Search

Phosphorus (P) scarcity and eutrophication have triggered the development of new approaches for phosphorus recovery. This study investigated the impact of calcium-doped biochar, produced from biosolids via microwave pyrolysis at 700 °C for 20 min, on phosphorus recovery. The phosphorus removal isotherms, removal kinetics and the impact of initial pH of phosphorus solution on phosphorus recovery were studied. The phosphorus recovery was proportional to the calcium content in biochar, leading predominantly to the production of brushite. Precipitation was the main mechanism of phosphorus removal by calcium-doped biochar. Phosphorus removal capacity of biochar reached equilibrium after 8 h of contact time and was described by a pseudo-second-order kinetic model. The Langmuir isotherm model fitted the experimental data well with a maximum adsorption capacity of 147 mg-P/g for biochar BC20 (20 wt% Ca(OH)2). The results of phosphorus removal from a real wastewater demonstrated that using Ca-doped biochar for phosphorus removal from contaminated streams is a promising alternative for phosphorus recovery as well as for biosolids management. Heavy metal leaching from Ca-doped biochar was much lower than from undoped biochar, and decreased as the amount of calcium in biochar increased.

Microwave assisted pyrolysis (MWAP) is an alternative heating approach to convert biosolids into value-added products, such as biochar, biogas and bio-oil. Studying the dielectric properties of biosolids is fundamental to understand the behaviour of this material under microwave irradiation and to design microwave assisted pyrolysis systems. This study examined the dielectric properties of biosolids with changes in moisture content and applied microwave frequency. Results demonstrated that the dielectric constant decreases with decreasing moisture content and with increasing microwave frequency, but the dielectric loss factor of dry biosolids is almost zero. Simulations demonstrated that moisture content of biosolids impacts on the distribution and intensity of electromagnetic field. Because of the poor dielectric properties of dry biosolids, a microwave susceptor must be added to the biosolids to attract microwave energy so that the materials can reach temperatures required for pyrolysis. Therefore, this study also investigated the impact of four microwave susceptors (activated carbon, charcoal, biochar and glycerol) on biosolids pyrolysis and on biochar properties produced from biosolids via microwave assisted pyrolysis at 600 °C. The choice of microwave susceptor influences the heating rate of biosolids and the specific surface area of the resultant biochar. Results show that activated carbon favours the heating process, increases surface area, and the biochar produced with activated carbon has the highest carbon stability and energy value.

The contamination of water with silver has increased due to the widespread applications of products with silver employed as antimicrobial agent. Adsorption is a cost-effective method for silver removal from aqueous solution. In this study biochar, produced from the microwave assisted pyrolysis of biosolids, was used for silver removal from an aqueous solution. The adsorption kinetics, isotherms and thermodynamics were investigated to better understand the silver removal process by biochar. X-ray diffraction results demonstrated that silver removal was a combination two consecutive mechanisms, reduction and physical adsorption. The Langmuir model fitted the experimental data well, showing that silver removal was predominantly a surface mechanism. The thermodynamic investigation demonstrated that silver removal by biochar was an exothermic process. The final nanocomposite Ag-biochar (biochar plus silver) was used for methylene blue adsorption and photodegradation. This study showed the potential of using biochar produced from biosolids for silver removal as a promising solution to mitigate water pollution and an environmentally sustainable approach for biosolids management and re-use.

The amount of biosolids increases every year, and social and environmental concerns are also rising due to heavy metals and pathogen contamination. Even though biosolids are considered as a waste material, they could be used as a precursor in several applications, especially in agriculture due to the presence of essential nutrients. Microwave assisted pyrolysis (MWAP) is a promising technology to safely manage biosolids, while producing value-added products, such as biochar, that can be used to improve soil fertility. This study examined the impact of pyrolysis temperature between 300 °C and 800 °C on the chemical and physical properties of biochar obtained from biosolids via MWAP. Preliminary phosphorus adsorption tests were carried out with the biochar produced from biosolids. This research demonstrated that pyrolysis temperature affects biochar specific surface area, ash and volatiles content, but does not impact heavily on the pH, chemical composition and crystalline phases of the resultant biochar. Biochar yield decreases as the pyrolysis temperature increases. Phosphorus adsorption capacity of biochar was approximately around 15 mg/g of biochar. Biochar resulting from MWAP is a potential candidate for land application with an important role in water and nutrient retention, due to the high surface area.

The measurement of dielectric properties of materials is critical to understanding the electromagnetic field distribution in the materials. Reliable knowledge of the dielectric constant is also important when designing a microwave pyrolysis unit for effective pyrolysis of materials of interest. The dielectric probe technique was used to evaluate the dielectric properties of biosolids. Biosolid samples were collected from various sources and the dielectric properties were measured across the microwave frequency range of 1.0 GHz to 10.0 GHz. The dielectric constant of the materials varied in the range from 80 to 2 and depended mainly on the origin of the sample, the electrical conductivity and the moisture content of the material. A mathematical model was developed to accurately predict the values of complex permittivity. This model was verified using the measured data.