Search

The long-term success of root canal treatment requires the prevention of bacterial leakage between canal walls and root canal obturation. In this study, we compared the leakage of Enterococcus faecalis in thirty single-rooted mandibular premolars divided into three groups. The roots in two experimental groups were obturated using a single-cone obturation technique with two different bio-ceramic sealers (MTA Fillapex and CeraSeal) while the roots in the conventional group were obturated using the lateral condensation technique with an epoxy resin sealer (AH Plus). A bacterial leakage test was carried out using a modified microbial leakage model. In the MTA Fillapex group, 30% of the specimens showed a positive sign for bacterial leakage, while 80% of samples in the CeraSeal group leaked. In the AH Plus group, 50% of specimens had bacterial leakage in the canals. The variation of the average number of days between the groups was not found to be significantly different. Taken together, bio-ceramic sealers with single-cone obturation demonstrated comparable results to the resin-based sealer with lateral condensation technique in terms of sealing efficiency against Enterococcus faecalis. Additionally, MTA Fillapex could provide a better sealing ability than CeraSeal bio-ceramic sealer.

Poly(methyl methacrylate) (PMMA) is a commonly used material, as it is biocompatible and relatively cheap. However, its mechanical properties and weak antibiofilm activity are major concerns. With the development of new technology, 3D-printed resins are emerging as replacements for PMMA. Few studies have investigated the antibiofilm activity of 3D-printed resins. Therefore, this study aimed to investigate the antibiofilm activity and surface roughness of a 3D-printed denture base resin modified with different concentrations of zirconium dioxide nanoparticles (ZrO2 NPs). A total of 60 resin disc specimens (15 × 2 mm) were fabricated and divided into six groups (n = 10). The groups comprised a heat-polymerized resin (PMMA) group, an unmodified 3D-printed resin (NextDent) group, and four 3D-printed resin groups that were modified with ZrO2 NPs at various concentrations (0.5 wt%, 1 wt%, 3 wt%, and 5 wt%). All specimens were polished using a conventional method and then placed in a thermocycler machine for 5000 cycles. Surface roughness (Ra, µm) was measured using a non-contact profilometer. The adhesion of Candida albicans (C. albicans) was measured using a fungal adhesion assay that consisted of a colony forming unit assay and a cell proliferation assay. The data were analyzed using Shapiro–Wilk and Kruskal–Wallis tests. A Mann–Whitney U test was used for pairwise comparison, and p-values of less than 0.05 were considered statistically significant. The lowest Ra value (0.88 ± 0.087 µm) was recorded for the PMMA group. In comparison to the PMMA group, the 3% ZrO2 NPs 3D-printed group showed a significant increase in Ra (p < 0.025). For the 3D-printed resins, significant differences were found between the groups with 0% vs. 3% ZrO2 NPs and 3% vs. 5% ZrO2 NPs (p < 0.025). The highest Ra value (0.96 ± 0.06 µm) was recorded for the 3% ZrO2 NPs group, and the lowest Ra values (0.91 ± 0.03 µm) were recorded for the 0.5% and 5% ZrO2 NPs groups. In terms of antifungal activity, the cell proliferation assay showed a significant decrease in the C. albicans count for the 0.5% ZrO2 NPs group when compared with PMMA and all other groups of 3D-printed resins. The group with the lowest concentration of ZrO2 NPs (0.5%) showed the lowest level of C. albicans adhesion of all the tested groups and showed the lowest Candida count (0.29 ± 0.03). The addition of ZrO2 NPs in low concentrations did not affect the surface roughness of the 3D-printed resins. These 3D-printed resins with low concentrations of nanocomposites could be used as possible materials for the prevention and treatment of denture stomatitis, due to their antibiofilm activities.