Search

Black manganese-rich crusts are found worldwide on the façades of historical buildings. In this study, they were studied exemplarily on the façade of the Freiburger Münster (Freiburg Minster), Germany, and measured in-situ by portable X-ray fluorescence (XRF). The XRF was calibrated to allow the conversion from apparent mass fractions to Mn surface density (Mn mass per area), to compensate for the fact that portable XRF mass fraction measurements from thin layers violate the assumption of a homogeneous measurement volume. Additionally, 200-nm femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs LA-ICP-MS) measurements, scanning transmission X-ray microscopy-near edge X-ray absorption fine structure spectroscopy (STXM-NEXAFS), Raman spectroscopy, and imaging by light microscopy were conducted to obtain further insight into the crust material, such as potential biogenic contributions, element distributions, trace element compositions, and organic functional groups. While black crusts of various types are present at many places on the minster's facade, crusts rich in Mn (with a Mn surface density >150 μg cm−2) are restricted to a maximum height of about 7 m. The only exceptions are those developed on the Renaissance-Vorhalle (Renaissance Portico) at a height of about 8 m. This part of the façade had been cleaned and treated with a silicon resin as recently as 2003. These crusts thus accumulated over a period of only 12 years. Yet, they are exceptionally Mn-rich with a surface density of 1200 μg cm−2, and therefore require an accumulation rate of about 100 μg cm−2 Mn per year. Trace element analyses support the theory that vehicle emissions are responsible for most of the Mn supply. Lead, barium, and zinc correlate with manganese, indicating that tire material, brake pads, and resuspended road dust are likely to be the element sources. Microscopic investigations show no organisms on or in the Mn-rich crusts. In contrast, Mn-free black crusts sampled at greater heights (>8 m) exhibited fungal and cyanobacterial encrustation. Carbon-rich spots were found by STXM-NEXAFS underneath one of the Mn-rich crusts. However, these carbon occurrences originate from soot and polycyclic aromatic hydrocarbons (PAHs) deposited on top of the crust, rather than from organisms responsible for the crust's formation, as shown by STXM-NEXAFS and Raman spectroscopic measurements. Our results suggest that the crusts develop abiogenically, with vehicle emissions as dominant element sources.

We investigated rock varnishes collected from several locations and environments worldwide by a broad range of microanalytical techniques. These techniques were selected to address the challenges posed by the chemical and structural complexity within the micrometer- to nanometer-sized structures in these geological materials. Femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs LA-ICP-MS), scanning transmission X-ray microscopy-near edge X-ray adsorption fine structure spectroscopy (STXM-NEXAFS) in combination with scanning electron microscopy (SEM) of focused ion beam (FIB) ultra-thin (100–200 nm) sections, conventional and polarization microscopy, as well as electron paramagnetic resonance (EPR) measurements were used to obtain information about these rock varnishes. Rock varnishes from different environments, which cannot readily be distinguished based on their macroscopic appearance, differ significantly in their constituent elemental mass fractions, e.g., of Mn, Fe, Ni, Co, Ba, and Pb, and their rare earth element (REE) patterns. Structural characteristics such as the particle sizes of embedded dust grains, internal structures such as layers of Mn-, Fe-, and Ca -rich material, and structures such as cavities varied between varnishes from different environments and regions in the world. The EPR spectra were consistent with aged biogenic Mn oxides in all samples, but showed subtle differences between samples of different origin. Our observations allow us to separate rock varnishes into different types, with differences that might be indicators of distinct geneses. Five different types of rock varnish could be distinguished, Type I–V, of which only Type I might be used as potential paleoclimate archive. Each varnish type has specific characteristics in terms of their elemental composition, element distribution, and structures. The combination of element ratios (Mn/Ba, Al/Ni, Mn/REY, Mn/Ce, Mn/Pb, LaN/YbN, and Ce/Ce*), total REE contents, and structures can be used to separate the different types of rock varnish from each other.

Mg/Ca is an independent proxy in paleoceanography to reconstruct past seawater temperature. Femtosecond Laser Ablation Inductively Coupled Plasma Mass Spectrometry (fs-LA-ICP-MS) was employed to determine the Mg/Ca composition of tests (shells) of the planktic foraminifer species Globigerinoides ruber albus (white chromotype) and G. ruber ruber (red/pink chromotype) sampled alive from the temperate to subtropical eastern North Atlantic with the research sailing yacht Eugen Seibold. Mg/Ca data are compared to (i) the measured in-situ temperature of ambient seawater, (ii) average mixed layer temperature, and (iii) sea surface temperature (SST). The pooled mean chamber Mg/Ca from each plankton tow site exhibits a positive relationship with SST. Two chamber-specific calibrations are derived, which are consistent with previous calibration equations for comparable paleo-archives. The results confirm fs-LA-ICP-MS as reliable method for determining Mg/Ca in G. ruber, and both the penultimate and antepenultimate chambers of adult specimens may provide comprehensible Mg/Ca temperatures of the surface ocean., (© 2024. The Author(s).)

The Baltic Sea serves as a model region to study processes leading to oxygen depletion. Reconstructing past low-oxygen occurrences, specifically hypoxia, is crucial to understand current ecological disturbances and developing future mitigation strategies. The history of dissolved oxygen (DO) concentration in some Baltic Sea basins has been investigated in previous studies, but temporally well-constrained, inter-annual and better resolved DO reconstructions are still scarce. Here, we present precisely dated, high-resolution DO record since the mid-19th century reconstructed from Mn/Ca shell values of Arctica islandica (Bivalvia) collected in the Mecklenburg Bight. According to the data, this area experienced similar low oxygenation during the second half of the 19th century and the late 20th century, but DO variability increased: A 12-15-yr oscillation prevailed in the 19th century, but a 4-6-year period dominated in the late 20th century. Shortly after the onset of the Industrial Revolution around 1850, Mn/Ca shell values increased, indicating a DO decrease, probably caused by strong anthropogenic nutrient input. More recently, phosphate levels and inflows of oxygen-rich North Sea water have been identified as major factors controlling the bottom water oxygenation. For example, the increase in DO in the mid-1990s was linked to the decrease in phosphate content and several Major Baltic Inflows. The strong Ba/Ca shell rise between the 1860s and the turn of the century most likely reflects changes in diatom community structure rather than a bloom of mass phytoplankton. This is supported by largely unchanged Mn/Ca shell and shell growth. Decadal and multi-decadal cycles of shell growth rate correlated strongly with the Atlantic Multidecadal Variability, likely reflecting changes in atmospheric circulation patterns, precipitation rate and riverine nutrient supply. To further improve the management and protection of ecosystems in the Baltic Sea, a larger number of such high-resolution retrospective studies covering long periods of time and large regions are needed., Competing Interests: Declaration of competing interest The authors have no conflicts of interest with the contents of this article., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Different approaches for the determination of the 87 Sr/ 86 Sr isotope ratio of high-Rb glass are compared in this work to assess the suitability of minimally invasive approaches for applications on medieval stained glass (from the ancient Abbey of Stavelot in Belgium). It was found that pneumatic nebulization multicollector inductively coupled plasma-mass spectrometry (PN-MC-ICP-MS) after acid digestion and chromatographic isolation of the target analyte out of the sample matrix can still be seen as the preferred method for the high-precision isotopic analysis of Sr in glass with high Rb and rare-earth element (REE) concentrations. Alternatively, the use of laser ablation (LA) for sample introduction is a powerful technique for the direct analysis of solid samples. However, both the high Rb/Sr ratios in the samples of interest and the presence of REEs at sufficiently high concentrations lead to a large bias in LA-MC-ICP-MS, which cannot be corrected for, even by operating the MC-ICP-MS instrument at higher mass resolution and/or using mathematical corrections. It was demonstrated that LA tandem-ICP-MS (LA-ICP-MS/MS) using CH 3 F/He as the reaction gas to overcome spectral overlap in a mass-shift approach (chemical resolution) provides a viable alternative when (quasi) nondestructive analysis is required. This approach relies on the monitoring of Sr + ( m/z = 86, 87, and 88) ions as the corresponding SrF + reaction product ions ( m/z = 105, 106, and 107), thus avoiding the occurrence of spectral interference. Self-evidently, the isotope ratio precision attainable using sequential quadrupole-based ICP-MS instrumentation (0.3% RSD) was found to be significantly worse than that of high-precision MC-ICP-MS (0.03% RSD) with simultaneous detection, although it was still fit for the purpose of current applications. In addition to Sr isotopic analysis, the REE patterns and their potential influence on the Sr isotopic composition were evaluated by LA-ICP-MS., Competing Interests: The authors declare no competing financial interest., (© 2021 The Authors. Published by American Chemical Society.)

We investigated rock varnish, a thin, manganese- and iron-rich, dark surface crust, on basaltic lava flows and petroglyphs in the Owens and Rose Valleys (California) by portable X-ray fluorescence (pXRF) and femtosecond laser-ablation inductively-coupled-plasma mass spectrometry (fs-LA-ICPMS). The major element composition of the varnish was consistent with a mixture of Mn-Fe oxyhydroxides and clay minerals. As expected, it contained elevated concentrations of elements that are typically enriched in rock varnish, e.g., Mn, Pb, Ba, Ce, and Co, but also showed unusually high enrichments in U, Cu, and Th. The rare earth and yttrium (REY) enrichment pattern revealed a very strong positive cerium (Ce) anomaly and distinct negative europium (Eu) and Y anomalies. The light rare earth elements (REE) were much more strongly enriched than the heavy REY. These enrichment patterns are consistent with a formation mechanism by leaching of Mn and trace elements from aeolian dust, reprecipitation of Mn and Fe as oxyhydroxides, and scavenging of trace elements by these oxyhydroxides. We inferred accumulation rates of Mn and Fe in the varnish from their areal densities measured by pXRF and the known ages of some of the lava flow surfaces. The areal densities of Mn and Fe, as well as their accumulation rates, were comparable to our previous results from the desert of Saudi Arabia. There was a moderate dependence of the Mn areal density on the inclination of the rock surfaces, but no relationship to its cardinal orientation. We attempted to use the degree of varnish regrowth on the rock art surfaces as an estimate of their age. While an absolute dating of the petroglyphs was not possible because of the lack of suitable calibration surfaces and a considerable amount of variability, the measured degree of varnish regrowth on the various petroglyphs was consistent with chronologies based on archeological and other archaeometric techniques. In particular, our results suggest that rock art creation in the study area continued over an extended period of time, possibly starting around the Pleistocene/Holocene transition and extending into the last few centuries., Competing Interests: The authors have declared that no competing interests exist.

Stable carbon and nitrogen isotope ratios of collagen from bone and dentin have frequently been used for dietary reconstruction, but this method is limited by protein preservation. Isotopes of the trace element zinc (Zn) in bioapatite constitute a promising proxy to infer dietary information from extant and extinct vertebrates. The 66 Zn/ 64 Zn ratio (expressed as δ 66 Zn value) shows an enrichment of the heavy isotope in mammals along each trophic step. However, preservation of diet-related δ 66 Zn values in fossil teeth has not been assessed yet. Here, we analyzed enamel of fossil teeth from the Late Pleistocene (38.4-13.5 ka) mammalian assemblage of the Tam Hay Marklot (THM) cave in northeastern Laos, to reconstruct the food web and assess the preservation of original δ 66 Zn values. Distinct enamel δ 66 Zn values of the fossil taxa (δ 66 Zn carnivore < δ 66 Zn omnivore < δ 66 Zn herbivore ) according to their expected feeding habits were observed, with a trophic carnivore-herbivore spacing of +0.60‰ and omnivores having intermediate values. Zn and trace element concentration profiles similar to those of modern teeth also indicate minimal impact of diagenesis on the enamel. While further work is needed to explore preservation for settings with different taphonomic conditions, the diet-related δ 66 Zn values in fossil enamel from THM cave suggest an excellent long-term preservation potential, even under tropical conditions that are well known to be adverse for collagen preservation. Zinc isotopes could thus provide a new tool to assess the diet of fossil hominins and associated fauna, as well as trophic relationships in past food webs., Competing Interests: The authors declare no competing interest., (Copyright © 2020 the Author(s). Published by PNAS.)

Here we present a new composite record from two well-dated speleothem records from two caves in Northern Morocco. The high-resolution record covers the last millennium allowing to detect multi-decadal to centennial periodicities. Over the industrial period, δ 18 O values of our speleothems are shown to be dominated by the main mode of decadal variability in the North Atlantic region: the North Atlantic Oscillation (NAO). Statistical analyses confirm the previously reported multi-decadal variability related to the influence of the Atlantic Multidecadal Oscillation (AMO) in the region. High power and persistent centennial-scale periodicities, similar to the Vries-Suess 200-year solar cycle, are observed as well. Indeed, comparison between solar activity reconstructions and our record confirms the in-phase relationship on centennial time-scales. Low δ 18 O values, and hence negative phases of NAO that bring precipitation towards the Western Mediterranean, are observed during well-known solar minima periods. The results are consistent with previous models which describe low irradiance as a  trigger for southward shifts of precipitation-bearing westerlies during winter.

Desert varnishes are dark rock coatings observed in arid environments and might resemble Mn-rich coatings found on Martian rocks. Their formation mechanism is not fully understood and the possible microbial involvement is under debate. In this study, we applied DNA metagenomic Shotgun sequencing of varnish and surrounding soil to evaluate the composition of the microbial community and its potential metabolic function. We found that the α diversity was lower in varnish compared to soil samples (p value < 0.05), suggesting distinct populations with significantly higher abundance of Actinobacteria, Proteobacteria and Cyanobacteria within the varnish. Additionally, we observed increased levels of transition metal metabolic processes in varnish compared to soil samples. Nevertheless, potentially relevant enzymes for varnish formation were detected at low to insignificant levels in both niches, indicating no current direct microbial involvement in Mn oxidation. This finding is supported by quantitative genomic analysis, elemental analysis, fluorescence imaging and scanning transmission X-ray microscopy. We thus conclude that the distinct microbial communities detected in desert varnish originate from settled Aeolian microbes, which colonized this nutrient-enriched niche, and discuss possible indirect contributions of microorganisms to the formation of desert varnish., (© 2018 Society for Applied Microbiology and John Wiley & Sons Ltd.)

The 4th century BC marks the main entrance of Celtic populations in northern Italy. Their arrival has been suggested based on the presence of Celtic customs in Etruscan mortuary contexts, yet up to now few bioarchaeological data have been examined to support or reject the arrival of these newcomers. Here we use strontium isotopes, non-metric dental traits and funerary patterns to unravel the biocultural structure of the necropolis of Monterenzio Vecchio (Bologna, Italy). Subsamples of our total sample of 38 individuals were analyzed based on different criteria characterizing the following analyses: 1) strontium isotope analysis to investigate migratory patterns and provenance; 2) non-metric dental traits to establish biological relationships between Monterenzio Vecchio, 13 Italian Iron age necropolises and three continental and non-continental Celtic necropolises; 3) grave goods which were statistically explored to detect possible patterns of cultural variability. The strontium isotopes results indicate the presence of local and non-local individuals, with some revealing patterns of mobility. The dental morphology reveals an affinity between Monterenzio Vecchio and Iron Age Italian samples. However, when the Monterenzio Vecchio sample is separated by isotopic results into locals and non-locals, the latter share affinity with the sample of non-continental Celts from Yorkshire (UK). Moreover, systematic analyses demonstrate that ethnic background does not retain measurable impact on the distribution of funerary elements. Our results confirm the migration of Celtic populations in Monterenzio as archaeologically hypothesized on the basis of the grave goods, followed by a high degree of cultural admixture between exogenous and endogenous traits. This contribution shows that combining different methods offers a more comprehensive perspective for the exploration of biocultural processes in past and present populations.

Explanations of the Classic Maya civilization demise on the Yucatán Peninsula during the Terminal Classic Period (TCP; ~CE 750-1050) are controversial. Multiyear droughts are one likely cause, but the role of the Caribbean Sea, the dominant moisture source for Mesoamerica, remains largely unknown. Here we present bimonthly-resolved snapshots of reconstructed sea surface temperature (SST) and salinity (SSS) variability in the southern Caribbean from precisely dated fossil corals. The results indicate pronounced interannual to decadal SST and SSS variability during the TCP, which may be temporally coherent to precipitation anomalies on the Yucatán. Our results are best explained by changed Caribbean SST gradients affecting the Caribbean low-level atmospheric jet with consequences for Mesoamerican precipitation, which are possibly linked to changes in Atlantic Meridional Overturning Circulation strength. Our findings provide a new perspective on the anomalous hydrological changes during the TCP that complement the oft-suggested southward displacement of the Intertropical Convergence Zone. We advocate for a strong role of Caribbean SST and SSS condition changes and related ocean-atmosphere interactions that notably influenced the propagation and transport of precipitation to the Yucatán Peninsula during the TCP.

Rationale: High spatial resolution Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LA-ICPMS) determination of trace element concentrations is of great interest for geological and environmental studies. Data reduction is a very important aspect of LA-ICP-MS, and several commercial programs for handling LA-ICPMS trace element data are available. Each of these software packages has its specific advantages and disadvantages., Methods: Here we present TERMITE, an R script for the reduction of LA-ICPMS data, which can reduce both spot and line scan measurements. Several parameters can be adjusted by the user, who does not necessarily need prior knowledge in R. Currently, ten reference materials with different matrices for calibration of LA-ICPMS data are implemented, and additional reference materials can be added by the user. TERMITE also provides an optional outlier test, and the results are provided graphically (as a pdf file) as well as numerically (as a csv file)., Results: As an example, we apply TERMITE to a speleothem sample and compare the results with those obtained using the commercial software GLITTER. The two programs give similar results. TERMITE is particularly useful for samples that are homogeneous with respect to their major element composition (in particular for the element used as an internal standard) and when many measurements are performed using the same analytical parameters. In this case, data evaluation using TERMITE is much faster than with all other available software, and the concentrations of more than 100 single spot measurements can be calculated in less than a minute., Conclusions: TERMITE is an open-source software for the reduction of LA-ICPMS data, which is particularly useful for the fast, reproducible evaluation of large datasets of samples that are homogeneous with respect to their major element composition. Copyright © 2017 John Wiley & Sons, Ltd., (Copyright © 2017 John Wiley & Sons, Ltd.)

The extent to which climate variability in Central Asia is causally linked to large-scale changes in the Asian monsoon on varying timescales remains a longstanding question. Here we present precisely dated high-resolution speleothem oxygen-carbon isotope and trace element records of Central Asia's hydroclimate variability from Tonnel'naya cave, Uzbekistan, and Kesang cave, western China. On orbital timescales, the supra-regional climate variance, inferred from our oxygen isotope records, exhibits a precessional rhythm, punctuated by millennial-scale abrupt climate events, suggesting a close coupling with the Asian monsoon. However, the local hydroclimatic variability at both cave sites, inferred from carbon isotope and trace element records, shows climate variations that are distinctly different from their supra-regional modes. Particularly, hydroclimatic changes in both Tonnel'naya and Kesang areas during the Holocene lag behind the supra-regional climate variability by several thousand years. These observations may reconcile the apparent out-of-phase hydroclimatic variability, inferred from the Holocene lake proxy records, between Westerly Central Asia and Monsoon Asia.

We present the first annually resolved record of biologically available Pb and Fe in the Greater North Sea and Iceland during 1040-2004 AD based on shells of the long-lived marine bivalve Arctica islandica. The iron content in pre-industrial shells from the North Sea largely remained below the detection limit. Only since 1830, shell Fe levels rose gradually reflecting the combined effect of increased terrestrial runoff of iron-bearing sediments and eutrophication. Although the lead gasoline peak of the 20th century was well recorded by the shells, bivalves that lived during the medieval heyday of metallurgy showed four-fold higher shell Pb levels than modern specimens. Presumably, pre-industrial bivalves were offered larger proportions of resuspended (Pb-enriched) organics, whereas modern specimens receive fresh increased amounts of (Pb-depleted) phytoplankton. As expected, metal loads in the shells from Iceland were much lower. Our study confirms that bivalve shells provide a powerful tool for retrospective environmental biomonitoring., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

The sponge siliceous spicules are formed enzymatically via silicatein, in contrast to other siliceous biominerals. Originally, silicatein had been described as a major structural protein of the spicules that has the property to allow a specific deposition of silica onto their surface. More recently, it had been unequivocally demonstrated that silicatein displays a genuine enzyme activity, initiating and maintaining silica biopolycondensation at low precursor concentrations (<2 mM). Even more, as silicatein becomes embedded into the biosilica polymer, formed by the enzyme, it retains its functionality to enable a controlled biosilica deposition. The protection of silicatein through the biosilica mantel is so strong that it conserves the functionality of the enzyme for thousands of years. The implication of this finding, the preservation of the enzyme function over such long time periods, is that the intrinsic property of silicatein to display its enzymatic activity remains in the biosilica deposits. This self-healing property of sponge biosilica can be utilized to engineer novel hybrid materials, with silicatein as a functional template, which are more resistant toward physical stress and fracture. Those hybrid materials can even be used for the fabrication of silica dielectrics coupled to optical nanowires., (Copyright © 2013 International Union of Biochemistry and Molecular Biology, Inc.)

Marine biofouling--the colonization of small marine microorganisms on surfaces that are directly exposed to seawater, such as ships' hulls--is an expensive problem that is currently without an environmentally compatible solution. Biofouling leads to increased hydrodynamic drag, which, in turn, causes increased fuel consumption and greenhouse gas emissions. Tributyltin-free antifouling coatings and paints based on metal complexes or biocides have been shown to efficiently prevent marine biofouling. However, these materials can damage the environment through metal leaching (for example, of copper and zinc) and bacteria resistance. Here, we show that vanadium pentoxide nanowires act like naturally occurring vanadium haloperoxidases to prevent marine biofouling. In the presence of bromide ions and hydrogen peroxide, the nanowires catalyse the oxidation of bromide ions to hypobromous acid (HOBr). Singlet molecular oxygen ((1)O(2)) is formed and this exerts strong antibacterial activity, which prevents marine biofouling without being toxic to marine biota. Vanadium pentoxide nanowires have the potential to be an alternative approach to conventional anti-biofouling agents.

Recycling of oceanic crust through subduction, mantle upwelling, and remelting in mantle plumes is a widely accepted mechanism to explain ocean island volcanism. The timescale of this recycling is important to our understanding of mantle circulation rates. Correlations of uranogenic lead isotopes in lavas from ocean islands such as Hawaii or Iceland, when interpreted as model isochrons, have yielded source differentiation ages between 1 and 2.5 billion years (Gyr). However, if such correlations are produced by mixing of unrelated mantle components they will have no direct age significance. Re-Os decay model ages take into account the mixing of sources with different histories, but they depend on the assumed initial Re/Os ratio of the subducted crust, which is poorly constrained because of the high mobility of rhenium during subduction. Here we report the first data on (87)Sr/(86)Sr ratios for 138 melt inclusions in olivine phenocrysts from lavas of Mauna Loa shield volcano, Hawaii, indicating enormous mantle source heterogeneity. We show that highly radiogenic strontium in severely rubidium-depleted melt inclusions matches the isotopic composition of 200-650-Myr-old sea water. We infer that such sea water must have contaminated the Mauna Loa source rock, before subduction, imparting a unique 'time stamp' on this source. Small amounts of seawater-derived strontium in plume sources may be common but can be identified clearly only in ultra-depleted melts originating from generally highly (incompatible-element) depleted source components. The presence of 200-650-Myr-old oceanic crust in the source of Hawaiian lavas implies a timescale of general mantle circulation with an average rate of about 2 (±1) cm yr(-1), much faster than previously thought.

In the present study we examined material from the Ashikule Basin of Tibet. Chemical analyses were performed by use of energy dispersive X-ray spectroscopy and electron probe microanalysis to clarify whether the varnish layers that had developed on the surface of the rhyolite are indeed composed of varnish bodies and silica glaze. Electron microscopic analyses revealed that the surface of the varnish is covered both by filamentous hyphae bacterial and cocci-shaped forms. Within the varnish mineral layer in those samples two forms of bacteria-like microorganisms exist; cocci as tightly packed bacterial aggregates [within varnish bodies], and bacillus-like microorganisms [within the varnish matrix, that surrounds the varnish bodies]. The bacillus-like forms are embedded in a network of filaments that have diameters between 35 and 45 nm. These bacilli with the surrounding filaments are assumed to have been involved in biofilm formation (synthesis of extracellular polymeric substances) prior to their live burial. We concluded that the formation of the varnish layers was for the most part biogenically driven by microorganisms., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

Background: Spicules, the siliceous skeletal elements of the siliceous sponges, are synthesized enzymatically via silicatein. The product formed, bio-silica, constitutes their inorganic matrix. It remained unexplored which reactions are involved in molding of the amorphous bio-silica and formation of a solid and rigid biomaterial., Methods: Cell and molecular biological techniques have been applied to analyze processes resulting in the hardening of the enzymatically synthesized bio-silica. The demosponge Suberites domuncula has been used for the studies., Results: Cell aggregates (primmorphs) from the sponge S. domuncula, grown in the presence of Mn-sulfate, form spicules that comprise, instead of a smooth, a rough and porous surface which is decorated with irregular bio-silica deposits. During this process, the expression of the aquaporin-8 gene becomes down-regulated. Further in vitro studies showed that aquaporin is required for dehydration, and hardening of bio-silica following its enzymatic formation. The data show that in cell aggregates grown in the presence of Mn-sulfate, aquaporin-8 is down-regulated. We conclude that in cell aggregates grown in the presence of Mn-sulfate, the removal of reaction water, produced during the bio-silica polycondensation reaction, is inhibited., General Significance: This study highlights that besides the silicatein-driven polycondensation reaction, the spicule formation also requires a phase of syneresis that results in a hardening of the material., (2011 Elsevier B.V. All rights reserved.)

The giant basal spicule of the hexactinellid sponge Monorhaphis chuni represents the longest natural siliceous structure on Earth. This spicule is composed of concentrically arranged lamellae that are approximately 10 μm thick. In the present study, we investigated the formation of outer lamellae on a cellular level using microscopic and spectroscopic techniques. It is shown that the formation of an outermost lamella begins with the association of cell clusters with the surface of the thickening and/or growing spicule. The cells release silica for controlled formation of a lamella. The pericellular (silica) material fuses to a delimited and textured layer of silica with depressions approximately 20-30 μm in diameter. The newly formed layer initially displays 40 μm wide, well-structured banded ribbons and only attains its plain surface in a final step. The chemical composition in the depressions was studied using energy dispersive X-ray spectroscopy and by staining with Texas Red. The data suggest that those depressions are the nests for the silica-forming cells and that silica formation starts with a direct association of silica-forming cells with the outer surface of the spicule, where they remain and initiate the development of the next lamellae.

Silicateins are unique enzymes of sponges (phylum Porifera) that template and catalyze the polymerization of nanoscale silicate to siliceous skeletal elements. These multifunctional spicules are often elaborately shaped, with complex symmetries. They carry an axial proteinaceous filament, consisting of silicatein and the scaffold protein silintaphin-1, which guides silica deposition and subsequent spicular morphogenesis. In vivo, the synthesis of the axial filament very likely proceeds in three steps: (a) assembly of silicatein monomers to form one pentamer; (b) assembly of pentamers to form fractal-like structures; and finally (c) assembly of fractal-like structures to form filaments. The present study was aimed at exploring the effect of self-assembled complexes of silicatein and silintaphin-1 on biosilica synthesis in vitro. Hence, in a comparative approach, recombinant silicatein and recombinant silintaphin-1 were used at different stoichiometric ratios to form axial filaments and to synthesize biosilica. Whereas recombinant silicatein-α reaggregates to randomly organized structures, coincubation of silicatein-α and silintaphin-1 (molecular ratio 4 : 1) resulted in synthetic filaments via fractal-like patterned self-assemblies, as observed by electron microscopy. Concurrently, owing to the concerted action of both proteins, the enzymatic activity of silicatein-α strongly increased by 5.3-fold (with the substrate tetraethyl orthosilicate), leading to significantly enhanced synthesis of biosilica. These results indicate that silicatein-α-mediated biosilicification depends on the concomitant presence of silicatein-α and silintaphin-1. Accordingly, silintaphin-1 might not only enhance the enzymatic activity of silicatein-α, but also accelerate the nonenzymatic polycondensation of the silica product before releasing the fully synthesized biosiliceous polymer., (© 2011 The Authors Journal compilation © 2011 FEBS.)

The enzymatic-silicatein mediated formation of the skeletal elements, the spicules of siliceous sponges starts intracellularly and is completed extracellularly. With Suberites domuncula we show that the axial growth of the spicules proceeds in three phases: (I) formation of an axial canal; (II) evagination of a cell process into the axial canal, and (III) assembly of the axial filament composed of silicatein. During these phases the core part of the spicule is synthesized. Silicatein and its substrate silicate are stored in silicasomes, found both inside and outside of the cellular extension within the axial canal, as well as all around the spicule. The membranes of the silicasomes are interspersed by pores of ≈ 2 nm that are likely associated with aquaporin channels which are implicated in the hardening of the initial bio-silica products formed by silicatein. We can summarize the sequence of events that govern spicule formation as follows: differential GENETIC READOUT (of silicatein) → FRACTAL ASSOCIATION of the silicateins → EVAGINATION of cells by hydro-mechanical forces into the axial canal → and finally PROCESSIVE BIO-SILICA POLYCONDENSATION around the axial canal. We termed this process, occurring sequentially or in parallel, BIO-INORGANIC SELF-ORGANIZATION.

The depth of the ocean is plentifully populated with a highly diverse fauna and flora, from where the Challenger expedition (1873-1876) treasured up a rich collection of vitreous sponges [Hexactinellida]. They have been described by Schulze and represent the phylogenetically oldest class of siliceous sponges [phylum Porifera]; they are eye-catching because of their distinct body plan, which relies on a filigree skeleton. It is constructed by an array of morphologically determined elements, the spicules. Later, during the German Deep Sea Expedition "Valdivia" (1898-1899), Schulze could describe the largest siliceous hexactinellid sponge on Earth, the up to 3 m high Monorhaphis chuni, which develops the equally largest bio-silica structures, the giant basal spicules (3 m × 10 mm). With such spicules as a model, basic knowledge on the morphology, formation, and development of the skeletal elements could be elaborated. Spicules are formed by a proteinaceous scaffold which mediates the formation of siliceous lamellae in which the proteins are encased. Up to eight hundred 5 to 10 μm thick lamellae can be concentrically arranged around an axial canal. The silica matrix is composed of almost pure silicon and oxygen, providing it with unusual optophysical properties that are superior to those of man-made waveguides. Experiments indicated that the spicules function in vivo as a nonocular photoreception system. In addition, the spicules have exceptional mechanical properties, combining mechanical stability with strength and stiffness. Like demosponges the hexactinellids synthesize their silica enzymatically, via the enzyme silicatein. All these basic insights will surely contribute also to a further applied utilization and exploration of bio-silica in material/medical science.

The skeleton of siliceous sponges (phylum Porifera: classes Demospongiae and Hexactinellida), composed of tightly interacting spicules that assemble to a genetically fixed scaffold, is formed of bio-silica. This inorganic framework with the quality of quartz glass has been shown to operate as light waveguide in vitro and very likely has a similar function in vivo. Furthermore, the molecular toolkit for endogenous light generation (luciferase) and light/photon harvesting (cryptochrome) has been identified in the demosponge Suberites domuncula. These three components of a light signaling system, spicules-luciferase-cryptochrome, are concentrated in the surface layers (cortex) of the poriferan body. Specimens from which this cortex has been removed/ablated do not emit light. However, with regeneration and reconstitution of the cortex the animals re-gain the capacity to flash light. This newly discovered characteristic of sponges to generate light prompted us to investigate the genetic basis for the endogenous light signaling system. As a potential transcription factor involved in the expression of luciferase and cryptochrome, a SOX-related protein has been identified. In dark-adapted animals or in tissue from below the cortex region, the medulla, no gene or protein expression of SOX-related protein, luciferase, and cryptochrome could be detected. However, during the regeneration of the cortex, a stage-specific expression pattern was recorded: SOX-related protein > luciferase > cryptochrome. We conclude that a flashing light signaling circuit exists, which might control the retinoic acid-induced differentiation of stem cells into pulsating and contracting sponge cells, that is, pinacocytes and myocytes., (Copyright © 2010 Wiley-Liss, Inc.)

The giant basal spicules (GBS) from Monorhaphis chuni (Porifera [sponges], Hexactinellida) represent the largest biosilica structures on Earth and can reach lengths of 300 cm (diameter of 1.1 cm). The amorphous silica of the inorganic matrix is formed enzymatically by silicatein. During this process, the enzyme remains trapped inside the lamellar-organized spicules. In order to localize the organic silicatein scaffold, the inside of a lamella has been analyzed by nano-secondary ion mass spectrometry (NanoSIMS). It is shown that the GBSs are composed of around 245 concentrically arranged individual siliceous lamellae. These surround an internal siliceous axial cylinder. The lamellae adjacent to the cylinder are thicker (10-30 mum) than the more peripheral lamellae (2-10 microm). One lamella of a thickness of 18 mum has been selected for further analysis. This lamella itself is composed of three sublamellae with an individual thickness of 2-6 microm each, which are then further organized into three cylindrical slats (thickness: 1.6-1.8 microm). Other than the main lamellae, the sublamellae are not separated from each other by gaps. The element analysis of the sublamellae by NanoSIMS revealed that the siliceous matrix is embedded in an organic matrix that consists of up to 6-10 wt/% of C. The pattern of C distribution reflects a distinct zonation of the organic material within the solid intralamellar biosiliceous material. A growth model for the lamella starting from nanosized silica particles is proposed: During formation of a lamella nanosized silica particles fuse, through biosintering processes, to slats that build the individual sublamellae, which then finally form the lamellae. In turn, those lamellae may form the higher structural entity, the axial cylinder.

Based on the light-reactive behavior of siliceous sponges, their intriguing quartz glass-based spicular system and the existence of a light-generating luciferase [Müller WEG et al. (2009) Cell Mol Life Sci 66, 537-552], a protein potentially involved in light reception has been identified, cloned and recombinantly expressed from the demosponge Suberites domuncula. Its sequence displays two domains characteristic of cryptochrome, the N-terminal photolyase-related region and the C-terminal FAD-binding domain. The expression level of S. domuncula cryptochrome depends on animal's exposure to light and is highest in tissue regions rich in siliceous spicules; in the dark, no cryptochrome transcripts/translational products are seen. From the experimental data, it is proposed that sponges might employ a luciferase-like protein, the spicular system and a cryptochrome as the light source, optical waveguide and photosensor, respectively.

While most forms of multicellular life have developed a calcium-based skeleton, a few specialized organisms complement their body plan with silica. However, of all recent animals, only sponges (phylum Porifera) are able to polymerize silica enzymatically mediated in order to generate massive siliceous skeletal elements (spicules) during a unique reaction, at ambient temperature and pressure. During this biomineralization process (i.e., biosilicification) hydrated, amorphous silica is deposited within highly specialized sponge cells, ultimately resulting in structures that range in size from micrometers to meters. Spicules lend structural stability to the sponge body, deter predators, and transmit light similar to optic fibers. This peculiar phenomenon has been comprehensively studied in recent years and in several approaches, the molecular background was explored to create tools that might be employed for novel bioinspired biotechnological and biomedical applications. Thus, it was discovered that spiculogenesis is mediated by the enzyme silicatein and starts intracellularly. The resulting silica nanoparticles fuse and subsequently form concentric lamellar layers around a central protein filament, consisting of silicatein and the scaffold protein silintaphin-1. Once the growing spicule is extruded into the extracellular space, it obtains final size and shape. Again, this process is mediated by silicatein and silintaphin-1, in combination with other molecules such as galectin and collagen. The molecular toolbox generated so far allows the fabrication of novel micro- and nanostructured composites, contributing to the economical and sustainable synthesis of biomaterials with unique characteristics. In this context, first bioinspired approaches implement recombinant silicatein and silintaphin-1 for applications in the field of biomedicine (biosilica-mediated regeneration of tooth and bone defects) or micro-optics (in vitro synthesis of light waveguides) with promising results.

In this study we have validated a newly developed multi-element isotope dilution (ID) ICPMS method for the simultaneous analysis of up to 12 trace elements in geological samples. By evaluating the analytical uncertainty of individual components using certified reference materials we have quantified the overall analytical uncertainty of the multi-element ID ICPMS method at 1-2%. Individual components include sampling/weighing, purity of reagents, purity of spike solutions, calibration of spikes, determination of isotopic ratios, instrumental sources of error, correction of mass discrimination effect, values of constants, and operator bias. We have used the ID-determined trace elements for internal standardization to improve indirectly the analysis of 14 other (mainly mono-isotopic trace elements) by external calibration. The overall analytical uncertainty for those data is about 2-3%. In addition, we have analyzed USGS and MPI-DING geological reference materials (BHVO-1, BHVO-2, KL2-G, ML3B-G) to quantify the overall bias of the measurement procedure. Trace element analysis of geological reference materials yielded results that agree mostly within about 2-3% relative to the reference values. Since these results match the conclusions obtained by the investigation of the overall analytical uncertainty, we take this as a measure for the validity of multi-element ID ICPMS.

Spark source mass spectrometry (SSMS) has experienced important and significant improvements in nearly all analytical features by the use of a multiple ion counting (MIC) system. Two procedures have recently been developed to further increase the analytical capabilities of MIC-SSMS in geochemistry. These are a mathematical correction of interferences, which is often necessary for the ultra trace element analysis of Nb, Ta, Zr, Hf and Y, and the development of an autospark system to hold the total ion beam constant. New analytical data for geological samples, especially international reference materials, are presented using the improved MIC-SSMS technique. The data set consists of high precision and low abundance data for Zr, Nb and Y in depleted reference materials. The MIC-SSMS results are compared with those of conventional SSMS using photoplates for ion detection. The precision of the MIC-SSMS isotope ratio measurements (about 1%) is more than a factor of 3 better than that of conventional SSMS, as demonstrated by analyses of Hawaiian samples. Total uncertainties of MIC-SSMS concentration data including all sources of error are generally between 2 and 5% for concentrations higher than about 0.3 microg/g and about 10% for trace element abundances in the ng/g range.