Search

This study aimed to compare the fracture resistance of galvano-ceramic crowns with metal-ceramic crowns cemented to natural premolar teeth with different luting cements. Sixty intact maxillary premolars were prepared to receive full-coverage crown restorations and were divided into 2 equal groups (n = 30): galvano-ceramic crowns and metal-ceramic crowns. Each group was further subdivided into 3 equal subgroups (n = 10) according to the luting cement used: zinc-phosphate, glass-ionomer, or adhesive-resin cement. The specimens were then compressively loaded until failure in a universal testing machine. The metal-ceramic crowns exhibited higher resistance to fracture compared to galvano-ceramic crowns, but both exceeded the normal documented values of occlusal masticatory forces. [ABSTRACT FROM AUTHOR]

Objectives: This study aimed to evaluate the maximum bite force (MBF) and satisfaction of patients restored with implants, combined tooth-implants, and teeth-supported monolithic zirconia fixed dental prostheses (FDPs)., Materials and Methods: Thirty partially edentulous patients in need of three units of FDPs in their mandibular posterior region were divided into three equal groups (n = 10) as follows: Group-1 patients received two implants for each at the second premolar and second molar regions, Group-2 patients received one implant for each at the second molar region, and Group-3 patients with missing lower first molar. All the restorations were constructed from monolithic zirconia. Patients were evaluated 1 week after placement of restorations (baseline) and then after 6, 12, and 24-month intervals for MBF using force transducer occlusal force meter and satisfaction (function, esthetic, and overall satisfaction) using a visual analog scale., Results: The mean MBF for Group 1 was higher than Group 2 (p = .044) but not that of Group 3 (p = .923). Additionally, Group 3 displayed a higher MBF than Group 2, although this difference was not statistically significant (p = .096). Concerning patient satisfaction, all study groups reported high levels of satisfaction across all satisfaction elements, and no significant differences were observed between the groups., Conclusion: Within the limitations of this study, it can be concluded that Group 1 gives comparable anticipated treatment outcomes as Group 3 concerning biting force and patient satisfaction. However, Group 2 gives comparable satisfaction results with biting force value within the normal range; thus, it might be used as a treatment option in a specific situation., (© 2023 The Authors. Clinical and Experimental Dental Research published by John Wiley & Sons Ltd.)

We sought to evaluate immediate and delayed micro-tensile bond strength of Panavia F2.0 and Multilink Sprint resin cement to superficial, deep and cervical dentin. Thirty-six freshly extracted non-carious human molars were sectioned in the mesiodistal direction to expose three different dentin regions including superficial dentin (1 mm below the dentine-enamel junction), deep dentin (1 mm above the highest pulp horn) and cervical dentin (0.5 mm above the cemento-enamel junction and 0.5 mm below the dentine-enamel junction). Resin cements were applied on dentin surfaces and composite blocks were luted under constant seating pressure. Each group was divided into three subgroups according to time intervals. Specimens were sectioned to obtain sticks of 1 mm(2) in diameter and subjected to microtensile bond strength testing at a cross head speed of 1 mm/min. Both resin cements showed higher micro-tensile bond strength to superficial dentin than that to deep or cervical dentin (P < 0.001). Micro-tensile bond strengths of Panavia F2.0 were higher than those of Multilink Sprint at different dentin regions (P < 0.001). Immediate micro-tensile bond strengths were higher than those of delayed micro-tensile bond strengths for both resin cements (P < 0.001). It was concluded that resin cements with different chemical formulations and applications yield significantly different micro-tensile bond strengths to different dentin regions.

Objectives: The aim of this study was to evaluate the internal adaptation and marginal properties of ceramic laminate veneers fabricated using pressable and machinable CAD/CAM techniques., Materials and Methods: 40 ceramic laminate veneers were fabricated by either milling ceramic blocks using a CAD/CAM system (group 1 n=20) or press-on veneering using lost wax technique (group 2 n=20). The veneers were acid etched using hydrofluoric acid, silanated, and cemented on their corresponding prepared teeth. All specimens were stored under water (37 °C) for 60 days, then received thermocycling (15,000 cycles between 5 and 55 °C and dwell time of 90 s) followed by cyclic loading (100,000 cycles between 50 and 100 N) before immersion in basic fuchsine dye for 24 h. Half of the specimens in each group were sectioned in labio-lingual direction and the rest were horizontally sectioned using precision cutting machine (n=10). Dye penetration, internal cement film thickness, and vertical and horizontal marginal gaps at the incisal and cervical regions were measured (α=0.05)., Results: Pressable ceramic veneers demonstrated significantly lower (F=8.916, P<0.005) vertical and horizontal marginal gaps at the cervical and incisal margins and lower cement film thickness (F=50.921, P<0.001) compared to machinable ceramic veneers. The inferior marginal properties of machinable ceramic veneers were associated with significantly higher microleakage values., Conclusions: Pressable ceramic laminate veneers produced higher marginal adaptation, homogenous and thinner cement film thickness, and improved resistance to microleakage compared to machinable ceramic veneers., Clinical Significance: The manufacturing process influences internal and marginal fit of ceramic veneers. Therefore, dentist and laboratory technicians should choose a manufacturing process with careful consideration., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Purpose: To evaluate the influence of dynamic fatigue on fracture load and failure mode of different types of adhesive zirconia restorations., Materials and Methods: Eighty adhesive cantilever fixed dental prostheses (CFDP) were fabricated and assigned to four equal groups (n = 20) using the following materials and techniques. Group 1: machine copy-milling zirconia (Cercon), group 2: manual copy-milling technique (ZirkonZahn), group 3: slip casting technique (Vita In-ceram Zirconia), group 4: metal-ceramic CFDP. Specimens in groups 1and 2 received selective infiltration-etching surface treatment, specimens in group 3 were acid etched with hydrofluoric acid and silanated, while those of group 4 were airborne particle abraded. All specimens were bonded with resin cement (Panavia F2.0) and thermocycled (5000 cycles/ 5 to 55°C). Then, half the number of the specimens of each group (n = 10) underwent dynamic loading (one million cycles at alternating loads between 10 and 40 N in a water bath at 37°C). All specimens were subjected to one-cycle loading to failure to evaluate fracture resistance. One-way and two-way ANOVA and Bonferroni post-hoc tests were used to analyze the data (α = 0.05). The intaglio surfaces of fractured specimens were examined using stereomicroscopy and scanning electron microscope (SEM)., Results: Statistical analysis revealed that the failure load of metal (413 ± 26 N) and machine copy-milled zirconia (368 ± 24 N) restorations was significantly higher (F = 129, p < 0.001) than manually copy-milled (316 ± 18) and In-ceram zirconia (210 ± 17) restorations. Dynamic fatigue significantly (p < 0.03) reduced failure load of the manually copy-milled and In-ceram zirconia restorations, while metal and machine copy-milling zirconia restorations were not influenced by fatigue., Conclusions: The fatigue strength of adhesive zirconia restorations is influenced by cyclic loading and the technique used to manufacture these restorations.

The orthodontist is often faced with the problem of bonding brackets to ceramic restorations. The purpose of this study was to find the most reliable method for bonding ceramic brackets onto ceramic crowns.

Purpose: To investigate the influence of uremia on the shear bond strength (SBS) of composite resin to enamel and dentin substrates with assessment of the micromorphological pattern of etched enamel and dentin surfaces using atomic force microscopy (AFM)., Materials and Methods: A total of 44 natural molars was collected from healthy individuals (n=22 molars) and uremic patients (n=22 molars). Each set of teeth was then divided into 2 equal subsets (n=11 molars) relative to the bonding substrate to be tested. In each subset, the surfaces of 7 molars were flattened and polished up to 2000-grit roughness using wet silicon carbide (SIC) abrasive papers. A three-step adhesive was used to bond Tetric Ceram composite buildups to the prepared tooth surfaces. All specimens were thermocycled before they were stressed in shear using a universal testing machine. Fractured specimens were stereomicroscopically examined to detect the mode of bond failure. In the remaining 4 molars, enamel and dentin specimens were prepared for AFM examination to assess the micromorphological patterns of acid-etched surfaces., Results: The mean bond strength values in MPa to enamel (22.40 +/- 4.30) and dentin (17.97 +/- 4.65) of teeth of healthy individuals were significantly different (p < 0.001) from those to enamel (12.40 +/- 2.81) and dentin (7.83 +/- 2.05) of teeth of uremic patients. Most of the tested enamel specimens showed a mixed type of bond failure, but the adhesive type was predominant with dentin specimens. AFM examinations revealed a shallow etching pattern for uremic enamel and dentin specimens compared to those of healthy individuals. The mean roughness average (Ra) values after etching of healthy enamel (238.0 +/- 4.65) and dentin (267.0 +/- 4.79) were significantly different (p < 0.001) from those to etched uremic enamel (111.0 +/- 5.24) and dentin (143.0 +/- 2.16)., Conclusion: Uremia adversely affects bonding of composite resin to enamel and dentin and confers an altered micromorphological etching pattern.