Search

A method for calculating stored magnetic energy in a thin superconducting film based on quantitative magneto-optical imaging is developed. Energy and magnetic moment are determined with these calculations for full hysteresis loops in a thin film of the superconductor NbN. Huge losses in energy are observed when dendritic avalanches occur. Magnetic energy, magnetic moment, sheet current and magnetic flux distributions, all extracted from the same calibrated magneto-optical images, are analyzed and discussed. Dissipated energy and the loss in moment when dendritic avalanches occur are related to each other. Calculating these losses for specific spatially-resolved flux avalanches is a great advantage, because of their unpredictable and non-reproducible nature. The relative losses in energy are much higher than the relative losses in moment. peerReviewed

In order to improve the frequency-division multiplexing (FDM) in transition edge sensor (TES) imaging arrays, it is suggested to replace commonly used SQUID amplifiers with a semiconductor high-frequency cooled amplifier. This would result in a single 10-GHz bandwidth amplifier serving the array of more than 1000 detectors. The basic idea is to implement an antenna-coupled TES as a load for a high-Q resonator, weakly coupled to a microwave transmission line. This high-frequency scheme substitutes the traditional wire connections to the TES. The NEP as low as 2×10-19 W/Hz0.5 is estimated at ambient temperature of 300 mK for submicron-size TES absorber made of Ti; the NEP is limited by 3 K noise temperature of the amplifier. To verify the new concept, prototype TES devices made of Nb are developed and tested above 4 K. The NEP of about 1.5×10-15 W/Hz0.5 is estimated for the experimental micron-size prototype devices made of Nb at 4.5 K. The IV -curves of the TES at different temperatures are recovered using the RF and heat balance models along with the experimental R(T) data; presence of the negative electrothermal feedback is verified.

Reduction of the critical current in narrow superconducting NbN lines with sharp and rounded bends with respect to the critical current in straight lines was studied at different temperatures.We compare our experimental results with the reduction expected in the framework of the London model and the Ginsburg-Landau model. We have experimentally found that the reduction is significantly less than either model predicts. We also show that in our NbN lines the bends mostly contribute to the reduction of the critical current at temperatures well below the superconducting transition temperature.

The high-power long pulse RF loss properties of CVD diamond windows for ECR heating and plasma stabilization in large fusion devices have been measured by established Fabry-Perot methods [1,2,3]. The dielectric loss is strongly influenced by the surface chemistry of the diamond. Special surface passivation techniques are investigated due to the reduction of the electrical surface conductivity and therefore of the RF losses.

We have investigated asymmetrically shunted Nb/Al-AlO$_x$/Nb direct current (dc) superconducting quantum interference devices (SQUIDs). While keeping the total resistance $R$ identical to a comparable symmetric SQUID with $R^{-1} = R_1^{-1} + R_2^{-1}$, we shunted only one of the two Josephson junctions with $R = R_{1,2}/2$. Simulations predict that the optimum energy resolution $\epsilon$ and thus also the noise performance of such an asymmetric SQUID can be 3--4 times better than that of its symmetric counterpart. Experiments at a temperature of 4.2\,K yielded $\epsilon \approx 32\,\hbar$ for an asymmetric SQUID with an inductance of $22\,\rm{pH}$. For a comparable symmetric device $\epsilon = 110\,\hbar$ was achieved, confirming our simulation results., Comment: 5 pages, 4 figures

In long Josephson junctions with multiple discontinuities of the Josephson phase, fractional vortex molecules are spontaneously formed. At each discontinuity point a fractional Josephson vortex carrying a magnetic flux $|\Phi, Comment: submitted to Phys. Rev. B

We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.

Aluminum nitride (AlN) has recently emerged as a promising material for integrated photonics due to a large bandgap and attractive optical properties. Exploiting the wideband transparency, we demonstrate waveguiding in AlN-on-Insulator circuits from near-infrared to ultraviolet wavelengths using nanophotonic components with dimensions down to 40 nm. By measuring the propagation loss over a wide spectral range, we conclude that both scattering and absorption of AlN-intrinsic defects contribute to strong attenuation at short wavelengths, thus providing guidelines for future improvements in thin-film deposition and circuit fabrication.

Appearance of dendritic magnetic flux avalanches in superconducting films, which are associated with thermo-magnetic instability (TMI), very often indicates serious limitations for the ultimate performance of superconducting devices made of type-II superconducting thin films. We demonstrate that the stability can be controlled by a thorough adjustment of samples morphology at nano-scale, which affects internal material parameters. By this, the metal coating, commonly used as for stabilization, becomes redundant. Most importantly, we directly show by the mean of magneto-optical imaging that introduction of nano-scaled disorder dramatically changes the mode of magnetic flux propagation in the superconductors, from uniform motion of individual vortices to correlated jumps of relatively large vortex bundles, revealing the triggering mechanism of TMI.

For high-performance superconducting quantum devices based on Josephson junctions (JJs) decreasing lateral sizes is of great importance. Fabrication of sub-\mu m JJs is challenging due to non-flat surfaces with step heights of up to several 100 nm generated during the fabrication process. We have refined a fabrication process with significantly decreased film thicknesses, resulting in almost flat surfaces at intermediate steps during the JJ definition. In combination with a mix-&-match process, combining electron-beam lithography (EBL) and conventional photolithography, we can fabricate JJs with lateral dimensions down to 0.023 \mu m^2. We propose this refined process as an alternative to the commonly used chemical-mechanical polishing (CMP) procedure. We present transport measurements of JJs at 4.2 K that yield critical-current densities in the range from 50 to 10^4 A/cm^2. Our JJ process yields excellent quality parameters, Rsg/Rn up to ~50 and Vgap up to 2.81 mV, and also allows the fabrication of high-quality sub-\mu m wide long JJs (LJJs) for the study of Josephson vortex behavior. The developed technique can also be used for similar multilayer processes and is very promising for fabricating sub-\mu m JJs for quantum devices such as SQUIDs, qubits and SIS mixers.