Search

In this study, the mechanical properties of aluminum vibration damping sheet and 1.5 GPa HPF steel sheet (SABC1470) dissimilar joining were evaluated. Joint methods of self piercing rivet (SPR), bolt/nut, flow drill screw (FDS), and blind rivet were compared to evaluate joint characteristic. In SPR Joining, buckling failure was occurred in SPR rivet caused by the strength of the 1.5 GPa HPF steel. So that, SPR hybrid joining was selected with a Al5052 alloy additional plate in lower sheet for formability and pre-hole processed on 1.5 GPa HPF steel in upper sheet. Through optimized of SPR die, the tensile shear load of the SPR hybrid joining was measured 7.53 kN. In FDS joining, failure of fastener was occurred due to the high strength of the 1.5 GPa HPF steel. FDS joining was available after pre-hole process on the 1.5 GPa HPF steel. However, delamination of the aluminum damping plate was observed and the tensile shear load was measured 3.14 kN. In bolt/nut joining, tensile shear load was measured depending on process variable (combination of plate, washer and tightening torque) and maximum tensile load was measured 5.43 kN. In blind rivet joining, the maximum tensile shear load was measured 3.64 kN, when the Al vibration damping sheet was placed on the upper plate. The large area of the blind rivet head released the concentration of stress on Al vibration damping sheet. As a result, SPR hybrid joining is considerable method because pre-hole processing is minimized and tensile shear load is higher than the other method.

The necessity of dissimilar joining between aluminum alloy and steel is increasing in order to meet the demand for weight reduction in automobiles. However, dissimilar joining between 7000 series aluminum alloy and steel is challenging with mechanical joining methods such as self-piercing rivet(SPR) and flow drill screw(FDS) without hole processing. In this study, mechanical performances of dissimilar joints between 3 mm thick Al7075-T6 and 1 mm thick SPFC590DP were evaluated for use in lightweight B-pillar assembly. Self-Piercing Rivet(SPR) and Flow Drill Screw(FDS) with one-hole processing, bolt/nut and blind rivet with two-hole processing and adhesive bonding were compared with respect to joint performance. In SPR joining, rivet did not penetrate and rivet buckling occurred in the rivet due to the thickness and high strength of the Al7075-T6. By processing pre-hole on Al7075-T6 and applying an additional Al5052-H32 sheet to induce mechanical interlock in SPR joint, it became possible to join Al7075-T6 to SPFC590DP with an SPR. The tensile shear load of the SPR joint was 9.8 kN. In FDS joining, it is also necessary to process pre-hole on Al7075-T6 since the fastener could not penetrate the Al7075-T6. The tensile shear load of the FDS joining was 8.1 kN. In bolt/nut and blind rivet joining, the tensile shear load were measured respectively 11.1 kN and 5.2 kN. In adhesive bonding with 1K glue, the tensile shear load was measured 18.5 kN when the interfacial surface was roughened with a sand paper.

An electrospun nanofiber membrane significantly improves the electrical performances of triboelectric nanogenerators (TENGs) due to its high surface area. In recent years, composite nanofibers were applied to a TENG using various electrospinning system types to further enhance the performance of TENGs; however, the effects of the systems on the energy harvesting capability of TENGs have not been investigated thoroughly. This study aims to fabricate polyimide/poly(vinylidene fluoride-co-trifluoroethylene) composite nanofiber-based TENGs with three different nozzle systems: single nozzle, conjugated nozzle, and multinozzles, and two different collectors: plate collector and drum collector. A TENG with multinozzle-drum system-based nanofibers produced an output voltage of 364 V, a short-circuit current of 17.2 μA, a transferred charge of 29.72 nC, and a power density of 2.56 W/m2 at a load resistance of 100 MΩ, which were ∼7 times higher than those of other system-based nanofibers. Under the 10,000 cycles of loading, the TENG stably harvested electric energy. The TENG could also harvest energy from the human body motions, and it is sufficient to illuminate 117 light-emitting diodes and drive several electronic devices. The proposed TENG exhibits excellent electric performances as a wearable energy harvester.

BackgroundCerebral aneurysms should be treated before rupture because ruptured aneurysms result in serious disability. Therefore, accurate prediction of rupture risk is important and has been estimated using various hemodynamic factors.ObjectiveTo suggest a new way to predict rupture risk in cerebral aneurysms using a novel deep learning model based on hemodynamic parameters for better decision-making about treatment.MethodsA novel convolutional neural network (CNN) model was used for rupture risk prediction retrospectively of 123 aneurysm cases. To include the effect of hemodynamic parameters into the CNN, the hemodynamic parameters were first calculated using computational fluid dynamics and fluid–structure interaction. Then, they were converted into images for training the CNN using a novel approach. In addition, new data augmentation methods were devised to obtain sufficient training data. A total of 53,136 images generated by data augmentation were used to train and test the CNN.ResultsThe CNNs trained with wall shear stress (WSS), strain, and combination images had area under the receiver operating characteristics curve values of 0.716, 0.741, and 0.883, respectively. Based on the cut-off values, the CNN trained with WSS (sensitivity: 0.5, specificity: 0.79) or strain (sensitivity: 0.74, specificity: 0.71) images alone was not highly predictive. However, the CNN trained with combination images of WSS and strain showed a sensitivity and specificity of 0.81 and 0.82, respectively.ConclusionCNN-based deep learning algorithm using hemodynamic factors, including WSS and strain, could be an effective tool for predicting rupture risk in cerebral aneurysms with good predictive accuracy.

Arc instability is one of the most critical problems in gas-metal-arc (GMA) based wire arc additive manufacturing of titanium (Ti) alloys. It can result in a poor bead surface, surface oxidation, and spattering. In particular, the relocation of the cathode spot area is the main cause of big spatters because of the high thermal energy of the molten droplet at the molten pool surface. In this study, two cathode spot control techniques were applied using auxiliary laser heating and prelaid oxides, and the behaviors of the cathode spots and arc were visualized using high-speed photography. When the laser beam was irradiated in front of the GMA, a cathode spot was formed at the laser irradiation position, and the cathode jet did not interfere with the arc plasma and droplet transfer from the GMA. However, when the distance between the GMA and the laser irradiation position increased by more than 8 mm, multiple cathode spots were established, and spattering increased. The prelaid Ti oxide particles increased the metal deposition efficiency by establishing multiple and dispersed cathode spots rather than a concentrated cathode spot by droplet impingement. It was found that the volumetric transfer efficiencies (excluding spattering) for the laser-assisted control and Ti oxide powder were up to 99.87% and 91.2%, respectively.

Purpose: The flow diversion effect of an intracranial stent is closely related to its metal coverage rate (MCR). In this study, the flow diversion effects of Enterprise and low-profile visualized intraluminal support (LVIS) stents are compared with those of a Pipeline flow diverter, focusing on the MCR change. Moreover, the changes in the flow diversion effect caused by the additional manipulations of overlapping and compaction are verified using computational fluid dynamics (CFD) analysis.Methods: CFD analysis was performed using virtually generated stents mounted in an idealized aneurysm model. First, the flow diversion effects of single Enterprise, LVIS, and Pipeline devices were analyzed. The Enterprise and LVIS were sequentially overlapped and compared with a Pipeline, to evaluate the effect of stent overlapping. The effect of compacting a stent was evaluated by comparing the flow diversion effects of a single and two compacted LVIS with those of two overlapped, uncompacted LVIS and uncompacted and compacted Pipeline. Quantitative analysis was performed to evaluate the hemodynamic parameters of energy loss, average velocity, and inflow rate.Results: Statistically significant correlations were observed between the reduction rates of the hemodynamic parameters and MCR. The single LVIS without compaction induced a reduction in all the hemodynamic parameters comparable to those of the three overlapped Enterprise. Moreover, the two overlapped, uncompacted LVIS showed a flow diversion effect as large as that induced by the single uncompacted Pipeline. Compacted stents induced a better flow diversion effect than uncompacted stents. The single compacted LVIS induced a flow diversion effect similar to that induced by the two uncompacted LVIS or single uncompacted Pipeline.Conclusions: The MCR of a stent correlates with its flow diversion effect. Overlapping and compaction can increase the MCR of an intracranial stent and achieve a flow diversion effect as large as that observed with a flow diverter.

An optimum design methodology for a large area, flexure-based XYθ mask alignment stage, which can be applied to a 12-inch wafer photolithography process, was presented. The XYθ micropositioning stage consisted of a working plate with a 12-inch hole in the center, three piezo actuators, and three displacement amplifiers based on the bridge-type flexure mechanism. Grey relation analysis and orthogonal array were incorporated with finite element analysis to find optimum design conditions. The grey relation grade with weight factors was used to simultaneously optimize three objective characteristics of the micropositioning stage: the maximum stroke, deflection of the working plate, and first natural frequency. The optimally-designed stage was fabricated by wire electrical discharge machining and tested to investigate its performance. The proposed stage showed the first natural frequency of 57 Hz and the maximum stroke of 122.84 μm, 108.46 μm, 0.685 mrad in the x-, y-, and θ-direction, respectively. The resolutions in corresponding directions were 11 nm, 10 nm, and 0.5 μrad. The performance of the stage was improved by optimum design process, and the experimental results were in good agreement with the predicted ones from the finite element analysis.

In this study, the effects of various fabrication parameters on the electrical performance of an electrospun nanofiber-based triboelectric nanogenerator (EN-TENG) are systematically investigated through the design of experiments. We selected four fabrication parameters to examine, namely: (i) working distance (needle to collector distance), (ii) needle gauge, (iii) electrospinning time, and (iv) counter materials. A mixed orthogonal array of L18 experiments was designed with respect to the one factor having two level values and three factors having three level values. The open circuit voltage of the EN-TENG was varied from 86.1 to 576.7 V with the aforementioned fabrication parameters. A longer working distance, a larger needle gauge, and a longer electrospinning time increased the open circuit voltage. The power density of the optimized EN-TENG was approximately 2.39 W/m2 at a 100 MΩ load resistance and was sufficient to illuminate a total of 200 LEDs.

This study aims to improve the sensitivity of sensors using porous structures and cone-shaped patterns in the composition of a capacitive pressure sensor. A simple and rapid fabrication method for the production of porous structures and cone-shaped patterns using microwave irradiation of emulsions containing polydimethylsiloxane (PDMS) and a sacrificial solvent is introduced in this study. Through this method, a porous PDMS dielectric layer could be simply fabricated within a few minutes. The sensitivity was greatly improved by both enhancing deformability and increasing the dielectric constant under the external pressure. The effect of pattern distance was investigated, and the sensor with the pattern distance of 600 μm showed a remarkably high sensitivity of approximately 5 kPa−1. Moreover, the effect of aspect ratio and sharpness of the patterns were also studied through a finite element analysis. Finally, we demonstrated the performance of the sensor using a sensor array and finger attached sensors, and they showed sufficient performance for use in wearable devices applicable to artificial skin, surgical robots, and pressure monitoring systems, among others.

In recent years, innovative research has been widely conducted on flexible devices for wearable electronics applications. Many examples of wearable electronics, such as smartwatches and glasses, are already available to consumers. However, strictly speaking, the sensors used in these devices are not flexible. Many studies are underway to address a wider range of wearable electronics and the development of related fields is progressing very rapidly. In particular, there is intense interest in the research field of flexible pressure sensors because they can collect and use information regarding a wide variety of sources. Through the combination of novel materials and fabrication methods, human-machine interfaces, biomedical sensors, and motion detection techniques, it is now possible to produce sensors with a superior level of performance to meet the demands of wearable electronics. In addition, more compact and human-friendly sensors have been invented in recent years, as biodegradable and self-powered sensor systems have been studied. In this review, a comprehensive description of flexible pressure sensors will be covered, and design strategies that meet the needs for applications in wearable electronics will be presented. Moreover, we will cover several fabrication methods to implement these technologies and the corresponding real-world applications.

Surface modification of polyimides (PIs) using electrospinning would significantly improve the performance of TENGs because of the larger surface area of the electrospun friction layer. However, PIs generally have high solvent resistance, so it is complicated to convert them into nanofibers using electrospinning process. This study aims to fabricate PI nanofibers via simple, one-step electrospinning and utilize them as a friction layer of TENGs for better performance. PI nanofibers were directly electrospun from PI ink made of polyimide powder without any additional process. The effect of PI concentration on spinnability was investigated. Uniform and continuous nanofibrous structures were successfully produced at concentrations of 15 wt% and 20 wt%. Electrospun PI nanofibers were then utilized as a friction layer for TENGs. A TENG with 20 wt% produced an open circuit voltage of 753 V and a short circuit current of 10.79 μA and showed a power density of 2.61 W m−2 at a 100 MΩ load resistance. During tapping experiment of 10,000 cycles, the TENG could stably harvest electrical energy. The harvested energy from the proposed TENG is sufficient to illuminate more than 55 LEDs and drive small electronic devices, and the TENGs exhibit excellent performance as a wearable energy harvester.

Bolts tend to show different fatigue behavior with respect to the size or shape of a bolt and the level of preload though it is the same material. This makes it difficult to predict the fatigue life of bolts. In this study, a novel method to construct a unified stress-life (S-N) curve was proposed for the three different bolts with different sizes and lengths subjected to various external axial loading conditions and preloads, ranging from 44 % to 88% of the ultimate tensile stress. A total of 133 experiments for 46 different fatigue conditions were conducted and finite element analysis was also performed to calculate multiaxial stress components at the root of the thread. The fatigue characteristics of the bolts were investigated depending on various loading conditions, and the life prediction performance with fitted S-N curves was compared with respect to four mean stress correction models. The unified S-N curve showed high accuracy in life prediction; 15 % mean absolute error without exceeding ± 50 % for finite life loading conditions.

Object. Rupture of a cerebral aneurysm occurs mainly in a thin-walled area (TWA). Prediction of TWAs would help to assess the risk of rupture and select appropriate treatment strategy. There are several limitations of current prediction techniques for TWAs. To predict TWAs more accurately, HP should be normalized to minimize the influence of analysis conditions, and the effectiveness of normalized, combined hemodynamic parameters (CHPs) should be investigated with help of the quantitative color analysis of intraoperative images. Methods. A total of 21 unruptured cerebral aneurysms in 19 patients were analyzed. A normalized CHP was newly suggested as a weighted average of normalized wall shear stress (WSS) and normalized oscillatory shear index (OSI). Delta E from International Commission on Illumination was used to more objectively quantify color differences in intraoperative images. Results. CFD analysis results indicated that WSS and OSI were more predictive of TWAs than pressure (P P=.187, P=.970, respectively); these two parameters were selected to define the normalized CHP. The normalized CHP became more statistically significant (PP Conclusion. 100% weighting on the normalized WSS produced the most statistically significant result. The normalization scheme for WSS and OSI suggested in this work was validated using quantitative color analyses, rather than subjective judgments, of intraoperative images, and it might be clinically useful for predicting TWAs of unruptured cerebral aneurysms. The normalization scheme would also be integrated into further fluid-structure interaction analysis for more reliable estimation of the risk of aneurysm rupture.

The objective of this work is to establish a volumetric metal 3-dimensional (3D) printing system based on material extrusion method and to fabricate metal patterns by investigating various process variables. Numerical heat transfer simulation was conducted to design the nozzle system with a minimized heat loss at the nozzle tip. Based on the simulation results, a metal 3D printing system with X, Y, and Z stages was constructed. The effects of lead content in molten metals and printing conditions such as stage speed and flow rate were investigated. The line formation like bulged, uniform, and dashed lines was evaluated using an optical microscope, and the variation in line widths of uniform lines was investigated with the process variables. Various types of 2-dimensional (2D) patterns were fabricated with an optimized process variable. A simple 3D structure was obtained to demonstrate the feasibility of the proposed system and procedure.

The fatigue life of the resistance spot weld of 980 MPa grade transformation induced plasticity (TRIP) steel was investigated and failure modes and fracture surfaces according to the fatigue load were analyzed. The fatigue life according to the nugget size was observed by using two electrodes with face diameters of 8 mm and 10 mm. When an electrode face diameter with 10 mm was used, the nugget size was large, and the fatigue life was further increased. After the fatigue test, three types of failure modes were observed, namely pull-out, plug, and heat affected zone (HAZ) failure, depending on the fatigue load. The fracture surfaces in each failure mode were analyzed. In all failure modes, a crack was initiated in the HAZ region, which is the interface between the two materials in all failure modes. In the case of pull-out failure, the crack propagates as if it surrounds the nugget at the outer edge of the nugget. In the case of HAZ failure, the crack propagates in the thickness direction of the material and outward in the nugget shell. Plug failure occurs with pull-out failure and HAZ failure mixed. The propagation patterns of cracks were different for each failure mode. The reason why the failure mode and the fracture surface are different according to the fatigue load is that the propagation speed of the fatigue crack is fast when the fatigue load is relatively large and is slow when the fatigue load is low.

The aim of this study is to design and test a new, simple, and reusable linear variable differential transformer (LVDT)-based in situ bolt preload monitoring system (L-PMS) during fastening of a truck wheel assembly. Instead of measuring the elongation of a bolt, the distance between the end surfaces of both the bolt and nut was monitored via the L-PMS. The distance obtained from the L-PMS was experimentally correlated with the actual preload measured by a washer-type load cell. Since the variation of the distance is related to the stiffness of the bolt and clamped parts, a finite element analysis was also conducted to predict the sensitivity of L-PMS. There was a strong linear relationship between the distance and bolt preload after the bolt and nut were fully snugged. However, a logarithm-shaped nonlinear relationship was irregularly observed before getting snugged, making it difficult to define a clear relationship. In order to tackle this issue, an arc-shaped conductive line was screen-printed onto the surface of the clamped parts using a conductive carbon paste. The results show that a resistance variation of the conductive line during fastening enables to determine the snug point, so the L-PMS combined with resistance measurement results in an approximately &plusmn, 6% error in the measurement of bolt preload. The proposed L-PMS offers a simple but highly reliable way for measuring bolt preload during fastening, which could be utilized in a heavy-truck production line.

Pressure sensors for wearable electronics are mounted on irregular surfaces and exposed to various external stimuli. Therefore, the sensor should have a flexible structure and wide pressure measurement range along with high sensitivity. In this study, we fabricated hierarchically porous structured polydimethylsiloxane (PDMS) composites with a simple and cost-effective method using sugar particles and a water-in-oil emulsion. Hierarchically porous PDMS composites were employed as the dielectric layers of flexible capacitive pressure sensors. The capacitive pressure sensor presents a sensitivity 22.5 times higher (0.18 kPa−1) than the sensors using bulk PDMS with a wide measurement range (0–400 kPa). The finite element analysis was implemented to analyze the non-linearity of sensors by observing the compressive behavior of the PDMS composites. For the practical applications, finger attached-sensor, respiration monitoring system, and sensor array were tested, and the proposed sensors showed sufficient potential for application in wearable electronics.

In this study, we develop a simple and low-cost surface wettability patterning based on soft lithography processes such as nano-imprint lithography (NIL) and micro-contact printing (μCP) to fabricate high-resolution conductive patterns using two different solution processes: inkjet printing and spin coating. An epoxy-based photoresist layer was imprinted by an elastomeric stamp during the NIL process to produce negative micro-structures in the epoxy-based photoresist layer. To form surface wettability contrast, a hydrophobic fluorocarbon film was transferred onto the top surface of the imprinted epoxy-based photoresist layer using μCP. The epoxy-based photoresist layer was UV-treated before the μCP process in order to increase surface wettability contrast; the hydrophilic imprinted patterns surrounded by hydrophobic surfaces were fabricated in the epoxy-based photoresist layer. After printing Ag ink on the imprinted epoxy-based photoresist layer, high-resolution printed line array and square spiral patterns with line width and gap distance of several micrometers can be fabricated with an aid of high surface wettability contrast. Even though well-defined high-resolution conductive patterns with electrical resistivity lower than 6 μΩ cm can be obtained regardless of the solution processes, inkjet printing seems more efficient from the viewpoint of the amount of ink used in each solution process. The surface wettability patterning suggested in this study is expected to be used in the fabrication of high-resolution conductive patterns in printed electronics.

In this study, we investigate the evaporation behavior of inkjet-printed semiconductor layers of 6,13-bis(triisopropylsilylethynyl) pentacene (TIPS pentacene) to obtain well-oriented crystalline structures for the fabrication of high-performance organic thin film transistors (OTFTs). Variations in overlap and substrate temperature are considered to control the evaporation behavior and the resulting crystalline structures of the layers. The internal flow and corresponding contact line movement can be controlled via three representative inkjet-printing regimes. For inkjet-printing regimes that induce outward convective flow (the coffee stain effect), randomly-oriented TIPS pentacene crystalline structures are produced by irregular contact line receding. With an optimized inkjet-printing regime, uniform bottom contact line movement is generated by the unidirectional internal flow, resulting in well-oriented crystalline structures. All-inkjet-printed OTFTs with semiconductor layers inkjet-printed using the optimized regime exhibit a high field effect mobility of ~ 0.13 cm 2 /Vs, due to the one-dimensionally-oriented TIPS pentacene crystal arrays.

Proximity exposure with line beam scanning can be an alternative to traditional proximity exposure for a fast, high-resolution, large-area patterning. The optical elements used for shaping the line beams have a very large length-to-cross-sectional area ratio, so even small misalignment has a large effect on the optical path. In this study, a lens mount system based on kinematic coupling was established to accurately locate and align the line beam lens. Finite element models of the line beam lens and the mount were constructed, and then static structural simulations were performed. Optical paths concerning lens deformation and misalignment were calculated based on the vector equations for lines, surfaces, and Snell's law. An optimum design process based on the Taguchi method was carried out to minimize the difference between the actual optical arrival location and the target location. The stiffness and clamping force of the clamp part and support positions were selected as design variables, and the geometrical uncertainties of the lens supports was treated as error factors. A cross product array was constructed for each design variable and error factor, and then a total of 36 simulations were performed. Finally, the influence of each design variable on the optical path was analyzed, and the optimum conditions for the design variables, minimizing the error factor, were determined. As a result, the optical path error due to the geometrical uncertainty was reduced by approximately 30% compared to initial design.

Even though porous elastomers and elastomeric nanocomposites have shown many advantages for triboelectric nanogenerators (TENGs), their fabrication techniques are relatively complicated, inefficient, and time-consuming. In this work, we introduced a simple, efficient and rapid concept to fabricate porous polydimethylsiloxane (PDMS) nanocomposites. PDMS nanocomposites with various porous structure were produced within a few minutes through just one-step microwave irradiation without any post-processing. Three solvents with different boiling points were selected as sacrificial materials to control porous structure. To fabricate nanocomposites, BaTiO3 (BT) nanoparticles were mixed into the uncured PDMS and sacrificial solvent mixture. Additionally, Ni nanoparticles were also used to understand the effect of embedded material’s property on porous structure. The porous BT/PDMS nanocomposites fabricated via microwave irradiation greatly enhanced the electrical performance of TENGs as compared to a pure solid elastomer. The present study provides a simple, rapid and inexpensive approach for fabricating TENGs based on porous elastomeric nanocomposites.

Even though porous elastomers and elastomeric nanocomposites have shown many advantages for triboelectric nanogenerators (TENGs), their fabrication techniques are relatively complicated, inefficient, and time-consuming. In this work, we introduced a simple, efficient and rapid concept to fabricate porous polydimethylsiloxane (PDMS) nanocomposites. PDMS nanocomposites with various porous structure were produced within a few minutes through just one-step microwave irradiation without any post-processing. Three solvents with different boiling points were selected as sacrificial materials to control porous structure. To fabricate nanocomposites, BaTiO

In this study, we investigated geometrical characteristics of the inkjet-printed lines with non-zero receding contact angle (CA) on plasma-treated substrates in terms of various printing variables and analyzed the fluidic behavior and hydrodynamic instability involved in the line formation process. The printing variables included surface energy, droplet overlap ratio, printing frequency, a number of ink droplets, substrate temperature and printing procedures. For the study, a colloidal suspension containing 56 wt % silver nanoparticles in tetradecane solvent was used as a printing ink. It has electrical resistivity of 4.7 μΩ·cm. The substrates were obtained by performing a plasma enhanced chemical vapor deposition (PECVD) process with C4F8 and O2 under various treatment conditions. As results of the experiments, the surface shape and pattern of the inkjet-printed Ag lines were dominantly influenced by the surface energy of the substrates, among the printing variables. Accordingly even when the receding CA was non-zero, bulging instability of the lines occurred forming separate circular patterns or regular bulges connected by ridges. It is a new finding of this study, which is completely different with the bulging instability of inkjet lines with zero receding CA specified by previous researches. The bulging instability decreased by increasing surface temperature of the substrates or employing interlacing procedure instead of continuous procedure for printing. The interlacing procedure also was advantageous to fabricate thick and narrow Ag lines with well-defined shape through overprinting on a hydrophobic substrate. These results will contribute greatly to not only the production of various printed electronics containing high-aspect-ratio structures but also the improvement of working performance of the devices.

In this study, the evaporation behavior and the resulting morphology of inkjet-printed dielectric layers were controlled using a mixed-solvent system to fabricate uniform poly-4-vinylphenol (PVP) dielectric layers without any pinholes. The mixed-solvent system consisted of two different organic solvents: 1-hexanol and ethanol. The effects of inkjet-printing variables such as overlap condition, substrate temperature, and different printing sequences (continuous and interlacing printing methods) on the inkjet-printed dielectric layer were also investigated. Increasing volume fraction of ethanol (VFE) is likely to reduce the evaporation rate gradient and the drying time of the inkjet-printed dielectric layer; this diminishes the coffee stain effect and thereby improves the uniformity of the inkjet-printed dielectric layer. However, the coffee stain effect becomes more severe with an increase in the substrate temperature due to the enhanced outward convective flow. The overlap condition has little effect on the evaporation behavior of the printed dielectric layer. In addition, the interlacing printing method results in either a stronger coffee stain effect or wavy structures of the dielectric layers depending on the VFE of the PVP solution. All-inkjet-printed capacitors without electrical short circuiting can be successfully fabricated using the optimized PVP solution (VFE = 0.6); this indicates that the mixed-solvent system is expected to play an important role in the fabrication of high-quality inkjet-printed dielectric layers in various printed electronics applications.

Purpose The purpose of this study is to explore the influence of segmentation of the upstream and downstream parent artery and hemodynamic boundary conditions (BCs) on the evaluated hemodynamic factors for the computational fluid dynamics (CFD) analysis of intracranial aneurysms. Materials and methods Three dimensional patient-specific aneurysm models were analyzed by applying various combinations of inlet and outlet BCs. Hemodynamic factors such as velocity pattern, streamline, wall shear stress, and oscillatory shear index at the systolic time were visualized and compared among the different cases. Results Hemodynamic factors were significantly affected by the inlet BCs while there was little influence of the outlet BCs. When the inlet length was relatively short, different inlet BCs showed different hemodynamic factors and the calculated hemodynamic factors were also dependent on the inlet length. However, when the inlet length (L) was long enough (L>20D, where D is the diameter of inlet section), the hemodynamic factors became similar regardless of the inlet BCs and lengths. The error due to different inlet BCs was negligible. The effect of the outlet length on the hemodynamic factors was similar to that of the inlet length. Conclusion Simulated hemodynamic factors are highly sensitive to inlet BCs and upstream parent artery segmentation. The results of this work can provide an insight into how to build models and to apply BCs for more accurate estimation of hemodynamic factors from CFD simulations of intracranial aneurysms.

Paper and pencil have many advantages in triboelectric nanogenerators (TENGs) in terms of low-cost, light weight, and environment friendliness. In this work, a pencil-on-paper triboelectric nanogenerator (PP-TENG) with highly enhanced performance was introduced. In order to use paper as a friction layer and improve its triboelectric performance, a simple and rapid paper-coating process was utilized with polyvinylidene fluoride (PVDF), polyvinyledenedifluoride-trifluoroethylene (PVDF-TrFE), and poly(methyl methacrylate) (PMMA) solutions. The fabrication process of the PP-TENG was completed within 10 minutes via pencil drawing of an electrode followed by a solution coating. With an optimized electrode shape, the PP-TENG showed a maximum power density of 64 mW m−2, which is more than 19 times higher than that of the uncoated paper TENG. The electrical performance of the PP-TENG was sufficient to drive a few hundred LEDs and charge various capacitors. It was maintained after the paper was folded or even crumpled. The proposed PP-TENG is expected to be utilized with other wearable electronic devices.