Search

The effects of abiotic and biotic parameters on the occurrence of Antarctic krill (Euphausia superba) concentrations have been examined in waters north of the South Shetland Islands. Krill density rose from early to mid-summer, but density was low in the oceanic zone, and higher in the slope frontal zone.surface water circulation in areas of krill concentrations was sluggish, enhancing the residence time. Krill appear highly adapted to exploit the rich food resources of the frontal/inshore zone.

When in contact with charged solid surfaces, ionic liquids (ILs) are known to form solvation structures consisting of alternating cation and anion layers. This phenomenon is considered to originate from the adsorption layer of counterions overcompensating the surface charge, so-called overscreening. However, the response of these layers to surfaces with near-zero or extremely high surface charge density (σ) remains inadequately understood. Here, we probe the solvation structure of ILs on alkali halide surfaces with varied surface orientations: nearly zero-charged RbI(100) and highly charged RbI(111), by employing frequency modulation atomic force microscopy with atomic resolution. Two commonly used ILs are examined in this study: 1-methyl-1-propylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([C 3 mpyr][NTf 2 ]) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C 2 mim][NTf 2 ]). On RbI(100) surfaces with near zero σ, we observe alternating cation and anion layers, diverging from the previously proposed monolayer model for IL/alkali halide(100) interfaces. These results support the argument that overscreening occurs under low σ, even approaching zero, and reconcile conflicting experimental conclusions about low σ systems. On RbI(111) surfaces with high σ, we identify solvation structures consisting of two consecutive counterion layers. This structure aligns with the theoretically predicted crowding; a phenomenon rarely observed in commonly used ILs due to typically unreachable σ in electrochemical IL/electrode systems. Our findings indicate that alkali halide(111) surfaces are potentially valuable for exploring the crowding phenomenon in ILs, addressing the current scarcity of experimental observations.

Interaction between two bodies in a liquid metal is an important topic for development of metallic products with high performance. We conducted atomic force microscopy measurements and achieved the interaction between the substrate and the probe in liquid Ga of an opaque and highly viscous liquid. The interaction cannot be accessed with the normal atomic force microscopy, electron microscopy, and beam reflectometry. We performed a theoretical calculation using statistical mechanics of simple liquids by mixing an experimentally derived quantum effect. From both experiment and theory, we found an unusual behaviour in the interaction between the solvophobic substances, which has never been reported in water and ionic liquids. Shapes of the interaction curves between several solvophobic and solvophilic pairs in liquid Ga are also studied., Competing Interests: There are no conflicts of interest to declare., (This journal is © The Royal Society of Chemistry.)

The detection of vertical and lateral forces at the nanoscale by atomic force microscopy (AFM) reveals various mechanical properties on surfaces. The qPlus sensor is a widely used force sensor, which is built from a quartz tuning fork (QTF) and a sharpened metal probe, capable of high-resolution imaging in viscous liquids such as lubricant oils. Although a simultaneous detection technique of vertical and lateral forces by using a qPlus sensor is required in the field of nanotribology, it has still been difficult because the torsional oscillations of QTFs cannot be detected. In this paper, we propose a method to simultaneously detect vertical and lateral force components by using a qPlus sensor with a long probe. The first three eigenmodes of the qPlus sensor with a long probe are theoretically studied by solving a set of equations of motion for the QTF prong and probe. The calculation results were in good agreement with the experimental results. It was found that the tip oscillates laterally in the second and third modes. Finally, we performed friction anisotropy measurements on a polymer film by using a bimodal AFM utilizing the qPlus sensor with a long probe to confirm the lateral force detection., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

In this report, micropatterns of (3-aminopropyl)trimethoxysilane (APTMS) were developed on hydrophilic and hydrophobic surfaces after patterning using 172 nm vacuum ultraviolet (VUV) photolithography. Self-assembled monolayers (SAMs) formed on Si substrates through UV hydrosilylation of 1-hexadecene (HD) and 10-undecenoic acid (UDA) were used as hydrophilic and hydrophobic surfaces, respectively. For templating the HD- and UDA-SAMs, the VUV light was exposed to HD- and UDA-SAMs from the slits of photomasks in atmospheric and evacuated environments, respectively. Various oxygenated groups were generated at the exposed domains of HD-SAM, while the COOH groups were trimmed from the irradiated domains of UDA-SAM. The APTMS molecules were immobilized on the domains that were terminated by oxygenated groups after chemical vapor deposition (CVD). The thicknesses of the developed APTMS micropatterns increased significantly by raising the CVD temperature and in the presence of ambient air in the CVD Teflon container as well. The increase in thicknesses was ascribed to the formation of APTMS multilayers, which were mediated by H 3 N + ions. Also, the developed APTMS micropatterns on the UDA-SAM patterned by VUV light irradiation in a high-vacuum environment (HV-VUV) were thicker than those on the VUV/(O) patterned HD-SAM due to the presence of inactive oxygenated groups at the surface of VUV/(O)-terminated domains of HD-SAM such as COO-C and C-O-C groups. The presence of water or ambient air facilitated the silane coupling between the silyl groups with the oxygenated and amino groups The combination of VUV photolithography and the CVD method with control of the conditions would enable us to control the thicknesses and shapes of the developed APTMS micropatterns. These findings illustrate the applicability of VUV photolithography for templating hydrophobic and hydrophobic surfaces toward the development of organosilane architectures, which can be feasible for several applications.

Chemical etching of silicon assisted by various types of carbon materials is drawing much attention for the fabrication of silicon micro/nanostructures. We developed a method of chemical etching of silicon that utilizes graphene oxide (GO) sheets to promote the etching reaction in a hydrofluoric acid-nitric acid (HF-HNO 3 ) etchant. By using an optimized composition of the HF-HNO 3 etchant, the etching rate under the GO sheets was 100 times faster than that of our HF-H 2 O 2 system used in a previous report. Kinetic analyses showed that the activation energy of the etching reaction was almost the same at both the bare silicon and GO-covered areas. We propose that adsorption sites for the reactant in the GO sheets enhance the reaction frequency, leading to a deeper etching in the GO areas than the bare areas. Furthermore, GO sheets with more defects were found to have higher catalytic activities. This suggests that defects in the GO sheets function as adsorption sites for the reactant, thereby enhancing the etching rate under the sheets.

Microcontact printing (μCP) techniques have sparked a surge of interests in microfabrication since they help produce arrays on a wide range of target substrates in a facile and efficient manner. Polydimethylsiloxane (PDMS), as a well-established material for stamps, has constraints resulting from its hydrophobicity and softness, and the replication of PDMS stamps usually requires rigid masters or processes using a photoresist. Herein, a novel μCP stamp based on cyclo-olefin polymer (COP) is produced through vacuum ultraviolet (VUV) lithography. 2,4,6,8-Tetramethylcyclotetrasiloxane is selectively deposited at the affinity-patterns on the COP surface, and these patterned siloxane films are converted into SiO x meanwhile protecting the COP beneath them from the VUV photoetching. By this means, a patterned relief is fabricated on the COP plates, resulting in a hydrophilic SiO x /COP μCP stamp with punch heights of ∼180 nm. The novelty arises from the simplicity of the master- and photoresist-free microstructuring, and the higher stiffness of SiO x /COP stamps prevents the deformation during pressing. Finally, an example μCP is given to transfer titania precursor gel and produce TiO 2 micropatterns on flexible polymer substrates. The SiO x /COP stamps and the μCP of TiO 2 provide simple and cost-effective patterning techniques, which should contribute to the future design and creation of flexible devices.

Fundamental understanding of the confinement of water in porous coordination polymers (PCPs) is important not only with respect to their application, such as in gas storage and separation, but also for exploring confinement effects in nanoscale spaces. Here, we report the observation of water in an exotic state in the well-designed hydrophilic nanopores of PCPs. Single-crystal X-ray diffraction finds that nanoconfined water has an ordered structure that is characteristic in ices, but infrared spectroscopy reveals a significant number of broken hydrogen bonds that is characteristic in liquids. We find that their structural properties are quite similar to those of solid-liquid supercritical water predicted in hydrophobic nanospace at extremely high pressure. Our results will open up not only new potential applications of water in an exotic state in PCPs to control chemical reactions, but also experimental systems to clarify the existence of solid-liquid critical points., (© 2020. The Author(s).)

Formation of precise and high-resolution silica micropatterns on polymer substrates is of importance in surface structuring for flexible device fabrication of optics, microelectronic, and biotechnology. To achieve that, substrates modified with affinity-patterns serve as a strategy for site-selective deposition. In the present paper, vacuum ultraviolet (VUV) treatment is utilized to achieve spatially-controlled surface functionalization on a cyclo-olefin polymer (COP) substrate. An organosilane, 2,4,6,8-tetramethylcyclotetrasiloxane (TMCTS), preferentially deposits on the functionalized regions. Well-defined patterns of TMCTS are formed with a minimum feature of ∼500 nm. The secondary VUV/(O)-treatment converts TMCTS into SiO x , meanwhile etches the bare COP surface, forming patterned SiO x /COP microstructures with an average height of ∼150 nm. The resulting SiO x patterns retain a good copy of TMCTS patterns, which are also consistent with the patterns of photomask used in polymer affinity-patterning. The high quality SiO x patterns are of interests in microdevice fabrication, and the hydrophilicity contrast and adjustable heights reveal their potential application as a "stamp" for microcontact printing (μCP) techniques., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

This work describes the UV alkoxylation of a series of 1,2-epoxyalkanes on the hydrogen-terminated silicon (H-Si) substrate. The formation of alkoxy self-assembled monolayers (SAMs) and the nature of bonding at the surface of H-Si were examined using water contact angle goniometer, spectroscopic ellipsometer, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy. UV exposure to 1,2-epoxyalkane mesitylene solution for 60 min formed alkoxy-SAMs onto H-Si with hydrophobic properties. The local molecular environment of the alkyl chains transitioned from a disordered, liquid-like state to an ordered, crystalline-like structure with increasing the chain length. XPS and FTIR indicated that the reaction of H-Si with 1,2-epoxyalkane produced Si-O-C linkages. The Si-H bond homolysis and electron/hole were the plausible mechanistic routes for the grafting of 1,2-epoxyalkanes.

Automation is a useful strategy to make laborious evolutionary experiments faster and easier. To date, several types of continuous flow reactors have been developed for the automated evolutionary experiments of viruses and bacteria. However, the development of a flow reactor applicable to compartmentalized in vitro self-replication systems is still a challenge. In this study, we demonstrate automated in vitro evolution of a translation-coupled RNA system in a droplet flow reactor for the first time. This reactor contains approximately 10 10 micro-scale droplets (average diameter is approximately 0.8 μm), which continuously fuse and divide among each other at a controllable rate. In the droplets, an RNA (artificial genomic RNA) replicate through the translation of self-encoded RNA replicase with spontaneously appearing parasitic RNA. We performed two automated replication experiments for more than 400 hours with different mixing intensities. We found that several mutations displayed increased frequencies in the genomic RNA populations and the dominant RNA mutants acquired the ability to replicate faster or acquired resistance to the parasitic RNA, demonstrating that Darwinian evolution occurred during the long-term replication. The droplet flow reactor we developed can be a useful tool to perform in vitro evolutionary experiments of translation-coupled systems.

We have prepared COOH- and COOCH 3 -terminated self-assembled monolayers (SAMs) from undec-10-enoic acid (UDA) and methyl undec-10-enoate (MUDO) molecules on hydrogen-terminated silicon (H-Si) substrates through ultraviolet (UV) irradiation. The as-prepared UDA- and MUDO-SAMs were exposed to 172 nm vacuum-UV (VUV) light in a high vacuum environment (HV, <10 -3 Pa) for different periods. The presence of COO components at the surfaces of these SAMs without prior oxidation would simplify the understanding of the origin of the chemical conversions and the changes of surface properties, as the prior oxidation would change the surface properties and generate different oxygenated groups. After the HV-VUV treatment, the abundance of COOH and COOCH 3 components of these SAMs decreased without significant dissociation of their C-C backbones. Degradation of these components occurred through dissociating their C-O bonds, resulting in different C═O components. Also, the occurrence of Norrish type pathways resulted in a slight decrease of carbon content and produced CH 3 components. We have applied the HV-VUV lithography to control the abundance of COOH and COOCH 3 components in well-defined areas and to investigate the friction differences between the irradiated and masked areas. The irradiated areas exhibited lower friction than the masked areas without observing significant height contrasts between these areas. The reduction in friction was attributed to the conversion of the COOH and COOCH 3 components to less adhesive components such as C═O and CH 3 . These experiments suggest the HV-VUV treatments as an approach for low damage dry surface modifications and reductive lithographic techniques at surfaces terminated by acid and ester groups.