Search

Composites based on acrylonitrile–butadiene rubber, carbon nanotubes, and manganese–zinc ferrite were fabricated and tested for electromagnetic interference (EMI) absorption shielding. First, carbon nanotubes and ferrite were solely used for the preparation of rubber composites. Then, carbon nanotubes were combined with magnetic filler and incorporated into the rubber matrix. The results revealed that carbon nanotubes act as reinforcing filler and significantly enhance the physical–mechanical properties of composites. The presence of carbon nanotubes in the rubber matrix also results in an outstanding increase in electrical conductivity and permittivity of composite materials, as a consequence of which the EMI absorption shielding was poor in the tested frequency range of 1 MHz to 3 GHz. On the other hand, ferrite-filled composites are able to efficiently absorb electromagnetic radiation emitted from various electronic and radiation sources. However, the tensile strength of the composites showed a decreasing trend with increasing content of ferrite. The combination of carbon nanotubes with manganese–zinc ferrite resulted in an improvement in the physical–mechanical properties of hybrid composites. As the permittivity of hybrid composites was still much higher in comparison with those filled only with ferrite, only the composite filled with 5 phr of carbon nanotubes and 100 phr of ferrite showed a slight EMI absorption shielding ability over the tested frequency range.

The present feature article offers a concise overview of recent research progress of the authors working in the design of macroporous conducting materials represented by polypyrrole-coated melamine sponges. The article highlights innovative results from the authors and suggests a perspective for future directions in the field of macroporous conducting polymer composites. The article also overviews this particular subject area and defines key challenges for this emerging field. The feasibility of diverse applications of polypyrrole/melamine sponges is demonstrated and includes deformation-sensitive materials, electromagnetic radiation shielding and electrically heated insulation materials. Cytotoxicity is addressed with respect to applications in biomedicine, and the adsorption of an organic dye serves as an example of the uses in environmental water-pollution treatment. A single-step deposition of polypyrrole during the oxidative polymerization of pyrrole provides the uniform coating of the sponge with an organic conducting phase. The conductivity of sponges was of the order of 10−3 S cm−1, increased with polypyrrole loading, and also by two orders of magnitude after the compression. Derived materials have also been prepared and tested. They are represented by polypyrrole-coated sponge converted by pyrolysis to a macroporous nitrogen-containing carbon, magnetic ferrosponge obtained by incorporation of magnetite, or the conventional globular polypyrrole coating replaced with polypyrrole nanotubes. Polypyrrole can also be simply decorated with silver nanoparticles. The macroporous conducting polypyrrole/melamine sponges and derived materials are considered to be of future scientific interest with broad application potential.

Czech Science FoundationGrant Agency of the Czech Republic [19-04859S, 21-09830S]; specific research project of the University of Chemistry and Technology, Prague [A2-FCHI-2021-003]

The study aims at the design of nanostructured hybrid materials that are both conducting and magnetic. Conducting polypyrrole nanotubes were prepared by the oxidation of pyrrole with iron(III) chlo...

As the most likely prospect for the construction of neuromorphic networks, the emulation of synaptic responses with memristors has attracted attention in both the microelectronic industries and the academic environment. To that end, a newly synthesized hybrid conjugated polymer with pendant carbazole rings, that is, poly(4-(6-(9H-carbazol-9-yl)hexyl)-4H-dithieno[3,2-b:2′,3′-d]pyrrole) (pC6DTP), was employed in the fabrication of a two-terminal memristor with a Al/pC6DTP/ITO configuration where the polymer was electrochemically doped. Signature biological synaptic responses to voltage spikes were demonstrated, such as potentiation & depression and spike timing dependent plasticity. The device was able to be programed through a 1 mV pulse, requiring only 100 fJ of energy. The voltage-dependent conductive nature of the polymer was speculated to occur through two synergistic mechanisms, one associated with the conjugation along the backbone of the conjugated polymer and one mechanism associated with the pendant heterocyclic rings.

In the present work, barium ferrite in constant loading was dosed to the rubber matrices based on NR, SBR and NBR. Sulfur, peroxide and mixed sulfur and peroxide curing systems were applied for cross-linking of rubber magnetic composites. The application of sulfur or peroxide curing system leads to the formation of different types of linkages between rubber chain segments. As the structure of the formed cross-links plays a significant role in determining the final properties of rubber articles, the main aim of the work was to use the combination of curing systems in order to suppress the disadvantages of both systems and possibly to highlight their benefits. The results showed that composition of curing system has considerable influence on cross-link density of composites, which was subsequently reflected in typical change of physical-mechanical properties and glass transition temperature. The tensile strength was improved with increasing amount of peroxide curing system. The reason can be attributed to the presence of co-agent zinc methacrylate, which exhibits strong adhesion to magnetic filler and thus it contributes to the improvement of compatibility and homogeneity on the interphase filler–rubber. On the hand, there was observed no influence of curing system composition or type of rubber matrix on magnetic characteristics of composites.

Rubber magnetic composites based on acrylonitrile butadiene rubber and strontium ferrite were cured with standard sulfur-based vulcanization systems as well as an organic peroxide. Zinc methacrylate (ZDMA) as a coagent was applied in both sulfur and peroxide vulcanization of rubber magnets. The aim was to evaluate the influence of ZDMA on curing characteristics and cross-link density of the prepared materials. Subsequently, physical-mechanical and magnetic properties were investigated. The results showed that ZDMA takes an active part in the cross-linking process of composites cured with an organic peroxide. Due to the presence of free radicals formed from peroxide decomposition, molecules of ZDMA polymerize into the nanostructures which can be physically adsorbed or chemically grafted onto rubber chains. Moreover, owing to zinc ions, ZDMA exhibits strong adhesion to ferrite filler and thus it contributes to the improvement of adhesion between the rubber and the filler on the interphase. The overall reinforcement of rubber magnetic composites was subsequently achieved. In the case of rubber magnets cured with the sulfur-based system, ZDMA acts as a conventional filler with a slight reinforcing effect due to the lack of free radicals required for its polymerization.

Cu

CuxCo1-xFe2O4 (x = 0.33, 0.67, 1)-reduced graphene oxide (rGO)-thermoplastic polyurethane (TPU) nanocomposites exhibiting highly efficient electromagnetic interference (EMI) shielding were prepared by a melt-mixing approach using a microcompounder. Spinel ferrite Cu0.33Co0.67Fe2O4 (CuCoF1), Cu0.67Co0.33Fe2O4 (CuCoF2) and CuFe2O4 (CuF3) nanoparticles were synthesized using the sonochemical method. The CuCoF1 and CuCoF2 exhibited typical ferromagnetic features, whereas CuF3 displayed superparamagnetic characteristics. The maximum value of EMI total shielding effectiveness (SET) was noticed to be 42.9 dB, 46.2 dB, and 58.8 dB for CuCoF1-rGO-TPU, CuCoF2-rGO-TPU, and CuF3-rGO-TPU nanocomposites, respectively, at a thickness of 1 mm. The highly efficient EMI shielding performance was attributed to the good impedance matching, conductive, dielectric, and magnetic loss. The demonstrated nanocomposites are promising candidates for a lightweight, flexible, and highly efficient EMI shielding material., Grantová Agentura České Republiky, GA ČR

In this work, nickel ferrite (NiFe2O4) nanoparticles were synthesized by dextrin from corn-mediated sol-gel combustion method and were annealed at 600, 800, and 1000 °C. The structural and physical characteristics of prepared nanoparticles were studied in detail. The average crystallite size was 20.6, 34.5, and 68.6 nm for NiFe2O4 nanoparticles annealed at 600 °C (NFD@600), 800 °C (NFD@800), and 1000 °C (NFD@1000), respectively. The electromagnetic interference shielding performance of prepared nanocomposites of NiFe2O4 nanoparticles (NFD@600 or NFD@800 or NFD@1000) in polypropylene (PP) matrix engineered with reduced graphene oxide (rGO) have been investigated; the results indicated that the prepared nanocomposites consisted of smaller-sized nickel ferrite nanoparticles exhibited excellent electromagnetic interference (EMI) shielding characteristics. The total EMI shielding effectiveness (SET) for the prepared nanocomposites have been noticed to be 45.56, 36.43, and 35.71 dB for NFD@600-rGO-PP, NFD@800-rGO-PP, and NFD@1000-rGO-PP nanocomposites, respectively, at the thickness of 2 mm in microwave X-band range (8.2-12.4 GHz). The evaluated values of specific EMI shielding effectiveness (SSE) were 38.81, 32.79, and 31.73 dB·cm3/g, and the absolute EMI shielding effectiveness (SSE/t) values were 388.1, 327.9, and 317.3 dB·cm2/g for NFD@600-rGO-PP, NFD@800-rGO-PP, and NFD@1000-rGO-PP, respectively. The prepared lightweight and flexible sheets can be considered useful nanocomposites against electromagnetic radiation pollution. Copyright © 2019 American Chemical Society., Ministry of Education, Youth and Sports of the Czech Republic-Program NPU I [LO1504]; TBU in Zlin, the Czech Republic [IGA/CPS/2019/007]

In this work, rubber composites were fabricated by incorporation of manganese-zinc ferrite alone and in combination with carbon-based fillers into acrylonitrile-butadiene rubber. Electromagnetic parameters and electromagnetic interference (EMI) absorption shielding effectiveness of composite materials were examined in the frequency range 1 MHz–3 GHz. The influence of ferrite and fillers combination on thermal characteristics and mechanical properties of composites was investigated as well. The results revealed that ferrite imparts absorption shielding efficiency to the composites in tested frequency range. The absorption shielding effectiveness and absorption maxima of ferrite filled composites shifted to lower frequencies with increasing content of magnetic filler. The combination of carbon black and ferrite also resulted in the fabrication of efficient EMI shields. However, the EMI absorption shielding effectiveness was lower, which can be ascribed to higher electrical conductivity and higher permittivity of those materials. The highest conductivity and permittivity of composites filled with combination of carbon nanotubes and ferrite was responsible for the lowest absorption shielding effectiveness within the examined frequency range. The results also demonstrated that combination of ferrite with carbon-based fillers resulted in the enhancement of thermal conductivity and improvement of mechanical properties. © 2021 by the authors. Licensee MDPI, Basel, Switzerland., Slovak Research and Development AgencySlovak Research and Development Agency [APVV-16-0136, APVV-19-0091], Agentúra na Podporu Výskumu a Vývoja, APVV: APVV-16-0136, APVV-19-0091

This paper demonstrates a three-dimensional electromagnetic interference shielding nanocomposite flexible sheet which is consisted of NiFe2O4 spinel ferrite nanoparticles, and carbon source materials such as graphite, graphene oxide and reduced graphene oxide in the elastomer matrix. The prepared nanocomposite exhibited ferromagnetic behavior. The total shielding effectiveness was up to 28.5 dB for the elastomer nanocomposite sheet having filler NiFe2O4 nanoparticles with reduced graphene oxide. The coexistence of electric and magnetic dipoles in the prepared shielding nanocomposite sheet can response highly to electromagnetic waves and consequently high electromagnetic loss. The high value of shielding efficiency is also related to dual interfaces of NiFe2O4 and reduced graphene oxide in the ternary NiFe2O4-Reduced Graphene Oxide-Elastomer nanocomposite. The investigated results indicate that the absorption attenuation is a dominant mechanism for electromagnetic interference shielding. The current study demonstrates a facile strategy to develop advanced lightweight electromagnetic interference shielding nanocomposite flexible sheet.

Superparamagnetic ZnFe2O4 spinel ferrite nanoparticles were prepared by the sonochemical synthesis method at different ultra-sonication times of 25 min (ZS25), 50 min (ZS50), and 100 min (ZS100). The structural properties of ZnFe2O4 spinel ferrite nanoparticles were controlled via sonochemical synthesis time. The average crystallite size increases from 3.0 nm to 4.0 nm with a rise of sonication time from 25 min to 100 min. The change of physical properties of ZnFe2O4 nanoparticles with the increase of sonication time was observed. The prepared ZnFe2O4 nanoparticles show superparamagnetic behavior. The prepared ZnFe2O4 nanoparticles (ZS25, ZS50, and ZS100) and reduced graphene oxide (RGO) were embedded in a polyurethane resin (PUR) matrix as a shield against electromagnetic pollution. The ultra-sonication method has been used for the preparation of nanocomposites. The total shielding effectiveness (SET) value for the prepared nanocomposites was studied at a thickness of 1 mm in the range of 8.2–12.4 GHz. The high attenuation constant (α) value of the prepared ZS100-RGO-PUR nanocomposite as compared with other samples recommended high absorption of electromagnetic waves. The existence of electric-magnetic nanofillers in the resin matrix delivered the inclusive acts of magnetic loss, dielectric loss, appropriate attenuation constant, and effective impedance matching. The synergistic effect of ZnFe2O4 and RGO in the PUR matrix led to high interfacial polarization and, consequently, significant absorption of the electromagnetic waves. The outcomes and methods also assure an inventive and competent approach to develop lightweight and flexible polyurethane resin matrix-based nanocomposites, consisting of superparamagnetic zinc ferrite nanoparticles and reduced graphene oxide as a shield against electromagnetic pollution. © 2021 by the authors. Licensee MDPI, Basel, Switzerland., Czech Science Foundation project at the Centre of Polymer Systems, Tomas Bata University in Zlin, Czech Republic [GA19-23647S]; Tomas Bata University in Zlin [IGA/CPS/2020/003], Grantová Agentura České Republiky, GA ČR: GA19-23647S; Univerzita Tomáše Bati ve Zlíně: IGA/CPS/2020/003

Superparamagnetic ZnFe2O4 spinel ferrite nanoparticles were prepared by the sonochemical synthesis method at different ultra-sonication times of 25 min (ZS25), 50 min (ZS50), and 100 min (ZS100). The structural properties of ZnFe2O4 spinel ferrite nanoparticles were controlled via sonochemical synthesis time. The average crystallite size increases from 3.0 nm to 4.0 nm with a rise of sonication time from 25 min to 100 min. The change of physical properties of ZnFe2O4 nanoparticles with the increase of sonication time was observed. The prepared ZnFe2O4 nanoparticles show superparamagnetic behavior. The prepared ZnFe2O4 nanoparticles (ZS25, ZS50, and ZS100) and reduced graphene oxide (RGO) were embedded in a polyurethane resin (PUR) matrix as a shield against electromagnetic pollution. The ultra-sonication method has been used for the preparation of nanocomposites. The total shielding effectiveness (SET) value for the prepared nanocomposites was studied at a thickness of 1 mm in the range of 8.2–12.4 GHz. The high attenuation constant (α) value of the prepared ZS100-RGO-PUR nanocomposite as compared with other samples recommended high absorption of electromagnetic waves. The existence of electric-magnetic nanofillers in the resin matrix delivered the inclusive acts of magnetic loss, dielectric loss, appropriate attenuation constant, and effective impedance matching. The synergistic effect of ZnFe2O4 and RGO in the PUR matrix led to high interfacial polarization and, consequently, significant absorption of the electromagnetic waves. The outcomes and methods also assure an inventive and competent approach to develop lightweight and flexible polyurethane resin matrix-based nanocomposites, consisting of superparamagnetic zinc ferrite nanoparticles and reduced graphene oxide as a shield against electromagnetic pollution.

The development of flexible, lightweight, and thin high-performance electromagnetic interference shielding materials is urgently needed for the protection of humans, the environment, and electronic devices against electromagnetic radiation. To achieve this, the spinel ferrite nanoparticles CoFe2O4 (CZ1), Co0.67Zn0.33Fe2O4 (CZ2), and Co0.33Zn0.67Fe2O4 (CZ3) were prepared by the sonochemical synthesis method. Further, these prepared spinel ferrite nanoparticles and reduced graphene oxide (rGO) were embedded in a thermoplastic polyurethane (TPU) matrix. The maximum electromagnetic interference (EMI) total shielding effectiveness (SET) values in the frequency range 8.2-12.4 GHz of these nanocomposites with a thickness of only 0.8 mm were 48.3, 61.8, and 67.8 dB for CZ1-rGO-TPU, CZ2-rGO-TPU, and CZ3-rGO-TPU, respectively. The high-performance electromagnetic interference shielding characteristics of the CZ3-rGO-TPU nanocomposite stem from dipole and interfacial polarization, conduction loss, multiple scattering, eddy current effect, natural resonance, high attenuation constant, and impedance matching. The optimized CZ3-rGO-TPU nanocomposite can be a potential candidate as a lightweight, flexible, thin, and high-performance electromagnetic interference shielding material. ©, Czech Science Foundation project at the Centre of Polymer Systems, Tomas Bata University in Zlin, Czech Republic [GA19-23647S], Grantová Agentura České Republiky, GA ČR: GA19-23647S; Univerzita Tomáše Bati ve Zlíně

Macroporous open-cell melamine sponges were coated with a conducting polymer, polypyrrole, during in-situ oxidative polymerization of pyrrole. Two samples, differing in polypyrrole content, 8.2 and 27.4 wt%, were prepared. They were exposed to various temperatures up to 700 °C in an inert atmosphere. The macroporous structure and mechanical integrity were preserved after this process. This converted both the polypyrrole coating and the melamine sponge to macroporous nitrogen-containing carbons. The changes in molecular structure in the course of carbonization were followed by elemental analysis and FTIR and Raman spectra. The specific surface area of polypyrrole-coated sponge increased from ca. 90 to ca. 300 m2 g−1 along with accompanying increase in the porosity. The conductivity of the sponges was recorded as a function of compression in a newly developed apparatus. The sponge containing 27.4 wt% pyrrole had conductivity of the order of 10−2 S·cm−1 at 0.1 MPa pressure, which was reduced by four orders of magnitude when exposed to 400–500 °C and nearly recovered after the temperature reached 700 °C. The sponges were tested in electromagnetic radiation shielding and displayed both radiation absorption and, to a lower extent, radiation reflection proportional mainly to the samples’ conductivity.

In this work, various tunable sized spinel ferrite MnFe2O4 nanoparticles (namely MF20, MF40, MF60 and MF80) with reduced graphene oxide (RGO) were embedded in a polypropylene (PP) matrix. The particle size and structural feature of magnetic filler MnFe2O4 nanoparticles were controlled by sonochemical synthesis time 20 min, 40 min, 60 min and 80 min. As a result, the electromagnetic interference shielding characteristics of developed nanocomposites MF20-RGO-PP, MF40-RGO-PP, MF60-RGO-PP and MF80-RGO-PP were also controlled by tuning of magnetic/dielectric loss. The maximum value of total shielding effectiveness (SET) was 71.3 dB for the MF80-RGO-PP nanocomposite sample with a thickness of 0.5 mm in the frequency range (8.2–12.4 GHz). This lightweight, flexible and thin nanocomposite sheet based on the appropriate size of MnFe2O4 nanoparticles with reduced graphene oxide demonstrates a high-performance advanced nanocomposite for cutting-edge electromagnetic interference shielding application. © 2020 by the authors. Licensee MDPI, Basel, Switzerland., Czech Science Foundation project at the Centre of Polymer Systems, Tomas Bata University in Zlin, Czech Republic [GA19-23647S]

The gadolinium (Gd3+) substituted zinc ferrite nanoparticles (ZnFe2−xGdxO4) for Gd3+ (x = 0.00, 0.05, 0.10, 0.20) have been synthesized by honey mediated sol–gel auto-combustion method. The X-ray diffraction study revealed the formation of spinel ferrite crystal structure. The Raman spectroscopy and Fourier transform infrared spectroscopy study well support the XRD results analysis. The field emission scanning electron microscopy micrograph revealed spherical morphology and grain size around 10–30 nm for ZnFe2−xGdxO4 (x = 0.10) nanoparticles. The presence of Zn2+ and Fe3+ oxidation state in synthesized nanoparticles was confirmed by X-ray photoelectron spectroscopy. Magnetic properties of the Gd3+ substituted zinc ferrite nanoparticles were investigated by vibrating sample magnetometer at room temperature. The conversion of magnetic hysteresis curves from ferromagnetic to a paramagnetic with the substitution of Gd3+ in zinc ferrite nanoparticles was observed. Frequency dependent dielectric constant and ac conductivity measurements revealed that Gd3+ substitution improved the value of dielectric constant and ac conductivity of the Gd3+ substituted zinc ferrite nanoparticles. Further, the existence of two semicircles in Cole–Cole plot demonstrated the role of both grains and grain boundaries to conduction process in synthesized Gd3+ ion substituted zinc ferrite nanoparticles. Furthermore, the grain relaxation time (τg), grain boundary relaxation time (τgb), grain resistance (Rg), grain capacitance (Cg), grain boundary resistance (Rgb) and grain boundary capacitance (Cgb) for synthesized ZnFe2−xGdxO4 (x = 0.00, 0.05, 0.10, 0.20) nanoparticles have been calculated using modulus spectroscopy analysis.

In this work, a facile and green method for gadolinium doped cobalt ferrite (CoFe2-xGdxO4; x=0.00, 0.05, 0.10, 0.15, 0.20) nanoparticles by using ultrasonic irradiation was reported. The impact of Gd3+ substitution on the structural, magnetic, dielectric and electrical properties of cobalt ferrite nanoparticles was evaluated. The sonochemically synthesized spinel ferrite nanoparticles were characterized by X-ray Diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM). X-ray diffraction (XRD) study confirmed the formation of single phase spinel ferrite of CoFe2-xGdxO4 nanoparticles. XRD results also revealed that ultrasonic irradiation seems to be favourable to achieve highly crystalline single crystal phase gadolinium doped cobalt ferrite nanoparticles without any post annealing process. Fourier Transform Infrared and Raman Spectra confirmed the formation of spinel ferrite crystal structure. X-ray photoelectron spectroscopy revealed the impact of Gd3+ substitution in CoFe2O4 nanoparticles on cation distribution at the tetrahedral and octahedral site in spinel ferrite crystal system. The electrical properties showed that the Gd3+ doped cobalt ferrite (CoFe2-xGdxO4; x=0.20) exhibit enhanced dielectric constant (277 at 100Hz) and ac conductivity (20.2×10-9S/cm at 100Hz). The modulus spectroscopy demonstrated the impact of Gd3+ substitution in cobalt ferrite nanoparticles on grain boundary relaxation time, capacitance and resistance. Magnetic property measurement revealed that the coercivity decreases with Gd3+ substitution from 234.32Oe (x=0.00) to 12.60Oe (x=0.05) and further increases from 12.60Oe (x=0.05) to 68.62Oe (x=0.20). Moreover, saturation magnetization decreases with Gd3+ substitution from 40.19emu/g (x=0.00) to 21.58emu/g (x=0.20). This work demonstrates that the grain size and cation distribution in Gd3+ doped cobalt ferrite nanoparticles synthesized by sonochemical method, is effective in controlling the structural, magnetic, and electrical properties, and can be find very promising applications.