Search

Velocity sensitivity refers to the possibility and degree of reservoir permeability decline caused by the migration of various particles in the reservoir rock due to the increase in fluid flow velocity and the blockage of pore channels. To improve the development results of M reservoir in Karamay Oil field, two reservoir cores were selected to carry out velocity sensitivity experiments. The permeability of No. 1 core decreases obviously when the flow rate is greater than 0.04 mL/min. Therefore, it can be considered that the injection rate of velocity sensitivity is between 0.04 and 0.06 mL/min, and the displacement rate should be less than 0.04 mL/min in the core displacement experiment. When the flow rate is greater than 0.5 mL/min, the permeability of No. 2 core decreases significantly. This is mainly due to the high permeability and critical velocity of No. 2 core. The study can provide a basis for the selection of displacement velocity in core displacement experiments, and also provide a reference for the determination of reasonable injection-production velocity in actual production.

The great difference in density between steam and liquid during wet steam injection always results in steam override, that is, steam gathers on the top of the pay zone. In this article, the equation for steam override coefficient was firstly established based on van Lookeren’s steam override theory and then radius of steam zone and hot fluid zone were derived according to a more realistic temperature distribution and an energy balance in the pay zone. On this basis, the equation for the reservoir heat efficiency with the consideration of steam override was developed. Next, predicted results of the new model were compared with these of another analytical model and CMG STARS (a mature commercial reservoir numerical simulator) to verify the accuracy of the new mathematical model. Finally, based on the validated model, we analyzed the effects of injection rate, steam quality and reservoir thickness on the reservoir heat efficiency. The results show that the new model can be simplified to the classic model (Marx-Langenheim model) under the condition of the steam override being not taken into account, which means the Marx-Langenheim model is corresponding to a special case of this new model. The new model is much closer to the actual situation compared to the Marx-Langenheim model because of considering steam override. Moreover, with the help of the new model, it is found that the reservoir heat efficiency is not much affected by injection rate and steam quality but significantly influenced by reservoir thickness, and to ensure that the reservoir can be heated effectively, the reservoir thickness should not be too small.

Worldwide practices have proven that gas-assisted gravity drainage can obviously enhance oil recovery, and this technology can be especially effective for reservoirs with a thick formation and large inclination angle. For the successful implementation of this process, a key technology is the stable control of gas–oil interface during gas injection. For a detailed exploration of this technique, a three-stage permeable visual model was designed and manufactured, with permeability decreasing from top to bottom, thus, a reverse rhythm reservoir was effectively modeled. Then the experiment concerning CO2-assisted gravity drainage was carried out with the adoption of a self-developed micro visual displacement device. This study mainly focused on the micro migration law of gas–oil interface and the development effects of CO2-assisted gravity drainage. According to the experiments, CO2 fingering somewhat happens in the same permeable layer from the beginning of gas injection. However, phenomena of "wait" and "gas–oil interface self-adjustment" occur instead of flowing into the next layer when the injected CO2 reaches the boundary of the next lower permeability layer through the dominant channel. By the "gas–oil interface self-adjustment", the injected CO2 first enters into the pores of the relative higher permeability layer to the greatest extent, and thus expands the sweep volume. Futhermore, in the process of CO2 injection, obvious gas channeling occurs in the low permeability layer directly connected to the outlet, resulting in low sweep efficiency and poor development effect. After connecting the core with lower permeability at the outlet, the development indexes of the model, such as the producing degree of the low permeability layer, the oil recovery before and after gas breakthrough, are significantly improved, and the recovery degrees of the medium permeability layer and the high permeability layer are also improved, and the overall recovery factor is increased by 12.38%. This "gas–oil interface self-adjustment" phenomenon is explained reasonably from the two scales of macroscopic flow resistance and microscopic capillary force. Finally, the enlightenments of the new phenomenon are expounded on the application of gas-assisted gravity drainage on site and the treatment of producers with gas breakthrough in gas injection development. [ABSTRACT FROM AUTHOR]

On purpose of studying the regulations and prediction methods of volume expansion of CO 2 + crude oil, eleven hydrocarbon components were selected to represent crude oil. Then, Constant Component Expansion (CCE) experiments were carried out with the hydrocarbon components and different molar fractions of CO 2 . According to the results, it was obviously that hydrocarbon components could expand the volume because of mixing the CO 2 . However, the expansion degree was largely influenced by the hydrocarbon properties. Therefore, a new parameter named the molar density was proposed to characterize these influences. The study found that hydrocarbon swelling factor and molar density were strict linear relationship. Based on this regulation and additional theoretical derivation, a prediction model was established to calculating volume expansion degree of CO 2 + crude oil. With the experimental results of reservoir oil from CQ oilfield, it was turned out that the prediction model could successfully and precisely calculate crude oil swelling degree. [ABSTRACT FROM AUTHOR]