Search

Luminescent solar concentrators (LSCs) harness light generated by luminophores embedded in a light-trapping waveguide to concentrate onto smaller cells. LSCs can absorb both direct and diffuse sunlight, and thus can operate as flat plate receivers at a fixed tilt and with a conventional module form factor. However, current LSCs experience significant power loss through parasitic luminophore absorption and incomplete light trapping by the optical waveguide. Here, we introduce a tandem LSC device architecture that overcomes both of these limitations, consisting of a poly(lauryl methacrylate) polymer layer with embedded cadmium selenide core, cadmium sulfide shell (CdSe/CdS) quantum dot (QD) luminophores and an InGaP microcell array, which serves as high bandgap absorbers on the top of a conventional Si photovoltaic. We investigate the design space for a tandem LSC, using experimentally measured performance parameters for key components, including the InGaP microcell array, CdSe/CdS QDs, and spectrally selective waveguide filters. Using a Monte Carlo ray-tracing model, we compute the power conversion efficiency for a tandem LSC module with these components to be 29.4% under partially diffuse illumination conditions. These results indicate that a tandem LSC-on-Si architecture could significantly improve upon the efficiency of a conventional Si photovoltaic cell.

The aim of this study was to investigate the morphological traits and fragrance-related volatile compounds in three garden rose cultivars from the 'Fragrant Frayla' collection: 'Draga Frayla', 'Jelena Frayla', and 'Lenka Frayla', bred by the private breeding company Pheno Geno Roses. The roses were cultivated under open-field conditions in Temerin, Serbia, without irrigation and chemical treatments. Vegetative and generative properties were assessed in June and September 2023, while headspace volatile extraction and gas chromatography–mass spectrometry (GC-MS) were employed to identify scent-related volatiles. All three cultivars exhibited high ornamental value, with shrub heights ranging from 47 to 67 cm, semi-upright to upright growth habits, double flowers with diameters from 6.6 to 8.2 cm, and petal counts from 35.8 to 83.8. Upon sensory evaluations, 'Draga Frayla', 'Jelena Frayla', and 'Lenka Frayla' were characterized by moderately strong, strong and moderate fragrances, respectively. Volatile analysis detected the presence of phenylethyl alcohol (up to 57.31% in 'Draga Frayla'), terpenoids (a total of 28.2% for citronellol, geraniol, and nerol, found exclusively in 'Jelena Frayla'), and hydrocarbons. Hydrocarbons containing fewer than 30 C-atoms were predominantly found in 'Draga Frayla' (accounting for approximately 25% of the total peak area), while those with more than 30 C-atoms were present at less than 20% in the strongly scented roses. The highest number of volatiles was detected in 'Jelena Frayla', the rose cultivar identified as the most fragrant. The results revealed a correlation between strong fragrance intensity and elevated levels of phenylethyl alcohol and alcoholic monoterpenes, whereas a diverse array of hydrocarbons, rather than their concentration, appeared to enhance scent emission.

The several decades long rescue excavations of the ancient city of Viminacium have brought to light a large number of finds with very varied functions. In this paper, we will focus our attention on the remains of agricultural tools. They can be grouped according to their application: tools for clearing plants and preparing the soil for cultivation, tools used for tillage, implements for shredding and preparation for planting, as well as those used for mowing, harvesting, soil cleaning, and haymaking. The finds of agricultural tools that we present in this paper, although small in number, represent the most reliable indicators of agricultural activities in the period from the 2nd to the beginning of the 4th century, when Viminacium went through its period of greatest prosperity.

The paper presents the results of floristic composition and weed biomass in organic alfalfa crop in different years of alfalfa growing. The experiment was conducted in experimental plots in Futog, during the vegetation period of 2015. The presence of 60 weed species was noted, 49 of all weeds were noticed in the third, 48 in the fourth and 34 in the fifth year of organic alfalfa growing. Quantitative and qualitative structure of weed community depended on the age of alfalfa crop. By the analysis of cover values and the degree of the presence of weed species, it can be seen that species: Rumex obtusifolius L., Taraxacum officinale Web., Cynodon dactylon Pers. and Artemisia vulgaris L. had the greatest significance on weed infestation of alfalfa. The largest number of weed species belonged to the families Poaceae and Asteraceae. The biological spectrum of weeds species was defined by the terophyta dominance, whose number was reduced due to the age of the crop, while the share of hemicryptophytes and geophytes was more or less constant. Although we found a considerable level of infestation of alfalfa, alfalfa biomass reached acceptable values that were significantly higher than the weed biomass, which was statistically highly significant.

This paper presents the results on the presence of weeds in organic alfalfa crops in different years of growing, in Futog during the vegetation period in 2015. In the studied plots, 19 weed species were identified in the organic alfalfa crops, ranging from 13 in three-year-old crops to 17 in those in the fourth year of exploitation, with only 8 recorded in the five-year-old samples. Quantitative and qualitative weed community composition in the studied plots was dependent on the alfalfa crop maturity. It was found that there were statistically significant differences between the total infestation of alfalfa in different years crop utilization. Species Taraxacum officinale Web., Cynodon dactylon Pers. and Artemisia vulgaris L. had the greatest number and their number of individuals/m2 was statistically significantly higher than in all other identified species.

How to determine economic production runs (EPR) for multiple products in flexible manufacturing systems (FMS) is considered in this paper. Eight different although similar, models are developed and presented. The first four models are devoted to the cases when no shortage is allowed. The other four models are some kind of generalization of the previous ones when shortages may exist. The numerical examples are given as the illustration of the proposed models.

This paper discusses early Christian baptistries in the territory of northern Illyricum, which are dated to the period from the 4th to the beginning of the 7th century. The analysis of architectural shapes, positions and decorative elements makes it possible to define the basic types of baptistries, and their chronological attribution. The results of the analysis provides insight into the local specifics of the rite of baptism itself. Likewise, an attempt has been made to reconstruct the liturgical procedures that accompanied it.

We report the design of a tunable, narrowband, thermal metasurface that employs a hybrid resonance generated by coupling a tunable permittivity graphene ribbon to a silicon photonic crystal. The gated graphene ribbon array, proximitized to a high quality factor Si photonic crystal supporting a guided mode resonance, exhibits tunable narrowband absorbance lineshapes (Q > 10,000). Actively tuned Fermi level modulation in graphene with applied gate voltage between high absorptivity and low absorptivity states gives rise to absorbance on/off ratios exceeding 60. We employ coupled-mode theory as a computationally efficient approach to elements of the metasurface design, demonstrating an orders of magnitude speedup over typical finite element computational methods.

Optically Mie-resonant crystalline silicon nanoparticles have long attracted interest for their unique scattering behaviors. Here, we report a bottom-up nonthermal plasma process that produces highly monodisperse particles, with diameters controllable between 60 and 214 nm, by temporarily electrostatically trapping nanoparticles inside a continuous-flow plasma reactor. The particle size is tuned by adjusting the gas residence time in the reactor. By dispersing the nanoparticles in water, optical extinction measurements indicate colloidal solutions of a particle-based metafluid in which particles support both strong magnetic and electric dipole resonances at visible wavelengths. The spectral overlap of the electric and magnetic resonances gives rise to directional Kerker scattering. The extinction measurements show excellent agreement with Mie theory, supporting the idea that the fabrication process enables particles with narrow distributions in size, shape, and composition. This single-step gas-phase process can also produce Mie-resonant nanoparticles of dielectric materials other than silicon and directly deposit them on the desired substrates.

Waves impart momentum and exert force on obstacles in their path. The transfer of wave momentum is a fundamental mechanism for contactless manipulation, yet the rules of conventional scattering intrinsically limit the radiation force based on the shape and the size of the manipulated object. Here, we show that this intrinsic limit can be broken for acoustic waves with subwavelength-structured surfaces (metasurfaces), where the force becomes controllable by the arrangement of surface features, independent of the object's overall shape and size. Harnessing such anomalous metasurface scattering, we demonstrate complex actuation phenomena: self-guidance, where a metasurface object is autonomously guided by an acoustic wave, and tractor beaming, where a metasurface object is pulled by the wave. Our results show that bringing the metasurface physics of acoustic waves, and its full arsenal of tools, to the domain of mechanical manipulation opens new frontiers in contactless actuation and enables diverse actuation mechanisms that are beyond the limits of traditional wave-matter interactions., (© 2022. The Author(s).)

Optically induced magnetic resonances (OMRs) are highly tunable scattering states that cannot be reproduced in systems that only support electric resonances, such as in metals, lossy, or low-index materials. Despite offering unique scattering and coupling behavior, the study of OMRs in thin films has been limited by synthesis and simulation constraints. We report on the absorption and scattering response of OMR-based thin films composed of monodisperse crystalline silicon nanoparticles synthesized using a scalable nonthermal plasma growth technique and tractable simulation framework. The synthesis is solvent and ligand free, ensuring minimal contamination, and crystalline particles form with high yield and a narrow size distribution at close to room temperature. Using a scalable high-throughput deposition method, we deposit random particle films, without the need of a solid host matrix, showing near complete blackbody absorption at the collective OMR. This is achieved using 70% less material than an optimized antireflective-coated crystalline silicon thin film. The film exhibits strongly directional forward scattering with very low reflectivity, thus giving rise to angle- and polarization-insensitive antireflection properties across the visible spectrum. We find that, while commonly used effective medium models cannot capture the optical response, a modified effective medium accounting for multipole resonances and interparticle coupling shows excellent agreement with experiment. The effective permittivity and permeability are written in a mode and cluster resolved form, providing useful insight into how individual resonances and nanoparticle clusters affect the overall film response. Electric and magnetic-mode coupling show dramatically different behavior, resulting in uniquely different spectral broadening.

Solar steam water purification and fog collection are two independent processes that could enable abundant fresh water generation. We developed a hydrogel membrane that contains hierarchical three-dimensional microstructures with high surface area that combines both functions and serves as an all-day fresh water harvester. At night, the hydrogel membrane efficiently captures fog droplets and directionally transports them to a storage vessel. During the daytime, it acts as an interfacial solar steam generator and achieves a high evaporation rate of 3.64 kg m -2 h -1 under 1 sun enabled by improved thermal/vapor flow management. With a homemade rooftop water harvesting system, this hydrogel membrane can produce fresh water with a daily yield of ~34 L m -2 in an outdoor test, which demonstrates its potential for global water scarcity relief.

Light sails propelled by radiation pressure from high-power lasers have the potential to achieve relativistic spaceflight. In order to propel a spacecraft to relativistic speeds, an ultrathin, gram-sized light sail will need to be stably accelerated by lasers with ∼MW/cm 2 intensities operating in the near-infrared spectral range. Such a laser-driven sail requires multiband electromagnetic functionality: it must simultaneously exhibit very low absorptivity in the (Doppler-broadened) laser beam spectrum in the near-infrared and high emissivity in the mid-infrared for efficient radiative cooling. These engineering challenges present an opportunity for nanophotonic design. Here, we show that designed thin-film heterostructures could become multifunctional building-block elements of the light sail, due to their ability to achieve substantial reflectivity while maintaining low absorption in the near-infrared, significant emissivity in the mid-infrared, and a very low mass. For a light sail carrying a payload, we propose a relevant figure of merit-the reflectivity adjusted area density-that can capture the trade-off between sail mass and reflectivity, independent of other quantities such as the incident beam power, phased array size, or the payload mass. Furthermore, we present designs for effective thermal management via radiative cooling and compare propulsion efficiencies for several candidate materials, using a general approach that could apply to a broad range of high-power laser propulsion problems.

We theoretically demonstrate a near-field radiative thermal switch based on thermally excited surface plasmons in graphene resonators. The high tunability of graphene enables substantial modulation of near-field radiative heat transfer, which, when combined with the use of resonant structures, overcomes the intrinsically broadband nature of thermal radiation. In canonical geometries, we use nonlinear optimization to show that stacked graphene sheets offer improved heat conductance contrast between "ON" and "OFF" switching states and that a >10× higher modulation is achieved between isolated graphene resonators than for parallel graphene sheets. In all cases, we find that carrier mobility is a crucial parameter for the performance of a radiative thermal switch. Furthermore, we derive shape-agnostic analytical approximations for the resonant heat transfer that provide general scaling laws and allow for direct comparison between different resonator geometries dominated by a single mode. The presented scheme is relevant for active thermal management and energy harvesting as well as probing excited-state dynamics at the nanoscale.

Two-dimensional (2D) materials provide a platform for strong light-matter interactions, creating wide-ranging design opportunities via new-material discoveries and new methods for geometrical structuring. We derive general upper bounds to the strength of such light-matter interactions, given only the optical conductivity of the material, including spatial nonlocality, and otherwise independent of shape and configuration. Our material figure-of-merit shows that highly doped graphene is an optimal material at infrared frequencies, whereas single-atomic-layer silver is optimal in the visible. For quantities ranging from absorption and scattering to near-field spontaneous-emission enhancements and radiative heat transfer, we consider canonical geometrical structures and show that in certain cases the bounds can be approached, while in others there may be significant opportunity for design improvement. The bounds can encourage systematic improvements in the design of ultrathin broadband absorbers, 2D antennas, and near-field energy harvesters.

Shaping the topology of light, by way of spin or orbital angular momentum engineering, is a powerful tool to manipulate matter on the nanoscale. Conventionally, such methods focus on shaping the incident beam of light and not the full interaction between the light and the object to be manipulated. We theoretically show that tailoring the topology of the phase space of the light particle interaction is a fundamentally more versatile approach, enabling dynamics that may not be achievable by shaping of the light alone. In this manner, we find that optically asymmetric (Janus) particles can become stable nanoscale motors even in a light field with zero angular momentum. These precessing steady states arise from topologically protected anticrossing behavior of the vortices of the optical torque vector field. Furthermore, by varying the wavelength of the incident light, we can control the number, orientations, and the stability of the spinning states. These results show that the combination of phase-space topology and particle asymmetry can provide a powerful degree of freedom in designing nanoparticles for optimal external manipulation in a range of nano-optomechanical applications.

In solar cells, the mismatch between the Sun's emission spectrum and the cells' absorption profile limits the efficiency of such devices, while in incandescent light bulbs, most of the energy is lost as heat. One way to avoid the waste of a large fraction of the radiation emitted from hot objects is to tailor the thermal emission spectrum according to the desired application. This strategy has been successfully applied to photonic-crystal emitters at moderate temperatures, but is exceedingly difficult for hot emitters (>1,000 K). Here, we show that a plain incandescent tungsten filament (3,000 K) surrounded by a cold-side nanophotonic interference system optimized to reflect infrared light and transmit visible light for a wide range of angles could become a light source that reaches luminous efficiencies (∼40%) surpassing existing lighting technologies, and nearing a limit for lighting applications. We experimentally demonstrate a proof-of-principle incandescent emitter with efficiency approaching that of commercial fluorescent or light-emitting diode bulbs, but with exceptional reproduction of colours and scalable power. The ability to tailor the emission spectrum of high-temperature sources may find applications in thermophotovoltaic energy conversion and lighting.

Theoretical accounts as well as behavioral studies reporting animacy effects offer inconsistent and sometimes contradictory results. A possible explanation for these inconsistencies may be inadvertent biases in the stimuli selected for test - with category-specific effects driven by characteristics of test stimuli other than animacy per se. In this study, we pit animacy against feature structure (intra-item variability), in a picture-word matching task. For unimpaired adults, regardless of whether objects were from animate (mammals; insects) or inanimate (clothes; musical instruments) superordinate categories, participants were faster to match basic level labels with objects from categories with low intra-item variability (mammals; clothes) than from categories with high intra-item variability (insects; instruments). Thus, pitting animacy against variability allowed us to clarify that observable differences in processing speed between animals and instruments are systematically driven by the intra-item variability of the superordinate categories, and not by animacy itself.

Purpose: This article reports findings from an evaluation of reach and engagement of The FaceSpace Project, a novel sexual health promotion project delivered through social networking sites that targeted young people aged 16-29 years., Methods: Multiple methods were used to evaluate project reach and engagement. The evaluation focussed on quantitative data (online usage statistics, online surveys), complemented by available qualitative data (project team meeting notes)., Results: The project reached 900 fans who were mostly between 18 and 34 years of age. The most successful ways of increasing audience reach were via Facebook advertisements and tagging photos of young people attending a music festival on the project Facebook page. Peaks in Facebook page interactions (comments and "likes") coincided with recruitment peaks and when videos were posted. However, video views varied greatly between postings. Feedback from the project team for increasing engagement in future social networking site interventions included having one centralized Facebook page and using episodic videos., Conclusions: This evaluation is among the first to assess the use of social networking sites for sexual health promotion and provides information to inform the implementation and evaluation of future projects using new media. Social networking sites offer great potential to reach and engage young people for sexual health promotion. However, further work is required to improve implementation and promote audience reach and engagement as well as to determine effectiveness of social networking sites in changing knowledge, attitudes, and behaviors., (Copyright © 2013 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.)

Background: A growing number of health promotion interventions are taking advantage of the popularity and interactivity of new social media platforms to foster and engage communities for health promotion. However, few health promotion interventions using social networking sites (SNS) have been rigorously evaluated. "Queer as F**k"(QAF) began as pilot project in 2010 to deliver sexual health promotion via short "webisodes" on SNS to gay men. Now in its fifth season, QAF is among the few published examples internationally to demonstrate the sexual health promotion potential of SNS., Objective: The objective of this evaluation is to assess reach, interactivity, and engagement generated by QAF to inform future health interventions and evaluations using SNS., Methods: We undertook a mixed method process evaluation using an uncontrolled longitudinal study design that compared multiple measurements over time to assess changes in reach and engagement. We adapted evaluation methods from the health promotion, information systems, and creative spheres. We incorporated online usage statistics, interviews informed by user diary-scrapbooks, and user focus groups to assess intervention reach and engagement., Results: During Series 1-3 (April 2010 to April 2011), 32 webisodes were posted on the QAF Facebook and YouTube pages. These webisodes attracted over 30,000 views; ranging from 124-3092 views per individual episode. By April 2011, the QAF Facebook page had 2929 predominantly male fans. Interview and focus group participants supported the balance of education and entertainment. They endorsed the narrative "soap opera" format as an effective way to deliver sexual health messages in an engaging, informative, and accessible manner that encouraged online peer discussion of sexual health and promoted community engagement., Conclusions: QAF offers a successful example of exploiting the reach, interactivity, and engagement potential of SNS; findings from this process evaluation provide a model to inform the delivery and evaluation of future health promotion interventions on SNS.

Near-field thermophotovoltaic (TPV) systems with carefully tailored emitter-PV properties show large promise for a new temperature range (600 – 1200K) solid state energy conversion, where conventional thermoelectric (TE) devices cannot operate due to high temperatures and far-field TPV schemes suffer from low efficiency and power density. We present a detailed theoretical study of several different implementations of thermal emitters using plasmonic materials and graphene. We find that optimal improvements over the black body limit are achieved for low bandgap semiconductors and properly matched plasmonic frequencies. For a pure plasmonic emitter, theoretically predicted generated power density of 14 W/cm2 and efficiency of 36% can be achieved at 600K (hot-side), for 0.17eV bandgap (InSb). Developing insightful approximations, we argue that large plasmonic losses can, contrary to intuition, be helpful in enhancing the overall near-field transfer. We discuss and quantify the properties of an optimal near-field photovoltaic (PV) diode. In addition, we study plasmons in graphene and show that doping can be used to tune the plasmonic dispersion relation to match the PV cell bangap. In case of graphene, theoretically predicted generated power density of 6(120) W/cm2 and efficiency of 35(40)% can be achieved at 600(1200)K, for 0.17eV bandgap. With the ability to operate in intermediate temperature range, as well as high efficiency and power density, near-field TPV systems have the potential to complement conventional TE and TPV solid state heat-to-electricity conversion devices.

Online social networking sites offer a novel setting for the delivery of health promotion interventions due to their potential to reach a large population and the possibility for two-way engagement. However, few have attempted to host interventions on these sites, or to use the range of interactive functions available to enhance the delivery of health-related messages. This paper presents lessons learnt from "The FaceSpace Project", a sexual health promotion intervention using social networking sites targeting two key at-risk groups. Based on our experience, we make recommendations for developing and implementing health promotion interventions on these sites. Elements crucial for developing interventions include establishing a multidisciplinary team, allowing adequate time for obtaining approvals, securing sufficient resources for building and maintaining an online presence, and developing an integrated process and impact evaluation framework. With two-way interaction an important and novel feature of health promotion interventions in this medium, we also present strategies trialled to generate interest and engagement in our intervention. Social networking sites are now an established part of the online environment; our experience in developing and implementing a health promotion intervention using this medium are of direct relevance and utility for all health organizations creating a presence in this new environment.

We demonstrate the possibility of achieving enhanced frequency-selective near-field radiative heat transfer between patterned (photonic-crystal) slabs at designable frequencies and separations, exploiting a general numerical approach for computing heat transfer in arbitrary geometries and materials based on the finite-difference time-domain method. Our simulations reveal a tradeoff between selectivity and near-field enhancement as the slab-slab separation decreases, with the patterned heat transfer eventually reducing to the unpatterned result multiplied by a fill factor (described by a standard proximity approximation). We also find that heat transfer can be further enhanced at selective frequencies when the slabs are brought into a glide-symmetric configuration, a consequence of the degeneracies associated with the nonsymmorphic symmetry group.