Search

This article describes waffle power MOSFET segmentation and defines its analytic models. Although waffle gate pattern is well-known architecture for effective channel scaling without requirements on process modification, no until today precise model considering segmentation of MOSFETs with waffle gate patterns, due to bulk connections, has been there proposed. Two different MOSFET topologies with gate waffle patterns have been investigated and compared with the same on-resistance of a standard MOSFET with finger gate pattern. The first one with diagonal metal interconnections allows reaching more than 40 % area reduction. The second MOSFET with the more simple orthogonal metal interconnections allows saving more than 20 % area. Moreover, new models defining conditions where segmented power MOSFETs with waffle gate patterns occupy less area than the standard MOSFET with finger gate pattern, have been introduced.

A true random number generator (TRNG) with time multiplexed metastability-based sources of randomness, presented in this paper, is capable of generating random bit sequences formed from noise present in the electronic circuit. An incorporated time multiplexer interleaves digitized random signals coming from sources of randomness and increases output data rate. The proposed TRNGwas fabricated in a STMicroelectronics 130 nm bulk CMOS technology on an area of 0.029mm2. The quality of all random bit sequences has been verified by the FIPS and NIST statistical test suites. The fabricated TRNG generates random bit sequences up to the data rate of 20 Mb/s without any corrective mechanisms at power consumption of 72.48 uW. The changing environmental conditions do not influence the quality of random bit sequences.

This paper discusses the characterization and evaluation of an MEMS based electrostatic generator, a part of the power supply unit of the self-powered microsystem[1,2,3]. The designed generator is based on electrostatic converter and uses the principle of conversion of non-electric energy into electrical energy by periodical modification of gap between electrodes of a capacitor [4]. The structure is designed and modeled as three-dimensional silicon based MEMS. Innovative approach involving the achievement of very low resonant frequency of the structure (about 100Hz) by usage of modified long cantilever spring design, minimum area of the chip, 3D work mode, the ability to be tuned to reach desired parameters, proves promising directions of possible further development.

This paper discusses the design of an electrostatic generator, power supply component of the self-powered microsystem, which is able to provide enough energy to power smart sensor chains or if necessary also other electronic monitoring devices. One of the requirements for this analyzer is the mobility, so designing the power supply expects use of an alternative way of getting electricity to power the device, rather than rely on periodic supply of external energy in the form of charging batteries, etc. In this case the most suitable method to use is so-called energy harvesting – a way how to gather energy. This uses the principle of non-electric conversion of energy into electrical energy in the form of converters. The present study describes the topology design of such structures of electrostatic generator. Structure is designed and modeled as a three-dimensional silicon based MEMS. Innovative approach involving the achievement of very low resonant frequency of the structure, while the minimum area of the chip, the ability to work in all 3 axes of coordinate system and ability to be tuned to reach desired parameters proves promising directions of possible further development of this issue. The work includes simulation of electro-mechanical and electrical properties of the structure, description of its behavior in different operating modes and phases of activity. Simulation results were compared with measured values of the produced prototype chip. These results can suggest possible modifications to the proposed structure for further optimization and application environment adaptation.

The paper presents solution for wireless and battery-less measurement in the enclosed areas. The principle is based on passive RFID, nevertheless this paper is focused on high power-demanding applications such as MEMS accelerometers, gas sensors, piezoresistive strain gauges, etc. Standard FRID communication scheme (sensing the input current change on the primary side) cannot be used in this case, because the communication channel is overloaded by the high power load. Paper presents possible solution which is based on the dual frequency scheme – one frequency for powering and other for the communication. This is ensuring capability for measurement up to several centimeters on the frequency bands 125 kHz and 375 kHz. It can be suitable for continual measurement in isolated systems such as the rotating objects, concrete walls, enclosed plastic barrels, high temperature chambers etc.

Thermal and thermo-mechanical modeling and characterization of solid state lightening (SSL) retrofit LED lamp are presented in this paper. Paramount importance is to design SSL lamps for reliability, in which thermal and thermo-mechanical aspects are key points. The main goal is to get a precise 3D thermal lamp model for further thermal optimization. Simulations are performed with ANSYS and CoventorWare software tools to compere different simulation approaches. Simulated thermal distribution has been validated with thermal measurement on a commercial 8W LED lamp. Materials parametric study has been carried out to discover problematic parts for heat transfer from power LEDs to ambient and future solutions are proposed. The objectives are to predict the thermal management by simulation of LED lamp, get more understanding in the effect of lamp shape and used materials in order to design more effective LED lamps and predict light quality, life time and reliability.