the constitutive monolayers, notably, the angular misorientation, also known as the "twist angle". By combining angle-resolved photoemission spectroscopy with density functional theory calculations, we investigate here the band structure of the WS 2 /graphene heterobilayer for various twist angles. Despite the relatively weak coupling between WS 2 and graphene, we demonstrate that the resulting strain quantitatively affects many electronic features of the WS 2 monolayers, including the spin-orbit coupling strength. In particular, we show that the WS 2 spin-orbit splitting of the valence band maximum at K can be tuned from 430 to 460 meV. Our findings open perspectives in controlling the band dispersion of van der Waals materials.

We present experimental evidence of electronic and optical interlayer resonances in graphene van der Waals heterostructure interfaces. Using the spectroscopic mode of a low-energy electron microscope (LEEM), we characterized these interlayer resonant states up to 10 eV above the vacuum level. Compared with nontwisted, AB-stacked bilayer graphene (AB BLG), an ≈0.2  Å increase was found in the interlayer spacing of 30° twisted bilayer graphene (30°-tBLG). In addition, we used Raman spectroscopy to probe the inelastic light-matter interactions. A unique type of Fano resonance was found around the D and G modes of the graphene lattice vibrations. This anomalous, robust Fano resonance is a direct result of quantum confinement and the interplay between discrete phonon states and the excitonic continuum.

The large-scale growth of semiconducting thin films on insulating substrates enables batch fabrication of atomically thin electronic and optoelectronic devices and circuits without film transfer. Here an efficient method to achieve rapid growth of large-area monolayer MoSe 2 films based on spin coating of Mo precursor and assisted by NaCl is reported. Uniform monolayer MoSe 2 films up to a few inches in size are obtained within a short growth time of 5 min. The as-grown monolayer MoSe 2 films are of high quality with large grain size (up to 120 μm). Arrays of field-effect transistors are fabricated from the MoSe 2 films through a photolithographic process; the devices exhibit high carrier mobility of ≈27.6 cm 2 V -1 s -1 and on/off ratios of ≈10 5 . The findings provide insight into the batch production of uniform thin transition metal dichalcogenide films and promote their large-scale applications., Competing Interests: Conflict of Interest The authors declare no conflict of interest.

Several water-soluble variants of the human mu opioid receptor (wsMORs) have been designed and expressed, which enables the detection of opioids in the nM to pM range using biosensing platforms. The tools previously developed allowed us to investigate MOR and G-protein interactions in a lipid free system to demonstrate that the lipid bilayer might not be essential for the G-protein recognition and binding. In this study, we are able to investigate G-protein interactions with MOR by using graphene enabled technology, in a lipid free system, with a high sensitivity in a real time manner. A new wsMOR with the native C-terminus was designed, expressed and then immobilized on the surfaces of scalable graphene field effect transistor (GFET)-based biosensors, enabling the recording of wsMOR/G-protein interaction with an electronic readout. G-protein only interacts with the wsMOR in the presence of the native MOR C-terminus with a K A of 32.3±11.1 pM. The electronic readout of such interaction is highly reproducible with little variance across 50 devices in one biosensor array. For devices with receptors that do not have the native C-terminus, no significant electronic response was observed in the presence of G-protein, indicating an absence of interaction. These findings reveal that lipid environment is not essential for the G-protein interaction with MOR, however, the C-terminus of MOR is essential for G-protein recognition and high affinity binding. A system to detect MOR-G protein interaction is developed. wsMOR-G2&#95;Cter provides a novel tool to investigate the role of C terminus in the signaling pathway.

Neurological disorders such as epilepsy arise from disrupted brain networks. Our capacity to treat these disorders is limited by our inability to map these networks at sufficient temporal and spatial scales to target interventions. Current best techniques either sample broad areas at low temporal resolution (e.g. calcium imaging) or record from discrete regions at high temporal resolution (e.g. electrophysiology). This limitation hampers our ability to understand and intervene in aberrations of network dynamics. Here we present a technique to map the onset and spatiotemporal spread of acute epileptic seizures in vivo by simultaneously recording high bandwidth microelectrocorticography and calcium fluorescence using transparent graphene microelectrode arrays. We integrate dynamic data features from both modalities using non-negative matrix factorization to identify sequential spatiotemporal patterns of seizure onset and evolution, revealing how the temporal progression of ictal electrophysiology is linked to the spatial evolution of the recruited seizure core. This integrated analysis of multimodal data reveals otherwise hidden state transitions in the spatial and temporal progression of acute seizures. The techniques demonstrated here may enable future targeted therapeutic interventions and novel spatially embedded models of local circuit dynamics during seizure onset and evolution.

Despite extensive research on the tribological properties of MoS 2 , the frictional characteristics of other members of the transition-metal dichalcogenide (TMD) family have remained relatively unexplored. To understand the effect of the chalcogen on the tribological behavior of these materials and gain broader general insights into the factors controlling friction at the nanoscale, we compared the friction force behavior for a nanoscale single asperity sliding on MoS 2 , MoSe 2 , and MoTe 2 in both bulk and monolayer forms through a combination of atomic force microscopy experiments and molecular dynamics simulations. Experiments and simulations showed that, under otherwise identical conditions, MoS 2 has the highest friction among these materials and MoTe 2 has the lowest. Simulations complemented by theoretical analysis based on the Prandtl-Tomlinson model revealed that the observed friction contrast between the TMDs was attributable to their lattice constants, which differed depending on the chalcogen. While the corrugation amplitudes of the energy landscapes are similar for all three materials, larger lattice constants permit the tip to slide more easily across correspondingly wider saddle points in the potential energy landscape. These results emphasize the critical role of the lattice constant, which can be the determining factor for frictional behavior at the nanoscale.

Semiconducting monolayers of a 2D material are able to concatenate multiple interesting properties into a single component. Here, by combining opto-mechanical and electronic measurements, we demonstrate the presence of a partial 2H-1T' phase transition in a suspended 2D monolayer membrane of MoS 2 . Electronic transport shows unexpected memristive properties in the MoS 2 membrane, in the absence of any external dopants. A strong mechanical softening of the membrane is measured concurrently and may only be related to the 2H-1T' phase transition, which imposes a 3% directional elongation of the topological 1T' phase with respect to the semiconducting 2H. We note that only a few percent 2H-1T' phase switching is sufficient to observe measurable memristive effects. Our experimental results combined with first-principles total energy calculations indicate that sulfur vacancy diffusion plays a key role in the initial nucleation of the phase transition. Our study clearly shows that nanomechanics represents an ultrasensitive technique to probe the crystal phase transition in 2D materials or thin membranes. Finally, a better control of the microscopic mechanisms responsible for the observed memristive effect in MoS 2 is important for the implementation of future devices.

A water-soluble variant of the transmembrane domain of the human mu opioid receptor (wsMOR-TM) was previously characterized. This study explored whether the full-length version of the engineered water-soluble receptor, (wsMOR-FL), could be overexpressed in Escherichia coli and if it would retain water solubility, binding capability and thermostability. wsMOR was over-expressed and purified in E. coli BL21(DE3) cells (EMD/Novagen) as we reported previously for the wsMOR-TM. Both native N and C termini were added back to the highly engineered wsMOR-TM. Six His-tag was added in the N terminus for purification purposes. The wsMOR-FL was characterized using atomic force microscope for its monomeric state, circular dichroism for its secondary structure and thermostability. Its binding with naltrexone is also determined. Compared to the native human MOR, wsMOR-FL displays similar helical secondary structure content and comparable affinity (nM) for the antagonist naltrexone. The secondary structure of the receptor remains stable within a wide range of pH (6-9). In contrast to the transmembrane portion, the secondary structure of full-length receptor tolerated a wide range of temperature (10-90 °C). The receptor remains predominantly as a monomer in solution, as directly imaged using atomic force microscopy. This study demonstrated that functional full-length water-soluble variant of human mu receptor can be over-expressed and purified using an E. coli over-expression system. This provides a novel tool for the investigation of structural and functional properties of the human MOR. N- and C-termini strengthened the thermostability of the protein in this specific water soluble variant. Communicated by Ramaswamy H. Sarma.

The properties of van der Waals (vdW) materials often vary dramatically with the atomic stacking order between layers, but this order can be difficult to control. Trilayer graphene (TLG) stacks in either a semimetallic ABA or a semiconducting ABC configuration with a gate-tunable band gap, but the latter has only been produced by exfoliation. Here we present a chemical vapor deposition approach to TLG growth that yields greatly enhanced fraction and size of ABC domains. The key insight is that substrate curvature can stabilize ABC domains. Controllable ABC yields ~59% were achieved by tailoring substrate curvature levels. ABC fractions remained high after transfer to device substrates, as confirmed by transport measurements revealing the expected tunable ABC band gap. Substrate topography engineering provides a path to large-scale synthesis of epitaxial ABC-TLG and other vdW materials.

Owing to their unique electrical and optical properties, two-dimensional transition metal dichalcogenides have been extensively studied for their potential applications in biosensing. However, simultaneous utilization of both optical and electrical properties has been overlooked, yet it can offer enhanced accuracy and detection versitility. Here, we demonstrate a dual-mode optoelectronic biosensor based on monolayer molybdenum disulfide (MoS 2 ) capable of producing simultaneous electrical and optical readouts of biomolecular signals. On a single platform, the biosensor exhibits a tunable photonic Fano-type optical resonance while also functioning as a field-effect transistor (FET) based on a optically transparent gate electrode. Furthermore, chemical vapor deposition grown MoS 2 provides a clean surface for direct immobilization of a water-soluble variant of the μ -opioid receptor (wsMOR), via a nickel ion-mediated linker chemistry. We utilize a synthetic opioid peptide to show the operation of the electronic and optical sensing modes. The responses of both modes exhibit a similar trend with dynamic ranges of four orders of magnitude and detection limits of <1 nM. Our work explores the potential of a versatile multimodal sensing platform enabled by monolayer MoS 2 , since the integration of electrical and optical sensors on the same chip can offer flexibility in read-out and improve the accuracy in detection of low concentration targets.

Two-dimensional (2D) van der Waals superlattices comprised of two stacked monolayer materials have attracted significant interest as platforms for novel optoelectronic and structural behavior. Although studies are focused on superlattice fabrication, less effort has been given to the nanoscale patterning and structural modification of these systems. In this report, we demonstrate the localized layer-by-layer thinning and formation of nanopores/defects in 2D superlattices, such as stacked MoS 2 -WS 2 van der Waals heterostructures and chemical vapor deposited bilayer WSe 2 , using aberration-corrected scanning transmission electron microscopy (STEM). Controlled electron beam irradiation is used to locally thin superlattices by removing the bottom layer of atoms, followed by defect formation through ablation of the second layer of atoms. The resulting defects exhibit atomically-sharp pore edges with tunable diameters down to 0.6 nm. Structural periodicities and focused STEM irradiation are also utilized to form close-packed nanopore arrays in superlattices with varying twist angles and commensurability. Applying these methods and mechanisms provides a forward approach in the atomic-scale patterning of stacked 2D nanodevices.

Bilayer two-dimensional (2D) van der Waals (vdW) materials are attracting increasing attention due to their predicted high quality electronic and optical properties. Here, we demonstrate dense, selective growth of WSe 2 bilayer flakes by chemical vapor deposition with the use of a 1:10 molar mixture of sodium cholate and sodium chloride as the growth promoter to control the local diffusion of W-containing species. A large fraction of the bilayer WSe 2 flakes showed a 0 (AB) and 60° (AA') twist between the two layers, whereas Moiré 15 and 30° twist angles were also observed. Well-defined monolayer-bilayer junctions were formed in the as-grown bilayer WSe 2 flakes, and these interfaces exhibited p-n diode rectification and an ambipolar transport characteristic. This work provides an efficient method for the layer-controlled growth of 2D materials, in particular, 2D transition metal dichalcogenides, and promotes their applications in next-generation electronic and optoelectronic devices.

Ultralow friction can be achieved with 2D materials, particularly graphene and MoS 2 . The nanotribological properties of these different 2D materials have been measured in previous atomic force microscope (AFM) experiments sequentially, precluding immediate and direct comparison of their frictional behavior. Here, friction is characterized at the nanoscale using AFM experiments with the same tip sliding over graphene, MoS 2 , and a graphene/MoS 2 heterostructure in a single measurement, repeated hundreds of times, and also measured with a slowly varying normal force. The same material systems are simulated using molecular dynamics (MD) and analyzed using density functional theory (DFT) calculations. In both experiments and MD simulations, graphene consistently exhibits lower friction than the MoS 2 monolayer and the heterostructure. In some cases, friction on the heterostructure is lower than that on the MoS 2 monolayer. Quasi-static MD simulations and DFT calculations show that the origin of the friction contrast is the difference in energy barriers for a tip sliding across each of the three surfaces.

This article will briefly overview our efforts in the engineering of water soluble variants of a G-protein coupled receptor (GPCR) and its novel applications to develop biosensors using such water soluble variants of GPCR. While the technologies using water soluble GPCR are still under development, they offer new tools and strategies to study the function of GPCR, explore potential new compounds for potential clinical usage, and monitor endogenous peptides in various physiological and pathological conditions.

Arrays of DNA-functionalized graphene field-effect transistors (gFETs) hold great promise for high-performance vapor sensing. In this chapter, we describe methods for the scalable production of gFET-based vapor sensors with high sensitivity and efficiency in size, cost, and time. Large-area graphene sheets were prepared via chemical vapor deposition (CVD); a standard photolithographic processing for large-area graphene was used to fabricate gFETs with high mobility and low doping level under ambient conditions. The gFETs were functionalized by single-stranded DNA (ssDNA), which binds to the graphene channels through π-π stacking interaction and provides affinity to a wide range of chemical vapors. The resulting sensing arrays demonstrate detection of target vapor molecules down to parts-per-million concentrations with high selectivity among analytes with high chemical similarity including a series of carboxylic acids and structural isomers of carboxylic acids and pinene.

Two-dimensional molybdenum-disulfide (MoS2) catalysts can achieve high catalytic activity for the hydrogen evolution reaction upon appropriate modification of their surface. The intrinsic inertness of the compound's basal planes can be overcome by either increasing the number of catalytically active edge sites or by enhancing the activity of the basal planes via a controlled creation of sulfur vacancies. Here, we report a novel method of activating the MoS2 surface using swift heavy ion irradiation. The creation of nanometer-scale structures by an ion beam, in combination with the partial sulfur depletion of the basal planes, leads to a large increase of the number of low-coordinated Mo atoms, which can form bonds with adsorbing species. This results in a decreased onset potential for hydrogen evolution, as well as in a significant enhancement of the electrochemical current density by over 160% as compared to an identical but non-irradiated MoS2 surface.

Electronic DNA-biosensor with a single nucleotide resolution capability is highly desirable for personalized medicine. However, existing DNA-biosensors, especially single nucleotide polymorphism (SNP) detection systems, have poor sensitivity and specificity and lack real-time wireless data transmission. DNA-tweezers with graphene field effect transistor (FET) are used for SNP detection and data are transmitted wirelessly for analysis. Picomolar sensitivity of quantitative SNP detection is achieved by observing changes in Dirac point shift and resistance change. The use of DNA-tweezers probe with high-quality graphene FET significantly improves analytical characteristics of SNP detection by enhancing the sensitivity more than 1000-fold in comparison to previous work. The electrical signal resulting from resistance changes triggered by DNA strand-displacement and related changes in the DNA geometry is recorded and transmitted remotely to personal electronics. Practical implementation of this enabling technology will provide cheaper, faster, and portable point-of-care molecular health status monitoring and diagnostic devices., (© 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

All-electronic DNA biosensors based on graphene field-effect transistors (GFETs) offer the prospect of simple and cost-effective diagnostics. For GFET sensors based on complementary probe DNA, the sensitivity is limited by the binding affinity of the target oligonucleotide, in the nM range for 20 mer targets. We report a ∼20 000× improvement in sensitivity through the use of engineered hairpin probe DNA that allows for target recycling and hybridization chain reaction. This enables detection of 21 mer target DNA at sub-fM concentration and provides superior specificity against single-base mismatched oligomers. The work is based on a scalable fabrication process for biosensor arrays that is suitable for multiplexed detection. This approach overcomes the binding-affinity-dependent sensitivity of nucleic acid biosensors and offers a pathway toward multiplexed and label-free nucleic acid testing with high accuracy and selectivity.

Opioid neuropeptides play a significant role in pain perception, appetite regulation, sleep, memory, and learning. Advances in understanding of opioid peptide physiology are held back by the lack of methodologies for real-time quantification of affinities and kinetics of the opioid neuropeptide-receptor interaction at levels typical of endogenous secretion (<50 pM) in biosolutions with physiological ionic strength. To address this challenge, we developed all-electronic opioid-neuropeptide biosensors based on graphene microelectrodes functionalized with a computationally redesigned water-soluble μ-opioid receptor. We used the functionalized microelectrode in a bias-free charge measurement configuration to measure the binding kinetics and equilibrium binding properties of the engineered receptor with [d-Ala 2 , N-MePhe 4 , Gly-ol]-enkephalin and β-endorphin at picomolar levels in real time.

Semiconducting two-dimensional (2D) materials, such as transition-metal dichalcogenides (TMDs), are emerging in nanomechanics, optoelectronics, and thermal transport. In each of these fields, perfect control over 2D material properties including strain, doping, and heating is necessary, especially on the nanoscale. Here, we study clean devices consisting of membranes of single-layer MoS 2 suspended on pillar arrays. Using Raman and photoluminescence spectroscopy, we have been able to extract, separate, and simulate the different contributions on the nanoscale and to correlate these to the pillar array design. This control has been used to design a periodic MoS 2 mechanical membrane with a high reproducibility and to perform optomechanical measurements on arrays of similar resonators with a high-quality factor of 600 at ambient temperature, hence opening the way to multiresonator applications with 2D materials. At the same time, this study constitutes a reference for the future development of well-controlled optical emissions within 2D materials on periodic arrays with reproducible behavior. We measured a strong reduction of the MoS 2 band gap induced by the strain generated from the pillars. A transition from direct to indirect band gap was observed in isolated tent structures made of MoS 2 and pinched by a pillar. In fully suspended devices, simulations were performed allowing both the extraction of the thermal conductance and doping of the layer. Using the correlation between the influences of strain and doping on the MoS 2 Raman spectrum, we have developed a simple, elegant method to extract the local strain in suspended and nonsuspended parts of a membrane. This opens the way to experimenting with tunable coupling between light emission and vibration.

We developed a high-yield synthesis of highly crystalline bilayer graphene (BLG) with two preferential stacking modes using a Ni-Cu gradient alloy growth substrate. Previously reported approaches for BLG growth include flat growth substrates of Cu or Ni-Cu uniform alloys and "copper pocket" structures. Use of flat substrates has the advantage of being scalable, but the growth mechanism is either "surface limited" (for Cu) or carbon precipitation (for uniform Ni-Cu), which results in multicrystalline BLG grains. For copper pockets, growth proceeds through a carbon back-diffusion mechanism, which leads to the formation of highly crystalline BLG, but scaling of the copper pocket structure is expected to be difficult. Here we demonstrate a Ni-Cu gradient alloy that combines the advantages of these earlier methods: the substrate is flat, so easy to scale, while growth proceeds by a carbon back-diffusion mechanism leading to high-yield growth of BLG with high crystallinity. The BLG layer stacking was almost exclusively Bernal or twisted with an angle of 30°, consistent with first-principles calculations we conducted. Furthermore, we demonstrated scalable production of transistor arrays based crystalline Bernal-stacked BLG with a band gap that was tunable at room temperature.

Active tunability of photonic resonances is of great interest for various applications such as optical switching and modulation based on optoelectronic materials. Manipulation of charged excitons in atomically thin transition metal dichalcogenides (TMDCs) like monolayer MoS 2 offers an unexplored route for diverse functionalities in optoelectronic nanodevices. Here, we experimentally demonstrate the dynamic photochemical and optoelectronic control of the photonic crystal Fano resonances by optical and electrical tuning of monolayer MoS 2 refractive index via trions without any chemical treatment. The strong spatial and spectral overlap between the photonic Fano mode and the active MoS 2 monolayer enables efficient modulation of the Fano resonance. Our approach offers new directions for potential applications in the development of optical modulators based on emerging 2D direct band gap semiconductors.

Atomically thin transition metal dichalcogenides like MoS 2 monolayers exhibit unique luminescent properties. However, weak quantum yield and low light absorption hinder their practical applications in two-dimensional light emitting devices. Here, we report 1300 times enhancement in photoluminescence emission from a MoS 2 monolayer via simultaneous Fano resonances in a dielectric photonic crystal. The spatially extended double Fano resonance scheme allows resonant enhancement of both the MoS 2 absorption and emission. We also achieve unidirectional emission within a narrow divergence angle of 5° by engineering the Fano resonance angular dispersion. Our approach provides a new platform for efficient light sources with high directionality based on emerging two-dimensional materials.

Heterostructures of transition metal dichalcogenides (TMDs) offer the attractive prospect of combining distinct physical properties derived from different TMD structures. Here, we report direct chemical vapor deposition of in-plane monolayer heterostructures based on 1H-MoS 2 and 1T'-MoTe 2 . The large lattice mismatch between these materials led to intriguing phenomena at their interface. Atomic force microscopy indicated buckling in the 1H region. Tip-enhanced Raman spectroscopy showed mode structure consistent with Te substitution in the 1H region during 1T'-MoTe 2 growth. This was confirmed by atomic resolution transmission electron microscopy, which also revealed an atomically stitched, dislocation-free 1H/1T' interface. Theoretical modeling revealed that both the buckling and absence of interfacial misfit dislocations were explained by lateral gradients in Te substitution levels within the 1H region and elastic coupling between 1H and 1T' domains. Phase field simulations predicted 1T' morphologies with spike-shaped islands at specific orientations consistent with experiments. Electrical measurements across the heterostructure confirmed its electrical continuity. This work demonstrates the feasibility of dislocation-free stitching of two different atomic configurations and a pathway toward direct synthesis of monolayer TMD heterostructures of different phases.

This technical report describes the development of an aptamer for sensing azole antifungal drugs during therapeutic drug monitoring. Modified synthetic evolution of ligands through exponential enrichment (SELEX) was used to discover a DNA aptamer recognizing azole class antifungal drugs. This aptamer undergoes a secondary structural change upon binding to its target molecule, as shown through fluorescence anisotropy-based binding measurements. Experiments using circular dichroism spectroscopy revealed a unique G-quadruplex structure that was essential and specific for binding to the azole antifungal target. Aptamer-functionalized graphene field effect transistor (GFET) devices were created and used to measure the strength of binding of azole antifungals to this surface. In total, this aptamer and the supporting sensing platform provide a valuable tool for therapeutic drug monitoring of patients with invasive fungal infections. IMPORTANCE We have developed the first aptamer directed toward the azole class of antifungal drugs and a functional biosensor for these drugs. This aptamer has a unique secondary structure that allows it to bind to highly hydrophobic drugs. The aptamer works as a capture component of a graphene field effect transistor device. These devices can provide a quick and easy assay for determining drug concentrations. These will be useful for therapeutic drug monitoring of azole antifungal drugs, which is necessary to deal with the complex drug dosage profiles.

The characterization of protein-nanoparticle assemblies in solution remains a challenge. We demonstrate a technique based on a graphene microelectrode for structural-functional analysis of model systems composed of nanoparticles enclosed in open-pore and closed-pore ferritin molecules. The method readily resolves the difference in accessibility of the enclosed nanoparticle for charge transfer and offers the prospect for quantitative analysis of pore-mediated transport, while shedding light on the spatial orientation of the protein subunits on the nanoparticle surface, faster and with higher sensitivity than conventional catalysis methods.

Advances in techniques for monitoring pH in complex fluids can have a significant impact on analytical and biomedical applications. This study develops flexible graphene microelectrodes (GEs) for rapid (<5 s), very-low-power (femtowatt) detection of the pH of complex biofluids by measuring real-time Faradaic charge transfer between the GE and a solution at zero electrical bias. For an idealized sample of phosphate buffer solution (PBS), the Faradaic current is varied monotonically and systematically with the pH, with a resolution of ≈0.2 pH unit. The current-pH dependence is well described by a hybrid analytical-computational model, where the electric double layer derives from an intrinsic, pH-independent (positive) charge associated with the graphene-water interface and ionizable (negative) charged groups. For ferritin solution, the relative Faradaic current, defined as the difference between the measured current response and a baseline response due to PBS, shows a strong signal associated with ferritin disassembly and the release of ferric ions at pH ≈2.0. For samples of human serum, the Faradaic current shows a reproducible rapid (<20 s) response to pH. By combining the Faradaic current and real-time current variation, the methodology is potentially suitable for use to detect tumor-induced changes in extracellular pH., (© 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Active control of light-matter interactions in semiconductors is critical for realizing next generation optoelectronic devices with real-time control of the system's optical properties and hence functionalities via external fields. The ability to dynamically manipulate optical interactions by applied fields in active materials coupled to cavities with fixed geometrical parameters opens up possibilities of controlling the lifetimes, oscillator strengths, effective mass, and relaxation properties of a coupled exciton-photon (or plasmon) system. Here, we demonstrate electrical control of exciton-plasmon coupling strengths between strong and weak coupling limits in a two-dimensional semiconductor integrated with plasmonic nanoresonators assembled in a field-effect transistor device by electrostatic doping. As a result, the energy-momentum dispersions of such an exciton-plasmon coupled system can be altered dynamically with applied electric field by modulating the excitonic properties of monolayer MoS 2 arising from many-body effects. In addition, evidence of enhanced coupling between charged excitons (trions) and plasmons was also observed upon increased carrier injection, which can be utilized for fabricating Fermionic polaritonic and magnetoplasmonic devices. The ability to dynamically control the optical properties of a coupled exciton-plasmonic system with electric fields demonstrates the versatility of the coupled system and offers a new platform for the design of optoelectronic devices with precisely tailored responses.

Monolayer materials are sensitive to their environment because all of the atoms are at their surface. We investigate how exposure to the environment affects the electrical properties of CVD-grown monolayer MoS 2 by monitoring electrical parameters of MoS 2 field-effect transistors as their environment is changed from atmosphere to high vacuum. The mobility increases and contact resistance decreases simultaneously as either the pressure is reduced or the sample is annealed in vacuum. We see a previously unobserved, non-monotonic change in threshold voltage with decreasing pressure. This result could be explained by charge transfer on the MoS 2 channel and Schottky contact formation due to adsorbates at the interface between the gold contacts and MoS 2 . Additionally, from our electrical measurements it is plausible to infer that at room temperature and pressure water and oxygen molecules adsorbed on the surface act as interface traps and scattering centers with a density of several 10 12  cm -2 eV -1 , degrading the electrical properties of monolayer MoS 2 .

Large-area growth of monolayer films of the transition metal dichalcogenides is of the utmost importance in this rapidly advancing research area. The mechanical exfoliation method offers high quality monolayer material but it is a problematic approach when applied to materials that are not air stable. One important example is 1T'-WTe 2 , which in multilayer form is reported to possess a large non saturating magnetoresistance, pressure induced superconductivity, and a weak antilocalization effect, but electrical data for the monolayer is yet to be reported due to its rapid degradation in air. Here we report a reliable and reproducible large-area growth process for obtaining many monolayer 1T'-WTe 2 flakes. We confirmed the composition and structure of monolayer 1T'-WTe 2 flakes using x-ray photoelectron spectroscopy, energy-dispersive x-ray spectroscopy, atomic force microscopy, Raman spectroscopy and aberration corrected transmission electron microscopy. We studied the time dependent degradation of monolayer 1T'-WTe 2 under ambient conditions, and we used first-principles calculations to identify reaction with oxygen as the degradation mechanism. Finally we investigated the electrical properties of monolayer 1T'-WTe 2 and found metallic conduction at low temperature along with a weak antilocalization effect that is evidence for strong spin-orbit coupling.

Liquid-based applications of biomolecule-decorated field-effect transistors (FETs) range from biosensors to in vivo implants. A critical scientific challenge is to develop a quantitative understanding of the gating effect of charged biomolecules in ionic solution and how this influences the readout of the FETs. To address this issue, we fabricated protein-decorated graphene FETs and measured their electrical properties, specifically the shift in Dirac voltage, in solutions of varying ionic strength. We found excellent quantitative agreement with a model that accounts for both the graphene polarization charge and ionic screening of ions adsorbed on the graphene as well as charged amino acids associated with the immobilized protein. The technique and analysis presented here directly couple the charging status of bound biomolecules to readout of liquid-phase FETs fabricated with graphene or other two-dimensional materials., (Copyright © 2015 Elsevier B.V. All rights reserved.)

We have developed a scalable fabrication process for the production of DNA biosensors based on gold nanoparticle-decorated graphene field effect transistors (AuNP-Gr-FETs), where monodisperse AuNPs are created through physical vapor deposition followed by thermal annealing. The FETs are created in a four-probe configuration, using an optimized bilayer photolithography process that yields chemically clean devices, as confirmed by XPS and AFM, with high carrier mobility (3590 ± 710 cm 2 /V·s) and low unintended doping (Dirac voltages of 9.4 ± 2.7 V). The AuNP-Gr-FETs were readily functionalized with thiolated probe DNA to yield DNA biosensors with a detection limit of 1 nM and high specificity against noncomplementary DNA. Our work provides a pathway toward the scalable fabrication of high-performance AuNP-Gr-FET devices for label-free nucleic acid testing in a realistic clinical setting.

Two-dimensional layered transition metal dichalcogenides (TMDCs) show great potential for optoelectronic devices due to their electronic and optical properties. A metal-semiconductor interface, as epitaxial graphene - molybdenum disulfide (MoS2), is of great interest from the standpoint of fundamental science, as it constitutes an outstanding platform to investigate the interlayer interaction in van der Waals heterostructures. Here, we study large area MoS2-graphene-heterostructures formed by direct transfer of chemical-vapor deposited MoS2 layer onto epitaxial graphene/SiC. We show that via a direct transfer, which minimizes interface contamination, we can obtain high quality and homogeneous van der Waals heterostructures. Angle-resolved photoemission spectroscopy (ARPES) measurements combined with Density Functional Theory (DFT) calculations show that the transition from indirect to direct bandgap in monolayer MoS2 is maintained in these heterostructures due to the weak van der Waals interaction with epitaxial graphene. A downshift of the Raman 2D band of the graphene, an up shift of the A1g peak of MoS2 and a significant photoluminescence quenching are observed for both monolayer and bilayer MoS2 as a result of charge transfer from MoS2 to epitaxial graphene under illumination. Our work provides a possible route to modify the thin film TDMCs photoluminescence properties via substrate engineering for future device design.