Search

The interaction of human proteins and metal species, both ions and nanoparticles, is poorly understood despite their growing importance. These materials are the by-products of corrosion processes and are of relevance for food and drug manufacturing, nanomedicine, and biomedical implant corrosion. Here, we study the interaction of Cr(III) ions and chromium oxide nanoparticles with bovine serum albumin in physiological conditions. This study combined electrophoretic mobility measurements, spectroscopy, and time-of-flight secondary ion mass spectrometry with principal component analysis. It was determined that neither metal species resulted in global albumin unfolding. The Cr(III) ions interacted strongly with amino acids found in previously discovered metal binding sites, but also were most strongly implicated in the interaction with negatively charged acid residues, suggesting an electrostatic interaction. Bovine serum albumin (BSA) was found to bind to the Cr 2 O 3 nanoparticles in a preferential orientation, due to electrostatic interactions between the positive amino acid residues and the negative chromium oxide nanoparticle surface. These findings ameliorate our understanding of the interaction between trivalent chromium ions and nanoparticles, and biological macromolecules., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Zoltan Richter-Bisson reports financial support was provided by Ontario Ministry of Colleges and Universities. Yolanda Hedberg reports financial support was provided by Ontario Ministry of Colleges and Universities. Yolanda Hedberg reports financial support was provided by Canada Foundation for Innovation. Yolanda Hedberg reports financial support was provided by Natural Sciences and Engineering Research Council of Canada. Yolanda Hedberg reports financial support was provided by Canada Research Chairs Program. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

Introduction: Leather has been a significant source of chromium (Cr) allergy in Denmark since the 1990s. More recently, cobalt (Co) allergy has been identified in leather as a source of allergic contact dermatitis., Objectives: To measure Cr and Co levels in Danish leather goods., Methods: A total of 87 leather samples were collected, all tanned in Europe. Handheld X-ray fluorescence (XRF) device was used to screen for the presence of Cr and Co. The 20 leather samples with the highest concentrations of Co and Co were tested using International Organization for Standardization (ISO)-standards., Results: XRF analysis showed Cr in 78/87 (83.9%) samples and Co in 52/87 (59.7%), with average concentrations of 41 mg/kg (range: 0.0-77 mg/kg) and 0.22 mg/kg (range: 0.0-2.9 mg/kg), respectively. ISO 10195 and 17 075-1 testing identified Cr (VI) in 7 out of 20 samples (1.4; 0.3-4.2 mg/kg), while ISO 17072-1 detected Co in 6 of 20 samples, averaging 3.95 mg/kg (range: 0.22-7.9 mg/kg)., Conclusion: Most leather samples contained Cr, which was expected, while Cr (VI) was detectable in seven out of twenty tested samples but only detected in one product above the regulatory limit of 3 mg/kg. A potentially significant concentration was found for Co., (© 2024 The Author(s). Contact Dermatitis published by John Wiley & Sons Ltd.)

Cobalt-chromium-molybdenum (CoCrMo) alloys are common wear-exposed biomedical alloys and are manufactured in multiple ways, increasingly using additive manufacturing processes such as laser powder bed fusion (LPBF). Here, we investigate the effect of proteins and the manufacturing process (wrought vs LPBF) and building orientation (LPBF- XY and XZ ) on the corrosion, metal release, tribocorrosion, and surface oxide composition by means of electrochemical, mechanical, microscopic, diffractive, and spectroscopic methods. The study was conducted at pH 7.3 in 5 g/L NaCl and 5 mM 2-( N -morpholino) ethanesulfonic acid (MES) buffer, which was found to be necessary to avoid metal phosphate and metal-protein aggregate precipitation. The effect of 10 g/L bovine serum albumin (BSA) and 2.5 g/L fibrinogen (Fbn) was studied. BSA and Fbn strongly enhanced the release of Co, Cr, and Mo and slightly enhanced the corrosion (still in the passive domain) for all CoCrMo alloys and most for LPBF- XZ , followed by LPBF- XY and the wrought CoCrMo. BSA and Fbn, most pronounced when combined, significantly decreased the coefficient of friction due to lubrication, the wear track width and severity of the wear mechanism, and the tribocorrosion for all alloys, with no clear effect of the manufacturing type. The wear track area was significantly more oxidized than the area outside of the wear track. In the reference solution without proteins, a strong Mo oxidation in the wear track surface oxide was indicative of a pH decrease and cell separation of the anodic and cathodic areas. This effect was absent in the presence of the proteins.

The interaction of serum proteins with cobalt (Co) and chromium (Cr) ions is poorly understood, but it is suspected to result in protein aggregation, which may alter the corrosion process of biomedical CoCr alloys or result in adverse health effects. Here, we study the aggregation ability and mechanism of bovine serum albumin (BSA) induced or accelerated by aqueous Co(II) and Cr(III) ions. The metal salts were selected by chemical speciation modeling, and they did not affect the pH or precipitate under simulated physiological conditions (150 mM NaCl and pH 7.3). The counterion of Cr(III) influenced the binding to BSA only at physiologically irrelevant low ionic strength. This study used a variety of spectroscopic and light scattering methods. It was determined that both metal ions and an equimolar mixture of metal ions have the potential to induce protein aggregation. Melting curves collected by circular dichroism spectroscopy indicate that Co(II) significantly reduced BSA's melting temperature when compared with Cr(III) or an equimolar mixture of Co(II) and Cr(III), both of which increased the melting temperature of BSA. The metal ions in solution preferentially interacted with BSA, resulting in the depletion of metal ions from the surrounding protein-free solution. Finally, this study suggests that the likely mechanism for Co(II)- and Cr(III)-induced BSA aggregation is salt bridging between protein molecules.

The European Union restricted the amount of hexavalent chromium (Cr(VI)) in leather in 2015, but skin allergy cases due to Cr-tanned leather are not declining. Standardized extraction methods have been criticized to both over- and underestimate the expected amount of bioavailable Cr(VI) in leather. This study aims to evaluate the ability of four extraction solutions to reduce or preserve Cr(VI): artificial sweat solutions (ASWs) of pH 4.7, 6.5, and 8.0, and phosphate buffer (PB) of pH 8.0. This was investigated by incubating each solution with added Cr(VI) as a function of time, and then measuring the recovered Cr(VI). All solutions, especially PB, preserved Cr(VI) for 24 h. These solutions were also pre-exposed to Cr-free vegetable-tanned leather (VTL) before incubation with Cr(VI). Released vegetable tannin species strongly reduced Cr(VI), with up to 4000 μg/L added Cr(VI) reduced in all solutions after 24 h. However, after 1 h, Cr(VI) was still detectable in extraction solutions at pH 6.5 and above. The reduction of Cr(VI) in relevant extraction solutions is hence a process dependent on time, pH, and the presence of co-released leather species. All extraction solutions, but least PB, have the potential to underestimate any Cr(VI) present on the surface of leather., (Copyright © 2022 Elsevier Inc. All rights reserved.)

Background: Allergic contact dermatitis to metals is diagnosed by applying a metal salt in a patch test. The bioavailability of the metal salt might depend on the choice of metal salt, the concentration, sweat composition, and pH., Objectives: The main purpose of this study was to apply chemical speciation modelling, which is based on experimentally derived input data and calculates the concentrations of chemical forms (species) in solutions, to reproduce and discuss clinical patch test results of aluminium and chromium., Methods: Joint Expert Speciation System (JESS), Hydra/Medusa, and Visual MINTEQ were employed to study the bioavailable fraction and chemical form of clinically applied aluminium and chromium salts as a function of salt type, applied concentration, sweat composition, and pH., Results: Investigated aluminium and chromium salts can have a very low bioavailability with a large dependency on sweat composition, pH, metal salt, and concentration. Both aluminium and chromium ions could shift the pH towards acidic or basic values based on their chemical form., Conclusions: Reported seasonal and interpatient variability in positive reactions to aluminium is likely related to sweat pH and composition. Potassium dichromate increases the pH, whereas aluminium and trivalent chromium chloride strongly decrease the pH, possibly increasing skin diffusion., (© 2021 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Welders are daily exposed to various levels of welding fumes containing several metals. This exposure can lead to an increased risk for different health effects which serves as a driving force to develop new methods that generate less toxic fumes. The aim of this study was to explore the role of released metals for welding particle-induced toxicity and to test the hypothesis that a reduction of Cr(VI) in welding fumes results in less toxicity by comparing the welding fume particles of optimized Cr(VI)-reduced flux-cored wires (FCWs) to standard FCWs. The welding particles were thoroughly characterized, and toxicity (cell viability, DNA damage and inflammation) was assessed following exposure to welding particles as well as their released metal fraction using cultured human bronchial epithelial cells (HBEC-3kt, 5-100 µg/mL) and human monocyte-derived macrophages (THP-1, 10-50 µg/mL). The results showed that all Cr was released as Cr(VI) for welding particles generated using standard FCWs whereas only minor levels (< 3% of total Cr) were released from the newly developed FCWs. Furthermore, the new FCWs were considerably less cytotoxic and did not cause any DNA damage in the doses tested. For the standard FCWs, the Cr(VI) released in cell media seemed to explain a large part of the cytotoxicity and DNA damage. In contrast, all particles caused rather similar inflammatory effects suggesting different underlying mechanisms. Taken together, this study suggests a potential benefit of substituting standard FCWs with Cr(VI)-reduced wires to achieve less toxic welding fumes and thus reduced risks for welders., (© 2021. The Author(s).)

Background: Tattoo inks have been reported to elicit allergic contact dermatitis., Objectives: To investigate the labels and the contents of metals and pigments in tattoo inks, considering restrictions within the European Union., Methods: Seventy-three tattoo inks currently available on the market, either bought or donated (already used), were investigated for trace metals and pigments by inductively coupled plasma mass spectrometry and by matrix-assisted laser desorption/ionization time of flight tandem mass spectrometry., Results: Ninety-three percent of the bought tattoo inks violated European, legal requirements on labeling. Fifty percent of the tattoo inks declared at least one pigment ingredient incorrectly. Sixty-one percent of the inks contained pigments of concern, especially red inks. Iron, aluminium, titanium, and copper (most in green/blue inks) were the main metals detected in the inks. The level of metal impurities exceeded current restriction limits in only a few cases. Total chromium (0.35-139 μg/g) and nickel (0.1-41 μg/g) were found in almost all samples. The levels of iron, chromium, manganese, cobalt, nickel, zinc, lead, and arsenic were found to covary significantly., Conclusions: To prevent contact allergy and toxic reactions among users it is important for tattoo ink manufacturers to follow the regulations and decrease nickel and chromium impurities., (© 2021 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Welding fume particles are hazardous. Their toxicity likely depends on their composition and reactivity. This study aimed at exploring the role of sodium or other fluorides (NaF), which are intentionally added to flux-cored wire electrodes for stainless steel welding, on the solubility (in phosphate buffered saline) and toxicity of the generated welding fume particles. A multi-analytical particle characterization approach along with in-vitro cell assays was undertaken. The release of Cr(VI) and Mn from the particles was tested as a function of fluoride solution concentration. The welding fume particles containing NaF released significantly higher amounts of Cr(VI) compared with solid wire reference fumes, which was associated with increased cytotoxicity and genotoxicity in-vitro. No crystalline Na or potassium (K) containing chromates were observed. Cr(VI) was incorporated in an amorphous mixed oxide. Solution-added fluorides did not increase the solubility of Cr(VI), but contributed to a reduced Mn release from both solid and flux-cored wire fume particles and the reduction of Cr(VI) release from solid wire fume particles. Chemical speciation modeling suggested that metal fluoride complexes were not formed. The presence of NaF in the welding electrodes did not have any direct, but possibly an indirect, role in the Cr(VI) solubility of welding fumes., (Copyright © 2021 The Authors. Published by Elsevier B.V. All rights reserved.)

Gold (Au) nanoparticles (NPs) are widely used in nanomedical applications as a carrier for molecules designed for different functionalities. Previous findings suggested that biological molecules, including amino acids, could contribute to the dissolution of Au NPs in physiological environments and that this phenomenon was size-dependent. We, therefore, investigated the interactions of L-cysteine with 5-nm Au NPs by means of time-of-flight secondary ion mass spectrometry (ToF-SIMS). This was achieved by loading Au NPs on a clean aluminum (Al) foil and immersing it in an aqueous solution containing L-cysteine. Upon rinsing off the excessive cysteine molecules, ToF-SIMS confirmed the formation of gold cysteine thiolate via the detection of not only the Au-S bond but also the hydrogenated gold cysteine thiolate molecular ion. The presence of NaCl or a 2-(N-morpholino)ethanesulfonic acid buffer disabled the detection of Au NPs on the Al foil. The detection of larger (50-nm) Au NPs was possible but resulted in weaker cysteine and gold signals, and no detected gold cysteine thiolate signals. Nano-gold specific adsorption of L-cysteine was also demonstrated by cyclic voltammetry using paraffine-impregnated graphite electrodes with deposited Au NPs. We demonstrate that the superior chemical selectivity and surface sensitivity of ToF-SIMS, via detection of elemental and molecular species, provide a unique ability to identify the adsorption of cysteine and formation of gold-cysteine bonds on Au NPs.

Background: Contact allergy to aluminium (Al) might pose a risk of false-positive readings of patch-test results when testing with Finn chambers., Objectives: To quantify the release of Al from empty Al Finn chambers, covered Finn Aqua chambers, and Al Finn chambers containing different baseline patch-test substances., Methods: Al Finn chambers of different conditions and with different patch-test substances were tested in artificial sweat and their Al release was analyzed by atomic absorption spectroscopy and inductively coupled plasma sector field mass spectrometry., Results: The amount of Al released from empty Finn chambers corresponded to a skin dose of 0.03%-0.5% Al chloride hexahydrate applied in plastic chambers. Although most patch-test substances reduced the release of Al from the Finn chambers due to covering the surface, some substances significantly increased the release of Al from the Finn chambers, most notable for Caine mix II 10% pet., Myroxylon pereirae 25% pet., and sodium tetrachloropalladate hydrate 3.0% pet., Conclusions: The release of Al from Finn chambers corresponds in some cases to clinically relevant concentrations of Al for Al-sensitized individuals., (© 2020 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Background: Exposure to metalworking fluids (MWFs) is a well-known cause of occupational contact dermatitis., Objectives: We aimed to (1) determine the amount of nickel, chromium, and cobalt in large samples of used and unused MWFs collected from metalworking plants in Denmark, and (2) evaluate a handheld x-ray fluorescence (XRF) device as a screening instrument for metals in MWFs., Methods: A handheld XRF device was used to screen for metals in MWFs. All samples were also analyzed for concentrations of nickel, chromium, and cobalt using graphite furnace atomic absorption spectroscopy (GFAAS)., Results: GFAAS analysis showed that 13 of 80 samples (16.3%) contained >1 mg/kg (ppm) nickel (range: 6.4-17.7 mg/kg), 3 of 80 (3.8%) contained >1 (range: 1.4-3.1) mg/kg chromium, and 1 of 80 (1.3%) contained 1.3 mg/kg cobalt. XRF-screening detected nickel in eight samples (range: 2.5-15.5 mg/kg), but only one sample with 3.0 (±0.5) mg/kg was found subsequently to contain 9.9 (0.02) mg/kg nickel by GFAAS. Although no chromium was found by XRF analysis, cobalt was found in two samples with 6 (±1.5) mg/kg and 5 (±1.5) mg/kg, subsequently found to contain 0.1 (±0.01) mg/kg and 0.08 (±0.01) mg/kg by GFAAS. Similar concentrations of nickel were found in used (N = 6, range: 6.4-17.7 mg/kg) and unused MWFs (N = 7, range: 9.1-17.3 mg/kg)., Conclusion: Considerable levels of nickel, chromium, and cobalt were found in some used and unused MWFs indicating that these might represent a source of metal allergy. The XRF device is a poor screening test for these metals in MWFs., (© 2020 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Hexavalent chromium in cement 5-8 mg/kg hexavalent chromium (Cr(VI)) was found in Honduran cement samples, which was slightly higher than in Swedish samples. Variable amounts of Cr(VI) (0.4 and 4.7 mg/kg) found in Swedish cement samples that were older than 1 year. There are still many countries that do not have a compulsory reduction of Cr(VI) in cement. Several measures can be employed to reduce risks related to Cr(VI) in cement., (© 2020 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Surface disinfection of water facilities such as water wells requires measures that can remove pathogens from the walls to ensure a high drinking water quality, but many of these measures might increase corrosion of the contact surfaces (often highly pure steel) and affect the environment negatively due to disinfectant-contaminated waste sludge and wastewater. Today, most treatments worldwide are based on hypochlorites. We investigated the extent of corrosion during treatments of steel at relevant conditions of ozone, sodium, and calcium hypochlorite for drinking water preparation, utilizing weight loss, electrochemical, solution analytical, and surface analytical methods. The ozone treatment caused significantly less corrosion as compared with sodium or calcium hypochlorite with 150-250 mg/L active chlorine. Hypochlorite or other chlorine-containing compounds were trapped in corrosion products after the surface disinfection treatment with hypochlorite, and this risked influencing subsequent corrosion after the surface disinfection treatment. A life cycle impact assessment suggested ozone treatment to have the lowest negative effects on human health, ecosystems, and resources. Calcium hypochlorite showed the highest negative environmental impact due to its production phase. Our study suggests that ozone surface disinfection treatments are preferable as compared with hypochlorite treatments from corrosion, economic, and environmental perspectives.

The titanium-aluminium (6 wt%)-vanadium (4 wt%) (Ti6Al4V) alloy is widely used as an orthopedic and dental implant material due to its high corrosion resistance in such environments. The corrosion resistance is usually determined by means of electrochemical methods, which may not be able to detect other chemical surface reactions. Literature findings report a synergistic effect of the combination of the abundant protein albumin and hydrogen peroxide (H 2 O 2 ) on the extent of metal release and corrosion of Ti6Al4V. The objectives of this study were to gain further mechanistic insight on the interplay of H 2 O 2 and albumin on the metal release process of Ti6Al4V with special focus on (1) kinetics and (2) H 2 O 2 and albumin concentrations. This was accomplished mainly by metal release and surface oxide composition investigations, which confirmed the combined effect of H 2 O 2 and albumin on the metal release process, although not detectable by electrochemical open circuit potential measurements. A concentration of 30 mM H 2 O 2 induced substantial changes in the surface oxide characteristics, an oxide which became thicker and enriched in aluminum. Bovine serum albumin (BSA) seemed to be able to deplete this aluminum content from the outermost surface or at least to delay its surface enrichment. This effect increased with increased BSA concentration, and for time periods longer than 24 h. This study hence suggests that short-term (accelerated) corrosion resistance measurements are not sufficient to predict potential health effects of Ti6Al4V alloys since also chemical dissolution mechanisms play a large role for metal release, possibly in a synergistic way. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 855-867, 2019., (© 2018 The Authors. Journal of Biomedical Materials Research Part B: Applied Biomaterials published by Wiley Periodicals, Inc.)

Gold nanoparticles (AuNPs) are readily functionalized and considered biocompatible making them useful in a wide range of applications. Upon human exposure, AuNPs will to a high extent reside in macrophages, cells that are designed to digest foreign materials. To better understand the fate of AuNPs in the human body, their possible dissolution needs to be explored. In this study, we tested the hypothesis that macrophages, and especially stimulated macrophages, can impact the dissolution of AuNPs in a size-dependent manner. We developed an in vitro method to compare the dissolution of citrate coated 5 and 50 nm-sized AuNPs, in terms of released gold ions as measured by inductive coupled mass spectrometry (ICP-MS), in (i) cell medium (alone) (ii) in medium with macrophages present and (iii) in medium with lipopolysaccharide (LPS) triggered macrophages (simulating inflammatory conditions). We found an evident, time-dependent dissolution of AuNPs in cell medium, corresponding to 3% and 0.6% of the added amounts of 5 and 50 nm AuNPs, respectively, after 1 week (168 h) of incubation. The dissolution of 5 nm AuNPs was further increased to 4% in the presence of macrophages and, most strikingly, 14% was dissolved in case of LPS-triggering. In contrast, only a minor increase was observed for 50 nm AuNPs after 1 week in the presence of LPS-triggered macrophages compared to medium alone. Dissolution experiments in the absence of cells highlighted the importance of biomolecules. Our findings thus show dissolution of citrate coated AuNPs that is dependent on size, presence of macrophages, and their inflammatory state. These findings have implications for understanding the transformation/dissolution and fate of AuNPs.

Background: Leather exposure has been associated with chromium (Cr) and cobalt (Co) contact dermatitis. Cr(VI) in leather is now restricted to <3 mg/kg in the EU. Cr(III) is not restricted., Objectives: To analyse 29 differently coloured Cr-tanned leather samples from two Nicaraguan tanneries, and to compare their release of Cr, Cr(VI) and Co with that of leathers produced in Europe., Methods: Cr, Cr(VI) and Co were extracted in phosphate buffer for 3 hours at 25°C according to EN ISO 17075. Atomic absorption spectroscopy and spectrophotometry were used for detection of the metals in phosphate buffer., Results: There was no difference in total Cr or Cr(VI) release between European and Nicaraguan leathers. There was no association between Cr(VI) and total Cr release. Co was released primarily from leathers of one tannery. Cr(III) was released in significantly higher amounts than Cr(VI)., Conclusions: Future investigations and regulations should focus on Cr(III) and Co as well as on Cr(VI)., (© 2018 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Exposure to cobalt (Co), chromium (Cr), and nickel (Ni) occurs often via skin contact and from different dental and orthopedic implants. The metal ions bind to proteins, which may induce structural changes and aggregation, with different medical consequences. We investigated human serum albumin (HSA) aggregation in the presence of Co II , Cr III , and/or Ni II ions and/or their nanoparticle precipitates by using scattering, spectroscopic, and imaging techniques, at simulated physiological conditions (phosphate buffered saline - PBS, pH 7.3) using metal salts that did not affect the pH, and at HSA:metal molar ratios of up to 1:8. Co ions formed some solid nanoparticles in PBS at the investigated conditions, as determined by nanoparticle tracking analysis, but the Cr III anions and Ni II ions remained fully soluble. It was found that all metal ions induced HSA aggregation, and this effect was significantly enhanced when a mixture of all three metal ions was present instead of any single type of ion. Thus, the metal ions induce aggregation synergistically. HSA aggregates formed linear structures on a mica surface in the presence of Cr III ions. A clear tendency of aggregation and linearly aligned aggregates was seen in the presence of all three metal ions. Spectroscopic investigations indicated that the majority of the HSA molecules maintained their alpha helical secondary structure and conformation. This study highlights the importance of synergistic effects of metal ions and/or their precipitates on protein aggregation, which are highly relevant for implant materials and common exposures to metals., (Copyright © 2018 The Author(s). Published by Elsevier B.V. All rights reserved.)

Background: Hair dyeing is very common and may cause allergic contact dermatitis. Oxidative (often termed permanent or semi-permanent) hair dye products have constituted the focus of market surveys and toxicological risk assessments, while non-oxidative (semi-permanent, temporary or direct) products have not been assessed., Objectives: To identify the hair dye substances presently used in non-oxidative hair dye products in Europe., Methods: Ingredient label data on eligible products in 5 European countries were collected, and 289 different non-oxidative hair dye products were included in this study., Results: Up to 9 hair dye substances were present in each product. Sixty-eight individual hair dye substances were identified on the 289 product labels, and their occurrence ranged from 0.3% to 34%. There were differences concerning substances used and their number per product between products of different consistency and colour., Conclusions: The hair dye substances in non-oxidative hair dye products are different from those in oxidative hair dye products, and are currently not covered by patch test series. The toxicological and skin-sensitizing profile of the substances in non-oxidative hair dye products, as well as their concentrations, should be further investigated., (© 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Background: Chromium (Cr) is a common skin sensitizer. The use of Cr(VI) in leather is restricted in the EU, but that of Cr(III) is not., Objectives: To assess whether prolonged exposure to Cr-tanned leather with mainly Cr(III) release may elicit allergic contact dermatitis in Cr-allergic individuals., Method: Ten Cr-allergic subjects and 22 controls were patch tested with serial dilutions of Cr(III) and Cr(VI), and with leather samples. They then conducted a use test with a Cr-tanned and a Cr-free leather bracelet over a period of 3 weeks, for 12 h per day. Cr deposited on the skin from the bracelets was measured in the controls, and the diphenylcarbazide test for Cr(VI) and extraction tests for Cr(III) and Cr(VI) were conducted for the different leathers., Results: Four of 10 Cr-allergic subjects developed positive reactions to the Cr-tanned bracelet within 7-21 days, whereas only 1 of 10 had a positive patch test reaction to this leather. Cr released from the Cr-tanned leather was most probably entirely Cr(III), with a quantifiable amount being deposited on the skin., Conclusions: This study strongly suggests that prolonged and repeated exposure to Cr-tanned leather with mainly Cr(III) release is capable of eliciting allergic contact dermatitis in Cr-allergic individuals., (© 2018 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Metallic nanoparticles (NPs) are promising nanomaterials used in different technological solutions as well as in consumer products. Silver (Ag), gold (Au) and platinum (Pt) represent three metallic NPs with current or suggested use in different applications. Pt is also used as vehicle exhaust catalyst leading to a possible exposure via inhalation. Despite their use, there is limited data on their genotoxic potential and possible size-dependent effects, particularly for Pt NPs. The aim of this study was to explore size-dependent genotoxicity of these NPs (5 and 50 nm) following exposure of human bronchial epithelial cells. We characterised the NPs and assessed the viability (Alamar blue assay), formation of DNA strand breaks (mini-gel comet assay) and induction of micronucleus (MN) analysed using flow cytometry (in vitro microflow kit). The results confirmed the primary size (5 and 50 nm) but showed agglomeration of all NPs in the serum free medium used. Slight reduced cell viability (tested up to 50 µg/ml) was observed following exposure to the Ag NPs of both particle sizes as well as to the smallest (5 nm) Au NPs. Similarly, at non-cytotoxic concentrations, both 5 and 50 nm-sized Ag NPs, as well as 5 nm-sized Au NPs, increased DNA strand breaks whereas for Pt NPs only the 50 nm size caused a slight increase in DNA damage. No clear induction of MN was observed in any of the doses tested (up to 20 µg/ml). Taken together, by using the comet assay our study shows DNA strand breaks induced by Ag NPs, without any obvious differences in size, whereas effects from Au and Pt NPs were size-dependent in the sense that the 5 nm-sized Au NPs and 50 nm-sized Pt NPs particles were active. No clear induction of MN was observed for the NPs.

Welding fume of stainless steels is potentially health hazardous. The aim of this study was to investigate the manganese (Mn) and chromium (Cr) speciation of welding fume particles and their extent of metal release relevant for an inhalation scenario, as a function of particle size, welding method (manual metal arc welding, metal arc welding using an active shielding gas), different electrodes (solid wires and flux-cored wires) and shielding gases, and base alloy (austenitic AISI 304L and duplex stainless steel LDX2101). Metal release investigations were performed in phosphate buffered saline (PBS), pH 7.3, 37°, 24h. The particles were characterized by means of microscopic, spectroscopic, and electroanalytical methods. Cr was predominantly released from particles of the welding fume when exposed in PBS [3-96% of the total amount of Cr, of which up to 70% as Cr(VI)], followed by Mn, nickel, and iron. Duplex stainless steel welded with a flux-cored wire generated a welding fume that released most Cr(VI). Nano-sized particles released a significantly higher amount of nickel compared with micron-sized particle fractions. The welding fume did not contain any solitary known chromate compounds, but multi-elemental highly oxidized oxide(s) (iron, Cr, and Mn, possibly bismuth and silicon)., (Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.)

Studded tyres made of tungsten carbide cobalt (WC-Co) are in the Northern countries commonly used during the winter time. Tungsten (W)-containing nano- and micron-sized particles have been detected close to busy roads in several European countries. Other typical traffic wear particles consist of copper (Cu). The aims of this study were to investigate particle stability and transformation/dissolution properties of nanoparticles (NPs) of WC-Co compared with NPs of tungsten carbide (WC), cobalt (Co), and Cu. Their physicochemical characteristics (primarily surface oxide and charge) are compared with their extent of sedimentation and metal release in synthetic surface water (SW) with and without two different model organic molecules, 2,3- and 3,4-dihydroxybenzoic acid (DHBA) mimicking certain sorption sites of humic substances, for time periods up to 22 days. The WC-Co NPs possessed a higher electrochemical and chemical reactivity in SW with and without DHBA molecules as compared with NPs of WC, Co, and Cu. Co was completely released from the WC-Co NPs within a few hours of exposure, although it remained adsorbed/bonded to the particle surface and enabled the adsorption of negatively charged DHBA molecules, in contrast with the WC NPs (no adsorption of DHBA). The DHBA molecules were found to rapidly adsorb on the Co and Cu NPs. The sedimentation of the WC and WC-Co NPs was not influenced by the presence of the 2,3- or 3,4-DHBA molecules. A slight influence (slower sedimentation) was observed for the Co NPs, and a strong influence (slower sedimentation) was observed for the Cu NPs in SW with 2,3-DHBA compared with SW alone. The extent of metal release increased in the order: WC < Cu < Co < WC-Co NPs. All NPs released more than 1 wt-% of their metal total mass. The release from the Cu NPs was most influenced by the presence of DHBA molecules., (Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The European chemical framework REACH requires that hazards and risks posed by chemicals, including alloys and metals, are identified and proven safe for humans and the environment. Therefore, differences in bioaccessibility in terms of released metals in synthetic biological fluids (different pH (1.5-7.4) and composition) that are relevant for different human exposure routes (inhalation, ingestion, and dermal contact) have been assessed for powder particles of an alloy containing high levels of nickel (Inconel 718, 57 wt% nickel). This powder is compared with the bioaccessibility of two nickel-containing stainless steel powders (AISI 316L, 10-12% nickel) and with powders representing their main pure alloy constituents: two nickel metal powders (100% nickel), two iron metal powders and two chromium metal powders. X-ray photoelectron spectroscopy, microscopy, light scattering, and nitrogen absorption were employed for the particle and surface oxide characterization. Atomic absorption spectroscopy was used to quantify released amounts of metals in solution. Cytotoxicity (Alamar blue assay) and DNA damage (comet assay) of the Inconel powder were assessed following exposure of the human lung cell line A549, as well as its ability to generate reactive oxygen species (DCFH-DA assay). Despite its high nickel content, the Inconel alloy powder did not release any significant amounts of metals and did not induce any toxic response. It is concluded, that this is related to the high surface passivity of the Inconel powder governed by its chromium-rich surface oxide. Read-across from the pure metal constituents is hence not recommended either for this or any other passive alloy., (Copyright © 2016 The Author(s). Published by Elsevier Inc. All rights reserved.)

Background: Chromium (Cr) release from Cr-tanned leather articles is a major cause of Cr contact dermatitis. It has been suggested that Cr(VI) release from leather is not necessarily an intrinsic property of the leather, but is strongly dependent on environmental conditions., Objectives: To test this hypothesis for long-term (8 months) simulated use., Materials and Methods: The release of total Cr and Cr(VI) from Cr-tanned, unfinished leather was analysed in subsequent phosphate buffer (pH 8.0) immersions for a period of 7.5 months. The effect of combined ultraviolet treatment and alkaline solution (pH 12.1) was tested. Dry storage [20% relative humidity (RH)] was maintained between immersions. Atomic absorption spectroscopy, X-ray fluorescence and diphenylcarbazide tests were used., Results: Cr(VI) release was dependent on previous dry storage or alkaline treatment, but not on duration or number of previous immersions. Cr(III) release decreased with time. Fifty-two percent of the total Cr released during the last immersion period was Cr(VI). Cr(VI) release exceeded 9 mg/kg in all immersion periods except in the first 10-day immersion (2.6 mg/kg)., Conclusions: Cr(VI) release is primarily determined by environmental factors (RH prior to immersion, solution pH, and antioxidant content). The RH should be kept low prior to testing Cr(VI) release from leather., (© 2016 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Cobalt chromium molybdenum alloys (CoCrMo) are commonly used as articulating components in joint prostheses. In this tribocorrosive environment, wear debris and metal ionic species are released and interact with proteins, possibly resulting in protein aggregation. This study aimed to investigate whether this could have an effect on the friction coefficient in a typical material couple, namely CoCrMo-on-polyethylene. It was confirmed that both Co(II) and Cr(III) ions, and their combination, at concentrations relevant for the metal release situation, resulted in protein aggregation and its concomitant precipitation, which increased the friction coefficient. Future studies should identify the clinical importance of these findings.

Background: Approximately 1-3% of the adult population in Europe are allergic to chromium (Cr). A new restriction in Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) based on the ISO 17075 standard has recently been adopted in the EU to limit Cr(VI) in consumer and occupational leather products to < 3 mg/kg., Objectives: To investigate the influence of storage conditions [relative humidity, temperature, ultraviolet (UV) irradiation, and duration] on Cr release, and to assess several parameters relevant for occupational exposure (repeated exposure, wear, alkaline solutions, and sequential wet and dry exposures)., Material and Methods: A leather of relevance for work gloves was investigated for its release of Cr(III) and Cr(VI) under these different experimental conditions., Results: Relative humidity (water content in leather) during storage prior to Cr extraction was the single most important parameter. Cr(VI) levels could vary from non-detectable to levels significantly exceeding the restriction limit, depending on the relative humidity. Leather contact with alkaline solution and UV irradiation during storage could increase the Cr(VI) levels in subsequent extractions., Conclusions: The amount of Cr(VI) in leather is not an intrinsic property, but is influenced by environmental conditions of relevance for occupations and skin exposure., (© 2015 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Background: Approximately 1-3% of the adult population in Europe is allergic to chromium (Cr). A new restriction in REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) based on the ISO 17075 standard has recently been adopted in the EU to limit Cr(VI) in consumer and occupational leather products., Objectives: The aim of this study was to critically assess key experimental parameters in this standard on the release of Cr(III) and Cr(VI) and their relevance for skin exposure., Material and Methods: Four differently tanned, unfinished, leather samples were systematically investigated for their release of Cr(III) and Cr(VI) in relation to surface area, key exposure parameters, temperature, ultraviolet irradiation, and time., Results: Although the total release of Cr was largely unaffected by all investigated parameters, except exposure duration and temperature, the Cr oxidation state was highly dynamic, with reduced amounts of released Cr(VI) with time, owing to the simultaneous release of reducing agents from the leather. Significantly more Cr(III) than Cr(VI) was released from the Cr-tanned leather for all conditions tested, and it continued to be released in artificial sweat up to at least 1 week of exposure., Conclusions: Several parameters were identified that influenced the outcome of the ISO 17075 test., (© 2015 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.)

Due to its beneficial corrosion resistance, stainless steel is widely used in, e.g., biomedical applications, as surfaces in food contact, and for products intended to come into skin contact. Low levels of metals can be released from the stainless steel surface into solution, even for these highly corrosion resistant alloys. This needs to be considered in risk assessment and management. This review aims to compile the different metal release mechanisms that are relevant for stainless steel when used in different biological settings. These mechanisms include corrosion-induced metal release, dissolution of the surface oxide, friction-induced metal release, and their combinations. The influence of important physicochemical surface properties, different organic species and proteins in solution, and of biofilm formation on corrosion-induced metal release is discussed. Chemical and electrochemical dissolution mechanisms of the surface oxides of stainless steel are presented with a focus on protonation, complexation/ligand-induced dissolution, and reductive dissolution by applying a perspective on surface adsorption of complexing or reducing ligands and proteins. The influence of alloy composition, microstructure, route of manufacture, and surface finish on the metal release process is furthermore discussed as well as the chemical speciation of released metals. Typical metal release patterns are summarized.

Predictions of the diffuse dispersion of metals from outdoor constructions such as roofs and facades are necessary for environmental risk assessment and management. An existing predictive model has been compared with measured data of copper runoff from copper sheets exposed at four different inclinations facing four orientations at two different urban sites (Stockholm, Sweden, and Milan, Italy) during a 4-year period. Its applicability has also been investigated for copper sheet exposed at two marine sites(Cadiz, Spain, for 5 years, and Brest, France, for 9 years). Generally the model can be used for all given conditions. However, vertical surfaces should be considered as surfaces inclined 60-80 due to wind driven effects. The most important parameters that influence copper runoff, and not already included in the model, are the wind and rain characteristics that influence the actual rainfall volume impinging the surface of interest.

About 1-3% of the adult general population in Europe is allergic to chromium (Cr). The assessment of the potential release of Cr(III) and Cr(VI) from leather is hence important from a human health and environmental risk perspective. The Cr(VI) content in leather was recently restricted in the European Union. The aim of this study was to assess possible correlations between the bulk and surface chemistry of leather, released Cr(III) and Cr(VI), and capacities of co-released leather specific species to reduce and complex released Cr. Four differently tanned leathers were characterized by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, and the diphenylcarbazide colorimetric method. Their characteristics were compared with results on Cr(III) and Cr(VI) release into artificial sweat (ASW, pH<6.5) and phosphate buffer (PB, pH 7.5-8.0), measured by means of spectrophotometry and atomic absorption spectroscopy. Co-released leather-specific species were shown to reduce Cr(VI), both in ASW and in PB. Their reduction capacities correlated with findings of the surface content of Cr and of released Cr. Leather samples without this capacity, and with less aromatic surface groups visible by ATR-FTIR, revealed Cr(VI) both at the surface and in solution (PB)., (Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.)

Objective: Selective laser melting (SLM) is increasingly used for the fabrication of customized dental components made of metal alloys such as CoCrMo. The main aim of the present study is to elucidate the influence of the non-equilibrium microstructure obtained by SLM on corrosion susceptibility and extent of metal release (measure of biocompatibility)., Methods: A multi-analytical approach has been employed by combining microscopic and bulk compositional tools with electrochemical techniques and chemical analyses of metals in biologically relevant fluids for three differently SLM fabricated CoCrMo alloys and one cast CoCrMo alloy used for comparison., Results: Rapid cooling and strong temperature gradients during laser melting resulted in the formation of a fine cellular structure with cell boundaries enriched in Mo (Co depleted), and suppression of carbide precipitation and formation of a martensitic ɛ (hcp) phase at the surface. These features were shown to decrease the corrosion and metal release susceptibility of the SLM alloys compared with the cast alloy. Unique textures formed in the pattern of the melting pools of the three different laser melted CoCrMo alloys predominantly explain observed small, though significant, differences. The susceptibility for corrosion and metal release increased with an increased number (area) of laser melt pool boundaries., Significance: This study shows that integrative and interdisciplinary studies of microstructural characteristics, corrosion, and metal release are essential to assess and consider during the design and fabrication of CoCrMo dental components of optimal biocompatibility. The reason is that the extent of metal release from CoCrMo is dependent on fabrication procedures., (Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.)

This review on copper runoff dispersed from unsheltered naturally patinated copper used for roofing and facades summarizes and discusses influencing factors, available literature, and predictive models, and the importance of fate and speciation for environmental risk assessment. Copper runoff from outdoor surfaces is predominantly governed by electrochemical and chemical reactions and is highly dependent on given exposure conditions (size, inclination, geometry, degree of sheltering, and orientation), surface parameters (age, patina composition, and thickness), and site-specific environmental conditions (gaseous pollutants, chlorides, rainfall characteristics (amount, intensity, pH), wind direction, temperature, time of wetness, season). The corrosion rate cannot be used to assess the runoff rate. The extent of released copper varies largely between different rain events and is related to dry and wet periods, dry deposition prior to the rain event and prevailing rain and patina characteristics. Interpretation and use of copper runoff data for environmental risk assessment and management need therefore to consider site-specific factors and focus on average data of long-term studies (several years). Risk assessments require furthermore that changes in copper speciation, bioavailability aspects, and potential irreversible retention on solid surfaces are considered, factors that determine the environmental fate of copper runoff from outdoor surfaces.

An in-depth mechanistic understanding of the interaction between stainless steel surfaces and proteins is essential from a corrosion and protein-induced metal release perspective when stainless steel is used in surgical implants and in food applications. The interaction between lysozyme (LSZ) from chicken egg white and bovine serum albumin (BSA) and AISI 316L stainless steel surfaces was studied ex situ by means of X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) after different adsorption time periods (0.5, 24, and 168 h). The effect of XPS measurements, storage (aging), sodium dodecyl sulfate (SDS), and elevated temperature (up to 200 °C) on the protein layers, as well as changes in surface oxide composition, were investigated. Both BSA and LSZ adsorption induced an enrichment of chromium in the oxide layer. BSA induced significant changes to the entire oxide, while LSZ only induced a depletion of iron at the utmost layer. SDS was not able to remove preadsorbed proteins completely, despite its high concentration and relatively long treatment time (up to 36.5 h), but induced partial denaturation of the protein coatings. High-temperature treatment (200 °C) and XPS exposure (X-ray irradiation and/or photoelectron emission) induced significant denaturation of both proteins. The heating treatment up to 200 °C removed some proteins, far from all. Amino acid fragment intensities determined from ToF-SIMS are discussed in terms of significant differences with adsorption time, between the proteins, and between freshly adsorbed and aged samples. Stainless steel-protein interactions were shown to be strong and protein-dependent. The findings assist in the understanding of previous studies of metal release and surface changes upon exposure to similar protein solutions.