Search

Thermal camouflage is a highly coveted technology aimed at enhancing the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties, and compatibility with stealth applications. Among these, graphene and graphene-like materials are the most appealing 2D materials for thermal camouflage applications. In multilayer graphene (MLG), charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG's optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically driven reduction of emissivity lowers the apparent temperature of a surface, aligning it with the background temperature to achieve thermal camouflage. This characteristic is shared by other graphene-based materials. In this review, we focus on recent advancements in the thermal camouflage properties of graphene in composite films and aerogel structures. We provide a summary of the current understanding of how thermal camouflage materials work, their present limitations, and future opportunities for development. [ABSTRACT FROM AUTHOR]

The use of 3D printing technology for manufacturing new products based on sustainable materials enables one to take advantage of secondary raw materials derived from recycling. This work investigates the structural performances of 3D printing composite filaments based on polylactic acid (PLA), as a matrix, reinforced by recycled carbon fiber (rCF). Carbon fibers were recovered from industrial scraps by a patented thermal process and used to produce thermoplastic composite filaments for additive manufacturing without any additional treatment and additives. The influence of the recovered carbon fiber (rCF) content on the thermal properties, mechanical properties and microstructure of the composites was studied in the range of 3–20 wt%. The recorded TGA curves exhibited a one-stage weight loss within the temperature range 290–380 °C for all samples and the residual rCF content was in good agreement with the theoretical fiber loading. The Young modulus of the extruded filaments strongly increased below a critical content (5 wt%), while at higher content the improvement was reduced. An increase in the storage modulus of 54% compared to neat PLA 3D printed sample resulted in a printed specimen with a higher rCF content. SEM images highlighted a strong rCF prevailing alignment in the direction of the extrusion flow, creating almost unidirectional reinforcement inside the filament. These findings suggest that homogeneous composite filaments reinforced with well-dispersed recycled CF without additional chemical modification and additives are suitable materials for additive manufacturing. The effect of rCF topological distribution within the material on the mechanical performances has been discussed, highlighting that the isolated fibers could efficiently transfer loads with respect to the percolated 3D network and have been correlated with the microstructure. [ABSTRACT FROM AUTHOR]

Among the various architectures developed for composite materials, nanolaminated architecture is a promising candidate for the design of new materials for structural and functional applications. Nanolaminates mimic the natural occurring architecture of nacre and it is formed by highly oriented nanolaminae connected by a very low amount of matrix. Due to their architecture, inherently impermeable to fluid, such kind of materials is difficult to manufacture unless using layer-by-layer processes. Here, we describe the fabrication of films with nanolaminated architecture containing very high content (>80% w/w) of graphite nanoplatelets (GNPs) within an uncured epoxy matrix (prepregs), suitable for the conventional prepregs manufacturing technologies: film stacking and consolidation under temperature under pressure. Nanolaminated prepregs have been manufactured through the deposition of a paste of GNPs in epoxy enriched acetone solvent. Mainly, scanning electron microscopy has investigated the nanolaminated architecture of the prepregs. Stress-strain behavior of nanolaminated prepregs has been investigated as a function of their composition and consolidation pressure. Finally, a laminate made of six nanolaminated prepregs (about 0.3 mm thick) has been manufactured by hot pressing revealing interesting mechanical properties: a tensile modulus of 30 GPa and a damping coefficient, tan [delta], of 0.03., INTRODUCTION Nanolaminates, consisting of the assemblies of highly oriented nanometric thin laminae, are an emerging class of nanocomposite materials at a very high percentage of reinforcing phase >70% that represent [...]

In this work, we describe the recovery of cellulose acetate (r-CA) polymer from waste cigarette butts (CBs) and their subsequent conversion into feedstock for 3D printing technology. The extraction process for CBs includes two stages: initial washes in water, followed by additional washes in ethanol. A final step involves a dissolution and reprecipitation process, resulting in the creation of a fine powder. The recovery polymer has been analysed and compared to commercial cellulose acetate (p-CA) and unsmoked cigarette filter (u-CA) to assess its purity and examine alterations in its physicochemical properties. The CA powder has also been plasticized with different biocompatible plasticizers to improve the mechanical properties of the CA. We analyze the rheological properties to identify the suitable composition as feedstock for 3D printing. [ABSTRACT FROM AUTHOR]

The need to recycle carbon-fibre-reinforced composite polymers (CFRP) has grown significantly to reduce the environmental impact generated by their production. To meet this need, thermoreversible epoxy matrices have been developed in recent years. This study investigates the performance of an epoxy vitrimer made by introducing a metal catalyst (Zn2+) and its carbon fibre composites, focusing on the healing capability of the system. The dynamic crosslinking networks endow vitrimers with interesting rheological behaviour; the capability of the formulated resin (AV-5) has been assessed by creep tests. The analysis showed increased molecular mobility above a topology freezing temperature (Tv). However, the reinforcement phase inhibits the flow capability, reducing the flow. The fracture behaviour of CFRP made with the vitrimeric resin has been investigated by Mode I and Mode II tests and compared with the conventional system. The repairability of the vitrimeric CFRP has been investigated by attempting to recover the delaminated samples, which yielded unsatisfactory results. Moreover, the healing efficiency of the modified epoxy composites has been assessed using the vitrimer as an adhesive layer. The joints were able to recover about 84% of the lap shear strength of the pristine system. [ABSTRACT FROM AUTHOR]