Search

The structural responses of cold-formed high strength steel (HSS) square and rectangular hollow section (SHS and RHS) beams at elevated temperatures were examined in this study. Stress-strain relationships of cold-formed HSS at elevated temperatures were proposed and verified against material test results. The proposed stress-strain relationships were then employed in a finite element (FE) analysis to study the behaviour of cold-formed HSS SHS/RHS beams at elevated temperatures up to 1000 °C. The developed FE model was verified with available test results of cold-formed HSS SHS/RHS beams; upon verification, a total of 252 numerical flexural capacities were gained from FE analyses. The numerical results were used to investigate the suitability of existing cross-section slenderness limits to the HSS tubular sections at elevated temperatures. The applicability of current flexural design provisions in the Eurocode 3, AISC and AISI specifications to the investigated HSS tubular beams at elevated temperatures was also examined. Overall, it is shown that the codified provisions can provide quite conservative predictions; an improved design rule is proposed by modifying the direct strength method (DSM) in the AISI specification. Furthermore, reliability analyses were carried out to assess reliability levels of codified and modified provisions. It has been demonstrated that the modified DSM can produce accurate and reliable design and therefore is recommended to be used for cold-formed HSS SHS/RHS beams at elevated temperatures.

The structural response of cold-formed high strength steel (CFHSS) rectangular hollow sections (RHS) under localised bearing forces is investigated. Web crippling tests were undertaken on cold-formed steel RHS that had nominal yield strengths (0.2% proof stresses) of 700 and 900 MPa. The experiments were conducted under end and interior load cases. The experimental results were utilised in a numerical investigation to verify finite element (FE) models. Upon verification, an extensive parametric study was conducted. The ultimate capacities obtained experimentally and numerically were compared with nominal resistances computed by the current North American Specification, European Code and Australian Standard. Overall, the codified resistance provisions gave either unconservative or overly conservative predictions. Therefore, improved design rules for CFHSS RHS under localised bearing forces were proposed. The reliability of the codified as well as modified design provisions were appraised. It is demonstrated that the modified design rules proposed in this paper can provide reliable predictions for the CFHSS RHS under localised bearing forces.

The flexural buckling behaviour and residual strengths of stainless steel circular hollow section (CHS) columns after exposure to fire were studied, based on a thorough experimental and numerical modelling programme, and reported in this paper. The experimental programme was performed on three series of specimens, and each series contained five geometrically identical specimens, with one unheated and the other four heated to different levels of elevated temperatures (namely 300 °C, 600 °C, 800 °C and 1000 °C). The detailed heating, soaking and cooling processes, material testing and pin-ended column tests were described, with the derived key experimental results fully presented. The testing programme was supplemented by a numerical modelling programme, including a validation study where finite element models were developed and validated against the test results, and a parametric study where the validated finite element models were employed to derive further numerical results over an extended range of cross-section dimensions and member lengths. Due to the absence of existing design codes for stainless steel structures after exposure to fire, the codified design provisions for stainless steel CHS columns at ambient temperature, as established in the Europe, America and Australia/New Zealand, were assessed for their applicability to stainless steel CHS columns after exposure to fire, based on the obtained test and numerical data. The assessment results generally revealed that the design buckling curve, as adopted in the European code, and the tangent modulus method, as employed in the American specification, lead to unsafe and scattered design flexural buckling strengths for stainless steel CHS columns after exposure to fire, while the explicit approach, as used in the Australian/New Zealand standard, yields a high level of accuracy and consistency in predicting the post-fire flexural buckling strengths of stainless steel CHS columns.

The behaviour and resistances of cold-formed stainless steel rectangular hollow section (RHS) members undergoing combined bending and web crippling were studied based upon experimental and numerical investigations. A test program consists of 4 pure bending tests, 7 pure web crippling tests and 23 web crippling-bending interaction tests was conducted. The RHS specimens were cold-rolled from lean-duplex and ferritic stainless steel sheets. Numerical models were built and validated against the test results. Upon validation, parametric studies comprised of 312 finite element analyses were undertaken. The obtained test and numerical results were compared with nominal resistances predicted from the American, Australian/New Zealand and European design standards for stainless steel structures. Moreover, the provisions in the North American Specification for cold-formed steel members were also evaluated. The comparison results indicate that the codified design provisions are generally safe to use for design of cold-formed stainless steel RHS members undergoing combined bending and web crippling, among which the European provision yields overly-conservative predictions. The codified web crippling-bending interaction curves can be applied for designing the stainless steel RHS members undergoing combined bending and web crippling, whilst improved predictions could be achieved by employing recently proposed bending and web crippling design rules.

Design of cold-formed stainless steel tubular columns undergoing local-overall flexural interactive buckling is investigated in this paper. A numerical study has been carried out to study the interactive buckling behavior of square hollow section (SHS) and rectangular hollow section (RHS) columns of various stainless steel grades that are employed in structural applications. A finite element model was developed and verified against available experimental cold-formed stainless steel SHS/RHS column data. Extensive parametric studies, with cross-section aspect ratio, plate slenderness, overall slenderness and stainless steel grade selected as key variable parameters, were carried out thereafter to generate further numerical data featuring the tubular columns undergoing local-flexural interactive buckling. The obtained interactive buckling strengths were used to assess the design provisions in current European, American, Australian/New Zealand and Chinese design standards for stainless steel structures as well as available Direct Strength Method (DSM) design rules in the literature. It is shown that better predictions can be achieved when material nonlinearities of different material grades are accounted for. A modified DSM, which relies on simple hand calculations, is developed in this paper. It is demonstrated that the modified DSM is a suitable and efficient design alternative for cold-formed stainless steel SHS/RHS columns subjected to local-flexural interactive buckling.

This paper presents experimental and numerical investigations on cold-formed ferritic stainless steel (CFFSS) square and rectangular hollow sections undergoing web crippling. A total of 44 web crippling tests was carried out under the four codified web crippling load cases as per the American cold-formed stainless steel specification. Numerical model of each load case was built and verified with the web crippling test results. After the verification, a parametric study comprised of 154 finite element analyses was undertaken thereafter to gain further insight into the behaviour of the CFFSS sections undergoing web crippling. The current design provisions in the American, Australian/New Zealand and European stainless steel codes of practice were assessed. Moreover, the North American Specification (NAS) provisions for carbon and low-alloy steel sections were evaluated. Furthermore, design recommendations in the literature for stainless steel sections were examined. Improved design rules are proposed in this study for CFFSS square and rectangular hollow sections by modifying NAS and Direct Strength Method. Reliability analysis was also undertaken to assess the reliability levels of the existing and modified provisions.

The research work described in this paper was supported by a grant from the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. 17209614).

This paper presents an experimental investigation on residual mechanical properties of high strength steels (HSS) after exposure to fire. A test program was conducted to study the post-fire mechanical properties of cold-formed HSS. A total of 41 tensile coupon specimens was extracted from cold-formed tubular sections with nominal yield stresses of 700 and 900 MPa. The specimens were exposed to various elevated temperatures ranged from 200 to 1000 °C and then cooled down to ambient temperature before testing. Stress-strain curves were obtained and the mechanical properties of Young's modulus, yield stress (0.2% proof stress), ultimate strength, ultimate strain and fracture strain of the cold-formed high strength steel materials after exposure to elevated temperatures were derived. The post-fire retention factors that obtained from the tests were compared with existing predictive equations in the literature. The influence of heating rate on post-fire mechanical properties was also investigated. New predictive curves for the determination of residual mechanical properties of HSS after exposure to fire are proposed. It is demonstrated that the proposed predictive curves are suitable for both cold-formed and hot-rolled HSS with nominal yield stresses ranged from 690 to 960 MPa.

The behaviour and resistances of concrete-filled ferritic stainless steel tubular (CFFSST) joints were studied and presented in this paper based upon experimental and numerical investigations. A test program was firstly undertaken on a series of X- and T-joints with square and rectangular hollow section (SHS and RHS) chords. The stainless steel SHS/RHS tubes were cold-rolled from EN 1.4003 ferritic grade sheets, and the specimens were in-filled with either normal or high strength concrete. The experimental study including the detailed material properties, joint test setups, test procedures and results is reported. Numerical models were also developed and verified against the CFFSST joint test results, and followed by a parametric study generating further numerical results over a wider range of key joint parameters. The obtained experimental and numerical CFFSST joint capacities were compared with existing design recommendations as per the CIDECT Design Guide and design rules proposed by previous researchers. The comparison results indicate that the existing provisions are not capable of predicting the capacities of the investigated composite tubular joints in an accurate and reliable manner. Hence, modified design rules are put forward in this paper for the design of CFFSST joints.

The behaviour and design of cold-formed ferritic stainless steel tubular structural members subjected to concentrated bearing loads are presented in this paper. A total of 37 web crippling tests was conducted on cold-formed square and rectangular hollow sections of grade EN 1.4003 ferritic stainless steel. The tests were conducted under end loading and interior loading conditions, which closely simulated the support conditions of floor joist members seated on solid foundation. Finite element (FE) models were developed and validated against the experimental results. Upon validation of the FE models, a parametric study comprised 160 FE analyses was performed using the validated models. The web crippling strengths obtained from experimental and numerical investigations were compared with the nominal strengths calculated using the current American, Australian/New Zealand and European specifications for stainless steel structures. Furthermore, the North American Specification (NAS) and the Australian Standard AS4100 for carbon steel structures as well as the suggested design rules in the literature for stainless steel structures were also compared. Improved design rules are proposed for ferritic stainless steel tubular structural members subjected to concentrated bearing loads by means of modified NAS and Direct Strength Method. The reliability of the proposed design rules has been assessed through reliability analysis.

This paper presents an experimental investigation of cold-formed high strength steel tubular sections undergoing web crippling. The tests were conducted on square and rectangular hollow sections of high strength steel with nominal 0.2% proof stresses of 700 and 900 MPa. The measured web slenderness values of the tubular sections ranged from 8.3 to 35.8. Tensile and compression coupon tests were conducted to obtain the material properties of the test specimens. The web crippling tests were conducted under the four loading conditions as specified in the North American Specification and Australian/New Zealand Standard for cold-formed steel structures, namely, the End-One-Flange, Interior-One-Flange, End-Two-Flange and Interior-Two-Flange loading conditions. It should be noted that the web crippling design provisions in these two specifications were mainly developed based on sections with web slenderness value greater than 40 and 0.2% proof stress less than 500 MPa. The test strengths obtained from this study were compared with the nominal strengths calculated from the North American Specification, Australian/New Zealand Standard and European Code for cold-formed steel structures. Furthermore, the test strengths were also compared with the nominal strengths calculated from the Australian Standard AS4100. Reliability analysis was performed to assess the reliability of the design provisions in the aforementioned specifications. Generally, it is shown that the nominal strengths predicted by the codified web crippling design provisions are either unconservative or very conservative. Hence, the existing codified design provisions are not appropriate for the cold-formed high strength steel square and rectangular hollow sections undergoing web crippling.

This paper presents the material properties of cold-formed high strength steel at elevated temperatures. Material properties at elevated temperatures have a crucial role in fire resistance design of steel structures. The fire resistances of steel structures in the existing international standards are mainly based on experimental data of hot-rolled mild steel. However, investigation of high strength steel at elevated temperatures is limited. Therefore, a test program has been carried out to investigate the material properties of cold-formed high strength steel at elevated temperatures. The coupon specimens were extracted from cold-formed high strength steel square and rectangular hollow sections with nominal yield stresses of 700 and 900 MPa at ambient temperature. The coupon tests were carried out through both steady and transient state test methods for temperatures up to 1000 °C. Material properties including thermal elongation, elastic modulus, yield stress, ultimate strength, ultimate strain and fracture strain were obtained from the tests. The test results were compared with the design values in the European, American, Australian and British standards. The comparison results revealed the necessity of proposing specified design rules for material properties of cold-formed high strength steel at elevated temperatures. New design curves to determine the deterioration of material properties of cold-formed high strength steel at elevated temperatures are proposed. It is shown that the proposed design curves are suitable for high strength steel materials with nominal yield stresses ranged from 690 to 960 MPa at ambient temperature.

This paper presents experimental and numerical investigations of cold-formed high-strength steel (CFHSS) tubular structural members under combined bending and bearing. A test program that c...

Orthotropic Steel Decks (OSDs) are widely used in various steel bridge types and however, their fatigue performances remain a prominent issue. In this paper, experimental work was conducted to investigate the hot spot stresses at various details of rib-to-deck-to-floor beam (RDF) welded connection in OSDs reinforced by ultra-high-performance concrete (UHPC). Quadratic extrapolation approach was applied to determine the hot spot stresses at weld toes of different fatigue prone details according to IIW specifications. Parametric studies were performed using finite element analysis to examine the effect of structural key parameters on the hot spot stresses including UHPC layer thickness and UHPC elastic modulus. Experimental results indicated that longitudinal flexural increased the out-of-plane distortions of the U-rib walls, therefore the hot spot stresses at locations on the U-rib were remarkably higher than that around floor beam cut-out. It is observed that hot spot stresses at region A on the U-rib wall directly under the acting load were controlled by tensile stresses, while region B on the other side of the acting load had compression stresses. The application of 60 mm UHPC layer significantly reduced the hot spot stresses at critical location on the U-rib and around floor beam cut-out by 57.8% and 36.5%, respectively. Parametric study results demonstrated that increasing UHPC layer thickness significantly reduced the hot spot stresses at all considered locations, while increasing the elastic modulus of UHPC layer slightly influenced the hot spot stresses and its effect can be neglected.

The recently discovered Halatumiao magmatic Ni-Cu sulfide deposit is located in the western part of the Baolidao terrane, which represents the middle-eastern segment of the Central Asian Orogenic Belt (CAOB), Inner Mongolia, NE China. This deposit is an important case of a magmatic sulfide deposit related to Early Permian subduction magmatism in an arc setting. In this contribution, we report in-situ zircon U-Pb ages, whole-rock major and trace element and PGE data, and Os and S isotope compositions from the Halatumiao ore-bearing intrusion to constrain its genesis and relationship to the Early Permian subduction-related magmatism. The Halatumiao mafic-ultramafic intrusion is composed of wehrlite, olivine websterite and gabbro. Semi-massive and disseminated sulfide mineralization with a pentlandite + pyrrhotite + chalcopyrite assemblage occurs in both mafic and ultramafic rocks of the intrusion. In-situ dating of magmatic zircon grains separated from an ultramafic rock sample yielded a U-Pb age of 292.3 ± 1.5 Ma. This age is very close to the age of the Erbutu Ni-Cu sulfide deposit (294.2 ± 2.7 Ma) located in the western part of the northern margin of the North China craton. The high Ni/Cu ratios (6.7 in average, except one sample) of ore samples indicate that the parental magma to the Halatumiao deposit was a primitive basalt. The good positive correlation between IPGEs (Ir vs. Os, Ru and Rh) indicates that fractional crystallization of MSS is the key factor for the PGE tenors. The positive γOs(t) values (from +46 to +68) and mantle-like S isotopic compositions (δ34S mostly between −1.5 and 0.5‰), The trace element characteristics show that a minor to moderate degree of crustal contamination (5–10%) has occurred in the magma. Fractional crystallization and crustal contamination were likely the key factors for sulfide saturation in the Halatumiao mafic magma. The relatively high Ni tenors of sulfides (avg. 6.4 wt%) indicate that the Late Paleozoic mafic-ultramafic intrusions abounding in the Xing’an-Inner Mongolia region have a good potential for hosting economic Ni-Cu sulfide mineralization.

In order to prepare electroformed nickel with excellent properties, the effect of different waveforms on microstructure and mechanical properties was investigated by optical microscopy (OM), X-ray diffraction (XRD) and tensile test, respectively. The results show that the samples are composed of micron columnar grains with high-density nanoscale coherent twin boundaries which are parallel to the growth plane. The tensile strength and elongation display opposite tendency with the increase in current density when direct current (DC) electroforming was applied. However, under the condition of pulse current (unidirectional, bidirectional) electroforming, the change regulation of tensile strength and elongation is close while cathode (peak, positive peak) current density increases. XRD results show that electroformed nickel layers with high purity are all fcc crystal configuration under different conditions of the current waveform. The nickel layers formed under bidirectional pulse current behave superior global performance with tensile strength of 692.0 MPa and elongation of 27.6 %.

Orthotropic steel decks (OSDs) are widely used in long span steel bridges owing to their outstanding structural characteristics and lightweight; however, the fatigue resistance of OSDs is still a prominent problem of such deck structures. Ultra-High-Performance Concrete (UHPC) has been recently employed in orthotropic steel decks to enhance their structural behavior and extend their fatigue life. In this paper, experimental work has been carried out to investigate the effect of employing UHPC overlay on the hot spot stresses at fatigue prone details of OSDs. Three full scale rib-to-deck-to-floor beam (RDF) welded connections were fabricated and tested. One centric wheel load was applied; so that, the effect of in-plane and out-of-plane distortions of floor beam web can be considered. In parallel with the experimental program, a finite element (FE) analysis was also performed. Upon validation of FE models against experimental results, a parametric study was carried out to study the effect of key structural parameters that primarily influence the hot spot stresses. Experimental results indicated that, the stresses around floor beam cut-out were slightly higher than the hot spot stresses at considered locations on U-rib due to in-plane and out-of-plane distortions of the floor beam web under centric loading. The application of 60 mm UHPC layer effectively reduced the hot spot stresses by 26–83% at the considered locations of the test specimens. Results of parametric study indicated that, increasing UHPC layer thickness significantly enhanced the stiffness of the bridge deck and therefore effectively reduced the hot spot stresses at considered spots. On the other hand, the effect of increasing UHPC elastic modulus slightly influenced the hot spot stresses at considered locations and its effect is deemed neglectable.

This paper presents an experimental investigation of concrete-filled high-strength steel tubular X joints. The high-strength steel tubes were cold formed into square and rectangular hollow ...

The rapid development of the Internet has made online shopping become a common thing. Now, about 1/4 of the e-commerce users are post-95s, the permeability of online shopping has increased year by year. People in their 19-24 year old is the main group of online shopping. The college students are exactly in this age order. Their personality is distinctive, they are young and willing to accept new things, and skilled in using the Internet. Online shopping is one of their main way of shopping. The analysis method of the research, by using the SPSS24.0 data analysis software, draws a conclusion that the commodity factors and network retailer factors and guiding factors have significant positive influence on the intention of online shopping for female college students, and the online shopping intention has significant positive influence on the behavior of online shopping for female college students. According to the research findings, suggestions for cosmetics online retailers are put forward.

[EN] The structural performance and design of concrete-filled high strength steel tubular X-joints subjected to compression are investigated. A numerical investigation on the behaviour of concrete-filled high strength steel tubular chord members under concentrated bearing load has been performed. The high strength steel tubes had nominal yield stresses of 700 and 900 MPa. The infilled concrete had nominal concrete cylinder strengths of 35 and 100 MPa. In order to avoid the failure of brace members and reveal the true capacity of the X-joints, steel bearing plates were used to simulate the brace members. A finite element model was developed and validated against test results. Furthermore, a parametric study comprised 156 finite element analyses was carried out. The strengths of the concrete-filled high strength steel square and rectangular hollow section X-joints obtained from the parametric study together with available data in the literature were compared with the nominal strengths calculated from the CIDECT Design Guide. It is shown that the CIDECT design predictions exhibit significant scatter and could be unconservative for the concrete-filled tubular joints with chord sidewall slenderness ratio beyond 40 in this study. Hence, new design rules are proposed for concrete-filled high strength steel tubular X-joints subjected to compression. It is shown that the proposed design rules are able to provide reasonably good predictions., The research work described in this paper was supported by a grant from the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. 17209614).

With an in-depth analysis of nursing work in 14 hospitals over a period of two years, one unique total nursing information system framework was established where the nursing clinical pathways are used as the main frame and the nursing orders as the nodes on the frame. We used the nursing order concept with the principles of nursing process. A closed-loop management model composed of the nursing orders was set up to solve nursing problems. Based on the principles of traditional Chinese medicine, we further designed an intelligent support module to automatically deduct clinical nursing pathways to promote standardized management and improve the quality of nursing care. The system has successfully been implemented in some facilities since 2015.

High strength steels are becoming increasingly attractive for structural and architectural applications due to their superior strength-to-weight ratio which could lead to lighter and elegant structures. The stiffness and strength of high strength steels may reduce after exposure to fire. The post-fire mechanical properties of high strength steels have a crucial role in evaluating the residual strengths of these materials. This paper presents an experimental investigation on post-fire mechanical properties of cold-formed high strength steels. A series of tensile coupon tests has been carried out. The coupon specimens were extracted from cold-formed square hollow sections with nominal yield stresses of 700 and 900 MPa at ambient temperature. The specimens were exposed to various elevated temperatures ranged from 200 to 1000 °C and then cooled down to ambient temperature before tested to failure. Stress-strain curves were obtained and the mechanical properties, namely, Young’s modulus, yield stress (0.2% proof stress) and ultimate strength, of the cold-formed high strength steel materials after exposure to elevated temperatures were derived. The post-fire retention factors that obtained from the experimental investigation were compared with existing predictive equations in the literature. New predictive equations are proposed to determine the residual mechanical properties of high strength steels after exposure to fire. It is shown that the proposed predictive equations are suitable for both cold-formed and hot-rolled high strength steel materials with nominal yield stresses ranged from 690 to 960 MPa.

In this study, the dense and well-integrated Ir films were electrodeposited on Pt substrate at a constant current process in the NaCl-KCl molten salt system containing IrCl3. The morphology and constitution of the Ir films at different process conditions were examined by scanning electron microscope (SEM), energy dispersive spectroscope (EDS) and X-ray diffraction (XRD) respectively. The results showed that IrCl3 concentration had significantly influenced the surface morphology of the Ir film. The particles of the deposition film surface became lager with increasing the fraction of IrCl3 and gradually decreased with increasing the temperature. However, the film quality decreased due to the formation of some tiny holes when further increasing the temperature. The particle size decreased gradually with the increase of deposition current density. The addition of CsCl could not only reduce the molten salt temperature but also increase the deposition rate of Ir.

The surface of pure titanium was coarsened by anodizing. Hydroxyapatite (HA) coatings were electrodeposited on the anodized pure titanium in a simulated body fluid. Complementary characterization methods (SEM, XRD, static contact angle, roughness tester, universal testing) were used to investigate the features of the coatings. The results of this study indicate that porous surfaces can be achieved on the pure titanium by anodizing, and the HA coatings show a relatively regular network structure. Moreover, HA coatings exhibit a certain roughness, good wettability and rather high shear strength.

This paper introduces a novel and highly efficient realization of a spherical vector quantizer (SVQ), the “Gosset Low Complexity Vector Quantizer” (GLCVQ). The GLCVQ codebook is composed of vectors that are located on spherical shells of the Gosset lattice E8. A high encoding efficiency is achieved by representing the spherical vector codebook as aggregated permutation codes. Compared to previous algorithms, the computational complexity and memory consumption is further reduced by exploiting the properties of so called classleader root vectors and by a novel approach for the codevector-to- index-mapping. The GLCVQ concept can be generalized to vector dimensions that are multiples of eight. In particular, GLCVQ for 16-dimensional vectors is used in Amd. 6 to ITU-T Rec. G.729.1.

This paper describes the speech and audio codec that has been submitted to ITU-T by Huawei and ETRI as a candidate for the upcoming super-wideband and stereo extensions of Rec. G.729.1 and G.718. The core codec in the current implementation is G.729.1 and the encoded frequency range is increased from 7 kHz to 14 kHz. Therefore, the maximum bit rate is raised from 32 kbit/s to 64 kbit/s by adding five bitstream layers. A comprehensive overview of the codec is presented with a focus on the mono coding components. The results of the listening tests that have been conducted during the ITU-T qualification phase are summarized. The proposed codec passes all quality requirements for mono input signals.

Pulse stress tests on magnetic tunnel junctions (MTJs) with a MgO barrier (~5.5 Aring) were conducted. Both the E (McPherson and Mogul, 1998) and 1/E (Chen and Holland, 1985; Schuegraf and Hu, 1994) models can describe the intrinsic breakdown behavior of this ultrathin barrier within the range of voltages studied. While constant voltage stress (CVS) and ramped voltage pulse stress (RVPS) testing yield different experimental failure times for the same failure voltage, accounting for the buildup of degradation from each pulse in the RVPS testing yields the same fundamental degradation rate for the two techniques. The barrier parameter change (before hard breakdown) is related to trap generation and trapped electrons. The variation in the barrier parameters after constant stress testing was also studied by fitting I-V data using Simmons' model (1963). A decrease in the effective barrier thickness and an increase in the effective barrier height were found after constant current/voltage stress. Annealing MTJs with minor damage for 2 hours at 120degC restored the stressed barrier to its initial state.

Current design provisions for web crippling resistance for stainless steel cold-formed sections in EN1993-1-4 follow the ones proposed in EN 1993-1-3 for carbon steel. Several researches in last years demonstrate that this proposals could be unsafe due to the particular non-linear behavior of stainless steel. The objective is to evaluate the proposals publish in the last years, compare the collected experimental and numerical results when applying different proposals and define a new expression for stainless steel.