Search

This paper presents a novel method for low maintenance, low ambiguity in-situ drift velocity monitoring in large volume Time Projection Chambers (TPCs). The method was developed and deployed for the 40m^3 TPC tracker system of the NA61/SHINE experiment at CERN, which has a one meter of drift length. The method relies on a low-cost multi-wire proportional chamber placed next to the TPC to be monitored, downstream with respect to the particle flux. Reconstructed tracks in the TPC are matched to hits in the monitoring chamber, called the Geometry Reference Chamber (GRC). Relative differences in positions of hits in the GRC are used to estimate the drift velocity, removing the need for an accurate alignment of the TPC to the GRC. An important design requirement on the GRC was minimal added complexity to the existing system, in particular, compatibility with Front-End Electronics cards already used to read out the TPCs. Moreover, the GRC system was designed to operate both in large and small particle fluxes. The system is capable of monitoring the evolution of the drift velocity inside the TPC down to a one permil precision, with a few minutes of data collection., Comment: 18 pages, 9 figures

The ALICE collaboration is proposing a completely new detector, ALICE 3, for operation during the LHC Runs 5 and 6. One of the ALICE~3 subsystems is the Muon IDentifier detector (MID), which has to be optimised to be efficient for the reconstruction of $J/\psi$ at rest (muons down to $p_{\rm T}\approx1.5$ GeV/$c$) for $|\eta|<1.3$. Given the modest particle flux expected in the MID of a few Hz/cm$^2$, technologies like plastic scintillator bars ($\approx1$ m length) equipped with wavelength-shifting fibers and silicon photomultiplier readout, and lightweight Multi-Wire Proportional Chambers (MWPCs) are under investigation. To this end, different plastic scintillator paddles and MWPCs were studied at the CERN T10 test beam facility. This paper reports on the performance of the scintillator prototypes tested at different beam momenta (from 0.5 GeV/$c$ up to 6 GeV/$c$) and positions (horizontal, vertical, and angular scans). The MWPCs were tested at different momenta (from 0.5 GeV/$c$ to 10 GeV/$c$) and beam intensities, their efficiency and position resolutions were verified beyond the particle rates expected with the MID in ALICE 3., Comment: 11 pages, 8 figures, to appear in JINST

Muography is an imaging tool based on the attenuation of cosmic muons to observe the density distribution of large objects, such as underground caves or fractured zones. Tomography based on muography measurements -- that is, three dimensional reconstruction of density distribution from two dimensional muon flux maps -- brings up special challenges. The detector field of view covering must be as balanced as possible, considering the muon flux drop at higher zenith angles and the detector placement possibilities. The inversion from directional muon fluxes to 3D density map is usually underdetermined (more voxels than measurements) which can be unstable due to partial coverage. This can be solved by geologically relevant Bayesian constraints. The Bayesian principle results in parameter bias and artifacts. In this work, the linearized (density-length based) inversion is applied, the methodology is explained, formulating the constraints associated with inversion to ensure the stability of parameter fitting. After testing the procedure on synthetic examples, an actual high quality muography measurement data set from 7 positions is used as input for the inversion. The result demonstrates the tomographic imaging of a complex karstic crack zone and provides details on the complicated internal structures. The existence of low density zones in the imaged space was verified by samples from core drills, which consist altered dolomite powder within the intact high density dolomite., Comment: submitted to Geophys. J. Int

Gaseous detectors are widely used in high energy physics, and are attractive choices in tracking systems for cosmic muon imaging, also called muography. Such detectors offer high resolution and high efficiency at reasonable cost for large sizes, however, one of the drawbacks is that the gaseous detection medium must be prevented from contamination by outside air or internal outgassing. Standard systems work with a constant gas flow, leading to regular maintenance in the form of gas cylinder changes, which can be an issue for remote field applications. In this paper we discuss the practical possibilities to reduce gas consumption of an outdoor gaseous tracker, where particularly the gas density change from daily temperature cycling limits the input flow. Such "breathing" effect can be circumvented by well designed buffer volume, which must prevent external air contamination. A realistic MWPC tracking test system with 0.9 square meter area, total volume of 160 l, has been operated for 36 days with a flow of 3 l/day, confirming that the buffer volume, in this case a 50 m long and 10 l volume low diffusion tube, ensures sufficient gas quality. The key effects governing the gas flow dynamics, including diffusion and gas volume change, has been studied quantitatively, leading to practical design prescriptions., Comment: 20 pages, 12 figures. The following article has been submitted to Journal of Applied Physics under Manuscript #JAP21-AR-01969

In recent years Gas Electron Multipliers have proven to be reliable amplification stages at high beam rates, and can be used also in Time Projection Chambers. Our group developed a 1 dm$^3$ active volume double-GEM TPC, with spatial resolution of 50 $\mu m$ and 280 $\mu$m. Custom designed FPGA data acquisition system enables rate capability for about 100 kHz$\cdot$mm$^{-2}$, providing excellent track-by-track position and angular information, better than 0.1 mm and 1 mrad respectively. The wide dynamic range of the system enables identification from $^{4}$He up to $^{86}$Kr using ionization measurement. Two of these TPCs are planned to operate in tandem mode to filter off-time particles and to achieve a superior angular resolution.

A tracking detector system has been constructed with an innovative approach to the classical multi-wire proportional chamber concept, using contemporary technologies. The detectors, covering an area of 0.58 square meters each, are optimized for the application of muon radiography. The main features are high (>99.5%) and uniform detection efficiency, 9 mm FWHM position resolution, filling gas consumption below 2 liters per hour for the non toxic, non flammable argon and carbon dioxide mixture. These parameters, along with the simplicity of the construction and the tolerance for mechanical effects, make the detectors to be a viable option for a large area muography observation system., Comment: 15 pages, 15 figures

In this paper, measurement results and experimental methodology are presented on the determination of multiplication distributions of avalanches initiated by single electron in GEM foils. The measurement relies on the amplification of photoelectrons by the GEM under study, which is subsequently amplified in an MWPC for signal enhancement and readout. The intrinsic detector resolution, namely the sigma-over-mean ratio of the multiplication. distribution is also elaborated. Small gain dependence of the shape of the avalanche response distribution is observed in the range of net effective gain of 15 to 100. The distribution has an exponentially decaying tail at large amplitudes. At small amplitudes, the applied working gas is seen to have a well visible effect on the shape of the multiplication distribution. Equivalently, the working gas has an influence on the intrinsic detector resolution of GEMs via suppression of the low amplitude responses. A sigma-over-mean ratio of 0.75 was reached using a neon based mixture, whereas other gases provided an intrinsic detector resolution closer to 1, meaning a multiplication distribution closer to the low-field limit exponential case., Comment: 27 pages, 18 figures

A set of classical multi-wire proportional chambers were designed and constructed with the main purpose of efficient cosmic muon detection. These detectors are relatively simple to construct, and at the same time are low cost, making them ideal for educational purposes. The detector layers have efficiencies above 99% for minimum ionizing cosmic muons, and their position resolution is about 1 cm, that is, particle trajectories are clearly observable. Visualization of straight tracks is possible using an LED array, with the discriminated and latched signal driving the display. Due to the exceptional operating stability of the chambers, the design can also be used for cosmic muon telescopes., Comment: 11 pages, 11 figures. Submitted to the European Journal of Physics