Search

Self-passivating W-11.4Cr-0.6Y (in wt.%) alloy is a plasma-facing candidate armour material in fusion power plants. In the present work, the as-sintered material, fabricated via ball milling and field-assisted sintering, was annealed at 1000 °C for varying durations to induce phase decomposition. This process leads to the transformation of the initially homogeneous microstructure into two distinct phases: the W-rich phase (αW, Cr) and the Cr-rich phase (αCr, W). Cr-rich phases preferentially form at grain boundaries, where yttrium oxides are also located, and gradually coarsen to the submicron range with increasing annealing time. The chemical compositions of both phases remain relatively stable after 75 h of annealing. The Cr content in (αW, Cr) is 18.6 at.% at 75 h and 17.8 at.% at 100 h. Compared to the as-sintered state, the 100 h-annealed material exhibits significant softening at room temperature and demonstrates increased flexural strength across all tested temperatures, but lower fracture toughness at elevated temperatures. The oxidation behavior of the 100 h-annealed material under humid air at 1000 °C reveals two stages in its TGA curve: inital growth of the inner oxide layer followed by subsequent development of the protecting chromia layer. In contrast, the as-sintered material exhibits a continuous, linear mass increase throughout the oxidation process. These findings present promising prospects of the decomposed microstructure for first wall applications.

The self-passivating yttrium-containing WCr alloy has been developed and researched as a potential plasma-facing armour material for fusion power plants. This study explores the use of yttria (Y2O3) powders instead of yttrium elemental powders in the mechanical alloying process to assess their applicability for this material. Fabricated through field-assisted sintering, WCr-Y2O3 ingots show Y2O3 and Cr-containing oxides (Cr-O and Y-Cr-O) dispersed at grain boundaries (GBs), while WCrY ingots contain Y-O particles at grain boundaries, both resulting from unavoidable oxidation during fabrication. WCr-Y2O3 demonstrates higher flexural strength than WCrY across all temperature ranges, ranging from 850 to 1050 MPa, but lower fracture toughness, between 3 and 4 MPa·√m. Enhanced oxidation resistance is observed in WCr-Y2O3, with lower mass gain as compared to WCrY during the 20-hour oxidation test. This study confirms the effectiveness of both yttria and yttrium in the reactive element effect (REE) for the passivation of WCr alloy, suggesting the potential of Y2O3-doped WCr for first wall applications in a fusion power plant.

The use of tungsten fiber-reinforced tungsten composites (Wf/W) has been demonstrated to significantly enhance the mechanical properties of tungsten (W) by incorporating W-fibers into the W-matrix. However, prior research has been restricted by the usage of single fiber-based textile fabrics, consisting of 150 µm warp and 50 µm weft filaments, with limited homogeneity, reproducibility, and mechanical properties in bulk structures due to the rigidity of the 150 µm W-fibers. To overcome this limitation, two novel textile preforms were developed utilizing radial braided W-yarns with 7 core and 16 sleeve filaments (R.B. 16 + 7), with a diameter of 25 µm each, as the warp material. In this study, bulk composites of two different fabric types were produced via a layer-by-layer CVD process, utilizing single 50 µm filaments (type 1) and R.B. 16 + 7 yarns (type 2) as weft materials. The produced composites were sectioned into KLST-type specimens based on DIN EN ISO 179-1:2000 using electrical discharge machining (EDM) and subjected to three-point bending tests. Both composites demonstrated enhanced mechanical properties with pseudo-ductile behavior at room temperature and withstood over 10,000 load cycles between 50–90% of their respective maximum load without sample fracture in three-point cyclic loading tests. Furthermore, a novel approach to predict the fatigue behavior of the material under cyclic loading was developed based on the high reproducibility of the composites produced, especially for the composite based on type 1. This approach provides a new benchmark for upscaling endeavors and may enable a better prediction of the service life of the produced components made of Wf/W in the future. In comparison, the composite based on fabric type 1 demonstrated superior results in manufacturing performance and mechanical properties. With a high relative average density (>97%), a high fiber volume fraction (14–17%), and a very homogeneous fiber distribution in the CVD-W matrix, type 1 shows a promising option to be further tested in high heat flux tests and to be potentially used as an alternative to currently used materials for the most stressed components of nuclear fusion reactors or other potential application fields such as concentrated solar power (CSP), aircraft turbines, the steel industry, quantum computing, or welding tools. Type 2 composites have a higher layer spacing compared to type 1, resulting in gaps within the matrix and less homogeneous material properties. While type 2 composites have demonstrated a notable enhancement over 150 µm fiber-based composites, they are not viable for industrial scale-up unlike type 1 composites.

Functionally graded tungsten/steel composites are attractive to be used as an interlayer to join tungsten (W) and steel for the first wall of future fusion reactor to reduce the thermally induced stresses arising from the different coefficient of thermal expansion (CTE) of W and steel. W/steel composites, with three W contents: 25, 50 and 75 vol% W, will serve as individual sublayers of this functionally graded material. Therefore, the present work exploits an emerging sintering technique, field-assisted sintering technology, to produce these composites. Firstly, a systematic parameter study was conducted aiming to reduce the residual porosity to a minimum while keeping the formation of intermetallic phases at the W/steel interface at a low level. The optimized composites 25, 50 and 75 vol% W achieved a relative density of 99%, 99% and 96%, respectively. Secondly, mechanical tests at elevated temperatures reveal that these composites are ductile above 300 °C, which is the minimum operating temperature of the first wall. Lastly, the measured CTE, specific heat capacity and thermal conductivity were consistent with the theoretically expected values.

Tungsten-fibre-reinforced tungsten composites (Wf/W) have been in development to overcome the inherent brittleness of tungsten as one of the most promising candidates for the first wall and divertor armour material in a future fusion power plant. As the development of Wf/W continues, the fracture toughness of the composite is one of the main design drivers. In this contribution, the efforts on size upscaling of Wf/W based on Chemical Vapour Deposition (CVD) are shown together with fracture mechanical tests of two different size samples of Wf/W produced by CVD. Three-point bending tests according to American Society for Testing and Materials (ASTM) Norm E399 for brittle materials were used to obtain a first estimation of the toughness. A provisional fracture toughness value of up to 346MPam1/2 was calculated for the as-fabricated material. As the material does not show a brittle fracture in the as-fabricated state, the J-Integral approach based on the ASTM E1820 was additionally applied. A maximum value of the J-integral of 41kJ/m2 (134.8MPam1/2) was determined for the largest samples. Post mortem investigations were employed to detail the active mechanisms and crack propagation.

Tungsten-steel metal matrix composites are consolidated using electro-discharge sintering. At first steel and tungsten powders are sintered separately and then 25 vol% W, 50 vol% W and 75 vol% W mixed powders are sintered. A thorough process parametric study is carried out involving analysis of the influence of particle size distribution, sintering pressure, and discharge energy on the maximum discharge current and obtained residual porosity. Thermal expansion coefficient and the specific heat capacity of the optimized sintered composites are almost same as their theoretical values, however the thermal conductivities and the mechanical properties are lower than the expected values.

During the spark plasma sintering (SPS) consolidation process, the pressure affects the densification and microstructure evolution of the sintered body. In this paper, the W-Cr-Y-Zr alloy powder was heated to 1000 °C under different applied pressure conditions using spark plasma sintering process, and the effect of pressure on the densification process and microstructure was analyzed. Due to the low sintering temperature, the crystalline size of all the produced W-Cr-Y-Zr alloy is less than 10 nm, which is close to that of the original powders. Cr-rich phase can be detected in the sintered samples due to spinodal decomposition. It is found in this work that the external pressure will increase the contact area between the powder particles, resulting in a higher local pressure at the particle contact, which promotes densification by sliding between the particles under the condition of softening of the particle surface. Additionally, according to the viscous flow theory, the viscous flow activation energy decreases with the increase of pressure. This is because the pressure provides additional driving force to the powder viscous flow process and accelerates the powder shrinkage.

Tungsten (W) has the unique combination of excellent thermal properties, low sputter yield, low hydrogen retention, and acceptable activation. Therefore, W is presently the main candidate for the first wall and armor material for future fusion devices. However, its intrinsic brittleness and its embrittlement during operation bears the risk of a sudden and catastrophic component failure. As a countermeasure, tungsten fiber-reinforced tungsten (Wf/W) composites exhibiting extrinsic toughening are being developed. A possible Wf/W production route is chemical vapor deposition (CVD) by reducing WF6 with H2 on heated W fabrics. The challenge here is that the growing CVD-W can seal gaseous domains leading to strength reducing pores. In previous work, CVD models for Wf/W synthesis were developed with COMSOL Multiphysics and validated experimentally. In the present article, these models were applied to conduct a parameter study to optimize the coating uniformity, the relative density, the WF6 demand, and the process time. A low temperature and a low total pressure increase the process time, but in return lead to very uniform W layers at the micro and macro scales and thus to an optimized relative density of the Wf/W composite. High H2 and low WF6 gas flow rates lead to a slightly shorter process time and an improved coating uniformity as long as WF6 is not depleted, which can be avoided by applying the presented reactor model.

The tungsten (W) foil laminate is an advanced material concept developed as a solution for the low temperature brittleness of W. However, the deformed W foils inevitably undergo microstructure deterioration (crystallization) during the joining process at a high temperature. In this work, joining of the W foil laminate was carried out in a field-assisted sintering technology (FAST) apparatus. The joining temperature was optimized by varying the temperature from 600 to 1400 °C. The critical current for mitigating the microstructure deterioration of the deformed W foil was evaluated by changing the sample size. It is found that the optimal joining temperature is 1200 °C and the critical current density is below 418 A/cm2. According to an optimized FAST joining process, the W foil laminate with a low microstructure deterioration and good interfacial bonding can be obtained. After analyzing these current profiles, it was evident that the high current density (sharp peak current) is the reason for the significant microstructure deterioration. An effective approach of using an artificial operation mode was proposed to avoid the sharp peak current. This study provides the fundamental knowledge of FAST principal parameters for producing advanced materials.

Tungsten (W) is currently deemed the main candidate for the plasma-facing armor material of the first wall of future fusion reactors, such as DEMO. Advantages of W include a high melting point, high thermal conductivity, low tritium retention, and low erosion yield. However, was an accident to occur, air ingress into the vacuum vessel could occur and the temperature of the first wall could reach 1200K to 1450K due to nuclear decay heat. In the absence of cooling, the temperature remains in that range for several weeks. At these temperatures, the radioactive tungsten oxidizes and then volatilizes. Smart W alloys are therefore being developed. Smart alloys are supposed to preserve properties of W during plasma operation while suppressing tungsten oxide formation in case of an accident. This study focuses on investigations of thin film smart alloys produced by magnetron sputtering. These alloys provide an idealistic system with a homogeneous distribution of the elements W, chromium (Cr), and yttrium (Y) on an atomic scale. The recommended composition is W with 12 weight % of Cr and 0.5 weight % of Y. Passivation and a suppression of WO3 sublimation is shown. For the first time, the mechanisms yielding the improved oxidation resistance are analyzed in detail. A protective Cr2O3 layer forms at the surface. The different stages of the oxidation processes up to the failure of the protective function are analyzed for the first time. Using 18O as a tracer, it is shown for the first time that the oxide growth occurs at the surface of the protective oxide. The Cr is continuously replenished from the bulk of the sample, including the Cr-rich phase which forms during exposure at 1273K. A homogenous distribution of yttria within the W-matrix, which is preserved during oxidation, is a peculiarity of the analyzed alloy. Further, an Y-enriched nucleation site is found at the interface between metal and oxide. This nucleation sites are deemed to be crucial for the improved oxidation resistance.