Search

Objective: This work aims to determine whether photoacoustic (PA) thermometry from a commercially available PA imaging system can be used to control the temperature in nanoparticle-mediated thermal therapies. Methods: The PA imaging system was interfaced to obtain PA images while scanning ex-vivo tissue. These images were then used to obtain temperature maps in real-time during heating. Validation and calibration of the PA thermometry were done using a fluoroptic thermometer. This thermometer was also used to develop and tune a software-based proportional integral derivative (PID) controller. Finally, a PA-based PID closed-loop controller was used to control gold nanorod (GNR) mediated laser therapy. Results: The use of GNRs substantially enhanced laser heating; the temperature rise increased 7-fold by injecting a GNR solution with a concentration of 0.029 mg/mL. The control experiments showed that the desired temperature could be achieved and maintained at a targeted location in the ex-vivo tissue. The steady-state mean absolute deviations (MAD) from the targeted temperature during control were between 0.16 $^\circ {\kern-0.70007pt}\text{C}$ and 0.5 $^\circ {\kern-0.70007pt}\text{C}$ , depending on the experiment. Conclusion: It was possible to control hyperthermia treatments using a software-based PID controller and a commercial PA imaging system. Significance: The monitoring and control of the temperature in thermal-based therapies are important for assuring a prescribed temperature to the target tissue while minimizing the temperature of the surrounding healthy tissue. This easily implemented non-invasive control system will facilitate the realization of a broad range of hyperthermia treatments.

A real-time and non-invasive thermometry method is crucial for thermal therapies to monitor and control the treatment. Ultrasound can be used as an attractive thermometry modality for its relatively high sensitivity to change in temperature and fast data collection and processing abilities. In this work, an ultrasound thermometry method based on the change in backscattered energy (CBE) is used to control the tissue temperature using a closed-loop controller in real-time. A clinical high-frequency ultrasound scanner was used to acquire RF echo data from ex vivo porcine tissue samples while the tissue was being exposed to an interstitial laser heating source. The control system was used to rapidly increase the temperature from 37°C (baseline temperature) to 43 °C (target temperature) and maintain the target temperature for about 6 minutes. The results show that the ultrasound thermometry based on CBE generated by a high-frequency ultrasound scanner can be used to generate 2D temperature maps of a localized heating region in the hyperthermia temperature range (∼43°C). The estimated temperature varied by an average of ±0.8 °C compared to a calibrated fiber-optic measurement. Thus, a non-invasive ultrasound thermometry method based on the CBE technique can be used for real-time monitoring and control of hyperthermia treatments, using the interstitial laser heating source with acceptable accuracy.

Purpose A real-time and non-invasive thermometry technique is essential in thermal therapies to monitor and control the treatment. Ultrasound is an attractive thermometry modality due to its relatively high sensitivity to change in temperature and fast data acquisition and processing capabilities. A temperature-sensitive acoustic parameter is required for ultrasound thermometry in order to track the changes in that parameter during the treatment. Currently, the main ultrasound thermometry methods are based on variation in the attenuation coefficient, the change in backscattered energy of the signal (CBE), the backscattered radio-frequency (RF) echo-shift due to change in the speed of sound and thermal expansion of the medium, and change in the amplitudes of the acoustic harmonics. In this work, an ultrasound thermometry method based on second harmonic CBE (CBEh2) and combined fundamental and second harmonic CBE (CBEcomb) is used to produce 2D temperature maps, detect localized heated region generated by low intensity focused ultrasound (LIFU), and control temperature in the heated region. Materials and methods Ex vivo pork muscle tissue samples were exposed to localized LIFU heating source and 2D temperature maps were produced from the RF data acquired by a 4.2 MHz linear array probe using a Verasonics Vantage™ ultrasound scanner (Verasonics Inc., Redmond, WA) after the exposure. Calibrated needle thermocouples were also placed in the ex vivo tissue sample close to the LIFU focal zone for temperature calibration purposes. The estimated temperature maps were the established echo-shift technique. A tissue motion compensation algorithm was also used to reduce the susceptibility to motion artifacts. Results 2D temperature maps were generated using CBE of acoustic harmonic and echo-shift techniques. The results show a direct correlation between the CBE of acoustic harmonics and focal tissue temperature for a range of temperatures from 37 °C (baseline) to 47 °C. Conclusions The findings of this study show that the CBE of acoustic harmonics technique can be used to noninvasively estimate temperature change in tissue in the hyperthermia temperature range.

In this work, the influence of colors of filters upon the photovoltaic panels rising temperature and electrical performance was studied under Baghdad Meteorological Condition. Basing on the energy analysis of a photovoltaic solar system and by using the photonic theory, the available energy on the PV plane system has been evaluated. Seven colored filters each with (85W) PV modules were used in this case study, to reveal the impact of colored filters upon the electrical productivity of PV panel with the variation in the temperature caused by these filters. There is the main issue of this work is to show how the performance of PV module by imposing colored filter and hence how and to how much improve it by reducing the cell temperature in hot climate. Outcomes showed that the PV technology is affected by the color filters. In other words, red filter gives light have least photons energy, and violet filter gives light have the most photons energy and green is between the two. So, red colors filter gives highest PV panel temperature comparative with others filters, while violet color filter was the lowest. PV module with the lowest temperature colored filter gives the best electrical performance than others.

Influence of combined square nozzle with helical tape inserted in a constant heat flux tube on heat transfer enhancement for turbulent airflow for Reynolds number ranging from 7000 to 14500 were investigated experimentally. Three different pitch ratios for square nozzle (PR = 5.8, 7.7 and 11.6) according to three different numbers of square nozzle (N = 3, 4 and 5) and constant pitch ratios for helical tape were used. The results observed that the Nusselt number and friction factor for combination with winglets were found to be up to 33.8 % and 21.4 %, respectively higher than nozzle alone for pitch ratio PR=5.8. The maximum value of thermal performance for using combination with winglets was about 1.351 for pitch ratio= 5.8. Nusselt number and friction factor correlations from experimental data were developed for turbulent flow.

In present study, the effect of combining single-slope solar still unit with high-frequency ultrasonic vaporizer, PCM capsules, and external solar water heater on improving its performance was experimentally investigated. A single-slop solar still was developed and examined under the harsh climate of Baghdad city in middle Iraq territory. Compared with the conventional solar still, the results indicated that using PCM cylindrical capsules increases the water productivity of the still about 30.6%. High water productivity was achieved by using an external solar water heater and high-frequency ultrasonic vaporizer was about 415% respectively. Results also illustrate that increasing the operation time of ultrasonic vaporizer has a negative effect on water productivity and thermal efficiency. The maximum thermal efficiency reached 39.3% for the modified solar still with ultrasonic vaporizer with 30 min operation time, while its value is reported to be about 34.2% for 60 min operation time. According to the economic analysis, such units are reliable in remote regions with an estimated cost equal 0.037 and 0.028 $/L for conventional and modified solar still with ultrasonic vaporizer respectively.

Heat exchangers are widely used in many industrial applications. It is well known that the effectiveness of these exchangers is normally measured by the amount of the heat transfer, which should be minimized as much as possible according to their size. Present study pays more attention to examine Taylor vortex which formed in the flow of the hot water of the smooth surface heat exchanger and a swirl flow of cold air. Also, an attempt was made to improve the result by replacing the heat transfer surface by Nanoaluminume metal. Experimental results revealed that the effectiveness of the exchanger at the ratio (Cmin/Cmax = 0.08) could be enhanced the effectiveness of the standard exchanger at the ratio (Cmin/Cmax = 0). Further, it was found that using nano Aluminume as a medium material for heat transfer increased the effectiveness (3.2%, 4.3% and 4.58%) for a rotational speed of inner cylinder which were used (0, 65and 80) rpm, respectively.

A new second-order formulation is obtained for elastic wave propagation in 2D media bounded by a perfectly matched layer (PML). The formulation uses a complex coordinate stretching approach with a two-parameter stretch function. The final system, consisting of just two second-order displacement equations along with four auxiliary equations, is smaller than existing formulations, thereby simplifying the problem and reducing the computational cost. With the help of a plane-wave analysis, the stability of the continuous formulation is examined. It is shown that by increasing the scaling parameter in the stretch function, any existing instability is moved to higher spatial frequencies. Since discrete models cannot resolve frequencies beyond a certain limit, this can lead to significant computational stability improvements. Numerical results are shown to validate our formulation and to illustrate the improved stability that can be achieved with certain anisotropic media that have known issues.

Photoacoustic (PA) signals encode information about the optical absorption and spatial distribution of absorbing chromophores as well as the light distribution in the medium. The wavelength dependence of the latter affects the accuracy in chromophore quantification, including estimations of oxygen saturation (sO2) with depth. We propose the use of the ratio of the PA radiofrequency (RF) spectral slopes (SS) at different optical wavelengths to generate frequency filters which can be used to match the fluence profiles across separate images generated with different optical wavelengths. Proof-of-principle experiments were carried on a plastic tube with blood of a known oxygenation inserted into a porcine tissue. The algorithm was tested in-vivo in the hind leg of six CD1 mice, each under three different breathing conditions (100 % O2, room air and 100 % CO2). Imaging was done using the VevoLAZR system at the wavelengths 720 and 870 nm. The SS was calculated from the linear fit of the ratio of the photoacoustic RF power spectra at the two wavelengths. An ultrasound frequency filter was designed and applied to each segmented PA signal in the frequency domain and inversely transformed into the time domain to correct for the differences in the fluence profiles at both wavelengths. Linear spectral unmixing was used to estimate sO2 before and after applying the ultrasound frequency filter. The estimated blood sO2 in the plastic tube for the porcine tissue experiment improved by 10.3% after applying the frequency filter when compared to the sO2 measured by a blood gas analyzer. For the in-vivo mouse experiments, the applied sO2 correction was 2.67, 1.33 and -3.33% for every mm of muscle tissue for mice breathing 100% O2, room air and 100% CO2, respectively. The approach presented here provides a new approach for fluence matching that can potentially improve the accuracy of sO2 estimates by removing the fluence depth dependence at different optical wavelengths.

This paper proposes a new numerical framework to simulate ultrasound wave propagation in 3D viscoelastic heterogeneous media based on the elastodynamic wave equation including a 3D second-order time-domain perfectly matched layer formulation. A finite difference discretization of this formulation is presented, along with a stability analysis. The resulting model is capable of simulating 3D shear and longitudinal acoustic waves for arbitrary source geometries and excitations, together with arbitrary initial and boundary conditions. A simulation example is provided to show the application of our proposed method for tissue elastography imaging. Specifically, the propagation of shear waves from a localized lesion to the surrounding normal tissue is examined.

Wave propagation in an infinite medium can be numerically simulated by surrounding a finite region by a perfectly matched layer (PML). When the medium is heterogeneous consisting of both solids and liquids, careful consideration is needed in specifying the properties of the PML especially because parts of it lie at the solid-fluid interface. While such a situation could arise in many important fields including marine seismology, where water is in contact with earth, and in biomedical ultrasound, where soft tissue is in contact with bone, no PML formulation exists to appropriately model such coupled problems. Here, a second-order time-domain PML formulation for fluid-solid heterogeneous media in two dimensions that satisfies the interface coupling boundary condition throughout the computational domain is presented. Numerical results are given to establish the applicability and accuracy of such a PML formulation in discrete settings without causing stability issues, spurious reflections, or any other problems. In particular, the effectiveness of the PML in absorbing all kinds of bulk waves, as well as surface and evanescent waves, is studied.

The International Photoacoustic Standardisation Consortium (IPASC) emerged from SPIE 2018, established to drive consensus on photoacoustic system testing. As photoacoustic imaging (PAI) matures from research laboratories into clinical trials, it is essential to establish best-practice guidelines for photoacoustic image acquisition, analysis and reporting, and a standardised approach for technical system validation. The primary goal of the IPASC is to create widely accepted phantoms for testing preclinical and clinical PAI systems. To achieve this, the IPASC has formed five working groups (WGs). The first and second WGs have defined optical and acoustic properties, suitable materials, and configurations of photoacoustic image quality phantoms. These phantoms consist of a bulk material embedded with targets to enable quantitative assessment of image quality characteristics including resolution and sensitivity across depth. The third WG has recorded details such as illumination and detection configurations of PAI instruments available within the consortium, leading to proposals for system-specific phantom geometries. This PAI system inventory was also used by WG4 in identifying approaches to data collection and sharing. Finally, WG5 investigated means for phantom fabrication, material characterisation and PAI of phantoms. Following a pilot multi-centre phantom imaging study within the consortium, the IPASC settled on an internationally agreed set of standardised recommendations and imaging procedures. This leads to advances in: (1) quantitative comparison of PAI data acquired with different data acquisition and analysis methods; (2) provision of a publicly available reference data set for testing new algorithms; and (3) technical validation of new and existing PAI devices across multiple centres.