Search

Transition-metal dichalcogenide monolayers have naturally terminated surfaces and can exhibit a near-unity photoluminescence quantum yield in the presence of suitable defect passivation. To date, steady-state monolayer light-emitting devices suffer from Schottky contacts or require complex heterostructures. We demonstrate a transient-mode electroluminescent device based on transition-metal dichalcogenide monolayers (MoS2, WS2, MoSe2, and WSe2) to overcome these problems. Electroluminescence from this dopant-free two-terminal device is obtained by applying an AC voltage between the gate and the semiconductor. Notably, the electroluminescence intensity is weakly dependent on the Schottky barrier height or polarity of the contact. We fabricate a monolayer seven-segment display and achieve the first transparent and bright millimeter-scale light-emitting monolayer semiconductor device.

Two dimensional inorganic–organic hybrid perovskites (2D perovskites) suffer from not only quantum confinement, but also dielectric confinement, hindering their application perspective in devices involving the conversion of an optical input into current. In this report, we theoretically predict that an extremely low exciton binding energy can be achieved in 2D perovskites by using high dielectric-constant organic components. We demonstrate that in (HOCH2CH2NH3)2PbI4, whose organic material has a high dielectric constant of 37, the dielectric confinement is largely reduced, and the exciton binding energy is 20-times smaller than that in conventional 2D perovskites. As a result, the photo-induced excitons can be thermally dissociated efficiently at room temperature, as clearly indicated from femtosecond transient absorption measurements. In addition, the mobility is largely improved due to the strong screening effect on charge impurities. Such low dielectric-confined 2D perovskites show excellent carrier extraction efficiency, and outstanding humidity resistance compared to conventional 2D perovskites.

The recent development of 2D monolayer lateral semiconductor has created new paradigm to develop p-n heterojunctions. Albeit, the growth methods of these heterostructures typically result in alloy structures at the interface, limiting the development for high-efficiency photovoltaic (PV) devices. Here, the PV properties of sequentially grown alloy-free 2D monolayer WSe2 -MoS2 lateral p-n heterojunction are explores. The PV devices show an extraordinary power conversion efficiency of 2.56% under AM 1.5G illumination. The large surface active area enables the full exposure of the depletion region, leading to excellent omnidirectional light harvesting characteristic with only 5% reduction of efficiency at incident angles up to 75°. Modeling studies demonstrate the PV devices comply with typical principles, increasing the feasibility for further development. Furthermore, the appropriate electrode-spacing design can lead to environment-independent PV properties. These robust PV properties deriving from the atomically sharp lateral p-n interface can help develop the next-generation photovoltaics.

Despite great improvements in traditional inorganic photodetectors and photovoltaics, more progress is needed in the detection/collection of light at low-level conditions. Traditional photodetectors tend to suffer from high noise when operated at room temperature; therefore, these devices require additional cooling systems to detect weak or dim light. Conventional solar cells also face the challenge of poor light-harvesting capabilities in hazy or cloudy weather. The real world features such varying levels of light, which makes it important to develop strategies that allow optical devices to function when conditions are less than optimal. In this work, we report an organic/inorganic hybrid device that consists of graphene quantum dot-modified poly(3,4-ethylenedioxythiophene) polystyrenesulfonate spin-coated on Si for the detection/harvest of weak light. The hybrid configuration provides the device with high responsivity and detectability, omnidirectional light trapping, and fast operation speed. To demonstrate the potential of this hybrid device in real world applications, we measured near-infrared light scattered through human tissue to demonstrate noninvasive oximetric photodetection as well as characterized the device's photovoltaic properties in outdoor (i.e., weather-dependent) and indoor weak light conditions. This organic/inorganic device configuration demonstrates a promising strategy for developing future high-performance low-light compatible photodetectors and photovoltaics.

This study introduces a novel approach for fabricating vertically stacked mini-LED arrays, integrating InGaN yellow and blue epitaxial layers with a stress buffer layer to enhance optoelectronic characteristics and structural stability. This method significantly simplifies the LED design by reducing the need for RGB configurations, thus lowering costs and system complexity. Employing vertical stacking integration technology, the design achieves high-density, efficient white light production suitable for multifunctional applications, including automotive lighting and outdoor signage. Experimental results demonstrate the exceptional performance of the stacked yellow and blue mini-LEDs in terms of luminous efficiency, wavelength precision, and thermal stability. The study also explores the performance of these LEDs under varying temperature conditions and their long-term reliability, indicating that InGaN-based yellow LEDs offer superior performance over traditional AlGaInP yellow LEDs, particularly in high-temperature environments. This technology promises significant advancements in the design and application of lighting systems, with potential implications for both automotive and general illumination markets. [ABSTRACT FROM AUTHOR]

The thin-film vapor-liquid-solid (TF-VLS) growth technique presents a promising route for high quality, scalable, and cost-effective InP thin films for optoelectronic devices. Toward this goal, careful optimization of material properties and device performance is of utmost interest. Here, we show that exposure of polycrystalline Zn-doped TF-VLS InP to a hydrogen plasma (in the following referred to as hydrogenation) results in improved optoelectronic quality as well as lateral optoelectronic uniformity. A combination of low temperature photoluminescence and transient photocurrent spectroscopy was used to analyze the energy position and relative density of defect states before and after hydrogenation. Notably, hydrogenation reduces the relative intragap defect density by 1 order of magnitude. As a metric to monitor lateral optoelectronic uniformity of polycrystalline TF-VLS InP, photoluminescence and electron beam induced current mapping reveal homogenization of the grain versus grain boundary upon hydrogenation. At the device level, we measured more than 260 TF-VLS InP solar cells before and after hydrogenation to verify the improved optoelectronic properties. Hydrogenation increased the average open-circuit voltage (VOC) of individual TF-VLS InP solar cells by up to 130 mV and reduced the variance in VOC for the analyzed devices.

By employing graphene quantum dots (GQDs), we have achieved a high efficiency of 16.55% in n-type Si heterojunction solar cells. The efficiency enhancement is based on the photon downconversion phenomenon of GQDs to make more photons absorbed in the depletion region for effective carrier separation, leading to the enhanced photovoltaic effect. The short circuit current and the fill factor are increased from 35.31 to 37.47 mA/cm(2) and 70.29% to 72.51%, respectively. The work demonstrated here holds the promise for incorporating graphene-based materials in commercially available solar devices for developing ultrahigh efficiency photovoltaic cells in the future.

An advanced light-fidelity (Li-Fi) system based on the blue Gallium nitride (GaN) laser diode (LD) with a compact white-light phosphorous diffuser is demonstrated for fusing the indoor white-lighting and visible light communication (VLC). The phosphorous diffuser adhered blue GaN LD broadens luminescent spectrum and diverges beam spot to provide ample functionality including the completeness of Li-Fi feature and the quality of white-lighting. The phosphorous diffuser diverged white-light spot covers a radiant angle up to 120(o) with CIE coordinates of (0.34, 0.37). On the other hand, the degradation on throughput frequency response of the blue LD is mainly attributed to the self-feedback caused by the reflection from the phosphor-air interface. It represents the current state-of-the-art performance on carrying 5.2-Gbit/s orthogonal frequency-division multiplexed 16-quadrature-amplitude modulation (16-QAM OFDM) data with a bit error rate (BER) of 3.1 × 10(-3) over a 60-cm free-space link. This work aims to explore the plausibility of the phosphorous diffuser diverged blue GaN LD for future hybrid white-lighting and VLC systems.

The field of next‐generation microdisplays is flourishing. Relevant display technologies, such as mini‐light emission diodes (mini‐LEDs), micro‐organic light emission diodes (micro‐OLEDs), and micro‐light emission diodes (micro‐LEDs) are thus in the urgent stage of development. From this perspective, comprehensive and systematical analyzes are conducted for the aforesaid microdisplay configurations. A holistic view of microdisplay technologies is developed with the corresponding performance metrics, providing a path for miscellaneous scenarios. Among these scenarios, the applications in augmented reality (AR), virtual reality (VR), wearable devices, and head‐up displays (HUD) are currently attracting considerable attention for deeper human‐digital interactions. However, there is a multiplicity of obstacles and challenges hindering such development. Nevertheless, recent advances in microdisplay technologies hold tremendous promise for the paradigms of these applications, taking a leap forward for next‐generation microdisplays. This review presents perspectives, relevant materials, and the technology landscape for such ongoing display technologies, offering guidance on the design of advanced microdisplays. [ABSTRACT FROM AUTHOR]

Aluminum Gallium Nitride (AlGaN) ultraviolet‐C (UV‐C) micro‐light‐emitting diodes (microLEDs) offer significant advantages in terms of convenience, cost‐effectiveness, and environmental friendliness, positioning them as promising candidates for display applications. However, achieving the desired high efficiency and scalability for large displays with ultra‐fine pixels necessitates substantial progress beyond current experimental outcomes. This study showcases the application of AlGaN UV‐C microLED display panels and micro‐displays incorporating quantum dots (QDs) for color conversion. Sidewall treatment and atomic layer deposited (ALD) passivation effectively address dangling bonds and etching damages, leading to a notable enhancement of TM‐polarized light extraction efficiency (LEE). Moreover, dedicated strain modulation efforts successfully reduce the high Al content (over 50%) wafer bowling effect, facilitating the modularization of ultrafine‐pitch AlGaN UV‐C microLED panels. Consequently, the devices achieve a peak performance of over 5% external quantum efficiency (EQE) as the mesa size scales down to 3 μm. The highlighted 0.18‐inch UV‐C microLED display panels, featuring a 9 μm pixel size, are precisely controlled by a CMOS IC driver to achieve desired patterns. Serving as an efficient pumping source for perovskite quantum dots paper (PQDP), this UV‐C microLED display suggests the potential to revolutionize the full‐color display industry by providing an innovative and unconventional solution. [ABSTRACT FROM AUTHOR]