Search

The presence of impurities such as H2S, thiols, ketones, and permanent gases in propylene of fossil origin and their use in the polypropylene production process affect the efficiency of the synthesis and the mechanical properties of the polymer and generate millions of losses worldwide. This creates an urgent need to know the families of inhibitors and their concentration levels. This article uses ethylene green to synthesize an ethylene–propylene copolymer. It describes the impact of trace impurities of furan in ethylene green and how this furan influences the loss of properties such as thermal and mechanical properties of the random copolymer. For the development of the investigation, 12 runs were carried out, each in triplicate. The results show an evident influence of furan on the productivity of the Ziegler–Natta catalyst (ZN); productivity losses of 10, 20, and 41% were obtained for the copolymers synthesized with ethylene rich in 6, 12, and 25 ppm of furan, respectively. PP0 (without furan) did not present losses. Likewise, as the concentration of furan increased, it was observed that the melt flow index (MFI), thermal (TGA), and mechanical properties (tensile, bending, and impact) decreased significantly. Therefore, it can be affirmed that furan should be a substance to be controlled in the purification processes of green ethylene. © 2023 by the authors.

Industrial wastewater from petrochemical processes is an essential source of the synthetic phenolic phosphite antioxidant (Irgafos P-168), which negatively affects the environment. For the determination and analysis of Irgafos P-168, DSC, HPLC-MS, and FTIR methodologies were used. Solid phase extraction (SPE) proved to be the best technique for extracting Irgafos from wastewater. HPLC-MS and SPE determined the repeatability, reproducibility, and linearity of the method and the SPE of the standards and samples. The relative standard deviations, errors, and correlation coefficients for the repeatability and reproducibility of the calibration curves were less than 4.4% and 4.2% and greater than 0.99955, respectively. The analysis of variance (ANOVA), using the Fisher method with confidence in 95% of the data, did not reveal significant differences between the mentioned parameters. The removal of the antioxidant from the wastewater by SPE showed recovery percentages higher than 91.03%, and the chemical characterization of this antioxidant by FTIR spectroscopy, DSC, TGA, and MS showed it to be structurally the same as the Irgafos P-168 molecule. The recovered Irgafos was added to the polypropylene matrix, significantly improving its oxidation times. An OIT analysis, performed using DSC, showed that the recovered Irgafos-blended polypropylene (PP) demonstrated oxidative degradation at 8 min. With the addition of the Irgafos, the oxidation time was 13 min. This increases the polypropylene’s useful life and minimizes the environmental impact of the wastewater.

Currently, polypropylene (PP) is highlighted using sorbitol-based clarifying agents since these agents are high quality, low cost, and work as a barrier against moisture, which makes PP ideal for packaging food, beverages, and medical products, among others. The use of analytical methods capable of recovering these additives in wastewater streams and then reusing them in the PP clarification stage represents an innovative methodology that makes a substantial contribution to the circular economy of the PP production industry. In this study, a method of extraction and recovery of the Millad NX 8000 was developed. The additive was recovered using GC-MS and extracted with an activated carbon column plus glass fiber, using an injection molded sample, obtaining a recovery rate greater than 96%. TGA, DSC, and FTIR were used to evaluate the recovered additive’s glass transitions and purity. The thermal degradation of the recovered additive was found to be between 340 and 420 °C, with a melting temperature of 246 °C, adopting the same behavior as the pure additive. In FTIR, the characteristic absorption peak of Millad NX 8000 was observed at 1073 cm−1, which indicates the purity of the extracted compound. Therefore, this work develops a new additive recovery methodology with high purity to regulate the crystallization behavior and of PP. © 2023 by the authors.

Additives play an important role in the production of plastic materials through their application, in which the mechanical, thermal, and physical properties of polymers are improved, making them last longer and be more resistant. During the synthesis of polypropylene resins, the remains of additives that are not absorbed by the resin are removed in the purification stage and end up in the wastewater. In this article, the recovery of (Z)-13-docosenamide from the wastewater from the process, its purification, and its application in the process was carried out. For the extraction of the additive, solid phase extraction (SPE) was used, and to guarantee the purity of (Z)-13-docosenamide, techniques such as high performance liquid chromatography (HPLC), Fourier transform infrared (FTIR), gas chromatography-mass spectrometry (GC/MS), thermogravimetric (TG) coupled with a gas chromatography-mass spectrometry (GC/MS), and differential scanning calorimetry (DSC) were used. The recovered erucamide was added to the PP between 0.05 and 0.3% w/w. The effects of the properties of the virgin polypropylene with the recovered additive were also evaluated to determine its effectiveness in improving the properties of the material by measuring the coefficient of friction (CoF) as well as the mechanical properties and wettability through atomic force microscopy (AFM) and the contact angle, respectively. It was discovered that using these techniques, it is possible to recover approximately 95% of the additive present in the water while keeping the material’s properties within the desired limits

Caprolactam is a highly useful monomer obtained through the Beckmann arrangement, which generates large profits worldwide and is widely used in different industries. During the synthesis process, various components can be generated that weaken the quality of the final product, to have control of the monomer, monitoring is carried out during the synthesis and characterization of the final product. These characterizations generally take time due to the different techniques that must be performed to obtain the data. In this work, a method is designed that associates different techniques to reduce the number of steps carried out in the tests to determine the qual- ity of the material, optimize the times and generate a quality and efficient process in a shorter time, in addition, it is due to a semi-automated system for the simultaneous characterization of caprolactam, which, according to the statistical data obtained for sodium, iron, volatile bases, and moisture analysis were reproducible. The developed prototype had 21 on-line valves that allowed taking the representative volumes of samples and reagents necessary for each measure- ment. There is excellent linearity where the correlation coefficient has values between 0,9992 and 1. The values obtained for the relative error are between 0.18 and 2.24% for laboratory tests using the traditional method and between 0.21 and 3.83% for tests carried out using the proto- type. The P value of the evaluation of the means was 0.997, indicating that the means are not statistically different.

In this study, the total atmospheric deposition of microplastics in places near an industrial complex in Cartagena, Colombia is evaluated by taking samples at three points at different distances from the industrial zone. The samples obtained were treated to quantify and identify the type of plastic present, indicating the presence of polystyrene, polypropylene, polyethylene, polyvinyl chloride, and polyethylene terephthalate. The values of microplastics obtained were related to the climatic conditions of the areas (wind and rainfall) to determine these effects on the transport of microplastics. Values of 9472 ± 702 MP were obtained at the point closest to the industrial area and 1455 ± 14 MP at the farthest point, within which a greater proportion were fibers. In this study, it was also possible to determine that the microplastics most affected by the wind were the fragments. © 2022 by the authors.

The use of biodegradable biopolymers with the incorporation of active ingredients has been considered as an alternative to extend the useful life of food. Therefore, the objective of this research was to develop active films based on starch and wheat gluten, containing cinnamon and turmeric essential oils by using the solvent casting method. Different film formulations were made from wheat starch, gluten, glycerol, and essential oils of cinnamon and turmeric. The films were characterized according to their morphology, optical, thermal, antioxidant, and barrier properties. Subsequently, the active properties on baby carrots regarding weight loss, appearance, and fungal growth were evaluated. The results indicated that the starch-based films showed a slight decrease in moisture content with the addition of essential oils (up to 13.29%), but at the same time showed a significant reduction in water solubility (up to 28.4%). Gluten-based films did not present significant differences in these parameters, although the solubility in water tended to increase (up to 13.15%) with the addition of essential oils. In general, the films presented good thermal stability and antioxidant capacity, and in the carrot coating test, a decrease in weight loss of up to 44.44% and 43.33% was observed for the coatings based on starch and gluten with the addition of turmeric essential oil, respectively. Finally, films developed with cinnamon and turmeric essential oils are potential candidates for the design of biodegradable active packaging. © 2022 by the authors.

For the synthesis of polymeric resins, it is of great importance to review the raw materials and the equipment to be used to avoid the presence of compounds that may affect the effectiveness of the polymerization and the characteristics of the plastic to be obtained. Iron oxide is a compound that can be present in reactors after maintenance due to the techniques used and the cleaning of this equipment, and it can affect the characteristics of the resins, reducing their quality. In this study, the presence of FeO in different concentrations was evaluated to determine its effects on the properties and pyrolysis of polypropylene resins by using X-ray refraction to determine the elements of the samples, evaluating thermal degradation by TGA, the variation in molecular weight by measuring the MFI, and the compounds obtained from pyrolysis by chromatography. The results showed that the thermal degradation decreased as the FeO concentration increased, while for the MFI, the relationship was directly proportional. The evaluation of the compounds obtained from pyrolysis showed an increase in the production of alcohols, alkynes, ketones, and acids, and a decrease in alkanes and alkenes, showing that FeO affects the properties of polypropylene and the compounds that are produced during pyrolysis. © 2022 by the authors.

During the production of polymer-grade propylene, different processes are used to purify this compound and ensure that it is of the highest quality. However, some impurities such as acetylene and methyl acetylene are difficult to remove, and some of these impurities may be present in the propylene used to obtain polypropylene, which may have repercussions on the process. This study evaluates the impact of these acetylene and methyl acetylene impurities on the productivity of the polypropylene synthesis process and on the mechanical and thermal properties of the material obtained through the synthesis of eight samples with different concentrations of acetylene and eight samples with different concentrations of acetylene. We discovered that for the first concentrations of both acetylene (2 and 3 ppm) and methyl acetylene (0.03 and 0.1), the MFI, thermal recording, and mechanical properties of the resin were unaffected by the variation of the fluidity index, thermal degradation by TGA, and mechanical properties such as resistance to tension, bending, and impact. However, when the concentration exceeded 14 ppm for methyl acetylene and 12 ppm for acetylene, the resistance of this resin began to decrease linearly. Regarding production, this was affected by the first traces of acetylene and methyl acetylene progressively decreasing. © 2022 by the authors.