Search

Intense ultrashort laser pulses with high temporal quality are essential for fundamental science. Nonlinear polarization ellipse rotation (NER) is one way to ensure this high temporal quality, by suppressing weaker signals beyond the duration of the main pulse up to a few orders of magnitude. Post-compression schemes have revolutionized ultrafast lasers, enabling the generation of pulses with durations beyond the limit supported by laser gain media. However, high compression ratios lead to the formation of new pre- and post-pulses. Both NER and post-compression depend on the optical Kerr effect. This makes the combination of the two in a single setup both advantageous and straightforward. While NER cannot suppress the new pre- and post-pulses generated in post-compression, we show via simulations and experimental data that by combining the two, it is possible to shape the output spectrum and counteract temporal contrast degradation.

We report the development of a robust Yb-doped fiber laser system based on chirped-pulse amplification (CPA), generating 44-fs laser pulses with up to 70-µJ pulse energy at a 1-MHz repetition rate. It consists of a Yb-doped nonlinear polarization evolution (NPE) mode-locked fiber oscillator, a chirped fiber Bragg grating (CFBG) stretcher, a wave-shaper for manipulating the spectrum of the signal, cascaded fiber amplifiers, and two compression units. The output pulse duration of 44 fs for efficient high harmonic generation (HHG) was achieved by a multi-pass multi-plate Herriott-type non-linear compression unit.

Ultrashort ultraviolet (UV) pulses are pivotal for resolving ultrafast electron dynamics. However, their efficient generation is strongly impeded by material dispersion and two-photon absorption, in particular, if pulse durations around a few tens of femtoseconds or below are targeted. Here, we present a new (to our knowledge) approach to ultrashort UV pulse generation: using the fourth-harmonic generation output of a commercial ytterbium laser system delivering 220 fs UV pulses, we implement a multi-pass cell (MPC) providing 5.6 µJ pulses at 256 nm, compressed to 30.5 fs. Our results set a short-wavelength record for MPC post-compression while offering attractive options to navigate the trade-off between upconversion efficiency and acceptance bandwidth for UV pulse production.

Advancing ultrafast high-repetition-rate lasers to shortest pulse durations comprising only a few optical cycles while pushing their energy into the multi-millijoule regime opens a route toward terawatt-class peak powers at unprecedented average power. We explore this route via efficient post-compression of high-energy 1.2 ps pulses from an ytterbium InnoSlab laser to 9.6 fs duration using gas-filled multi-pass cells (MPCs) at a repetition rate of 1 kHz. Employing dual-stage compression with a second MPC stage supporting a close-to-octave-spanning bandwidth enabled by dispersion-matched dielectric mirrors, a record compression factor of 125 is reached at 70% overall efficiency, delivering 6.7 mJ pulses with a peak power of ∼0.3 TW. Moreover, we show that post-compression can improve the temporal contrast at multi-picosecond delay by at least one order of magnitude. Our results demonstrate efficient conversion of multi-millijoule picosecond lasers to high-peak-power few-cycle sources, prospectively opening up new parameter regimes for laser plasma physics, high energy physics, biomedicine, and attosecond science.

Frequency combs present a unique tool for high-precision and rapid molecular spectroscopy. Difference frequency generation (DFG) of near-infrared sources is a common approach to generate passively stabilized mid-infrared combs. However, only little attention has been paid so far to precisely measure the coherence properties of such sources. Here, we investigate these using a Raman-soliton based DFG source driven by an Yb:fiber frequency comb. A heterodyne beat between the second harmonic of the phase-locked DFG comb near 4 µm and a 2 µm Tm:fiber frequency comb locked to the same optical reference is performed. Using this method, we measure the relative phase noise power spectral density of both combs. This results in a sub-Hz relative linewidth between the DFG comb and the Tm:fiber comb. We also introduce a new pump/seed delay locking mechanism based on interferometry for long-term stable intensity noise suppression.

The generation of below-threshold harmonics in gas-jets constitutes a promising path towards optical frequency combs in the vacuum ultra-violet (VUV) spectral range. Of particular interest is the 150 nm range, which can be exploited to probe the nuclear isomeric transition of the Thorium-229 isotope. Using widely available high-power, high-repetition-rate Ytterbium-based laser sources, VUV frequency combs can be generated through the process of below-threshold harmonic generation, in particular 7 th harmonic generation of 1030 nm. Knowledge about the achievable efficiencies of the harmonic generation process is crucial for the development of suitable VUV sources. In this work, we measure the total output pulse energies and conversion efficiencies of below-threshold harmonics in gas-jets in a phase-mismatched generation scheme using Argon and Krypton as nonlinear media. Using a 220 fs, 1030 nm source, we reach a maximum conversion efficiency of 1.1 × 10 -5 for the 7 th harmonic (147 nm) and 0.78 × 10 -4 for the 5 th harmonic (206 nm). In addition, we characterize the 3 rd harmonic of a 178 fs, 515 nm source with a maximum efficiency of 0.3%.

Post-compression methods for ultrafast laser pulses typically face challenging limitations, including saturation effects and temporal pulse breakup, when large compression factors and broad bandwidths are targeted. To overcome these limitations, we exploit direct dispersion control in a gas-filled multi-pass cell, enabling, for the first time to the best of our knowledge, single-stage post-compression of 150 fs pulses and up to 250 µJ pulse energy from an ytterbium (Yb) fiber laser down to sub-20 fs. Dispersion-engineered dielectric cavity mirrors are used to achieve nonlinear spectral broadening dominated by self-phase modulation over large compression factors and bandwidths at 98% throughput. Our method opens a route toward single-stage post-compression of Yb lasers into the few-cycle regime.

Few-cycle pulses present an essential tool to track ultrafast dynamics in matter and drive strong field effects. To address photon-hungry applications, high average power lasers are used which, however, cannot directly provide sub-100-fs pulse durations. Post-compression of laser pulses by spectral broadening and dispersion compensation is the most efficient method to overcome this limitation. We present a notably compact setup which turns a 0.1-GW peak power, picosecond burst-mode laser into a 2.9-GW peak power, 8.2-fs source. The 120-fold pulse duration shortening is accomplished in a two-stage hybrid multi-pass, multi-plate compression setup. To our knowledge, neither shorter pulses nor higher peak powers have been reported to-date from bulk multi-pass cells alone, manifesting the power of the hybrid approach. It puts, for instance, compact, cost-efficient, and high repetition rate attosecond sources within reach.

We demonstrate a 41.6 MHz, 1.3 ps, 140 pJ Ho:fiber oscillator using a nonlinear amplifying loop mirror (NALM) as saturable absorber. The oscillator is constructed entirely with polarization-maintaining (PM) fibers, is tunable with a center wavelength between 2035 nm and 2075 nm, and can be synchronized to an external RF reference. For our application of Ho:YLF amplifier seeding for dielectric electron acceleration, the laser is tuned to 2050 nm and synchronized to a stable RF reference with 45 fs rms timing jitter in the integration interval [10 Hz, 1 MHz]. We show long term synchronized operation and characterize the relative intensity noise (RIN) and timing jitter of the oscillator for two different Tm-fiber pump lasers.

We present the design, integration, and operation of the novel vacuum ultraviolet (VUV) beamline installed at the free-electron laser (FEL) FLASH. The VUV source is based on high-order harmonic generation (HHG) in gas and is driven by an optical laser system synchronized with the timing structure of the FEL. Ultrashort pulses in the spectral range from 10 to 40 eV are coupled with the FEL in the beamline FL26, which features a reaction microscope (REMI) permanent endstation for time-resolved studies of ultrafast dynamics in atomic and molecular targets. The connection of the high-pressure gas HHG source to the ultra-high vacuum FEL beamline requires a compact and reliable system, able to encounter the challenging vacuum requirements and coupling conditions. First commissioning results show the successful operation of the beamline, reaching a VUV focused beam size of about 20 µm at the REMI endstation. Proof-of-principle photo-electron momentum measurements in argon indicate the source capabilities for future two-color pump-probe experiments.

Nonlinear pulse post-compression represents an efficient method for ultrashort, high-quality laser pulse production. The temporal pulse quality is, however, limited by amplitude and phase modulations intrinsic to post-compression. We here characterize in frequency and time domain with high dynamic range individual post-compressed pulses within laser bursts comprising 100-kHz-rate pulse trains. We spectrally broaden 730 fs, 3.2 mJ pulses from a Yb:YAG laser in a gas-filled multi-pass cell and post-compress them to 56 fs. The pulses exhibit a nearly constant energy content of 78% in the main peak over the burst plateau, which is close to the theoretical limit. Our results demonstrate attractive pulse characteristics, making multi-pass post-compressed lasers very applicable for pump-probe spectroscopy at, e.g., free-electron lasers or as efficient drivers for secondary frequency conversion stages.

This paper reports on nonlinear spectral broadening of 1.1 ps pulses in a gas-filled multi-pass cell to generate sub-100 fs optical pulses at 1030 nm and 515 nm at pulse energies of 0.8 mJ and 225 µJ, respectively, for pump-probe experiments at the free-electron laser FLASH. Combining a 100 kHz Yb:YAG laser with 180 W in-burst average power and a post-compression platform enables reaching simultaneously high average powers and short pulse durations for high-repetition-rate FEL pump-probe experiments., (open access.)

We demonstrate a femtosecond enhancement cavity with a crossed-beam geometry for efficient generation and extraction of extreme-ultraviolet (XUV) frequency combs at a 154 MHz repetition rate. We achieve a record-high out-coupled power of 600  μW, directly usable for spectroscopy, at a wavelength of 97 nm. This corresponds to a >60% out-coupling efficiency. The XUV power scaling and generation efficiency are similar to that achieved with a single Gaussian-mode fundamental beam inside a collinear enhancement cavity. The noncollinear geometry also opens the door for the generation of isolated attosecond pulses at >100  MHz repetition rate.

We present a flexible all-polarization-maintaining (PM) mode-locked ytterbium (Yb):fiber laser based on a nonlinear amplifying loop mirror (NALM). In addition to providing detailed design considerations, we discuss the different operation regimes accessible by this versatile laser architecture and experimentally analyze five representative mode-locking states. These five states were obtained in a 78-MHz configuration at different intracavity group delay dispersion (GDD) values ranging from anomalous (-0.035 ps 2 ) to normal (+0.015 ps 2 ). We put a particular focus on the characterization of the intensity noise as well as the free-running linewidth of the carrier-envelope-offset (CEO) frequency as a function of the different operation regimes. We observe that operation points far from the spontaneous emission peak of Yb (∼1030 nm) and close to zero intracavity dispersion can be found, where the influence of pump noise is strongly suppressed. For such an operation point, we show that a CEO linewidth of less than 10-kHz at 1 s integration can be obtained without any active stabilization.

In this work, we demonstrate postcompression of 1.2 ps laser pulses to 13 fs via gas-based multipass spectral broadening. Our results yield a single-stage compression factor of about 40 at 200 W in-burst average power and a total compression factor >90 at reduced power. The employed scheme represents a route toward compact few-cycle sources driven by industrial-grade Yb:YAG lasers at high average power.

Ultrafast measurements in the extreme ultraviolet (XUV) spectral region targeting femtosecond timescales rely until today on two complementary XUV laser sources: free electron lasers (FELs) and high-harmonic generation (HHG) based sources. The combination of these two source types was until recently not realized. The complementary properties of both sources including broad bandwidth, high pulse energy, narrowband tunability and femtosecond timing, open new opportunities for two-color pump-probe studies. Here we show first results from the commissioning of a high-harmonic beamline that is fully synchronized with the free-electron laser FLASH, installed at beamline FL26 with permanent end-station including a reaction microscope (REMI). An optical parametric amplifier synchronized with the FEL burst mode drives the HHG process. First commissioning tests including electron momentum measurements using REMI, demonstrate long-term stability of the HHG source over more than 14 hours. This realization of the combination of these light sources will open new opportunities for time-resolved studies targeting different science cases including core-level ionization dynamics or the electron dynamics during the transformation of a molecule within a chemical reaction probed on femtosecond timescales in the ultraviolet to soft X-ray spectral region.

We demonstrate dual-comb generation from an all-polarization-maintaining dual-color ytterbium (Yb) fiber laser. Two pulse trains with center wavelengths at 1030 nm and 1060 nm respectively are generated within the same laser cavity with a repetition rate around 77 MHz. Dual-color operation is induced using a tunable mechanical spectral filter, which cuts the gain spectrum into two spectral regions that can be independently mode-locked. Spectral overlap of the two pulse trains is achieved outside the laser cavity by amplifying the 1030-nm pulses and broadening them in a nonlinear fiber. Spatially overlapping the two arms on a simple photodiode then generates a down-converted radio frequency comb. The difference in repetition rates between the two pulse trains and hence the line spacing of the down-converted comb can easily be tuned in this setup. This feature allows for a flexible adjustment of the tradeoff between non-aliasing bandwidth vs. measurement time in spectroscopy applications. Furthermore, we show that by fine-tuning the center-wavelengths of the two pulse trains, we are able to shift the down-converted frequency comb along the radio-frequency axis. The usability of this dual-comb setup is demonstrated by measuring the transmission of two different etalons while the laser is completely free-running.

We present the development of a gas nozzle providing high-density gas at elevated temperatures inside a vacuum environment. Fused silica is used as the nozzle material to allow the placement of the nozzle tip in close proximity to an intense, high-power laser beam, while minimizing the risk of sputtering nozzle tip material into the vacuum chamber. Elevating the gas temperature increases the gas-jet forward velocity, allowing us to replenish the gas volume in the laser-gas interaction region between consecutive laser shots. The nozzle accommodates a 50 μ m opening hole from which a supersonic gas jet emerges. Heater wires are used to bring the nozzle temperature up to 730 °C, while a cooling unit ensures that the nozzle mount and the glued nozzle-to-mount connection is kept at a temperature below 50 °C. The presented nozzle design is used for high-order harmonic generation in hot gases using gas backing pressures of up to 124 bars.

The sub-cycle dynamics of electrons driven by strong laser fields is central to the emerging field of attosecond science. We demonstrate how the dynamics can be probed through high-order harmonic generation, where different trajectories leading to the same harmonic order are initiated at different times, thereby probing different field strengths. We find large differences between the trajectories with respect to both their sensitivity to driving field ellipticity and resonant enhancement. To accurately describe the ellipticity dependence of the long trajectory harmonics we must include a sub-cycle change of the initial velocity distribution of the electron and its excursion time. The resonant enhancement is observed only for the long trajectory contribution of a particular harmonic when a window resonance in argon, which is off-resonant in the field-free case, is shifted into resonance due to a large dynamic Stark shift.

We generate high-order harmonics at high pulse repetition rates using a turnkey laser. High-order harmonics at 400 kHz are observed when argon is used as target gas. In neon, we achieve generation of photons with energies exceeding 90 eV (∼13 nm) at 20 kHz. We measure a photon flux of up to 4.4 × 10(10) photons per second per harmonic in argon at 100 kHz. Many experiments employing high-order harmonics would benefit from higher repetition rates, and the user-friendly operation opens up for applications of coherent extreme ultra-violet pulses in new research areas.

We study two-color high-order harmonic generation using an intense driving field and its weak second harmonic, crossed under a small angle in the focus. Employing sum- and difference-frequency generation processes, such a noncollinear scheme can be used to measure and control macroscopic phase matching effects by utilizing a geometrical phase mismatch component, which depends on the noncollinear angle. We further show how spatial phase effects in the generation volume are mapped out into the far field allowing a direct analogy with temporal carrier envelope effects in attosecond pulse generation.

We study the influence of the generation conditions on the group delay of attosecond pulses in high-order harmonic generation in gases. The group delay relative to the fundamental field is found to decrease with increasing gas pressure in the generation cell, reflecting a temporal walk-off due to the dispersive properties of the nonlinear medium. This effect is well reproduced using an on-axis phase-matching model of high-order harmonic generation in an absorbing gas.

We develop and implement an experimental strategy for the generation of high-energy high-order harmonics (HHG) in gases for studies of nonlinear processes in the soft x-ray region. We generate high-order harmonics by focusing a high energy Ti:Sapphire laser into a gas cell filled with argon or neon. The energy per pulse is optimized by an automated control of the multiple parameters that influence the generation process. This optimization procedure allows us to obtain energies per pulse and harmonic order as high as 200 nJ in argon and 20 nJ in neon, with good spatial properties, using a loose focusing geometry (f#≈400) and a 20 mm long medium. We also theoretically examine the macroscopic conditions for absorption-limited conversion efficiency and optimization of the HHG pulse energy for high-energy laser systems.

High-order harmonic generation (HHG) in gases has been established as an important technique for the generation of coherent extreme ultraviolet (XUV) pulses at ultrashort time scales. Its main drawback, however, is the low conversion efficiency, setting limits for many applications, such as ultrafast coherent imaging, nonlinear processes in the XUV range, or seeded free electron lasers. Here we introduce a novel scheme based on using below-threshold harmonics, generated in a "seeding cell", to boost the HHG process in a "generation cell", placed further downstream in the focused laser beam. By modifying the fundamental driving field, these low-order harmonics alter the ionization step of the nonlinear HHG process. Our dual-cell scheme enhances the conversion efficiency of HHG, opening the path for the realization of robust intense attosecond XUV sources.

We report on the fabrication and characterization of amplitude and phase samples consisting of well defined Au or Al features formed on ultrathin silicon nitride membranes. The samples were manufactured using electron beam lithography, metallization and a lift-off technique, which allow precise lateral control and thickness of the metal features. The fabricated specimens were evaluated by conventional microscopy, atomic force microscopy and with the digital in-line holography set-up at the Lund Laser Centre. The latter uses high-order harmonic generation as a light source, and is capable of recovering both the shape and phase shifting properties of the samples. We report on the details of the sample production and on the imaging tests with the holography set-up., (© 2012 The Authors Journal of Microscopy © 2012 Royal Microscopical Society.)

We investigate macroscopic interference effects in high-order harmonic generation using a Ti:sapphire laser operating at a 100 kHz repetition rate. The structure and behavior of spectral and spatial interference fringes are explained and analytically described by transient phase matching of the long electron trajectory contribution. Time-frequency mapping due to the temporal chirp of the harmonic emission allows us to observe Maker fringes directly in the spectral domain.