Search

Digital PCR (dPCR) is a powerful method for highly sensitive and precise quantification of nucleic acids. However, designing and optimizing new multiplex dPCR assays using target sequence specific probes remains cumbersome, since fluorescent signals must be optimized for every new target panel. As a solution, we established a generic fluorogenic 6-plex reporter set, based on mediator probe technology, that decouples target detection from signal generation. This generic reporter set is compatible with different target panels and thus provides already optimized fluorescence signals from the start of new assay development. Generic reporters showed high population separability in a colorimetric 6-plex mediator probe dPCR, due to their tailored fluorophore and quencher selection. These reporters were further tested using different KRAS, NRAS and BRAF single-nucleotide polymorphisms (SNP), which are frequent point mutation targets in liquid biopsy. We specifically quantified SNP targets in our multiplex approach down to 0.4 copies per microliter (cp/µL) reaction mix, equaling 10 copies per reaction, on a wild-type background of 400 cp/µL for each, equaling 0.1% variant allele frequencies. We also demonstrated the design of an alternative generic reporter set from scratch in order to give detailed step-by-step guidance on how to systematically establish and optimize novel generic reporter sets. Those generic reporter sets can be customized for various digital PCR platforms or target panels with different degrees of multiplexing. [ABSTRACT FROM AUTHOR]

This document is a letter published in the journal Clinical Chemistry & Laboratory Medicine. It discusses a clinical pilot study on the automation of library preparation for next-generation sequencing (NGS) using microfluidics. The study focuses on the screening of somatic rearrangements of Immunoglobulin (IG) genes in patients with acute lymphoblastic leukemia (ALL). The researchers used a centrifugal microfluidic cartridge and a modified commercially available player for the automation process. The results showed that the automated library preparation using microfluidics was comparable to manual library preparation in terms of coverage and detection of IGH-VJ rearrangements. The study suggests that centrifugal microfluidic automation can reduce complexity and staff hands-on time in a clinical setup for library preparation. However, the choice of automation system depends on the throughput numbers of the laboratory. The researchers also mention the possibility of manufacturing cartridges for other lymphoid malignancies and the potential for MRD quantification by NGS. [Extracted from the article]

LiCoO2 electrodes contain three phases, or domains, each having specific-intended functions: ion-conducting pore space, lithium-ion-reacting active material, and electron conducting carbon-binder domain (CBD). Transport processes take place in all domains on different characteristic length scales: from the micrometer scale in the active material grains through to the nanopores in the carbon-binder phase. Consequently, more than one imaging approach must be utilized to obtain a hierarchical geometric representation of the electrode. An approach incorporating information from the micro- and nanoscale to calculate 3D transport-relevant properties in a large-reconstructed active domain is presented. Advantages of focused ion beam/scanning electron microscopy imaging and X-ray tomography combined by a spatial stochastic model, validated with an artificially produced reference structure are used. This novel approach leads to significantly different transport relevant properties compared with previous tomographic approaches: nanoporosity of the CBD leads to up to 42% additional contact area between active material and pore space and increases ionic conduction by a factor of up to 3.6. The results show that nanoporosity within the CBD cannot be neglected. [ABSTRACT FROM AUTHOR]

X-ray tomography allows the active-material domain (LiCoO2) of Li-ion battery cathodes to be imaged, but it is unable to resolve the carbon-binder domain (CBD). Here, a new method for creating a complete 3D representation (virtual design) of all three phases of a cathode is provided; this includes the active-material domain, the CBD, and the electrolyte-filled pore space. It combines X-ray tomographic data of active material with a statistically modeled CBD. Two different statistical CBD morphology models are compared as examples: i) a random cluster model representing a standard mixture of carbon black and polyvenylidene fluoride (PVDF) and ii) a fiber model. The transport parameters are compared in a charged and a discharged cathode. The results demonstrate that the CBD content and morphology changes the ionic and electronic transport parameters dramatically and thus cannot be neglected. Calculations yield that the fiber model shows up to three times higher electrical conductivity at the same CBD content (discharged case) and better ionic diffusion conditions for all CBD contents. In the charged case, the morphology impact on electrical conduction is small. This effective method to generate transport parameters for different CBDs can be transferred to other CBD morphologies and electrodes. [ABSTRACT FROM AUTHOR]