Search

The redox reaction between natural Fe-containing clay minerals and its sorbates is a fundamental process controlling the cycles of many elements such as carbon, nutrients, redox-sensitive metals, and metalloids (e.g., Co, Mn, As, Se), and inorganic as well as organic pollutants in Earth's critical zone. While the structure of natural clay minerals under oxic conditions is well-known, less is known about their behavior under anoxic and reducing conditions, thereby impeding a full understanding of the mechanisms of clay-driven reduction and oxidation (redox) reactions especially under reducing conditions. Here we investigate the structure of a ferruginous natural clay smectite, nontronite, under different redox conditions, and compare several methods for the determination of iron redox states. Iron in nontronite was gradually reduced chemically with the citrate-bicarbonate-dithionite (CBD) method. 57 Fe Mössbauer spectrometry, X-ray photoelectron spectroscopy (XPS), X-ray absorption near edge structure (XANES) spectroscopy including its pre-edge, extended X-ray absorption fine structure (EXAFS) spectroscopy, and mediated electrochemical oxidation and reduction (MEO/MER) provided consistent Fe(II)/Fe(III) ratios. By combining X-ray diffraction (XRD) and transmission electron microscopy (TEM), we show that the long-range structure of nontronite at the highest obtained reduction degree of 44% Fe(II) is not different from that of fully oxidized nontronite except for a slight basal plane dissolution on the external surfaces. The short-range order probed by EXAFS spectroscopy suggests, however, an increasing structural disorder and Fe clustering with increasing reduction of structural Fe., Competing Interests: The authors declare no competing financial interest., (© 2023 The Authors. Published by American Chemical Society.)

Contaminant removal from (waste)waters by magnetite is a promising technology. In the present experimental study, a magnetite recycled from the steel industry waste (zero-valent iron powder) was used to investigate the sorption of As, Sb and U in phosphate-free and -rich suspensions, i.e. as a remediation for the acidic phosphogypsum leachates derived from the phosphate fertilizer industry. The results showed up to 98% U removal under controlled pH conditions, while phosphate did not hinder this immobilisation. In contrast, the results confirmed the limited uptake of As and Sb oxyanions by magnetite in presence of phosphate as the competing anion, displaying only 7-11% removal, compared to 83-87% in the phosphate-free sorption experiments. To limit this wastewater problem, raw ZVI anaerobic oxidation was examined as mechanism to increase the pH and as a source of Fe 2+ in a first step, and in a second step to remove phosphate via vivianite precipitation, therefore prior to the reaction with magnetite. UV-Vis, XRD and SEM-EDS showed that vivianite precipitation is feasible at pH > 4.5, mainly depending on the phosphate concentration. The higher the [PO 4 3- ], the lower is the pH at which vivianite precipitates and the higher the % removal of phosphate from solution. It is anticipated that an optimum 3-steps design with separate reactors controlling the conditions of ZVI oxidation, followed by vivianite precipitation and finally, reaction with magnetite, can achieve high contaminant uptake in field applications., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Different iron oxides (i.e., magnetite, maghemite, goethite, wüstite), particularly nanosized particles, show distinct effects on living organisms. Thus, it is of primary importance for their biomedical applications that the morphology and phase-structural state of these materials are investigated. The aim of this work was to obtain magnetic nanoparticles in a single reactor using Fe(III) acetylacetonate as the initial precursor for the synthesis of Fe(III) oleate or Fe(III) undecylate followed by their thermolysis in situ. We proposed a new approach, according to which the essential magnetite precursor (a complex salt of higher acids - Fe(III) alkanoates) is obtained in a solvent with a high boiling point via displacement reaction of acetylacetone with a higher acid from Fe(III) acetylacetonate during its elimination from the reaction mixture under vacuum conditions. Magnetic nanoparticles (NPM) were characterized in terms of morphology, hydrodynamic diameter, and composition via several techniques, such as transmission electron microscopy, dynamic light scattering, thermogravimetric analysis, Fourier-transform infrared spectroscopy/attenuated total reflectance, 57 Fe Mössbauer spectroscopy, and X-ray diffraction. The effect of unsaturated oleic (OA) and undecylenic (UA) acids, which are both used as a reagent and as a nanoparticle stabilizer, as well as the influence of their ratio to Fe(III) acetylacetonate on the properties of particles were investigated. Stable dispersions of NPM were obtained in 1-octadecene within the OA or UA ratio from 3.3 mol to 1 mol of acetylacetonate and up to 5.5 mol/mol. Below the mentioned limit, NPM dispersions were colloidally unstable, and at higher ratios no NPM were formed which could be precipitated by an applied magnetic field. Monodisperse nanoparticles of iron oxides were synthesized with a diameter of 8-13 nm and 11-16 nm using OA and UA, respectively. The organic shell that enables the particle to be dispersed in organic media, in the case of oleic acid, covers their inorganic core only with a layer similar to the monomolecular layer, whereas the undecylenic acid forms a thicker layer, which is 65% of the particle mass. The result is a significantly different resistance to oxidation of the nanoparticle inorganic cores. The core of the particles synthesized using oleic acid is composed of more than 90% of maghemite. When undecylenic acid is used for the synthesis, the core is composed of 75% of magnetite., (Copyright © 2023, Nahorniak et al.)

The mobility of 79 Se, a fission product of 235 U and long-lived radioisotope, is an important parameter in the safety assessment of radioactive nuclear waste disposal systems. Nonradioactive selenium is also an important contaminant of drainage waters from black shale mountains and coal mines. Highly mobile and soluble in its high oxidation states, selenate (Se( VI )O 4 2- ) and selenite (Se( IV )O 3 2- ) oxyanions can interact with magnetite, a mineral present in anoxic natural environments and in steel corrosion products, thereby being reduced and consequently immobilized by forming low-solubility solids. Here, we investigated the sorption and reduction capacity of synthetic nanomagnetite toward Se(VI) at neutral and acidic pH, under reducing, oxygen-free conditions. The additional presence of Fe( II ) aq , released during magnetite dissolution at pH 5, has an effect on the reduction kinetics. X-ray absorption spectroscopy analyses revealed that, at pH 5, trigonal gray Se(0) formed and that sorbed Se(IV) complexes remained on the nanoparticle surface during longer reaction times. The Se(0) nanowires grew during the reaction, which points to a complex transport mechanism of reduced species or to active reduction sites at the tip of the Se(0) nanowires. The concomitant uptake of aqueous Fe(II) and Se(VI) ions is interpreted as a consequence of small pH oscillations that result from the Se(VI) reduction, leading to a re-adsorption of aqueous Fe(II) onto the magnetite, renewing its reducing capacity. This effect is not observed at pH 7, where we observed only the formation of Se(0) with slow kinetics due to the formation of an oxidized maghemite layer. This indicates that the presence of aqueous Fe(II) may be an important factor to be considered when examining the environmental reactivity of magnetite.

Fe-substituted YFe x Cr 1-x O 3 crystalline compounds show promising magnetic and multiferroic properties. Here we report the synthesis and characterization of several compositions from this series. Using the autocombustion route, various compositions (x = 0.25, 0.50, 0.6, 0.75, 0.9, and 1) were synthesized as high-quality crystalline powders. In order to obtain microscopic and atomic information about their structure and magnetism, characterization was performed using room temperature X-ray diffraction and energy dispersion analysis as well as temperature-dependent neutron diffraction, magnetometry, and 57 Fe Mössbauer spectrometry. Rietveld analysis of the diffraction data revealed a crystallite size of 84 (8) nm for YFeO 3 , while energy dispersion analysis indicated compositions close to the nominal compositions. The magnetic results suggested an enhancement of the weak ferromagnetism for the YFeO 3 phase due to two contributions. First, a high magnetocrystalline anisotropy was associated with the crystalline character that favored a unique high canting angle of the antiferromagnetic phase (13°), as indicated by the neutron diffraction analysis. This was also evidenced by the high magnetic hysteresis curves up to 90 kOe by a remarkable high critical coercivity value of 46.7 kOe at room temperature. Second, the Dzyaloshinskii-Moriya interactions between homogenous and heterogeneous magnetic pairs resulted from the inhomogeneous distribution of Fe 3+ and Cr 3+ ions, as indicated by 57 Fe Mössbauer studies. Together, these results point to new methods of controlling the magnetic properties of these materials.

We present the study of pristine and calcined f-MWCNTs functionalized by nitrogen-containing functional groups. We focus on the structural and microstructural modification tuned by the previous annealing. However, our primary goal was to analyze the electronic structure and magnetic properties in relation to the structural properties using a multi-technique approach. The studies carried out by X-ray diffraction, XPS, and 57 Fe Mössbauer spectrometry revealed the presence of γ-Fe nanoparticles, Fe 3 C, and α-FeOOH as catalyst residues. XPS analysis based on the deconvolution of core level lines confirmed the presence of various nitrogen-based functional groups due to the purification and functionalization process of the nanotubes. The annealing procedure leads to a structural modification mainly associated with removing surface impurities as purification residues. Magnetic studies confirmed a significant contribution of Fe 3 C as evidenced by a Curie temperature estimated at T C = 452 ± 15 K. A slight change in magnetic properties upon annealing was revealed. The detailed studies performed on nanotubes are extremely important for the further synthesis of composite materials based on f-MWCNTs.

Magnetite and maghemite multicore nanoflowers (NFs) synthesized using the modified polyol-mediated routes are to date among the most effective nanoheaters in magnetic hyperthermia (MHT). Recently, magnetite NFs have also shown high photothermal (PT) performances in the most desired second near-infrared (NIR-II) biological window, making them attractive in the field of nanoparticle-activated thermal therapies. However, what makes magnetic NFs efficient heating agents in both modalities still remains an open question. In this work, we investigate the role of many parameters of the polyol synthesis on the final NFs' size, shape, chemical composition, number of cores, and crystallinity. These nanofeatures are later correlated to the magnetic, optical, and electronic properties of the NFs as well as their collective macroscopic thermal properties in MHT and PT to find relationships between their structure, properties, and function. We evidence the critical role of iron(III) and heating ramps on the elaboration of well-defined NFs with a high number of multicores. While MHT efficiency is found to be proportional to the average number of magnetic cores within the assemblies, the optical responses of the NFs and their collective photothermal properties depend directly on the mean volume of the NFs (as supported by optical cross sections numerical simulations) and strongly on the structural disorder in the NFs, rather than the stoichiometry. The concentration of defects in the nanostructures, evaluated by photoluminescence and Urbach energy ( E U ), evidence a switch in the optical behavior for a limit value of E U = 0.4 eV where a discontinuous transition from high to poor PT efficiency is also observed.

Iron oxide nanoparticles (IONPs) are well-known contrast agents for MRI for a wide range of sizes and shapes. Their use as theranostic agents requires a better understanding of their magnetic hyperthermia properties and also the design of a biocompatible coating ensuring their stealth and a good biodistribution to allow targeting of specific diseases. Here, biocompatible IONPs of two different shapes (spherical and octopod) were designed and tested in vitro and in vivo to evaluate their abilities as high-end theranostic agents. IONPs featured a dendron coating that was shown to provide anti-fouling properties and a small hydrodynamic size favoring an in vivo circulation of the dendronized IONPs. While dendronized nanospheres of about 22 nm size revealed good combined theranostic properties ( r 2 = 303 mM s -1 , SAR = 395 W g Fe -1 ), octopods with a mean size of 18 nm displayed unprecedented characteristics to simultaneously act as MRI contrast agents and magnetic hyperthermia agents ( r 2 = 405 mM s -1 , SAR = 950 W g Fe -1 ). The extensive structural and magnetic characterization of the two dendronized IONPs reveals clear shape, surface and defect effects explaining their high performance. The octopods seem to induce unusual surface effects evidenced by different characterization techniques while the nanospheres show high internal defects favoring Néel relaxation for magnetic hyperthermia. The study of octopods with different sizes showed that Néel relaxation dominates at sizes below 20 nm while the Brownian one occurs at higher sizes. In vitro experiments demonstrated that the magnetic heating capability of octopods occurs especially at low frequencies. The coupling of a small amount of glucose on dendronized octopods succeeded in internalizing them and showing an effect of MH on tumor growth. All measurements evidenced a particular signature of octopods, which is attributed to higher anisotropy, surface effects and/or magnetic field inhomogeneity induced by tips. This approach aiming at an analysis of the structure-property relationships is important to design efficient theranostic nanoparticles.

Iron carboxylates are widely used as iron precursors in the thermal decomposition process or considered as in situ formed intermediate precursors. Their molecular and three-dimensional (3D)-structural nature has been shown to affect the shape, size, and composition of the resulting iron oxide nanoparticles (NPs). Among carboxylate precursors, stearates are particularly attractive because of their higher stability to aging and hydration and they are used as additives in many applications. Despite the huge interest of iron stearates, very few studies aimed up to now at deciphering their full metal-ligand structures and the mechanisms allowing us to achieve in a controlled manner the bottom-up NP formation. In this work, we have thus investigated the molecular structure and composition of two iron stearate precursors, synthesized by introducing either two (FeSt 2 ) or three (FeSt 3 ) stearate (St) chains. Interestingly, both iron stearates consist of lamellar structures with planes of iron polynuclear complexes (polycations) separated with stearate chains in all-trans conformation. The iron content in polycations was found very different between both iron stearates. Their detailed characterizations indicate that FeSt 2 is mainly composed of [Fe 3 -(μ 3 -O)St 6 · x H 2 O]Cl, with no (or few) free stearate, whereas FeSt 3 is a mixture of mainly [Fe 7 (μ 3 -O(H)) 6 (μ 2 -OH) x St 12-2 x ]St with some [Fe 3 (μ 3 -O)St 6 · x H 2 O]St and free stearic acid. The formation of bigger polynuclear complexes with FeSt 3 was related to higher hydrolysis and condensation rates within the iron(III) chloride solution compared to the iron(II) chloride solution. These data suggested a nucleation mechanism based on the condensation of polycation radicals generated by the catalytic departure of two stearate chains from an iron polycation-based molecule.

The reactivity of iron(II/III) oxide surfaces may be influenced by their interaction with silica, which is ubiquitous in aquatic systems. Understanding the structure-reactivity relationships of Si-coated mineral surfaces is necessary to describe the complex surface behavior of nanoscale iron oxides. Here, we use Si-adsorption isotherms and Fourier transform infrared spectroscopy to analyze the sorption and polymerization of silica on slightly oxidized magnetite nanoparticles (15% maghemite and 85% magnetite, i.e., ∼2 maghemite surface layers), showing that Si adsorption follows a Langmuir isotherm up to 2 mM dissolved Si, where surface polymerization occurs. Furthermore, the effects of silica surface coatings on the redox-catalytic ability of magnetite are analyzed using selenium as a molecular probe. The results show that for partially oxidized nanoparticles and even under different Si surface coverages, electron transfer is still occurring. The results indicate anion exchange between silicate and the sorbed Se IV and Se VI . X-ray absorption near-edge structure analyses of the reacted Se indicate the formation of a mixed selenite/Se 0 surface phase. We conclude that neither partial oxidation nor silica surface coatings block the sorption and redox-catalytic properties of magnetite nanoparticles, a result with important implications to assess the reactivity of mixed-valence phases in environmental settings.

The measurement of the magneto-elastic impedance enables the magneto-mechanical coefficient of amorphous tapes, for example, to be accurately estimated. We first propose an analytical model describing the principle of a resonator based on magnetostrictive ribbons. We show how, from the impedance described by a circle in the complex plane, the characteristics of a magnetostrictive resonator can be established and estimated from the evolution of the impedance as a function of frequency. This method, which is entirely implemented with an amorphous metal ribbon (Metglas ™ 2826), is perfectly adapted to estimate the magneto-mechanical coupling coefficient k 33 and thus establish the magnetostriction curves λ(H) of amorphous ribbons. However, application to thick nickel foil shows that the current method is restricted to magnetic materials in a thin ribbon form (<∼100 µm). It should also be noted that this technique has serious advantages over those commonly used: it is non-destructive, inexpensive, and very easy to use.

Adsorption kinetics models have been used to evaluate the adsorption behaviour of pollutants on different materials but there are no reports for the adsorption of As 5+ , As 3+ , Sb 3+ and Hg 2+ on co-precipitated akaganeite nanoparticles which were previously formed in the presence of these ions. In this research, the performance of pure and co-precipitated akaganeite nanoparticles as adsorbents of As 3+ , As 5+ , Sb 3+ and Hg 2+ in aqueous solutions was evaluated using the nonlinear kinetics models of Langmuir, Lagergren, Ho-McKay, Bangham, Elovich and simplified Elovich. In addition, transmission 57 Fe Mössbauer spectrometry was used for the first time to compare the physico-chemical properties of akaganeite before and after the adsorption processes. The results showed that co-precipitated akaganeites had much better adsorption capacities than pure akaganeites. On the other hand, the Sb 3+ and Hg 2+ were the fastest and slowest pollutants respectively adsorbed on all akaganeites. The kinetics models that best described the experimental data for As 3+ , As 5+ and Sb 3+ were those of Elovich and simplified Elovich. For Hg 2+ , the kinetic model that best described the experimental data was that of Bangham. The 300 K and 77 K Mössbauer spectrometry showed only slight variations in some of the hyperfine parameters for the akaganeites after adsorption., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Core-shell magnetic nanoparticles type Fe 3- x O₄ (≈10 nm)@CoO (≈3 nm) prepared by forced hydrolysis in polyol medium have been investigated through the combined use of dc magnetization measurements by SQUID and local analysis by 57 Fe Mössbauer spectrometry. A shift of the hysteresis loop along the field axis was observed, which highlights the presence of exchange bias coupling in these nanoparticles. This exchange bias coupling is accompanied by an unexpected high value of coercive field in hysteresis loop in mode ZFC. A local probe study using both zero-field and in-field Mössbauer spectrometry reveals complex hyperfine structures. Great attention is paid to the fitting procedure: it is concluded that Fe 3- x O₄@CoO nanoparticles result from a mixture of magnetite and maghemite phases in addition to the formation of an interface-like layer close to a cobalt ferrite. Such a structure explains both the high coercive field value observed by SQUID and the presence of exchange bias coupling.

The lithium and lithium-ion battery electrode chemical stability in the pristine state has rarely been considered as a function of the binder choice and the electrode processing. In this work, X-ray photoelectron spectroscopy (XPS) and XPS imaging analyses associated with complementary Mössbauer spectroscopy are used in order to study the chemical stability of two pristine positive electrodes: (i) an extruded LiFePO 4 -based electrode formulated with different polymer matrices [polyethylene oxide and a polyvinylidene difluoride (PVdF)] and processed at different temperatures (90 and 130 °C, respectively) and (ii) a Li[Ni 0.5 Mn 0.3 Co 0.2 ]O 2 (NMC)-based electrode processed by tape-casting, followed by a mild or heavy calendering treatment. These analyses have allowed the identification of reactivity mechanisms at the interface of the active material and the polymer in the case of PVdF-based electrodes.

In the field of nanomedicine, superparamagnetic nanoparticles are one of the most studied nanomaterials for theranostics. In this study, a one-pot synthesis of magnetic nanoparticles is presented, with an increased control on particle size from 10 to 40 nm. Monitoring of vacuum level is introduced here as a crucial parameter for achieving a fine particle morphology. The magnetic properties of these nanoparticles are highly affected by disorders or mismatches in crystal structure. A prolonged oxidation step is applied to the obtained nanoparticles to transform the magnetic phases into a pure maghemite one, confirmed by high-resolution X-ray photoelectron spectroscopy analysis, by Mössbauer spectrometry and, indirectly, by increased performances in magnetization curves and in relaxation times. Afterward, the attained nanoparticles are transferred into water by a nonderivatized dextran coating. Thermogravimetric analysis confirms that polysaccharide molecules replace oleic acid on the surface by stabilizing the particles in the aqueous phase and culture media. Preliminary in vitro test reveals that the dextran-coated nanoparticles are not passively internalized from the cells. As a proof of concept, a secondary layer of chitosan assures a positive charge to the nanoparticle surface, thus enhancing cellular internalization.

Ce substituted Nd 2 Fe 14 B (2:14:1)-type permanent magnets have shown increasing potential in the applications due to their high properties/cost ratio. However, the element segregation and phase separation in the Ce substituted magnets have not been fully understood yet. In this work, (Nd 1-x Ce x ) 25 Fe 40 Co 20 Al 4 B 11 alloys with high coercivities were prepared by copper mold casting. Based on detailed microstructure and composition analysis, the segregation of rare earth (RE) elements was observed in the as-cast alloys. Nd element prefers to enter into the 2:14:1 phase and the Ce element enter into the 1:2 phase. The existence of the 1:2 phase can promote the element segregation. The alloy shows an abnormal increase of coercivity from 641 kA/m for x = 0.2 to 863 kA/m for x = 0.3. This increase could be attributed to the phase separation of the 2:14:1 phase, which has been confirmed by the microstructural characterization. The present data provides useful information for exploring Ce-containing Nd-Fe-B magnets.

Nanoparticles of Li 0.3 Zn 0.3 Co 0.1 Fe 2.3 O 4 (LZC) were prepared by the sol-gel method and dried in a furnace at ∼200 °C. The dried sample was annealed at 500, 600, 700, and 800 °C for 5 h each. Rietveld analysis of X-ray diffraction patterns confirms the cubic Fd3̅m phase formation with lattice parameters ranged from 8.376 up to 8.390 Å and allows the crystallite sizes (d cryst ) to be estimated. To enhance microwave (MW) absorption as well as the effectiveness for hyperthermia treatment, nanoparticles are taken in the matrix of multiwalled carbon nanotubes (MWCNTs) and the morphology of the so-prepared samples (LZC@MWCNT) was studied by scanning electron microscopy and transmission electron microscopy analyses. Both static and dynamic magnetic properties were investigated on the samples of LZC nanoparticles and compared to those of the samples of LZC@MWCNT. The samples annealed at 500, 600, and 800 °C are excellent candidates in cancer treatment as ac magnetic heating analysis shows that the hyperthermia temperature (42 °C) was successfully achieved for an applied ac magnetic field of 420 Oe and 300 kHz frequency. MW absorption study also reveals that the samples of LZC@MWCNT could be used as a potential MW absorbing material for which a maximum reflection loss (R L ) of ∼-21 dB was achieved at a frequency of 15.27 GHz for only 1 mm layer thickness.

With the aim of producing Au-Fe x O y dimers with outstanding heating performances under magnetic hyperthermia conditions applicable to human patients, here we report two synthesis routes, a two-pot and a one-pot method. The addition of chloride ions and the absence of 1,2-hexadecanediol (HDDOL), a commonly used chemical in this synthesis, are the key factors that enable us to produce dimers at low temperature with crystalline iron oxide domains in the size range between 18-39 nm that is ideal for magnetic hyperthermia. In the case of two-pot synthesis, in which no chloride ions are initially present in the reaction pot, dimers are obtained only at 300 °C. In order to lower the reaction temperature to 200 °C and to tune the size of the iron oxide domain, the addition of chloride ions becomes the crucial parameter. In the one-pot method, the presence of chloride ions from the start of the synthesis (as counter ions of the gold salt precursor) enables a prompt formation of dimers directly at 200 °C. In this case, the reaction time is the main parameter used to tune the iron oxide size. A record value of specific absorption rates (SARs) up to 1300 W g Fe -1 at 330 kHz and 24 kA m -1 was measured for dimers with an iron oxide domain of 24 nm in size.

Nanocrystalline samples of Ni 0.3 Zn 0.4 Co 0.2 Cu 0.1 Fe 2 O 4 (NZCCF) are prepared by a simple co-precipitation method. To obtain nanoparticles of different sizes, the as prepared sample is annealed at 400, 600, 800 and 1000 °C. Nanoparticles of the sample annealed at 600 °C are encapsulated in multi-walled carbon nanotubes (MWCNT). To confirm the crystallographic phase, x-ray diffraction (XRD) patterns are analyzed by the Rietveld method and cation distribution in A- and B-sites is estimated from the analysis. Occupancy of Zn 2+ ions in A-site and that of Fe 3+ ions in B-site increase with the increase of annealing temperature (T A ) and lattice parameters lie within 8.365-8.398 Å. Morphology of the encapsulated sample is examined by taking micrographs in high resolution transmission electron microscope (HRTEM). Hyperfine behaviour of the prepared samples is studied by analyzing Mössbauer spectra recorded at room temperature (RT) and 77 K. Average values of isomer shift (IS) are found to decrease with the increase of crystallite size. Static and dynamic magnetic hysteresis loops are recorded to analyze the magnetic properties of the sample. Maximum saturation magnetization of ~75 emu g -1 is obtained for the sample of NZCCF annealed at 800 °C with crystallite size of ~48 nm. Microwave absorption capability of the encapsulated sample is measured by recording the reflection loss in X and K u bands of microwave region of frequency. Maximum value of reflection loss is  -25.71 dB observed at 15.24 GHz for a sample layer thickness of 1 mm. Moreover, the reflection loss is less than  -10 dB for the entire range of observation (8-18 GHz) which shows that MWCNT encapsulated NZCCF could be considered as a potential candidate for applications in microwave devices.

Fe-doped La0.77Sr0.23Mn1 - y Fe y O3 nanoparticles have been synthesized by sol-gel method, and ceramic samples based on them were sintered at 1613 K. Crystallographic and magnetic properties of obtained nanoparticles and ceramic samples have been studied. It has been established that cell volume for nanoparticles increases with growing of iron content, while this dependence displays an opposite trend in the case of ceramic samples. Mössbauer investigations have shown that in all samples, the oxidation state of iron is +3. According to magnetic studies, at room temperature, both nanoparticles and ceramic samples with y ≤ 0.06 display superparamagnetic properties and samples with y ≥ 0.08 are paramagnetic. Magnetic fluids based on La0.77Sr0.23Mn1 - y Fe y O3 nanoparticles and aqua solution of agarose have been prepared. It has been established that heating efficiency of nanoparticles under an alternating magnetic field decreases with growing of iron content.

The effects of laser irradiation on γ-Fe 2 O 3 4 ± 1 nm diameter maghemite nanocrystals synthesized by co-precipitation and dispersed into an amorphous silica matrix by sol-gel methods have been investigated as function of iron oxide mass fraction. The structural properties of γ-Fe 2 O 3 phase were carefully examined by X-ray diffraction and transmission electron microscopy. It has been shown that γ-Fe 2 O 3 nanocrystals are isolated from each other and uniformly dispersed in silica matrix. The phase stability of maghemite nanocrystals was examined in situ under laser irradiation by Raman spectroscopy and compared with that resulting from heat treatment by X-ray diffraction. It was concluded that ε-Fe 2 O 3 is an intermediate phase between γ-Fe 2 O 3 and α -Fe 2 O 3 and a series of distinct Raman vibrational bands were identified with the ε-Fe 2 O 3 phase. The structural transformation of γ-Fe 2 O 3 into α -Fe 2 O 3 occurs either directly or via ε-Fe 2 O 3 , depending on the rate of nanocrystal agglomeration, the concentration of iron oxide in the nanocomposite and the properties of silica matrix. A phase diagram is established as a function of laser power density and concentration.

Ferritin has gained significant attention as a potential reporter gene for in vivo imaging by magnetic resonance imaging (MRI). However, due to the ferritin ferrihydrite core, the relaxivity and sensitivity for detection of native ferritin is relatively low. We report here on a novel chimeric magneto-ferritin reporter gene - ferritin-M6A - in which the magnetite binding peptide from the magnetotactic bacteria magnetosome-associated Mms6 protein was fused to the C-terminal of murine h-ferritin. Biophysical experiments showed that purified ferritin-M6A assembled into a stable protein cage with the M6A protruding into the cage core, enabling magnetite biomineralisation. Ferritin-M6A-expressing C6-glioma cells showed enhanced (per iron) r2 relaxivity. MRI in vivo studies of ferritin-M6A-expressing tumour xenografts showed enhanced R2 relaxation rate in the central hypoxic region of the tumours. Such enhanced relaxivity would increase the sensitivity of ferritin as a reporter gene for non-invasive in vivo MRI-monitoring of cell delivery and differentiation in cellular or gene-based therapies.

Magnetic properties of iron oxide nanoparticles with spinel structure are strictly related to a complex interplay between cationic distribution and the presence of a non-collinear spin structure (spin canting). With the aim to gain better insight into the effect of the magnetic structure on magnetic properties, in this paper we investigated a family of small crystalline ferrite nanoparticles of the formula CoxNi1-xFe2O4 (0 ≤x≤ 1) having equal size (≈4.5 nm) and spherical-like shape. The field dependence of magnetization at low temperatures indicated a clear increase of magnetocrystalline anisotropy and saturation magnetization (higher than the bulk value for CoFe2O4: ∼130 A m(2) kg(-1)) with the increase of cobalt content. The magnetic structure of nanoparticles has been investigated by Mössbauer spectroscopy under an intense magnetic field (8 T) at a low temperature (10 K). The magnetic properties have been explained in terms of an evolution of the magnetic structure with the increase of cobalt content. In addition a direct correlation between cationic distribution and spin canting has been proposed, explaining the presence of a noncollinear spin structure in terms of superexchange interaction energy produced by the average cationic distribution and vacancies in the spinel structure.

A novel synthesis of cobalt-iron layered double hydroxide (LDH) with interlayer chlorides was investigated. The method consists in mixing concentrated solutions of hexaamminecobalt(III) trichloride with ferrous chloride at room temperature and in anoxic conditions. Four initial Fe/Co atomic ratios have been tried out (0.12, 0.6, 1.2 and 1.8). Neither heating nor addition of alkali was employed for adjusting the pH and precipitating the metal hydroxides. Still, each mixture led to the spontaneous precipitation of a LDH-rich solid having a crystal-chemistry that depended on the initial solution Fe/Co. These LDHs phases were carefully characterized by mean of X-ray diffraction, (57)Fe Mössbauer spectrometry, transmission electron microscopy and chemical analysis (total dissolution and phenanthroline method). Solution Eh and pH were also monitored during the synthesis. Increasing initial Fe/Co ratio impacted the dynamic of the observed stepwise reaction and the composition of the resulting product. Once the two solutions are mixed, a spontaneous and abrupt color change occurs after an induction time which depends on the starting Fe/Co ratio. This makes the overall process acting as a chemical clock. This spontaneous generation of CoFe-LDH arises from the interplay between redox chemistries of iron and cobalt-ammonium complexes., (Copyright © 2014 Elsevier Inc. All rights reserved.)

An efficient synthesis route is proposed to obtain single phase powder ceramic of CaFe5O7. This complex structure can be described as an intergrowth between one CaFe2O4 unit and n = 3 slices of FeO Wüstite-type structure. A detailed structural study has been carried out at room temperature combining transmission electron microscopy (TEM) observations (ED, HREM), scanning transmission electron microscopy (STEM-HAADF), and X-ray diffraction data. The analysis of these data has revealed an unexpected supercell with a monoclinic symmetry. From the hkl conditions deduced from the electron diffraction study and the analysis of X-ray diffraction data by simulated annealing, a structural model considering the centrosymmetric P2₁/m setting can be proposed. In addition the first magnetic and electrical transport measurements are reported showing a sharp peak in magnetic susceptibility and a strong localization around 360 K, associated to a structural change from monoclinic setting to orthorhombic one.

This paper studied the synthesis, characterization and use of the magnetic chitosan nanogel for carrying meleimidic compounds. The hydrogel polymer was prepared using O-carboxymethylchitosan, which was crosslinked with epichlorohydrin for subsequent incorporation of iron oxide magnetic nanoparticles. The characterization revealed that the magnetic material comprises about 10% of the hydrogel. This material is comprised of magnetite and maghemite and exhibits ferro-ferrimagnetic behavior. The average particle size is 4.2 nm. There was high incorporation efficiency of maleimides in the magnetic nanogel. The release was of sustained character and there was a greater release when an external magnetic field was applied. The mathematical model that best explained the process of drug release by the magnetic hydrogel was that of Peppas-Sahlin. The magnetic nanogel proved to be an excellent candidate for use in drug-delivery systems.

Escherichia coli abatement was studied in liquid phase under visible light in the presence of two commercial titania photocatalysts, and of Fe- and Al-doped titania samples prepared by high energy ball-milling. The two commercial titania photocatalysts, Aeroxide P25 (Evonik industries) exhibiting both rutile and anatase structures and MPT625 (Ishihara Sangyo Kaisha), a Fe-, Al-, P- and S-doped titania exhibiting only the rutile phase, are active suggesting that neither the structure nor the doping is the driving parameter. Although the MPT625 UV-visible spectrum is shifted towards the visible domain with respect to the P25 one, the effect on bacteria is not increased. On the other hand, the ball milled iron-doped P25 samples exhibit low activities in bacteria abatement under visible light due to charge recombinations unfavorable to catalysis as shown by photoluminescence measurements. While doping elements are in interstitial positions within the rutile structure in MPT625 sample, they are located at the surface in ball milled samples and in isolated octahedral units according to (57)Fe Mössbauer spectrometry. The location of doping elements at the surface is suggested to be responsible for the sample cytotoxicity observed in the dark., (Copyright © 2014 Elsevier B.V. All rights reserved.)

A model was developed to describe how the 2:1 layer excess negative charge induced by the reduction of Fe(III) to Fe(II) by sodium dithionite buffered with citrate-bicarbonate is balanced and applied to nontronites. This model is based on new experimental data and extends structural interpretation introduced by a former model [36-38]. The 2:1 layer negative charge increase due to Fe(III) to Fe(II) reduction is balanced by an excess adsorption of cations in the clay interlayers and a specific sorption of H(+) from solution. Prevalence of one compensating mechanism over the other is related to the growing lattice distortion induced by structural Fe(III) reduction. At low reduction levels, cation adsorption dominates and some of the incorporated protons react with structural OH groups, leading to a dehydroxylation of the structure. Starting from a moderate reduction level, other structural changes occur, leading to a reorganisation of the octahedral and tetrahedral lattice: migration or release of cations, intense dehydroxylation and bonding of protons to undersaturated oxygen atoms. Experimental data highlight some particular properties of ferruginous smectites regarding chemical reduction. Contrary to previous assumptions, the negative layer charge of nontronites does not only increase towards a plateau value upon reduction. A peak is observed in the reduction domain. After this peak, the negative layer charge decreases upon extended reduction (>30%). The decrease is so dramatic that the layer charge of highly reduced nontronites can fall below that of its fully oxidised counterpart. Furthermore, the presence of a large amount of tetrahedral Fe seems to promote intense clay structural changes and Fe reducibility. Our newly acquired data clearly show that models currently available in the literature cannot be applied to the whole reduction range of clay structural Fe. Moreover, changes in the model normalising procedure clearly demonstrate that the investigated low tetrahedral bearing nontronites (SWa-1, GAN and NAu-1) all exhibit the same behaviour at low reduction levels. Consequently, we restricted our model to the case of moderate reduction (<30%) in low tetrahedral Fe-bearing nontronites. Our adapted model provides the relative amounts of Na(+) (p) and H(+) (ni) cations incorporated in the structure as a function of the amount of Fe reduction. Two equations enable the investigated systems to be described: p=m/(1+Kr·ω·mrel) and ni=Kr·ω·m·mrel/(1+Kr·ω·mrel); where m is the Fe(II) content, mrel, the reduction level (m/mtot), ω, the cation exchange capacity (CEC, and Kr, an empirical constant specific to the system., (Copyright © 2013 Elsevier Inc. All rights reserved.)

Arsenic contamination of floodplain soils is extensive and additional fresh arsenic inputs to the pedosphere from human activities are ongoing. We investigate the cumulative effects of repetitive soil redox cycles, which occur naturally during flooding and draining, on a calcareous fluvisol, the native microbial community and arsenic mobility following a simulated contamination event. We show through bioreactor experiments, spectroscopic techniques and modelling that repetitive redox cycling can decrease arsenic mobility during reducing conditions by up to 45%. Phylogenetic and functional analyses of the microbial community indicate that iron cycling is a key driver of observed changes to solution chemistry. We discuss probable mechanisms responsible for the arsenic immobilisation observed in-situ. The proposed mechanisms include, decreased heterotrophic iron reduction due to the depletion of labile particulate organic matter (POM), increases to the proportion of co-precipitated vs. aqueous or sorbed arsenic with α-FeOOH/Fe(OH)3 and potential precipitation of amorphous ferric arsenate., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

The effectiveness of amine-borane as reducing agent for the synthesis of iron nanoparticles has been investigated. Large (2-4 nm) Fe nanoparticles were obtained from [Fe{N(SiMe3)2}2]. Inclusion of boron in the nanoparticles is clearly evidenced by extended X-ray absorption fine structure spectroscopy and Mössbauer spectrometry. Furthermore, the reactivity of amine-borane and amino-borane complexes in the presence of pure Fe nanoparticles has been investigated. Dihydrogen evolution was observed in both cases, which suggests the potential of Fe nanoparticles to promote the release of dihydrogen from amine-borane and amino-borane moieties., (Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Measurement of the magneto-mechanical parameters characteristics of amorphous ribbons often requires complex or limited methods due to their very small thickness. In this paper, it is shown how one can establish and estimate the characteristics of a magnetostrictive resonator from the experimental frequency response free of any kind of mechanical measurement (stress or elongation). This technique which is completely developed with a ribbon exhibiting good resonator properties, is suitable to estimate the magneto-mechanical coupling coefficient k33 and the Young's modulus and also to establish the magnetostriction curves λ(H) of amorphous ribbons. Results obtained from resonators made of 2605SC and 2826 from Metglas(TM) ribbons confirmed the validity of the present technique. However, measurements performed on a thin foil of nickel demonstrate that the present method cannot be extended to semi-soft magnetic materials. The technique which is proposed, has serious advantages upon others as it is non-destructive, low cost and easy to develop compared to common ones.

In order to assess the adsorption properties of hydrogen gas and reactivity of adsorbed hydrogen, we measured H(2)(g) adsorption on Na synthetic montmorillonite-type clays and Callovo-Oxfordian (COx) clayrock using gas chromatography. Synthetic montmorillonites with increasing structural Fe(III) substitution (0 wt %, 3.2 wt %, and 6.4 wt % Fe) were used. Fe in the synthetic montmorillonites is principally present as structural Fe(III) ions. We studied the concomitant reduction of structural Fe(III) in the clays using (57)Fe Mössbauer spectrometry. The COx, which mainly contains smectite/illite and calcite minerals, is also studied together with the pure clay fraction of this clayrock. Experiments were performed with dry clay samples which were reacted with hydrogen gas at 90 and 120 °C for 30 to 45 days at a hydrogen partial pressure close to 0.45 bar. Results indicate that up to 0.11 wt % of hydrogen is adsorbed on the clays at 90 °C under 0.45 bar of relative pressure. (57)Fe Mössbauer spectrometry shows that up to 6% of the total structural Fe(III) initially present in these synthetic clays is reduced upon adsorption of hydrogen gas. No reduction is observed with the COx sample in the present experimental conditions.

CoFe(2)O(4) nanoparticles (D(NPD) ~6 nm), prepared by a thermal decomposition technique, have been investigated through the combined use of dc magnetization measurements, neutron diffraction, and (57)Fe Mössbauer spectrometry under high applied magnetic field. Despite the small particle size, the value of saturation magnetization at 300 K (M(s) ͠= 70 A m(2) kg(-1)) and at 5 K (M(s) ͠= 100 A m(2) kg(-1)) are rather close to the bulk values, making the samples prepared with this method attractive for biomedical applications. Neutron diffraction measurements indicate the typical ferrimagnetic structure of the ferrites, showing an inversion degree (γ(NPD) = 0.74) that is in very good agreement with cationic distribution established from low temperature (10 K) Mössbauer measurements in high magnetic field (γ(moss) = 0.76). In addition, the in-field Mössbauer spectrum shows the presence of a non-collinear spin structure in both A and B sublattices. The results allow us to explain the high value of saturation magnetization and provide a better insight into the complex interplay between cationic distribution and magnetic disorder in ferrimagnetic nanoparticles., (© 2011 IOP Publishing Ltd)

Magnetic N-benzyl-O-carboxymethylchitosan nanoparticles were synthesized through incorporation and in situ methods and characterized by Fourier transform infrared spectroscopy, X-ray diffraction, differential scanning calorimetry, and magnetization measurements. Indomethacin was incorporated into the nanoparticles via the solvent evaporation method. The indomethacin-loaded magnetic nanoparticles were characterized by the same techniques, and also by transmission electron microscopy. The nanoparticles containing the polymer showed a drug loading efficiency of between 60.8% and 74.8%, and the magnetic properties were not significantly affected by incorporation of the drug. The in vitro drug release study was carried out in simulated body fluid, pH 7.4 at 37°C. The profiles showed an initial fast release, which became slower as time progressed. The percentage of drug released after 5 h was between 60% and 90%, and the best fitting mathematical model for drug release was the Korsmeyer-Peppas model, indicating a Fickian diffusion mechanism., (Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

It was reported the adsorption of As(III) on the surface of the chitosan-Fe-crosslinked complex. Theoretical correlation of the experimental equilibrium adsorption data for As(III)/Ch-Fe system is best explained by the non-linearized form Langmuir-Freundlich isotherm model. At optimum conditions, pH 9.0, the maximum adsorption capacity, calculated using the Langmuir-Freundlich isotherm model was 13.4 mg g⁻¹. The adsorption kinetics of As(III) onto Ch-Fe are described by the pseudo-first-order kinetic equation. The results of the Mössbauer spectroscopy showed that there is no redox process on the surface of the adsorbent., (Copyright © 2010 Elsevier Ltd. All rights reserved.)

The grafting of pegylated dendrons on 9(2) nm and 39(5) nm iron oxide nanoparticles in water, through a phosphonate group as coupling agent has been successfully achieved and its mechanism investigated, with a view to produce biocompatible magnetic nano-objects for biomedical applications. Grafting has been demonstrated to occur by interaction of negatively charged phosphonate groups with positively charged groups and hydroxyl at the iron oxide surface. The isoelectric point of the suspension of dendronized iron oxide nanoparticles is shifted towards lower pH as the amount of dendron increases. It reaches 4.7 for the higher grafting rate and for both particle size. Thus, the grafting of molecules using a phosphonate group allows stabilizing electrostatically the suspensions at physiological pH, a prerequisite for biomedical applications. Moreover the grafting step has been shown to preserve the magnetic properties of iron oxide nanoparticles due to super-super exchange interactions through the phosphonate group.

Mn ferrite (MnFe(2)O(4)) nanoparticles, having diameters from 4 to 50 nm, were synthesized using a modified co-precipitation technique in which mixed metal chloride solutions were added to different concentrations of boiling NaOH solutions to control particle growth rate. Thermomagnetization measurements indicated an increase in Néel temperature corresponding to increased particle growth rate and particle size. The Néel temperature is also found to increase inversely proportionally to the cation inversion parameter, delta, appearing in the formula (Mn(1-delta)Fe(delta))(tet)[Mn(delta)Fe(2-delta)](oct)O(4). These results contradict previously published reports of trends between Néel temperature and particle size, and demonstrate the dominance of cation inversion in determining the strength of superexchange interactions and subsequently Néel temperature in ferrite systems. The particle surface chemistry, structure, and magnetic spin configuration play secondary roles.

The iron crosslinked chitosan (Ch-Fe-CL) and N-carboxylmethyl chitosan (N-CM-Ch-Fe) complexes were studied by complementary techniques: structurally sensitive Mössbauer and X-ray absorption methods, as well as static magnetic measurements. A detailed and consistent description of these complexes including, besides the overall magnetic behavior, the spin ordering and local atomic structure around Fe ions is presented. Fe atoms in the investigated samples are mostly penta-coordinated and appear in a high spin Fe (3+) ionic state. In Ch-Fe-CL, two kinds of Fe near neighbors are equally probable and several Fe atoms are situated in the second coordination sphere. The magnetic interactions between these Fe ions lead to a sperimagnetic-like ordering. In N-CM-Ch-Fe, only one Fe neighborhood was found. Other Fe atoms were identified neither in the first nor in the second coordination sphere, but the third coordination sphere indicates the presence of Fe atoms. The magnetic coupling between these atoms is antiferromagnetic, but the dominant part of Fe in this sample remains in a paramagnetic state.

The effect of Mn and B on the magnetic and structural properties of nanostructured samples of the Fe60Al40 system, prepared by mechanical alloying, was studied by 57Fe Mössbauer spectrometry, X-ray diffraction and magnetic measurements. In the case of the Fe(60-x)Mn(x)Al40 system, 24 h milling time is required to achieve the BCC ternary phase. Different magnetic structures are observed according to the temperature and the Mn content for alloys milled during 48 h: ferromagnetic, antiferromagnetic, spin-glass, reentrant spin-glass and superparamagnetic behavior. They result from the bond randomness behaviour induced by the atomic disorder introduced by the MA process and from the competitive interactions of the Fe-Fe ferromagnetic interactions and the Mn-Mn and Fe-Mn antiferromagnetic interactions and finally the presence of Al atoms acting as dilutors. When B is added in the Fe60Al40 alloy and milled for 12 and 24 hours, two crystalline phases were found: a prevailing FeAl BCC phase and a Fe2B phase type. In addition, one observes an additional contribution attributed to grain boundaries which increases when both milling time and boron composition increase. Finally Mn and B were added to samples of the Fe60Al40 system prepared by mechanical alloying during 12 and 24 hours. Mn content was fixed to 10 at.% and B content varied between 0 and 20 at.%, substituting Al. X-ray patterns show two crystalline phases, the ternary FeMnAl BCC phase, and a (Fe,Mn)2B phase type. The relative proportion of the last phase increases when the B content increases, in addition to changes of the grain size and the lattice parameter. Such behavior was observed for both milling periods. On the other hand, the magnetic hyperfine field distributions show that both phases exhibit chemical disorder, and that the contribution attributed to the grain boundaries is less important when the B content increases. Coercive field values of about 10(2) Oe slightly increase with boron content. Comparison with previous results on FeAIB alloys shows that Mn promotes the structural stability of the nanostructured powders.

The removal of As(V), one of the most poisonous groundwater pollutants, by synthetic nanoscale zero-valent iron (NZVI) was studied. Batch experiments were performed to investigate the influence of pH, adsorption kinetics, sorption mechanism, and anionic effects. Field emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Mossbauer spectroscopy were used to characterize the particle size, surface morphology, and corrosion layer formation on pristine NZVI and As(V)-treated NZVI. The HR-TEM study of pristine NZVI showed a core-shell-like structure, where more than 90% of the nanoparticles were under 30 nm in diameter. Mössbauer spectroscopy further confirmed its structure in which 19% were in zero-valent state with a coat of 81% iron oxides. The XRD results showed that As(V)-treated NZVI was gradually converted into magnetite/maghemite corrosion products over 90 days. The XPS study confirmed that 25% As(V) was reduced to As(III) by NZVI after 90 days. As(V) adsorption kinetics were rapid and occurred within minutes following a pseudo-first-order rate expression with observed reaction rate constants (Kobs) of 0.02-0.71 min(-1) at various NZVI concentrations. Laser light scattering analysis confirmed that NZVI-As(V) forms an inner-sphere surface complexation. The effects of competing anions revealed that HCO3-, H4SiO4(0), and H2PO4(2-) are potential interfering agents in the As(V) adsorption reaction. Our results suggest that NZVI is a suitable candidate for As(V) remediation.

Previous experimental studies on clay potentiometric titration have been unable to distinguish inorganic cation exchange in the interlayer and on basal plane surfaces from specific pH-dependent sorption of cations and anions on the edges. In this study, we refined a titration technique, combining discontinuous backtitration and cation exchange capacity (CEC) measurements, and applied it to the potentiometric titration of Na- and Ca-conditioned montmorillonites. This technique can be used to accurately measure cation exchange, edge surface proton charge, dissolution of clay, and precipitation of new phases. Thus, a precise measurement of the variations of net proton surface charge is possible. This has important implications for clay surface modeling (see part II of this article) and for processes that depend on the clay surface charge, e.g., alteration, rheological processes, and contamination retention applications. In addition, this study confirms the adsorption of ionic pairs such as CaCl+ in exchange site positions and shows that CaOH+ could behave like CaCl+. This result, together with the evidence of precipitation of a Ca?Si phase over a short time-scale (1 week) at high pH and low temperature, can be used to model clay-concrete interactions more accurately. We confirmed and quantified the H+/Na+ exchange reaction at low pH. Finally, we demonstrate that both the edge surface charge and the permanent structural charge are compensated for by the nonspecific sorption of cations from solution across the entire pH range from 4 to 11. Under these conditions, the surface potential is fully screened and does not need to be invoked in modeling sorption processes on clay particles in dilute suspensions.