Search

Utilization of inorganic waste, if included in composite material, can be beneficial in reducing the accumulation of waste, which could help in resolving problems of disposal. beside from that, incorporating waste into composite materials also reduces the overall cost of the composites as a whole. The study examines the impact of dolomite content on the mechanical properties of the composites. Increasing the amount of dolomite in the composite significantly weakens its flexural strength, falling from 42.4 MPa at 0 % dolomite to 28.7 MPa at 15 % dolomite. Composite tensile strength also decreases by up to 25.8 % with rising dolomite dust concentration. Additionally, dolomite increases interlaminar shear strength (ILSS), with EDH15 composites showing the highest improvement. Dolomite dust in epoxy‐based composites increases the hardness value from 85 HRL to 95 HRL with an increase in dolomite dust content. The erosion test perform on air jet tester shows lowest wear rate was achieved under the following conditions: 10 % dolomite dust weight, 30° impingement angle, 10 m s−1 impact velocity, and 150 μm erodent size. Furthermore, scanning electron microscopy was used to examine the damaged, eroded surfaces for assumed wear mechanisms. [ABSTRACT FROM AUTHOR]

The natural and synthetic fibers are combined in a single composite to achieve a balance between the desired strength and cost considerations. In this study, the vacuum resin transfer moulding process was used to prepare an epoxy‐based composite. The composite consisted of grewia optiva as the natural fiber and glass fiber as the synthetic fiber, both with a fixed weightage of 10 %. Dolomite was used as a filler with varying content (0 %, 5 %, 10 %, and 15 weight %). The physical, mechanical, erosion wear and morphological behavior of the epoxy‐based composite were investigated. The inclusion of dolomite filler significantly increased the composite hardness and impact strength but reduced its tensile and flexural strength. At a dolomite filler content of 10 weight %, the erosive wear was reduced, while it increased at higher dolomite filler contents. The composite was examined using the L16 array, and the minimum wear rate was observed at an impingement angle of 30°, a velocity of 10 m/s, and an erodent size of 150 μm. Morphological studies were conducted to explore the possible mechanism for the variation in erosive wear at different dolomite contents in the hybrid composites. [ABSTRACT FROM AUTHOR]

In the present scenario, the research is now being focused on the naturally occurring polymers that can gradually replace the existing synthetic polymers for the development of bio composites having applications in medical surgeries and human implants. With promising mechanical properties and bio compatibility with human tissues, poly lactic acid (PLA) is now being viewed as a future bio material. In order to examine the applicability of PLA in human implants, the current article sheds light on the synthesis of PLA and its various copolymers used to alter its physical and mechanical properties. In the latter half, various processes used for the fabrication of biomaterials are discussed in detail. Finally, biomaterials that are currently in use in the field of biomedical (Scaffolding, drug delivery, tissue engineering, medical implants, derma, cosmetics, medical surgeries, and human implants) are represented with respective advantages in the sphere of biomaterials.

Composite materials are emerging as a vital entity for the sustainable development of both humans and the environment. Polylactic acid (PLA) has been recognized as a potential polymer candidate with attractive characteristics for applications in both the engineering and medical sectors. Hence, the present article throws lights on the essential physical and mechanical properties of PLA that can be beneficial for the development of composites, biocomposites, films, porous gels, and so on. The article discusses various processes that can be utilized in the fabrication of PLA-based composites. In a later section, we have a detailed discourse on the various composites and nanocomposites-based PLA along with the properties' comparisons, discussing our investigation on the effects of various fibers, fillers, and nanofillers on the mechanical, thermal, and wear properties of PLA. Lastly, the various applications in which PLA is used extensively are discussed in detail.

The reinforcement of natural fibre and fillers in polymer resin is the latest trend followed by research groups and industries for the development of sustainable composites. Basalt fibre and waste marble powder are naturally occurring substances used to enhanced polymer properties. The present research examined the effect of both basalt fibre and waste marble powder in epoxy resin. The hand lay-up method was employed to fabricate the composite and test for mechanical and wear behaviour. The tensile, flexural, and impact energy were enhanced up to 7.5 wt. % of WMP, and the Vickers hardness of epoxy enhanced every state of reinforcement of WMP. The specific wear rate was observed to be increased with the addition of WMP until 7.5 wt. %. Scanning electron microscopy was performed to examine the nature of fractured surface wear phenomena.

In polymer composites, synthetic fibers are primarily used as a chief reinforcing material, with a wide range of applications, and are therefore essential to study. In the present work, we carried out the erosive wear of natural and synthetic fiber-based polymer composites. Glass fiber with jute and Grewia optiva fiber was reinforced in three different polymer resins: epoxy, vinyl ester and polyester. The hand lay-up method was used for the fabrication of composites. L 16 orthogonal array of Taguchi method used to identify the most significant parameters (impact velocity, fiber content, and impingement angle) in the analysis of erosive wear. ANOVA analysis revealed that the most influential parameter was in the erosive wear analysis was impact velocity followed by fiber content and impingement angle. It was also observed that polyester-based composites exhibited the highest erosive wear followed by vinyl ester-based composites, and epoxy-based composites showed the lowest erosive wear. From the present study, it may be attributed that the low hardness of the polyester resulting in low resistance against the impact of erodent particles. The SEM analysis furthermore illustrates the mechanism took place during the wear examination of all three types of composites at highest fiber loading. A thorough assessment uncovers brittle fractures in certain regions, implying that a marginal amount of impact forces was also acting on the fabricated samples. The developed fiber-reinforced polymer sandwich composite materials possess excellent biocompatibility, desirable promising properties for prosthetic, orthopaedic, and bone-fracture implant uses.