Search

Recycling of hydrogen gas (H 2 ) produced at the cathode to the anode in an electrochemical system allows for energy efficient TAN (Total Ammonia Nitrogen) recovery. Using a H 2 recycling electrochemical system (HRES) we achieved high TAN transport rates at low energy input. At a current density of 20 A m -2 , TAN removal rate from the influent was 151 g N m -2 d -1 at an energy demand of 26.1 kJ g N -1 . The maximum TAN transport rate of 335 g N m -2 d -1 was achieved at a current density of 50 A m -2 and an energy demand of 56.3 kJ g N -1 . High TAN removal efficiency (73-82%) and recovery (60-73%) were reached in all experiments. Therefore, our HRES is a promising alternative for electrochemical and bioelectrochemical TAN recovery. Advantages are the lower energy input and lower risk of chloride oxidation compared to electrochemical technologies and high rates and independence of organic matter compared to bioelectrochemical systems.

Combining two solutions of different composition releases the Gibbs free energy of mixing. By using engineered processes to control the mixing, chemical energy stored in salinity gradients can be harnessed for useful work. In this critical review, we present an overview of the current progress in salinity gradient power generation, discuss the prospects and challenges of the foremost technologies - pressure retarded osmosis (PRO), reverse electrodialysis (RED), and capacitive mixing (CapMix) and provide perspectives on the outlook of salinity gradient power generation. Momentous strides have been made in technical development of salinity gradient technologies and field demonstrations with natural and anthropogenic salinity gradients (for example, seawater-river water and desalination brine-wastewater, respectively), but fouling persists to be a pivotal operational challenge that can significantly ebb away cost-competitiveness. Natural hypersaline sources (e.g., hypersaline lakes and salt domes) can achieve greater concentration difference and, thus, offer opportunities to overcome some of the limitations inherent to seawater-river water. Technological advances needed to fully exploit the larger salinity gradients are identified. While seawater desalination brine is a seemingly attractive high salinity anthropogenic stream that is otherwise wasted, actual feasibility hinges on the appropriate pairing with a suitable low salinity stream. Engineered solutions are foulant-free and can be thermally regenerative for application in low-temperature heat utilization. Alternatively, PRO, RED, and CapMix can be coupled with their analog separation process (reverse osmosis, electrodialysis, and capacitive deionization, respectively) in salinity gradient flow batteries for energy storage in chemical potential of the engineered solutions. Rigorous techno-economic assessments can more clearly identify the prospects of low-grade heat conversion and large-scale energy storage. While research attention is squarely focused on efficiency and power improvements, efforts to mitigate fouling and lower membrane and electrode cost will be equally important to reduce levelized cost of salinity gradient energy production and, thus, boost PRO, RED, and CapMix power generation to be competitive with other renewable technologies. Cognizance of the recent key developments and technical progress on the different technological fronts can help steer the strategic advancement of salinity gradient as a sustainable energy source.

We revisit Morrison and Osterle (1965) who derived a phenomenological expression for the 'figure-of-merit' [Formula: see text] of the electrokinetic energy conversion (EKEC) of a pressure difference into electric energy (and vice versa) using charged nanotubes, nanopores or ion-exchange membranes. We show the equivalence with Morrison and Osterle of a novel expression of [Formula: see text] derived by Bentien et al (2013). We analyze two physical models for ionic and solvent flow which directly relate [Formula: see text] to nanopore characteristics such as pore size and wall charge density. For the uniform potential model, we derive an analytical expression as a function of pore size, viscosity, ion diffusion coefficients and membrane charge density, and compare results with the full space-charge model by Osterle and co-workers as a function of pore size and ion diffusion coefficient. We present a novel expression for [Formula: see text] for salt solutions with ions with unequal diffusion coefficients (mobilities) and show that to increase [Formula: see text] the counterion mobility must be low and the coion mobility high.

Chain elongation into medium-chain carboxylates, such as n-caproate and n-caprylate, with ethanol as an electron donor and with open cultures of microbial consortia (i.e., reactor microbiomes) under anaerobic conditions is being developed as a biotechnological production platform. The goal is to use the high thermodynamic efficiency of anaerobic fermentation to convert organic biomass or organic wastes into valuable biochemicals that can be extracted. Several liter-scale studies have been completed and a first pilot-plant study is underway. However, the underlying microbial pathways are not always well understood. In addition, an interdisciplinary approach with knowledge from fields ranging from microbiology and chemical separations to biochemistry and environmental engineering is required. To bring together research from different fields, we reviewed the literature starting with the microbiology and ending with the bioprocess engineering studies that already have been performed. Because understanding the microbial pathways is so important to predict and steer performance, we delved into a stoichiometric and thermodynamic model that sheds light on the effect of substrate ratios and environmental conditions on product formation. Finally, we ended with an outlook.

A model is presented for the process of harvesting electrical energy from CO2 emissions using capacitive cells. The principle consists of controlling the mixing process of a concentrated CO2 gas stream with a dilute CO2 gas stream (as, for example, exhaust gas and air), thereby converting part of the released mixing energy into electrical energy. The model describes the transient reactive transport of CO2 gas absorbed in water or in monoethanolamine (MEA) solutions, under the assumption of local chemical equilibrium. The model combines the selective transport of ions through ion-exchange membranes, the accumulation of charge in the porous carbon electrodes and the coupling between the ionic current and the produced electrical current and power. We demonstrate that the model can be used to calculate the energy that can be extracted by mixing concentrated and dilute CO2 containing gas streams. Our calculation results for the process using MEA solutions have various counterintuitive features, including: 1. When dynamic equilibrium is reached in the cyclical process, the electrical charge in the anode is negative both during charging and discharging; 2. Placing an anion-exchange membrane (AEM) in the system is not required, the energy per cycle is just as large with or without an AEM., (Copyright © 2014 Elsevier Inc. All rights reserved.)

The use of granular electrodes in Microbial Fuel Cells (MFCs) is attractive because granules provide a cost-effective way to create a high electrode surface area, which is essential to achieve high current and power densities. Here, we show a novel reactor design based on capacitive granules: the fluidized capacitive bioanode. Activated carbon (AC) granules are colonized by electrochemically active microorganisms, which extract electrons from acetate and store the electrons in the granule. Electricity is harvested from the AC granules in an external discharge cell. We show a proof-of-principle of the fluidized capacitive system with a total anode volume of 2 L. After a start-up period of 100 days, the current increased from 0.56 A/m(2) with 100 g AC granules, to 0.99 A/m(2) with 150 g AC granules, to 1.3 A/m(2) with 200 g AC granules. Contact between moving AC granules and current collector was confirmed in a control experiment without biofilm. Contribution of an electro-active biofilm to the current density with recirculation of AC granules was limited. SEM images confirmed that a biofilm was present on the AC granules after operation in the fluidized capacitive system. Although current densities reported here need further improvement, the high surface area of the AC granules in combination with external discharge offers new and promising opportunities for scaling up MFCs.

Recently, a new technology has been proposed for the utilization of energy from CO2 emissions (Hamelers et al., 2014). The principle consists of controlling the dilution process of CO2-concentrated gas (e.g., exhaust gas) into CO2-dilute gas (e.g., air) thereby extracting a fraction of the released mixing energy. In this paper, we describe the theoretical fundamentals of this technology when using a pair of charge-selective capacitive electrodes. We focus on the behavior of the chemical system consisting of CO2 gas dissolved in water or monoethanolamine solution. The maximum voltage given for the capacitive cell is theoretically calculated, based on the membrane potential. The different aspects that affect this theoretical maximum value are discussed., (Copyright © 2013 Elsevier Inc. All rights reserved.)

Heptanoate (or enanthate), a saturated mono-carboxylate with seven carbon atoms, is a commercially produced biochemical building block with versatile applications. Currently, heptanoate is mainly derived from the oxidation of heptaldehyde, which can be obtained after pyrolysis of castor oil. The objective of this investigation was to achieve efficient high rate heptanoate production using a mixed culture chain elongation process based on propionate and ethanol. An efficient high rate heptanoate production using chain elongation could offer an alternative for heptanoate production from castor oil. The investigation was performed in an upflow anaerobic filter with a hydraulic retention time of 17 h. A heptanoate production rate of 4.5 g l(-1) d(-1) was achieved with a heptanoate concentration of 3.2 g l(-1). These results show sufficient potential to consider this approach as an alternative for heptanoate production from castor oil. Future research should make heptanoate production from propionate and ethanol more cost-effective., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

This research demonstrated the selective production of n-butyrate from mixed culture by applying 2 bar carbon dioxide into the headspace of batch fermenters or by increasing the initial substrate concentration. The effect of increasing initial substrate concentration was investigated at 8, 13.5 and 23 g COD/L with potato processing waste stream. Within 1 week of incubation, n-butyrate fraction selectively increased up to 83% by applying 2 bar hydrogen or 78% by applying carbon dioxide into the headspace whereas it was only 59% in the control reactor. Although the fraction of n-butyrate was elevated, the concentration remained lower than in the control. Both the highest concentration and fraction of n-butyrate were observed under the highest initial substrate concentration without headspace addition. The concentration was 10 g COD/L with 73% fraction. The operational conditions obtained from batch experiments for selective n-butyrate production were validated in a continuous process., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

The objective of this investigation was to further increase the medium chain fatty acid (MCFA) production rate by reducing the hydraulic retention time (HRT) in an upflow anaerobic filter. The results showed that the volumetric MCFA production rate was increased to 57.4 g MCFA l(-1) d(-1), more than 3 times higher than previous work. Despite the lower MCFA concentrations at 4h HRT, the MCFA selectivity remained above 80%. Extra carbon dioxide additions and higher yeast extract concentrations were required to increase the MCFA production rate. More research related to substrates and (micro)nutrients in mixed culture continuous reactors needs to be performed to reduce yeast extract use in chain elongation., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

Recently, interest has regained for medium chain fatty acids (MCFAs) as a low cost feedstock for bio-based chemical and fuel production processes. To become cost-effective, the volumetric MCFA production rate by chain elongation should increase to comparable rates of other fermentation processes. We investigate the MCFA production process at a hydraulic retention time of 17 h in an upflow anaerobic filter to improve the volumetric MCFA production rate. This approach resulted in a MCFA production with a volumetric production rate of 16.6 g l(-1) d(-1), which is more than seven times higher than the current production rate. Moreover the rate is now in the range of other fermentation processes like methane, butanol and ethanol production. Increasing the ethanol load lead to higher volumetric production rates and a high MCFA selectivity of 91%. During operation, methane percentages lower than 0.1% were detected in the headspace of reactor., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Energy extraction based on capacitive Donnan potential (CDP) is a recently suggested technique for sustainable power generation. CDP combines the use of ion-exchange membranes and porous carbon electrodes to convert the Gibbs free energy of mixing sea and river water into electric work. The electrodes geometry has a relevant impact on internal resistance and overall performance in CDP. In this work, we present the first effort to use wire-shaped electrodes and its suitability for improving CDP. Analytical evaluation and electrical measurements confirm a strong nonlinear decrease in internal resistance for distances between electrodes smaller than 3 mm. We also demonstrated that we get more power per material invested when compared to traditional flat plate designs. These findings show the advantages of this design for further development of CDP into a mature technology.

Due to a growing world population and increasing welfare, energy demand worldwide is increasing. To meet the increasing energy demand in a sustainable way, new technologies are needed. The Plant-Microbial Fuel Cell (P-MFC) is a technology that could produce sustainable bio-electricity and help meeting the increasing energy demand. Power output of the P-MFC, however, needs to be increased to make it attractive as a renewable and sustainable energy source. To increase power output of the P-MFC internal resistances need to be reduced. With a flat-plate P-MFC design we tried to minimize internal resistances compared to the previously used tubular P-MFC design. With the flat-plate design current and power density per geometric planting area were increased (from 0.15 A/m2 to 1.6 A/m2 and from 0.22 W/m2 to and 0.44 W/m2)as were current and power output per volume (from 7.5 A/m3 to 122 A/m3 and from 1.3 W/m3 to 5.8 W/m3). Internal resistances times volume were decreased, even though internal resistances times membrane surface area were not. Since the membrane in the flat-plate design is placed vertically, membrane surface area per geometric planting area is increased, which allows for lower internal resistances times volume while not decreasing internal resistances times membrane surface area. Anode was split into three different sections on different depths of the system, allowing to calculate internal resistances on different depths. Most electricity was produced where internal resistances were lowest and where most roots were present; in the top section of the system. By measuring electricity production on different depths in the system, electricity production could be linked to root growth. This link offers opportunities for material-reduction in new designs. Concurrent reduction in material use and increase in power output brings the P-MFC a step closer to usable energy density and economic feasibility.

This study investigated the carboxylate spectrum from mixed culture fermentation of three organic waste streams after supplying 2 bar hydrogen and carbon dioxide or a mixture of these two gases to the headspace. Under any modified headspace, propionate production was ceased and butyrate, caproate and the total carboxylate concentrations were higher than in the reactors with N(2) headspace (control). Production of one major compound was achieved under hydrogen and carbon dioxide mixed headspace after 4 weeks of incubation. Both the highest acetate concentration (17.4 g COD/l) and the highest fraction (87%) were observed in reactors with mixed hydrogen and carbon dioxide headspace independent of the substrate used. In the control reactor, acetate made up maximum 67% of the total products. For other products, the highest concentration and fraction were seldom observed together. Selective butyrate production reaching a 75% fraction was found under the carbon dioxide headspace on the carbohydrate rich waste., (Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.)

Polarization curves are of paramount importance for the detection of toxic components in microbial fuel cell (MFC) based biosensors. In this study, polarization curves were made under non-toxic conditions and under toxic conditions after the addition of various concentrations of nickel, bentazon, sodiumdodecyl sulfate and potassium ferricyanide. The experimental polarization curves show that toxic components have an effect on the electrochemically active bacteria in the cell. (Extended) Butler Volmer Monod (BVM) models were used to describe the polarization curves of the MFC under nontoxic and toxic conditions. It was possible to properly fit the (extended) BVM models using linear regression techniques to the polarization curves and to distinguish between different types of kinetic inhibitions. For each of the toxic components, the value of the kinetic inhibition constant Ki was also estimated from the experimental data. The value of Ki indicates the sensitivity of the sensor for a specific component and thus can be used for the selection of the biosensor for a toxic component.

We show the significant potential of water desalination using a novel capacitive wire-based technology in which anode/cathode wire pairs are constructed from coating a thin porous carbon electrode layer on top of electrically conducting rods (or wires). By alternately dipping an array of electrode pairs in freshwater with and in brine without an applied cell voltage, we create an ion adsorption/desorption cycle. We show experimentally how in six subsequent cycles we can reduce the salinity of 20 mM feed (brackish) water by a factor of 3, while application of a cation exchange membrane on the cathode wires makes the desalination factor increase to 4. Theoretical modeling rationalizes the experimental findings, and predicts that system performance can be significantly enhanced by material modifications. To treat large volumes of water, multiple stacks of wire pairs can be used simultaneously in a "merry-go-round" operational mode.

Bioelectrochemical systems (BESs) hold great promise for sustainable production of energy and chemicals. This review addresses the factors that are essential for practical application of BESs. First, we compare benefits (value of products and cleaning of wastewater) with costs (capital and operational costs). Based on this, we analyze the maximum internal resistance (in mΩ m(2) ) and current density that is required to make microbial fuel cells (MFCs) and hydrogen-producing microbial electrolysis cells (MECs) cost effective. We compare these maximum resistances to reported internal resistances and current densities with special focus on cathodic resistances. Whereas the current densities of MFCs still need to be increased considerably (i.e., internal resistance needs to be decreased), MECs are closer to application as their current densities can be increased by increasing the applied voltage. For MFCs, the production of high-value products in combination with electricity production and wastewater treatment is a promising route., (Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Nitrogen recovery through NH(3) stripping is energy intensive and requires large amounts of chemicals. Therefore, a microbial fuel cell was developed to simultaneously produce energy and recover ammonium. The applied microbial fuel cell used a gas diffusion cathode. The ammonium transport to the cathode occurred due to migration of ammonium and diffusion of ammonia. In the cathode chamber ionic ammonium was converted to volatile ammonia due to the high pH. Ammonia was recovered from the liquid-gas boundary via volatilization and subsequent absorption into an acid solution. An ammonium recovery rate of 3.29 g(N) d(-1) m(-2) (vs. membrane surface area) was achieved at a current density of 0.50 A m(-2) (vs. membrane surface area). The energy balance showed a surplus of energy 3.46 kJ g(N)(-1), which means more energy was produced than needed for the ammonium recovery. Hence, ammonium recovery and simultaneous energy production from urine was proven possible by this novel approach., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

We developed an integrated system for storage of renewable electricity in a microbial fuel cell (MFC). The system contained a capacitive electrode that was inserted into the anodic compartment of an MFC to form a capacitive bioanode. This capacitive bioanode was compared with a noncapacitive bioanode on the basis of performance and storage capacity. The performance and storage capacity were investigated during polarization curves and charge-discharge experiments. During polarization curves the capacitive electrode reached a maximum current density of 1.02 ± 0.04 A/m(2), whereas the noncapacitive electrode reached a current density output of only 0.79 ± 0.03 A/m(2). During the charge-discharge experiment with 5 min of charging and 20 min of discharging, the capacitive electrode was able to store a total of 22,831 C/m(2), whereas the noncapacitive electrode was only able to store 12,195 C/m(2). Regarding the charge recovery of each electrode, the capacitive electrode was able to recover 52.9% more charge during each charge-discharge experiment compared with the noncapacitive electrode. The capacitive electrode outperformed the noncapacitive electrode throughout each charge-discharge experiment. With a capacitive electrode it is possible to use the MFC simultaneously for production and storage of renewable electricity.

In this paper, the effect of root oxygen loss on energy recovery of the plant microbial fuel cell (PMFC) is described. In this manner, advanced understanding of competing processes within the rhizosphere-anode interface was provided. A microscopic model was developed on the basis of exudation, oxygen loss, biological oxidation, and biological current generation. The model was successfully validated by comparison to oxygen concentration profiles, volatile fatty acid profiles, and chemical oxygen demand profiles measured in the anode compartment. The model predicted oxic zones around roots in the anode of the plant microbial fuel cell. Results show no direct link between current generation and photosynthesis. This was consistent with the model which predicted that current was generated via hydrolysis of root-derived organic compounds. This result means that to optimize energy recovery of a PMFC, the plant selection should focus on high root biomass production combined with low oxygen loss., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

H(2) can be produced from organic matter with a microbial electrolysis cell (MEC). To decrease MEC capital costs, a cathode is needed that is made of low-cost material and produces H(2) at high rate. A microbial biocathode is a low-cost candidate, but suffers from a long startup and a low H(2) production rate. In this study, the effects of cathode potential and carbon source on microbial biocathode startup were investigated. Application of a more negative cathode potential did not decrease the startup time of the biocathode. If acetate instead of bicarbonate was used as carbon source, the biocathode started up more than two times faster. The faster startup was likely caused by a higher biomass yield for acetate than for bicarbonate, which was supported by thermodynamic calculations. To increase the H(2) production rate, a flow through biocathode fed with acetate was investigated. This biocathode produced 2.2 m(3) H(2) m(-3)  reactor day(-1) at a cathode potential of -0.7 V versus NHE, which was seven times that of a parallel flow biocathode of a previous study., (Copyright © 2011 Wiley Periodicals, Inc.)

In a Plant-Microbial Fuel Cell anode-conditions must be created that are favorable for plant growth and electricity production. One of the major aspects in this is the composition of the plant-growth medium. Hoagland medium has been used until now, with added phosphate buffer to reduce potential losses over the membrane because of differences in pH between anode and cathode. We developed a new, improved plant-growth medium that improves current production, while the plant keeps growing. This medium is a nitrate-less, ammonium-rich medium that contains all macro- and micro-nutrients necessary for plant growth, with a balanced amount of bicarbonate buffer. Sulphate presence in the plant-growth medium helps to keep a low anode-potential. With the new plant-growth medium the maximum current production of the Plant-Microbial Fuel Cell increased from 186 mA/m(2) to 469 mA/m(2)., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

To create an efficient bioelectrochemical system, a high Coulombic efficiency is required. This efficiency is a direct measure for the competition between electrogens and methanogens when acetate is used as substrate. In this study the Coulombic efficiency in a microbial electrolysis cell was investigated. As a result of an increase in substrate concentration from 1 to 35 mM, the current density increased to 21.1A/m(2), while the Coulombic efficiency decreased to 52%. As a result of an increase in anode potential from -450 to -0.250 mV, the current density increased to 20.9A/m(2), while the Coulombic efficiency increased 21%. Knowledge about the substrate affinity and growth kinetics is crucial to control the Coulombic efficiency. Further research is required to optimize strategies to find a balance between the Coulombic efficiency, current density and removal rate of organic material., (Copyright © 2011 Elsevier Ltd. All rights reserved.)

Currently available models describing microbial fuel cell (MFC) polarization curves, do not describe the effect of the presence of toxic components. A bioelectrochemical model combined with enzyme inhibition kinetics, that describes the polarization curve of an MFC-based biosensor, was modified to describe four types of toxicity. To get a stable and sensitive sensor, the overpotential has to be controlled. Simulations with the four modified models were performed to predict the overpotential that gives the most sensitive sensor. These simulations were based on data and parameter values from experimental results under non-toxic conditions. Given the parameter values from experimental results, controlling the overpotential at 250 mV leads to a sensor that is most sensitive to components that influence the whole bacterial metabolism or that influence the substrate affinity constant (Km). Controlling the overpotential at 105 mV is the most sensitive setting for components influencing the ratio of biochemical over electrochemical reaction rate constants (K1), while an overpotential of 76 mV gives the most sensitive setting for components that influence the ratio of the forward over backward biochemical rate constants (K2). The sensitivity of the biosensor was also analyzed for robustness against changes in the model parameters other than toxicity. As an example, the tradeoff between sensitivity and robustness for the model describing changes on K1 (IK1) is presented. The biosensor is sensitive for toxic components and robust for changes in model parameter K2 when overpotential is controlled between 118 and 140 mV under the simulated conditions., (Copyright © 2010 Elsevier B.V. All rights reserved.)

Ammonium recovery using a two chamber microbial fuel cell (MFC) was investigated at high ammonium concentration. Increasing the ammonium concentration (from 0.07 to 4 g ammonium-nitrogen/L) by addition of ammonium chloride did not affect the performance of the MFC. The obtained current densities by DC-voltammetry were higher than 6A/m(2) for both operated MFCs. Also continuous operation at lower external resistance (250 Ω) showed an increased current density (0.9A/m(2)). Effective ammonium recovery can be achieved by migrational ion flux through the cation exchange membrane to the cathode chamber, driven by the electron production from degradation of organic substrate. The charge transport was proportional to the concentration of ions. Nonetheless, a concentration gradient will influence the charge transport. Furthermore, a charge exchange process can influence the charge transport and therefore the recovery of specific ions., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

Four types of titanium (Ti)-based electrodes were tested in the same microbial fuel cell (MFC) anodic compartment. Their electrochemical performances and the dominant microbial communities of the electrode biofilms were compared. The electrodes were identical in shape, macroscopic surface area, and core material but differed in either surface coating (Pt- or Ta-coated metal composites) or surface texture (smooth or rough). The MFC was inoculated with electrochemically active, neutrophilic microorganisms that had been enriched in the anodic compartments of acetate-fed MFCs over a period of 4 years. The original inoculum consisted of bioreactor sludge samples amended with Geobacter sulfurreducens strain PCA. Overall, the Pt- and Ta-coated Ti bioanodes (electrode-biofilm association) showed higher current production than the uncoated Ti bioanodes. Analyses of extracted DNA of the anodic liquid and the Pt- and Ta-coated Ti electrode biofilms indicated differences in the dominant bacterial communities. Biofilm formation on the uncoated electrodes was poor and insufficient for further analyses. Bioanode samples from the Pt- and Ta-coated Ti electrodes incubated with Fe(III) and acetate showed several Fe(III)-reducing bacteria, of which selected species were dominant, on the surface of the electrodes. In contrast, nitrate-enriched samples showed less diversity, and the enriched strains were not dominant on the electrode surface. Isolated Fe(III)-reducing strains were phylogenetically related, but not all identical, to Geobacter sulfurreducens strain PCA. Other bacterial species were also detected in the system, such as a Propionicimonas-related species that was dominant in the anodic liquid and Pseudomonas-, Clostridium-, Desulfovibrio-, Azospira-, and Aeromonas-related species.

Microbial solar cells (MSCs) are recently developed technologies that utilize solar energy to produce electricity or chemicals. MSCs use photoautotrophic microorganisms or higher plants to harvest solar energy, and use electrochemically active microorganisms in the bioelectrochemical system to generate electrical current. Here, we review the principles and performance of various MSCs in an effort to identify the most promising systems, as well as the bottlenecks and potential solutions, for "real-life" MSC applications. We present an outlook on future applications based on the intrinsic advantages of MSCs, specifically highlighting how these living energy systems can facilitate the development of an electricity-producing green roof., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

A kinetic model of the bio-anode was developed based on a simple representation of the underlying biochemical conversions as described by enzyme kinetics, and electron transfer reactions as described by the Butler-Volmer electron transfer kinetics. This Butler-Volmer-Monod model was well able to describe the measured bio-anode polarization curves. The Butler-Volmer-Monod model was compared to the Nernst-Monod model described the experimental data significantly better. The Butler-Volmer-Monod model has the Nernst-Monod model as its full electrochemically reversible limit. Contrary to the Nernst-Monod model, the Butler-Volmer-Monod model predicts zero current at equilibrium potential. Besides, the Butler-Volmer-Monod model predicts that the apparent Monod constant is dependent on anode potential, which was supported by experimental results., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

The use of porous electrodes like graphite felt as anode material has the potential of achieving high volumetric current densities. High volumetric current densities, however, may also lead to mass transport limitations within these porous materials. Therefore, in this study we investigated the mass and charge transport limitations by increasing the speed of the forced flow and changing the flow direction through the porous anode. Increase of the flow speed led to a decrease in current density when the flow was directed towards the membrane caused by an increase in anode resistance. Current density increased at higher flow speed when the flow was directed away from the membrane. This was caused by a decrease in transport resistance of ions through the membrane which increased the buffering effect of the system. Furthermore, the increase in flow speed led to an increase of the coulombic efficiency by 306%., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

Low pH buffer capacity of waste streams limits further development of bioelectrochemical systems (BES) because accumulation of protons potentially leads to acidification of the anodic biofilm. Here we introduce a system that makes it possible to recover alkalinity in an extra recovery compartment. The system consisted of this extra compartment which was located between anode and cathode compartment. The compartment was separated from the anode by a cation exchange membrane and from the cathode by an anion exchange membrane, which made clean hydrogen production possible. To compensate for the charge movement as a result of the flow of electrons, both cations and hydroxyl ions moved into the new recovery compartment. When a synthetic waste stream was fed through this recovery compartment, both pH and conductivity increased. When this stream is then fed to the anode of the BES, no additional buffer was required to produce the same current (3.5 A/m(2)) at an applied voltage of 1 V.

The main limiting factor in Microbial Fuel Cell (MFC) power output is the cathode, because of the high overpotential for oxygen reduction. Oxygen reducing biocathodes can decrease this overpotential by the use of microorganisms as a catalyst. In this study, we investigated the factors limiting biocathode performance. Three biocathodes were started up at different cathode potentials, and their performance and catalytic behavior was tested by means of polarization curves and cyclic voltammetry. The biocathodes controlled at +0.05 V and +0.15 V vs Ag/AgCl produced current almost immediately after inoculation, while the biocathode controlled at +0.25 V vs Ag/AgCl produced no current until day 15. The biocathode controlled at +0.15 V vs Ag/AgCl reached the highest current density of 313 mA/m(2). Cyclic voltammetry showed clear catalysis for all three biocathodes. The biocathodes were limited by both mass transfer of oxygen and by charge transfer. Mass transfer calculations show that the transfer of oxygen poses a serious limitation for the use of dissolved oxygen as an electron acceptor in MFCs.

The entropy increase of mixing two solutions of different salt concentrations can be harnessed to generate electrical energy. Worldwide, the potential of this resource, the controlled mixing of river and seawater, is enormous, but existing conversion technologies are still complex and expensive. Here we present a small-scale device that directly generates electrical power from the sequential flow of fresh and saline water, without the need for auxiliary processes or converters. The device consists of a sandwich of porous "supercapacitor" electrodes, ion-exchange membranes, and a spacer and can be further miniaturized or scaled-out. Our results demonstrate that alternating the flow of saline and fresh water through a capacitive cell allows direct autogeneration of voltage and current and consequently leads to power generation. Theoretical calculations aid in providing directions for further optimization of the properties of membranes and electrodes.

A metallurgical microbial fuel cell (MFC) is an attractive alternative for recovery of copper from copper containing waste streams, as the metal is recovered in its metallic form at the cathode, while the energy for metal reduction can be obtained from oxidation of organic materials at the anode with possible additional production of electricity. We studied the recovery of copper in an MFC using a bipolar membrane as a pH separator. Under anaerobic conditions, the maximum power density was 0.43 W/m(2) at a current density of 1.7 A/m(2). In the presence of oxygen, MFC performance improved considerably to a maximum power density of 0.80 W/m(2) at a current density of 3.2 A/m(2). Pure copper crystals were formed on the cathode, and no CuO or Cu(2)O was detected. Removal efficiencies of >99.88% were obtained. The cathodic recovery of copper compared to the produced electricity was 84% (anaerobic) and 43% (aerobic). The metallurgy MFC with the Cu(2+) reducing cathode further enlarges the application range of MFCs.

Anaerobic bacteria have the ability to produce electricity from the oxidation of organic substrates. They also may use electricity to support chemical reactions that are energetically unfavorable. In the fermentation of sugars, hydrogen can be formed as one of the main products. However, a yield of only four hydrogen per molecule of glucose can be achieved. Potentially, eight additional hydrogen molecules could be produced when the other main fermentation product acetate is converted further, which however is energetically not possible. By the input of electricity, acetate can be oxidized further to form hydrogen. This paper reviews the scarce knowledge of how electricity can be used to produce hydrogen in the microbial oxidation of acetate or other substrates. The technological design concepts and their performance are presented, and the biochemical mechanisms of electron transfer are discussed., (Copyright 2010 Elsevier Ltd. All rights reserved.)

In a Plant Microbial Fuel Cell (P-MFC) three plants were tested for concurrent biomass and bio-electricity production and maximization of power output. Spartina anglica and Arundinella anomala concurrently produced biomass and bio-electricity for six months consecutively. Average power production of the P-MFC with S. anglica during 13weeks was 16% of the theoretical maximum power and 8% during 7weeks for A. anomala. The P-MFC with Arundo donax, did not produce electricity with a stable output, due to break down of the system. The highest obtained power density in a P-MFC was 222mW/m(2) membrane surface area with S. anglica, over twice as high as the highest reported power density in a P-MFC. High biomass yields were obtained in all P-MFC's, with a high root:shoot ratio, probably caused nutrient availability and anaerobia in the soil. Power output maximization via adjusting load on the system lead to unstable performance of the P-MFC., (Copyright 2010 Elsevier Ltd. All rights reserved.)

The plant microbial fuel cell is a sustainable and renewable way of electricity production. The plant is integrated in the anode of the microbial fuel cell which consists of a bed of graphite granules. In the anode, organic compounds deposited by plant roots are oxidized by electrochemically active bacteria. In this research, salt marsh species Spartina anglica generated current for up to 119 days in a plant microbial fuel cell. Maximum power production was 100 mW m(-2) geometric anode area, highest reported power output for a plant microbial fuel cell. Cathode overpotential was the main potential loss in the period of oxygen reduction due to slow oxygen reduction kinetics at the cathode. Ferricyanide reduction improved the kinetics at the cathode and increased current generation with a maximum of 254%. In the period of ferricyanide reduction, the main potential loss was transport loss. This research shows potential application of microbial fuel cell technology in salt marshes for bio-energy production with the plant microbial fuel cell.

This study demonstrates, for the first time, the proof-of-principle of an MEC in which both the anodic and cathodic reaction are catalyzed by microorganisms. No expensive chemical catalysts, such as platinum, are needed. Two of these MECs were simultaneously operated and reached a maximum of 1.4 A/m(2) at an applied cell voltage of 0.5 V. At a cathode potential of -0.7 V, the biocathode in the MECs had a higher current density (MEC 1: 1.9 A/m(2), MEC 2: 3.3 A/m(2)) than a control cathode (0.3 A/m(2), graphite felt without biofilm) in an electrochemical half cell. This indicates that hydrogen production is catalyzed at the biocathode, likely by electrochemically active microorganisms. The cathodic hydrogen recovery was 17% for MEC 1 and 21% for MEC 2. Hydrogen losses were ascribed to diffusion through membrane and tubing, and methane formation. After 1600 h of operation, the current density of the MECs had decreased to 0.6 A/m(2), probably caused by precipitation of calcium phosphate on the biocathode. The slow deteriorating effect of calcium phosphate, and the production of methane show the importance of studying the combination of bioanode and biocathode in one electrochemical cell, and of studying long term performance of such an MEC., (2009 Elsevier B.V. All rights reserved.)

A MFC-based biosensor can act as online toxicity sensor. Electrical current is a direct linear measure for metabolic activity of electrochemically active microorganisms. Microorganisms gain energy from anodic overpotential and current strongly depends on anodic overpotential. Therefore control of anodic overpotential is necessary to detect toxic events and prevent false positive alarms. Anodic overpotential and thus current is influenced by anode potential, pH, substrate and bicarbonate concentrations. In terms of overpotential all factor showed a comparable effect, anode potential 1.2% change in current density per mV, pH 0.43%/mV, bicarbonate 0.75%/mV and acetate 0.8%/mV. At acetate saturation the maximum acetate conversion rate is reached and with that a constant bicarbonate concentration. Control of acetate and bicarbonate concentration can be less strict than control of anode potential and pH. Current density changes due to changing anode potential and pH are in the same order of magnitude as changes due to toxicity. Strict control of pH and anode potential in a small range is required. The importance of anodic overpotential control for detection of toxic compounds is shown. To reach a stable baseline current under nontoxic conditions a MFC-based biosensor should be operated at controlled anode potential, controlled pH and saturated substrate concentrations., (2009 Elsevier B.V. All rights reserved.)

Bioelectrochemical systems (BESs) are emerging technologies which use microorganisms to catalyze the reactions at the anode and/or cathode. BES research is advancing rapidly, and a whole range of applications using different electron donors and acceptors has already been developed. In this mini review, we focus on technological aspects of the expanding application of BESs. We will analyze the anode and cathode half-reactions in terms of their standard and actual potential and report the overpotentials of these half-reactions by comparing the reported potentials with their theoretical potentials. When combining anodes with cathodes in a BES, new bottlenecks and opportunities arise. For application of BESs, it is crucial to lower the internal energy losses and increase productivity at the same time. Membranes are a crucial element to obtain high efficiencies and pure products but increase the internal resistance of BESs. The comparison between production of fuels and chemicals in BESs and in present production processes should gain more attention in future BES research. By making this comparison, it will become clear if the scope of BESs can and should be further developed into the field of biorefineries.

Biological acetate reduction with hydrogen is a potential method to convert wet biomass waste into ethanol. Since the ethanol concentration and reaction rates are low, this research studies the feasibility of using an electrode, in stead of hydrogen, as an electron donor for biological acetate reduction in conjunction of an electron mediator. Initially, the effect of three selected mediators on metabolic flows during acetate reduction with hydrogen was explored; subsequently, the best performing mediator was used in a bioelectrochemical system to stimulate acetate reduction at the cathode with mixed cultures at an applied cathode potential of -550 mV. In the batch test, methyl viologen (MV) was found to accelerate ethanol production 6-fold and increased ethanol concentration 2-fold to 13.5 +/- 0.7 mM compared to the control. Additionally, MV inhibited n-butyrate and methane formation, resulting in high ethanol production efficiency (74.6 +/- 6%). In the bioelectrochemical system, MV addition to an inoculated cathode led directly to ethanol production (1.82 mM). Hydrogen was coproduced at the cathode (0.0035 Nm(3) hydrogen m(-2) d(-1)), so it remained unclear whether acetate was reduced to ethanol by electrons supplied by the mediator or by hydrogen. As MV reacted irreversibly at the cathode, ethanol production stopped after 5 days.

The solar energy powered microbial fuel cell is an emerging technology for electricity generation via electrochemically active microorganisms fueled by solar energy via in situ photosynthesized metabolites from algae, cyanobacteria, or living higher plants. A general problem with microbial fuel cells is the pH membrane gradient which reduces cell voltage and power output. This problem is caused by acid production at the anode, alkaline production at the cathode, and the nonspecific proton exchange through the membrane. Here we report a solution for a new kind of solar energy powered microbial fuel cell via development of a reversible bioelectrode responsible for both biocatalyzed anodic and cathodic electron transfer. Anodic produced protons were used for the cathodic reduction reaction which held the formation of a pH membrane gradient. The microbial fuel cell continuously generated electricity and repeatedly reversed polarity dependent on aeration or solar energy exposure. Identified organisms within biocatalyzing biofilm of the reversible bioelectrode were algae, (cyano)bacteria and protozoa. These results encourage application of solar energy powered microbial fuel cells.

Scaling up microbial fuel cells (MFCs) is inevitable when power outputs have to be obtained that can power electrical devices other than small sensors. This research has used a bipolar plate MFC stack of four cells with a total working volume of 20 L and a total membrane surface area of 2 m(2). The cathode limited MFC performance due to oxygen reduction rate and cell reversal. Furthermore, residence time distribution curves showed that bending membranes resulted in flow paths through which the catholyte could flow from inlet to outlet, while leaving the reactants unconverted. The cathode was improved by decreasing the pH, purging pure oxygen, and increasing the flow rate, which resulted in a 13-fold power density increase to 144 W m(-3) and a volumetric resistivity of only 1.2 mOmega m(3) per cell. Both results are major achievements compared to results currently published for laboratory and scaled-up MFCs. When designing a scaled-up MFC, it is important to ensure optimal contact between electrodes and substrate and to minimize the distances between electrodes.

The hydrogen evolution reaction (HER) at Pt-cathodes of microbial electrolysis cells (MEC) has been associated with overpotentials of several hundred millivolts. The high overpotentials challenge the sustainability of an MEC. This paper shows that the HER overpotential at MEC relevant pH values is reduced if buffer is present At 15 A/m2 and 50 mM buffer, the lowest overpotential for phosphate was -0.05 V at pH 6.2, for ammonia was -0.05 V at pH 9.0, for carbonate was -0.09 V at pH 9.3, for Tris(hydroxymethyl)aminomethane was -0.07 V at pH 7.8, and for N-2-hydroxyethylpiperazine-N'-2-ethanesulfonic acid was -0.08 V at pH 7.2. It was shown that the effect of buffer on the overpotentialis strongly pH dependent Furthermore, experimental data and a mass transport equation showed that by increasing the buffer concentration or linear flow speed (i.e., pump speed), or decreasing the current density (i) the overpotential reduces and (ii) the minimum overpotential is reached at a pH that approaches the buffer dissociation constant (pKa). Thus, to reduce the HER overpotential of an MEC, buffer (i.e., pKa), buffer concentration, linear flow speed, and current density must be well balanced with the expected operational pH.

Acetate reduction is an alternative digestion process to convert organic waste into ethanol. Using acetate for fuel ethanol production offers the opportunity to use organic waste materials instead of sugar-containing feedstock. Methanogenesis, however, competes with acetate reduction for acetate and hydrogen and lowers the final efficiency. The aim of this research is to selectively inhibit methanogenesis and to enhance acetate reduction. Acetate reduction was stimulated in batch tests at pH between 4.5 and 8; and at pH 6 with and without thermal pre-treatment. It was found that methanogenesis was selectively inhibited while acetate reduction was enhanced after thermal pre-treatment incubated at pH 6. Initially the acetate reduction yielded 7.7+/-3.2mM ethanol with an efficiency of 60.2+/-8.7%, but later on it was consumed to form 7.02+/-0.85 mM n-butyrate with an efficiency of 76.2+/-14.0%. It was the first time demonstrated that n-butyrate can be produced by mixed cultures from only acetate and hydrogen.

Electricity production via solar energy capturing by living higher plants and microalgae in combination with microbial fuel cells are attractive because these systems promise to generate useful energy in a renewable, sustainable, and efficient manner. This study describes the proof of principle of a photosynthetic algal microbial fuel cell (PAMFC) based on naturally selected algae and electrochemically active microorganisms in an open system and without addition of instable or toxic mediators. The developed solar-powered PAMFC produced continuously over 100 days renewable biocatalyzed electricity. The sustainable performance of the PAMFC resulted in a maximum current density of 539 mA/m2 projected anode surface area and a maximum power production of 110 mW/m2 surface area photobioreactor. The energy recovery of the PAMFC can be increased by optimization of the photobioreactor, by reducing the competition from non-electrochemically active microorganisms, by increasing the electrode surface and establishment of a further-enriched biofilm. Since the objective is to produce net renewable energy with algae, future research should also focus on the development of low energy input PAMFCs. This is because current algae production systems have energy inputs similar to the energy present in the outcoming valuable products.