Search

Many techniques have been studied for recovering information from shared media such as optical fiber that carries different types of communication, sensing, and data streaming. This article focuses on a simple method for retrieving the targeted information with the least necessary number of significant samples when using statistical population sampling. Here, the focus is on the statistical denoising and detection of the fiber Bragg grating (FBG) power spectra. The impact of the two-sided and one-sided sliding window technique is investigated. The size of the window is varied up to one-half of the symmetrical FBG power spectra bandwidth. Both, two- and one-sided small population sampling techniques were experimentally investigated. We found that the shorter sliding window delivered less processing latency, which would benefit real-time applications. The calculated detection thresholds were used for in-depth analysis of the data we obtained. It was found that the normality three-sigma rule does not need to be followed when a small population sampling is used. Experimental demonstrations and analyses also showed that novel denoising and statistical threshold detection do not depend on prior knowledge of the probability distribution functions that describe the FBG power spectra peaks and background noise. We have demonstrated that the detection thresholds’ adaptability strongly depends on the mean and standard deviation values of the small population sampling.

Silicon nitride (Si3N4) is an ideal candidate for the development of low-loss photonic integrated circuits. However, efficient light coupling between standard optical fibers and Si3N4 chips remains a significant challenge. For vertical grating couplers, the lower index contrast yields a weak grating strength, which translates to long diffractive structures, limiting the coupling performance. In response to the rise of hybrid photonic platforms, the adoption of multi-layer grating arrangements has emerged as a promising strategy to enhance the performance of Si3N4 couplers. In this work, we present the design of high-efficiency surface grating couplers for the Si3N4 platform with an amorphous silicon (α-Si) overlay. The surface grating, fully formed in an α-Si waveguide layer, utilizes subwavelength grating (SWG)-engineered metamaterials, enabling simple realization through single-step patterning. This not only provides an extra degree of freedom for controlling the fiber–chip coupling but also facilitates portability to existing foundry fabrication processes. Using rigorous three-dimensional (3D) finite-difference time-domain (FDTD) simulations, a metamaterial-engineered grating coupler is designed with a coupling efficiency of −1.7 dB at an operating wavelength of 1.31 µm, with a 1 dB bandwidth of 31 nm. Our proposed design presents a novel approach to developing high-efficiency fiber–chip interfaces for the silicon nitride integration platform for a wide range of applications, including datacom and quantum photonics.

This paper describes design, theoretical analysis, and experimental evaluation of a π-Phase-Shifted Fiber Bragg Grating (π-PSFBG) inscribed in the standard telecom fiber for slow light generation. At first, the grating was designed for its use in the reflection mode with a central wavelength of 1552 nm and a pass band width of less than 100 pm. The impact of fabrication imperfections was experimentally investigated and compared to model predictions. The optical spectra obtained experimentally show that the spectral region used for slow light generation is narrower (less than 10 pm), thus allowing for too-low levels of slow light optical-output power. In the next step, the optimization of the grating design was conducted to account for fabrication errors, to improve the grating’s spectral behavior and its temporal performance, and to widen the spectral interval for slow light generation in the grating’s transmission mode. The targeted central wavelength was 1553 nm. The π-PSFBG was then commercially fabricated, and the achieved parameters were experimentally investigated. For the region of (1551–1554) nm, a 15-fold increase in the grating’s pass band width was achieved. We have shown that a pair of retarded optical pulses were generated. The measured group delay was found to be ~10.5 ps (compared to 19 ps predicted by the model). The π-PSFBG operating in its transmission mode has the potential to operate as tunable delay line for applications in RF photonics, ultra-fast signal processing, and optical communications, where tunable high precision delay lines are highly desirable. The π-PSFBG can be designed and used for the generation of variable group delays from tens to hundreds of ps, depending on application needs.

High data rate coverage, security, and energy efficiency will play a key role in the continued performance scaling of next-generation mobile systems. Dense, small mobile cells based on a novel network architecture are part of the answer. Motivated by the recent mounting interest in free-space optical (FSO) technologies, this paper addresses a novel mobile fronthaul network architecture based on FSO, spread spectrum codes, and graphene modulators for the creation of dense small cells. The network uses an energy-efficient graphene modulator to send data bits to be coded with spread codes for achieving higher security before their transmission to remote units via high-speed FSO transmitters. Analytical results show the new fronthaul mobile network can accommodate up to 32 remote antennas under error-free transmissions with forward error correction. Furthermore, the modulator is optimized to provide maximum efficiency in terms of energy consumption per bit. The optimization procedure is carried out by optimizing both the amount of graphene used on the ring resonator and the modulator’s design. The optimized graphene modulator is used in the new fronthaul network and requires as low as 4.6 fJ/bit while enabling high-speed performance up to 42.6 GHz and remarkably using one-quarter of graphene only.

In this proof-of-principle paper, the application of 2-D optical code-division multiple-access (OCDMA) modulation to long-range automotive time-of-flight (ToF) light detection and ranging (LiDAR) is studied. The regulations and physical constraints that govern the design parameters are reviewed. Using 2-D carrier-hopping prime codes (CHPCs), the modulation model and a novel 2-D hard-limiting decoder are designed and validated with OptiSystem$^{\rm {TM}}$ simulations. Based on the design parameters, the 2-D CHPCs have six times as many distinct sequences (for sensor identification) as 1-D code sequences. Analytical and simulation studies show that the proposed 2-D OCDMA modulation model can eliminate the near-far (power) problem and support more LiDAR sensors with distinctive ToF tags, greater interference robustness for more simultaneous ToF measurements, and better performance than the 1-D counterparts. The simulation results show that the 2-D model can support four times as many simultaneous emitting sensors without false detections as the 1-D model. In summary, the 2-D OCDMA modulation has more benefits and is more cost efficient overall, even though it is more complex.

Recent studies show that temperature variation in ultrafast incoherent fiber-optic code-division multiple-access (FO-CDMA) systems using picosecond multiwavelength codes is a realistic problem even though dispersion-compensating fiber is utilized. The phenomenon creates distortions in auto- and cross-correlation functions and then worsens system performance. A physical-layer mitigation approach has been reported by using a recently demonstrated semiconductor-optical-amplifier-based tunable dispersion compensator to fully recover the auto-correlation peaks. Applying the concept of “chip granularity” to account for the effects of temperature variation to the cross-correlation functions, this paper formulates a new performance-analytical model for such FO-CDMA systems. The model also supports adjustable quality-of-services through code weight control.

Temperature dependence is one of the main challenges of the silicon-on-insulator platform due to the large thermo-optic coefficient of its core material. In this work we propose a design of an all-passive athermal silicon-on-insulator Mach-Zehnder interferometer (MZI) based on the standard silicon material platform. The MZI's temperature compensation is achieved by optimizing the relative length of the wire and subwavelength grating arms and by tailoring the thermal response of the subwavelength structure. Simulations of the device performance showed that an overall temperature sensitivity of 7.5 pm/K could be achieved over a 100 nm spectral range near the 1550 nm region.

Particle swarm optimization (PSO) is a swarm-based optimization technique capable of solving different categories of optimization problems. Nevertheless, PSO has a serious exploration issue that makes it a difficult choice for multi-objectives constrained optimization problems (MCOP). At the same time, Multi-Protocol Label Switched (MPLS) and its extended version Generalized MPLS, has become an emerging network technology for modern and diverse applications. Therefore, as per MPLS and Generalized MPLS MCOP needs, it is important to find the Pareto based optimal solutions that guarantee the optimal resource utilization without compromising the quality of services (QoS) within the networks. The paper proposes a novel version of PSO, which includes a modified version of the Elitist learning Strategy (ELS) in PSO that not only solves the existing exploration problem in PSO, but also produces optimal solutions with efficient convergence rates for different MPLS/ GMPLS network scales. The proposed approach has also been applied with two objective functions; the resource provisioning and the traffic load balancing costs. Our simulations and comparative study showed improved results of the proposed algorithm over the well-known optimization algorithms such as standard PSO, Adaptive PSO, Bat and Dolphin algorithm.

The growing demand for extensive and reliable structural health monitoring resulted in the development of advanced optical sensing systems (OSS) that in conjunction with wireless optical networks (WON) are capable of extending the reach of optical sensing to places where fibre provision is not feasible. To support this effort, the paper proposes a new type of a variable weight code called multiweight zero cross-correlation (MW-ZCC) code for its application in wireless optical networks based optical code division multiple access (WON-OCDMA). The code provides improved quality of service (QoS) and better support for simultaneous transmission of video surveillance, comms and sensor data by reducing the impact of multiple access interference (MAI). The MW-ZCC code’s power of two code-weight properties provide enhanced support for the needed service differentiation provisioning. The performance of this novel code has been studied by simulations. This investigation revealed that for a minimum allowable bit error rate of 10−3, 10−9 and 10−12 when supporting triple-play services (sensing, datacomms and video surveillance, respectively), the proposed WON-OCDMA using MW-ZCC codes could support up to 32 simultaneous services over transmission distances up to 32 km in the presence of moderate atmospheric turbulence.

Polarization mode dispersion is recognized as a key factor limiting optical transmission systems, particularly those fiber links that run at bit rates beyond 10 Gbps. In-line test and characterization of polarization mode dispersion are thus of critical importance to evaluate the quality of installed optical fibers that are in use for high-speed signal traffics. However, polarization-based effects in optical fibers are stochastic and quite sensitive to a range of environmental changes, including optical cable movements. This, in turn, gives rise to undesired variations in light polarization that adversely impair the quality of the signal transmission in the link. In this work, we elaborate on experimental testing and theoretical analysis to asses changes of polarization mode dispersion in optical fibers that are caused by environmental variations, here wind gusts in particular. The study was performed on commercially harnessed optical fibers installed within optical power ground wire cables, taking into account different weather conditions. More specifically, we showed that changes caused by wind gusts significantly influence the differential group delay and the principal state of polarization in those optical fibers. For this, we experimentally measured a number of parameters to characterize light polarization properties. Measurements were carried out on C-band operated fiber-optic link formed by 111-km-long power ground wire cables and 88 spectral channels, with a test time step of 1 min during 12 consecutive days. Variations in differential group delay allowed for sensitive testing of environmental changes with measured maxims up to 10 ps under the worst wind conditions. Moreover, measured parameters were used in a numerical model to assess the quality of transmitted high-bit-rate optical signals as a function of wind conditions. The analysis revealed a negligible impact of wind on a 10 Gbps transmission, while substantial influence was noticed for higher bit rates up to 100 Gbps. These results show promises for efficient sensing of environmental changes and subsequent monitoring of the quality of recently used fiber-optic link infrastructures.

In many areas of the world accessing professional physicians “when needed/as needed” might not be always possible for a variety of reasons. Therefore, in such cases, a targeted e-Health solution to safeguard patient long-term health could be a meaningful approach. Today's modern healthcare technologies, often built around electronic and computer-based equipment, require an access to a reliable electricity supply. Many healthcare technologies and products also presume access to the high speed internet is available, making them unsuitable for use in areas where there is no fixed-line internet connectivity, access is slow, unreliable, and expensive, yet where the most benefit to patients may be gained. In this paper, a full mobile sensor platform is presented, based around readily-purchased consumer components, to facilitate a low cost and efficient means of monitoring the health of patients with prosthetic lower limbs. This platform is designed such that it can also be operated in a standalone mode, i.e., in the absence of internet connectivity, thereby making it suitable to the developing world. Also, to counter the challenge of power supply issues in e-Health monitoring, a self-contained rechargeable solution to the platform is proposed and demonstrated. The platform works with an Android mobile device, in order to allow for the capture of data from a wireless sensor unit, and to give the clinician access to results from the sensors. The results from the analysis, carried out within the platform's Raspberry Pi Zero, are demonstrated to be of use for remote monitoring. This is specifically targeted for monitoring the tissue health of lower limb amputees. The monitoring of residual limb temperature and gait can be a useful indicator of tissue viability in lower limb amputees especially those suffering from diabetes. We describe a route wherein non-invasive monitoring of tissue health is achievable using the Gaussian process technique. This knowledge will be useful in establishing biomarkers related to a possible deterioration in a patient's health or for assessing the impact of clinical interventions.

This paper investigates for the first time how the implementation of semiconductor optical amplifier (SOA)-based devices in photonic networks can negatively impact the integrity of two-dimensional wavelength-hopping time-spreading (2D-WH/TS) optical code-division multiple access (OCDMA) codes based on multi-wavelength picosecond code carriers. It is demonstrated and confirmed by simulations that the influence of an SOA under driving currents of 50 mA to 250 mA causes a 0.08 to 0.8 nm multi-wavelength picosecond code carriers’ wavelength redshift. The results obtained are then used to calculate the degradation of OCDMA system performance in terms of the probability of error Pe and the decrease in the number of simultaneous users. It is shown that, when the SOA-induced 0.8 nm code carriers redshift becomes equal to the code carries wavelength channel spacing, the (8,53)-OCDMA system performs only as a (7,53)-OCDMA system, and the number of simultaneous users drops from 14 to 10 or 84 to 74 with the forward error correction (FEC) Pe of 10−9, respectively. The impact of the 0.8 nm redshift is then shown on a (4,53)-OCDMA system, where it causes a drop in the number of simultaneous users from 4 to 3 or 37 to 24 with the FEC Pe of 10−9, respectively.

The nonlinear optical loop mirror (NOLM) has been studied for several decades and has attracted considerable attention for applications in high data rate optical communications and all-optical signal processing. The majority of NOLM research has focused on silica fiber-based implementations. While various fiber designs have been considered to increase the nonlinearity and manage dispersion, several meters to hundreds of meters of fiber are still required. On the other hand, there is increasing interest in developing photonic integrated circuits for realizing signal processing functions. In this paper, we realize the first-ever passive integrated NOLM in silicon photonics and demonstrate its application for all-optical signal processing. In particular, we show wavelength conversion of 10 Gb/s return-to-zero on-off keying (RZ-OOK) signals over a wavelength range of 30 nm with error-free operation and a power penalty of less than 2.5 dB, we achieve error-free nonreturn to zero (NRZ)-to-RZ modulation format conversion at 10 Gb/s also with a power penalty of less than 2.8 dB, and we obtain error-free all-optical time-division demultiplexing of a 40 Gb/s RZ-OOK data signal into its 10 Gb/s tributary channels with a maximum power penalty of 3.5 dB.

In light of the rapidly increasing demand for ultra-high speed data transmission, data centres are under pressure to provide ever increasing data transmission through their networks and at the same time improve the quality of data handling in terms of reduced latency, increased scalability and improved channel speed for users. However as data rates increase, present electronic switching technology using current data centre architecture is becoming increasingly difficult to scale despite improvements in data management. In this paper the tremendous bandwidth potential of optical fibre based networks will be explored alongside the issues of electronic scalability and switching speed. A resulting need for alternative optical solutions for all-optical signal processing systems will be discussed. With this in mind, progress in the form of a novel and highly scalable optical interconnect will be reviewed.

Chromatic and temperature induced dispersion can both severely affect incoherent high data rate communications in optical fibre. This is certainly also true for incoherent optical code division multiple access (OCDMA) systems with multi-wavelength picosecond code carriers. Here, even a relatively small deviation from a fully dispersion compensated transmission link can strongly impact the overall system performance, the number of simultaneous users, and the system cardinality due to the recovered OCDMA auto-correlation being strongly distorted, time-skewed, and having its full width at half maximum (FWHM) value changed. It is therefore imperative to have a simple tunable means for controlling fibre chromatic or temperature induced dispersion with high sub-picosecond accuracy. To help address this issue, we have investigated experimentally and by simulations the use of a semiconductor optical amplifier (SOA) for its ability to control the chirp of the passing optical signal (OCDMA codes) and to exploit the SOA ability for dispersion management of a fibre link in an incoherent OCDMA system. Our investigation is done using a 19.5 km long fibre transmission link that is exposed to different temperatures (20 °C and 50 °C) using an environmental chamber. By placing the SOA on a transmission site and using it to manipulate the code carrier’s chirp via SOA bias adjustments, we have shown that this approach can successfully control the overall fibre link dispersion, and it can also mitigate the impact on the received OCDMA auto-correlation and its FWHM. The experimental data obtained are in a very good agreement with our simulation results.