Search

The ISS-based Calorimetric Electron Telescope (CALET) is directly measuring the energy spec- trum of electron+positron cosmic rays up to 20 TeV. Cosmic-ray electrons of TeV region energy are limited by energy loss to a propagation range of about 1 kpc, therefore the expected sources are a few nearby supernova remnants (SNR), with the Vela SNR dominating the spectrum. The latest spectrum measured by CALET in combination with the positron-only flux published by AMS-02 is fitted with a comprehensive model including nearby pulsars as the source of the positron excess. This model is extended to the TeV region by addition of the flux from the Vela SNR as calculated with DRAGON, with the integrated energy emitted in electron cosmic rays by the SNR as a variable scale factor. Exploring various scenarios for the time and energy dependence of the cosmic-ray release from Vela, under varied propagation conditions, best-fitting interpretations of the spectrum and upper limits on the emission of cosmic-ray electrons by Vela have been derived.

The Calorimetric Electron Telescope (CALET), in operation on the International Space Station since 2015, collected a large sample of cosmic-ray iron over a wide energy interval. In this Letter a measurement of the iron spectrum is presented in the range of kinetic energy per nucleon from 10 GeV/n to 2.0 TeV/n allowing the inclusion of iron in the list of elements studied with unprecedented precision by space-borne instruments. The measurement is based on observations carried out from January 2016 to May 2020. The CALET instrument can identify individual nuclear species via a measurement of their electric charge with a dynamic range extending far beyond iron (up to atomic number Z=40). The energy is measured by a homogeneous calorimeter with a total equivalent thickness of 1.2 proton interaction lengths preceded by a thin (3 radiation lengths) imaging section providing tracking and energy sampling. The analysis of the data and the detailed assessment of systematic uncertainties are described and results are compared with the findings of previous experiments. The observed differential spectrum is consistent within the errors with previous experiments. In the region from 50 GeV/n to 2 TeV/n our present data are compatible with a single power law with spectral index -2.60±0.03.

The direct observation of high-energy cosmic rays, up to the PeV energy region, will increasingly rely on highly performing calorimeters, and the physics performance will be primarily determined by their geometrical acceptance and energy resolution. Thus, it is extremely important to optimize their geometrical design, granularity and absorption depth, with respect to the totalmass of the apparatus, which is amongst the most important constraints for a space mission. CaloCube is an homogeneous calorimeter whose basic geometry is cubic and isotropic, obtained by filling the cubic volume with small cubic scintillating crystals. In this way it is possible to detect particles arriving from every direction in space, thus maximizing the acceptance. This design summarizes a three-year R&D activity, aiming to both optimize and study the full-scale performance of the calorimeter, in the perspective of a cosmic-ray space mission, and investigate a viable technical design by means of the construction of several sizable prototypes. A large scale prototype, made of a mesh of 5x5x18 CsI(Tl) crystals, has been constructed and tested on high-energy particle beams at CERN SPS accelerator. In this paper we describe the CaloCube design and present the results relative to the response of the large scale prototype to electrons., 24 pages, 19 figures

In this paper we present a position-sensitive detector based on the vertical integration of pairs of aligned pixels operating in Geiger-mode regime and designed for charged particle detection. This novel device exploits the coincidence between two simultaneous avalanche events to discriminate between particle-triggered detections and dark counts. This concept allows to have a reduced material budget and low power consumption in spite of a high granularity and fast timing response. A proof-of-principle prototype was designed and fabricated in a 150 nm CMOS process and vertically integrated through bump bonding. This first demonstrator has been characterized and tested with a high energy particle beams at CERN SPS/PS facilities, in different configurations, featuring a reduction of the dark-count rate (DCR) at room temperature from ∼ 100 kHz/mm 2 to about 24 Hz/mm 2 a particle detection efficiency limited only by the geometric factor. The device radiation tolerance has been investigated, via irradiation of single tiers with 10 keV X-rays up to a dose of 1 Mrad (SiO2) and with neutrons up to a fluence of 1011 cm−2. A second prototype, addressing the goal to improve the present fill-factor, has been designed, manufactured and approaches now the characterization phase. Potential applications of this sensor include high spatial resolution tracking in high-energy experiments, radiation monitoring in space and radiation imaging in nuclear medicine. A small hand-held demonstrator is under construction for radio-guided surgery.

A prototype of a Focused Internal Reflection Cherenkov, equipped with 16 arrays of NUV-SiPM, was tested at CERN SPS in March 2015 with beams of relativistic ions at 13, 19 and 30 GeV/n obtained from fragmentation of an Ar primary beam. The detector, designed to identify cosmic nuclei, features a Fused Silica radiator bar optically connected to a cylindrical mirror of the same material and an imaging focal plane of dimensions ∼4 cm×3 cm covered with a total of 1024 SiPM photosensors. Thanks to the outstanding performance of the SiPM arrays, the detector could be operated in photon counting mode as a fully digital device. The Cherenkov pattern was recorded together with the total number of detected photoelectrons increasing as Z 2 as a function of the atomic number Z of the beam particle. In this paper, we report on the characterization and test of the SiPM arrays and the performance of the Cherenkov prototype for the charge identification of the beam particles.

The CALorimetric Electron Telescope (CALET) space experiment, which has been developed by Japan in collaboration with Italy and the United States, is a high-energy astroparticle physics mission on the International Space Station (ISS). The primary goals of the CALET mission include investigation of possible nearby sources of high-energy electrons, detailed study of galactic cosmic-ray acceleration and propagation, and search for dark matter signatures. With a long-term observation onboard the ISS, the CALET experiment measures the flux of cosmic-ray electrons (including positrons) up to 20 TeV, gamma-rays to 10 TeV, and nuclei up to 1,000 TeV based on its charge separation capability from Z = 1 to 40. Since the start of science operation in mid-October, 2015, a continuous observation has been maintained without any major interruptions. The number of triggered events over 10 GeV is nearly 20 million per month. By using the data obtained during the first two-years, here we present a summary of the CALET observations: 1) Electron+positron energy spectrum, 2) Nuclei analysis, 3) Gamma-ray observation with a characterization of the on-orbit performance. The search results for the electromagnetic counterparts of LIGO/Virgo gravitational wave events are also discussed.

著者人数: CALET Collaboration 100名 (所属. 宇宙航空研究開発機構宇宙科学研究所(JAXA)(ISAS): 海老沢, 研; 福家, 英之; 森, 国城; 西村, 純; 高柳, 昌弘; 冨田, 洋; 上野, 史郎), Number of authors: 100 (Affiliation. Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency (JAXA)(ISAS): Ebisawa, Ken; Fuke, Hideyuki; Mori, Kunishiro; Nishimura, Jun; Takayanagi, Masahiro; Tomida, Hiroshi; Ueno, Shiro), 資料番号: SA1190040000

Precise measurements of the energy spectra and of the composition of cosmic rays in the PeV region could improve our knowledge regarding their origin, acceleration mechanism, propagation, and composition. At the present time, spectral measurements in this region are mainly derived from data collected by ground-based detectors, because of the very low particle rates at these energies. Unfortunately, these results are affected by the high uncertainties typical of indirect measurements, which depend on the complicated modeling of the interaction of the primary particle with the atmosphere. A space experiment dedicated to measurements in this energy region has to achieve a balance between the requirements of lightness and compactness, with that of a large acceptance to cope with the low particle rates. CaloCube is a four-year-old R&amp, D project, approved and financed by the Istituto Nazionale di Fisica Nucleare (INFN) in 2014, aiming to optimize the design of a space-borne calorimeter. The large acceptance needed is obtained by maximizing the number of entrance windows, while thanks to its homogeneity and high segmentation this new detector achieves an excellent energy resolution and an enhanced separation power between hadrons and electrons. In order to optimize detector performances with respect to the total mass of the apparatus, comparative studies on different scintillating materials, different sizes of crystals, and different spacings among them have been performed making use of MonteCarlo simulations. In parallel to simulations studies, several prototypes instrumented with CsI(Tl) (Caesium Iodide, Tallium doped) cubic crystals have been constructed and tested with particle beams. Moreover, the last development of CaloCube, the Tracker-In-Calorimeter (TIC) project, financed by the INFN in 2018, is focused on the feasibility of including several silicon layers at different depths in the calorimeter in order to reconstruct the particle direction. In fact, an important requirement for &gamma, ray astronomy is to have a good angular resolution in order to allow precise identification of astrophysical sources in space. In respect to the traditional approach of using a tracker with passive material in front of the calorimeter, the TIC solution can save a significant amount of mass budget in a space satellite experiment, which can then be exploited to improve the acceptance and the resolution of the calorimeter. In this paper, the status of the project and perspectives for future developments are presented.

The CALorimetric Electron Telescope (CALET) is an astroparticle physics experiment installed on the International Space Station since August 2015. The CALET mission was conceived to address several outstanding questions of high-energy astroparticle physics, like indirect detection of dark matter, the origin of cosmic rays (CRs), their mechanisms of acceleration and galactic propagation, the presence of possible nearby astrophysical CR sources. That can be achieved by precise measurements of the fluxes of CR electrons and γ rays up to the unexplored region above 1 TeV, and the energy spectra and composition of CR nuclei from a few tens of GeV to hundreds of TeV. In order to perform these observations, the instrument combines a thick total absorption PWO crystal calorimeter for energy measurement, a scintillator hodoscope for charge identification and thin imaging tungsten-scintillating fiber calorimeter providing accurate particle tracking and complementary charge measurement. In this paper, we will present an overview of the main CALET results based on the data collected in the first three years of the mission.

International audience; An array of Single Photon Avalanche Diodes (SPAD), fabricated in a 180 nm CMOS technology featuring a high voltage (HV) option, has been investigated in terms of radiation tolerance, in view of the design of low material budget dual-tier detectors for charged particle tracking based on the coincidence of signals coming from pairs of vertically aligned pixels. Each pixel in the array includes both the processing electronics and the sensing element in a monolithic structure. The test vehicles were irradiated with 10 keV X-rays up to a dose of 1 Mrad (SiO 2 ) and with neutrons up to a fluence of 10 11 n eq cm −2 . A selection of the characterization results are presented together with the main features of a new large scale SPAD array to be fabricated in a 150 nm CMOS technology and ready for vertical interconnection in a dual layer structure.

著者人数: 91名(所属. 宇宙航空研究開発機構宇宙科学研究所(JAXA)(ISAS): 海老沢, 研; 福家, 英之; 森, 国城; 西村, 純; 高柳, 昌弘; 冨田, 洋; 上野, 史郎), Number of authors: 91(Affiliation. Institute of Space and Atronautical Science, Japan Aerospace Exploration Agency (JAXA)(ISAS): Ebisawa, Ken; Fuke, Hideyuki; Mori, Kunishiro; Nishimura, Jun; Takayanagi, Masahiro; Tomida, Hiroshi; Ueno, Shiro), Accepted: 2018-07-03, 資料番号: SA1180102000

著者人数: 93名(所属. 宇宙航空研究開発機構宇宙科学研究所(JAXA)(ISAS): 海老沢, 研; 福家, 英之; 森, 国城; 西村, 純; 高柳, 昌弘; 冨田, 洋; 上野, 史郎), Number of authors: 93(Affiliation. Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency (JAXA)(ISAS): Ebisawa, Ken; Fuke, Hideyuki; Mori, Kunishiro; Nishimura, Jun; Takayanagi, Masahiro; Tomida, Hiroshi; Ueno, Shiro), Accepted: 2018-07-26, 資料番号: SA1180103000

The direct observation of high-energy cosmic rays, up to the PeV region, will depend on highly performing calorimeters, and the physics performance will be primarily determined by their acceptance and energy resolution.Thus, it is fundamental to optimize their geometrical design, granularity, and absorption depth, with respect to the total mass of the apparatus, probably the most important constraints for a space mission. Furthermore, a calorimeter based space experiment can provide not only flux measurements but also energy spectra and particle identification to overcome some of the limitations of ground-based experiments. Calocube is a homogeneous calorimeter whose basic geometry is cubic and isotropic, so as to detect particles arriving from every direction in space, thus maximizing the acceptance; granularity is obtained by filling the cubic volume with small cubic scintillating crystals. A prototype, instrumented with CsI(Tl) cubic crystals, has been constructed and tested with particle beams.

著者人数: 91名（所属. 宇宙航空研究開発機構宇宙科学研究所(JAXA)(ISAS): 海老沢, 研; 福家, 英之; 森, 國城; 西村, 純; 高柳, 昌弘; 上野, 史郎), Accepted: 2018-02-26, 資料番号: SA1170331000

In August 2015, the CALorimetric Electron Telescope (CALET), designed for long exposure observations of high energy cosmic rays, docked with the International Space Station (ISS) and began to collect data about two months later. CALET will measure the cosmic ray electron spectrum over the energy range of 1 GeV to 20 TeV with a very high resolution of 2% above 100 GeV, based on a dedicated instrument incorporating an exceptionally thick 30 radiation-length calorimeter with both total absorption and imaging units (TASC and IMC). Each TASC readout channel must be carefully calibrated in order to obtain the degree of precision necessary to achieve the high energy resolution. This report describes the specific calibration methods, focusing on the calibration of the energy deposit of each channel to obtain an ADC unit to energy conversion factor using Minimum Ionizing Particles (MIP), known as “the MIP calibration.” This calibration is done using data acquired on Single Trigger mode, which is dedicated to acquire data from non-interacting particles for the purposes of detector calibration. To fully calibrate each TASC log, it is first necessary to correct the position dependent effects so as to equalize the response along its length. In addition, because both the PWO light yield and the APD gain will vary with temperature, it is also required to correct for this temperature dependence. Following these corrections for the position and temperature dependence, and also using events extracted using event selection based on likelihood analysis, it was possible to find the energy conversion factor. With the excellent agreement between the conversion factors obtained from proton and helium MIP data, the validity of the absolute calibration of the energy conversion factor was confirmed. In the end, this report describes the analysis of the long term stability of the MIP calibration, from which it was concluded that the time dependence of the MIP peak value was successfully removed.

The direct observation of high-energy cosmic rays, up to the PeV region, will increasingly rely on highly performing calorimeters, and the physics performance will be primarily determined by their geometrical acceptance and energy resolution. Thus, it is extremely important to optimize their geometrical design, granularity, and absorption depth, with respect to the total mass of the apparatus, which is among the most important constraints for a space mission. Calocube is a homogeneous calorimeter whose basic geometry is cubic and isotropic, so as to detect particles arriving from every direction in space, thus maximizing the acceptance; granularity is obtained by filling the cubic volume with small cubic scintillating crystals. This design forms the basis of a three-year R & D activity which has been approved and financed by INFN. A comparative study of different scintillating materials has been performed. Optimal values for the size of the crystals and spacing among them have been studied. Different geometries, besides the cubic one, and the possibility to implement dual-readout techniques have been investigated. A prototype, instrumented with CsI(Tl) cubic crystals, has been constructed and tested with particle beams. An overview of the obtained results will be presented and the perspectives for future space experiments will be discussed.

The direct detection of high-energy cosmic rays up to the PeV region is one of the major challenges for the next generation of space-borne cosmic-ray detectors. The physics performance will be primarily determined by their geometrical acceptance and energy resolution. CaloCube is a homogeneous calorimeter whose geometry allows an almost isotropic response, so as to detect particles arriving from every direction in space, thus maximizing the acceptance. A comparative study of different scintillating materials and mechanical structures has been performed by means of Monte Carlo simulation. The scintillation-Cherenkov dual read-out technique has been also considered and its benefit evaluated.

International audience; In this paper, we present a two-layered silicon sensor working in Geiger-mode avalanche regime and designed for charged particle detection. Each position-sensitive element is comprised of two vertically aligned pixels, exploiting the coincidence between two simultaneous avalanche events to discriminate between particle triggers and dark counts. This approach potentially offers several advantages. First, a low material budget can be achieved thanks to the thinning of the detector down to a few tens of microns (e.g. 50 μm) as the avalanche starts in a shallow region just a few microns deep. Operation in a regime of quenched avalanche allows for an excellent timing resolution and provides an internal gain that makes a front-end amplification stage unnecessary, thus dramatically reducing the power consumption. Fine detector segmentation is possible as the (horizontal) inter-pixel cross-talk in the detection plane can be reduced to a comfortable level while the vertical cross-talk is totally eliminated using a metal light-shield layer. The detector is also insensitive to background light. A number of applications could benefit from a detector with these characteristics, including particle tracking and vertex reconstruction in particle physics experiments at accelerators and in space, as well as ionizing radiation imaging in nuclear medicine and life-sciences.

Experimental results obtained with a prototype of a Focused Internal Reflection Cherenkov, equipped with 16 high-granularity arrays of NUV-SiPM and tested at CERN SPS in March 2015, are discussed. The detector was exposed to relativistic ions of 13, 19 and 30 GeV/amu obtained from fragmentation of a primary Ar beam. The FDIRC included a single Fused Silica radiator bar optically connected to a cylindrical mirror and an imaging focal plane of dimensions ∼4 cm×∼3 cm, covered with a total of 1024 SiPM photosensors. It was operated in photon counting mode thanks to the excellent performance of the SiPM arrays. The complete simulation of the detector was extended to the case of a planar device with multiple bars covering a sensitive area of the order of 1 m 2 . MC simulation is performed to evaluate its expected mass resolution for the identification of cosmic isotopes of astrophysical interest as 9 Be and 10 Be at energies of several GeV/amu with the goal to extend the energy reach of the present available data.

CaloCube is an R&D project borne to develop a novel calorimeter design, optimized for high-energy cosmic ray measurements in space. A small prototype made of CsI(Tl) elements has been built and tested on particle beams. A final version, made of 5×5×18 crystals and with dual readout (two photodiodes for each crystal), to cover the full required dynamic range, is under construction and will be tested at CERN SPS in Summer 2016. The dual readout compensation technique were developed and the feasibility to extract ÄŒ erenkov signals from CsI crystals verified.

The direct measurement of the cosmic-ray spectrum, up to the knee region, is one of the instrumental challenges for next generation space experiments. The main issue for these measurements is a steeply falling spectrum with increasing energy, so the physics performance of the space calorimeters are primarily determined by their geometrical acceptance and energy resolution. CaloCube is a three-year R&D; project, approved and financed by INFN in 2014, aiming to optimize the design of a space-born calorimeter. The peculiarity of the design of CaloCube is its capability of detecting particles coming from any direction, and not only those on its upper surface. To ensure that the quality of the measurement does not depend on the arrival direction of the particles, the calorimeter will be designed as homogeneous and isotropic as possible. In addition, to achieve a high discrimination power for hadrons and nuclei with respect to electrons, the sensitive elements of the calorimeter need to have a fine 3-D sampling capability. In order to optimize the detector performances with respect to the total mass of the apparatus, which is the most important constraint for a space launch, a comparative study of different scintillating materials has been performed using detailed Monte Carlo simulation based on the FLUKA package. In parallel to simulation studies, a prototype consisting in 14 layers of 3 x 3 CsI(Tl) crystals per layer has been assembled and tested with particle beams. An overview of the obtained results during the first two years of the project will be presented and the future of the detector will be discussed too.

The CALorimetric Electron Telescope (CALET) space experiment, currently under development by Japan in collaboration with Italy and the United States, will measure the flux of cosmic-ray electrons (including positrons) to 20 TeV, gamma rays to 10 TeV and nuclei with Z=1 to 40 up to 1,000 TeV during a two-year mission on the International Space Station (ISS), extendable to five years. These measurements are essential to search for dark matter signatures, investigate the mechanism of cosmic-ray acceleration and propagation in the Galaxy and discover possible astrophysical sources of high-energy electrons nearby the Earth. The instrument consists of two layers of segmented plastic scintillators for the cosmic-ray charge identification (CHD), a 3 radiation length thick tungsten-scintillating fiber imaging calorimeter (IMC) and a 27 radiation length thick lead-tungstate calorimeter (TASC). CALET has sufficient depth, imaging capabilities and excellent energy resolution to allow for a clear separation between hadrons and electrons and between charged particles and gamma rays. The instrument will be launched to the ISS within 2014 Japanese Fiscal Year (by the end of March 2015) and installed on the Japanese Experiment Module-Exposed Facility (JEM-EF). In this paper, we will review the status and main science goals of the mission and describe the instrument configuration and performance.

Future research in High Energy Cosmic Ray Physics concerns fundamental questions on their origin, acceleration mechanism, and composition. Unambiguous measurements of the energy spectra and of the composition of cosmic rays at the “knee” region could provide some of the answers to the above questions. Only ground based observations, which rely on sophisticated models describing high energy interactions in the earth׳s atmosphere, have been possible so far due to the extremely low particle rates at these energies. A calorimeter based space experiment can provide not only flux measurements but also energy spectra and particle identification, especially when coupled to a dE/dx measuring detector, and thus overcome some of the limitations plaguing ground based experiments. For this to be possible very large acceptances are needed if enough statistic is to be collected in a reasonable time. This contrasts with the lightness and compactness requirements for space based experiments. A novel idea in calorimetry is discussed here which addresses these issues while limiting the mass and volume of the detector. In fact a small prototype is currently being built and tested with ions. In this paper the results obtained will be presented in light of the simulations performed.

Measurements of the relative abundance of cosmic isotopes and of the energy dependence of their fluxes may clarify our present understanding on the confinement time of charged cosmic rays in the Galaxy. Experimental studies of these propagation clocks have been carried out by balloon and space missions at energies of a few 100 MeV/amu by means of detection techniques based on multiple d E /d x sampling, coupled with a measurement of the energy released in a thick absorber. At larger energies, the isotopic separation of light nuclei (as, for instance, 9 Be/ 10 Be) can be achieved by combining a precise measurement of the particle’s rigidity with an high resolution determination of its velocity, via the observation of the Cherenkov effect in a radiator. In this paper, we propose the introduction – for the first time in a space experiment – of the DIRC technique (Detection of Internal Reflected Cherenkov light) for the identification of cosmic-ray isotopes. This type of detector has been successfully used in electron–positron colliders for particle identification and in particular for π –K separation. While for particles with unit charge the light yield is a limiting factor, in the case of a nucleus of charge Z the larger photostatistics (due to the Z 2 dependence of Cherenkov light emission) is the key to reach an adequate angular resolution to provide a mass discrimination for isotopes of astrophysical interest. We report on the early development phase of a DIRC prototype with a focussing scheme (FDIRC) to collect the Cherenkov light onto a detector plane instrumented with a Silicon PhotoMultiplier (SiPM) array.

Silicon Photomultipliers (SiPM), known also as Multi Pixel Photon Counters (MPPC) are very promising solid-state photodetectors, working in the Geiger regime, with single photoelectron sensitivity. Low-light-level detection was investigated with a 3 mm × 3 mm MPPC by Hamamatsu, optically coupled with scintillators and Cherenkov acrylic radiators. Its performances were studied with a β-source, under different operating conditions. During the tests, the MPPC gain was stabilized using a temperature dependent feed-back loop on the operating voltage. The results of the tests are discussed.

During its second Antarctic flight, the CREAM (Cosmic Ray Energetics And Mass) balloon experiment collected data for 28 days, measuring the charge and the energy of cosmic rays (CR) with a redundant system of particle identification and an imaging thin ionization calorimeter. Preliminary direct measurements of the absolute intensities of individual CR nuclei are reported in the elemental range from carbon to iron at very high energy., Comment: 4 pages, 3 figures, presented at XV International Symposium on Very High Energy Cosmic Ray Interactions (ISVHECRI 2008)

We present new measurements of the energy spectra of cosmic-ray (CR) nuclei from the second flight of the balloon-borne experiment Cosmic Ray Energetics And Mass (CREAM). The instrument included different particle detectors to provide redundant charge identification and measure the energy of CRs up to several hundred TeV. The measured individual energy spectra of C, O, Ne, Mg, Si, and Fe are presented up to $\sim 10^{14}$ eV. The spectral shape looks nearly the same for these primary elements and it can be fitted to an $E^{-2.66 \pm 0.04}$ power law in energy. Moreover, a new measurement of the absolute intensity of nitrogen in the 100-800 GeV/$n$ energy range with smaller errors than previous observations, clearly indicates a hardening of the spectrum at high energy. The relative abundance of N/O at the top of the atmosphere is measured to be $0.080 \pm 0.025 $(stat.)$ \pm 0.025 $(sys.) at $\sim $800 GeV/$n$, in good agreement with a recent result from the first CREAM flight., 32 pages, 10 figures. Accepted for publication in Astrophysical Journal

Solid-state photodetectors working in the Geiger mode—known as Silicon PhotoMultipliers (SiPM) or MultiPixel Photon Counters (MPPC)—are currently being developed with increasingly large active areas. Potential applications for low-light-level detection were investigated with a 9 mm 2 MPPC, recently made available by Hamamatsu. The device was optically coupled with a scintillator and its performances, in terms of single photoelectron discrimination, were studied in a series of measurements under different operating conditions. An active control of the gain was implemented by a linear feedback on the operating voltage. The results of the tests are discussed.

We present new measurements of heavy cosmic-ray nuclei at high energies per- formed during the first flight of the balloon-borne cosmic-ray experiment CREAM (Cosmic-Ray Energetics And Mass). This instrument uses multiple charge detectors and a transition radiation detector to provide the first high accuracy measurements of the relative abundances of elements from boron to oxygen up to energies around 1 TeV/n. The data agree with previous measurements at lower energies and show a relatively steep decline (~E$^-0.6$ to E$^-0.5$) at high energies. They further show the source abundance of nitrogen relative to oxygen is ~10% in the TeV/n region., Accepted for publication in Astroparticle Physics

Launched from McMurdo (Antarctica) in December 2005, the balloon experiment CREAM (cosmic ray energetics and mass) collected about 15 million triggers during its second flight of 28 days. Redundant charge identification, by two pixelated silicon arrays and a time resolved pulse shaping technique from a scintillator system, allowed a clear signature of the primary nuclei. The energy was measured with a tungsten/SciFi calorimeter preceded by a graphite target. Preliminary results from the analysis of the data of the second flight are presented.

The balloon-borne cosmic-ray experiment CREAM (Cosmic Ray Energetics And Mass) has completed two flights in Antarctica, with a combined duration of 70 days. One of the detectors in the payload is the SCD (silicon charge detector) that measures the charge of high energy cosmic rays. The SCD was assembled with silicon sensors. A sensor is a 4 × 4 array of DC-coupled PIN diode pixels with the total active area of 21 × 16 mm2. The SCD used during the first flight (December 2004-January 2005) was a single layer device, then upgraded to a dual layer device for the second flight (December 2005-January 2006), covering the total sensitive area of 779 × 795 mm2. Flight data demonstrated that adding a second layer improved SCD performance, showing excellent particle charge resolution. With a total dissipation of 136 W for the dual layer system, special care was needed in designing thermal paths to keep the detector temperature within its operational range. As a consequence, flight temperatures of the SCD, even at diurnal maximum were kept below 38°C. The SCD mechanical structure was designed to minimize the possibility of damage to the sensors and electronics from the impacts of parachute deployment and landing. The detector was recovered successfully following the flight and is being refurbished for the next flight in 2007. Details of construction, operation, and performance are presented for the dual-layered SCD flown for the second CREAM flight.

The CALorimetric Electron Telescope (CALET) is a space experiment, currently under development by Japan in collaboration with Italy and the United States, which will measure the flux of cosmic-ray electrons (and positrons) up to 20 TeV energy, of gamma rays up to 10 TeV, of nuclei with Z from 1 to 40 up to 1 PeV energy, and will detect gamma-ray bursts in the 7 keV to 20 MeV energy range during a 5 year mission. These measurements are essential to investigate possible nearby astrophysical sources of high energy electrons, study the details of galactic particle propagation and search for dark matter signatures. The main detector of CALET, the Calorimeter, consists of a module to identify the particle charge, followed by a thin imaging calorimeter (3 radiation lengths) with tungsten plates interleaving scintillating fibre planes, and a thick energy measuring calorimeter (27 radiation lengths) composed of lead tungstate logs. The Calorimeter has the depth, imaging capabilities and energy resolution necessary for excellent separation between hadrons, electrons and gamma rays. The instrument is currently being prepared for launch (expected in 2015) to the International Space Station ISS, for installation on the Japanese Experiment Module - Exposure Facility (JEM-EF).

The development of the GAMMA-400 ?-ray telescope continues. The GAMMA-400 is designed to measure fluxes of ?-rays and the electron-positron cosmic-ray component possibly associated with annihilation or decay of dark matter particles; and to search for and study in detail discrete ?-ray sources, to measure the energy spectra of Galactic and extragalactic diffuse ?-rays, and to study ?-ray bursts and ?-rays from the active Sun. The energy range for measuring ?-rays and electrons (positrons) is from 100 MeV to 3000 GeV. For 100-GeV ?-rays, the ?-ray telescope has an angular resolution of ~0.01°, an energy resolution of ~1%, and a proton rejection factor of ~5 × 105. The GAMMA-400 will be installed onboard the Russian Space Observatory.

GAMMA-400 γ-ray telescope is designed to measure fluxes of γ-rays and the electron–positron cosmic ray component possibly generated in annihilation or decay of dark matter particles; to search for and study in detail discrete γ-ray sources, to examine the energy spectra of Galactic and extragalactic diffuse γ-rays, to study γ-ray bursts and γ-rays from the active Sun. GAMMA-400 consists of plastic scintillation anticoincidence top and lateral detectors, converter-tracker, plastic scintillation detectors for the time-of-flight system (TOF), two-part calorimeter (CC1 and CC2), plastic scintillation lateral detectors of calorimeter, plastic scintillation detectors of calorimeter, and neutron detector. The converter-tracker consists of 13 layers of double (x, y) silicon strip coordinate detectors (pitch of 0.08mm). The first three and final one layers are without tungsten while the middle nine layers are interleaved with nine tungsten conversion foils. The thickness of CC1 and CC2 is 2 X0 (0.1λ0) and 23 X0 (1.1λ0) respectively (where X0 is radiation length and λ0 is nuclear interaction one). The total calorimeter thickness is 25 X0 or 1.2λ0 for vertical incident particles registration and 54 X0 or 2.5λ0 for laterally incident ones.The energy range for γ-rays and electrons (positrons) registration in the main aperture is from ∼0.1GeV to ∼3.0 TeV. The γ-ray telescope main aperture angular and energy resolutions are respectively ∼0.01 and ∼1% for 102 GeV γ-quanta, the proton rejection factor is ∼5×105. The first three strip layers without tungsten provide the registration of γ-rays down to ∼20 MeV in the main aperture. Also this aperture allows investigating high energy light nuclei fluxes characteristics.Electrons, positrons, light nuclei and gamma-quanta will also register from the lateral directions due to special aperture configuration. Lateral aperture energy resolution is the same as for main aperture for electrons, positrons, light nuclei and gamma-quanta in energy range E>1.0GeV. But using lateral aperture it is possible to detect low-energy gammas in the ranges 0.2 − 10 MeV and 10 MeV – 1.0GeV with energy resolution 8% − 2% and 2% correspondingly accordingly to GAMMA-400 “Technical Project” stage results. Angular resolution in the lateral aperture provides only for low-energy gamma-quanta from non-stationary events (GRB, solar flares and so on) due segments of CC2 count rate analysis.GAMMA-400 γ-ray telescope will be installed onboard the Russian Space Observatory GAMMA-400. The lifetime of the space observatory will be at least seven years. The launch of the space observatory is scheduled for the early 2020s.

Future space experiments dedicated to the observation of high-energy gamma and cosmic rays will increasingly rely on a highly performing calorimetry apparatus, and their physics performance will be primarily determined by the geometrical dimensions and the energy resolution of the calorimeter deployed. Thus it is extremely important to optimize its geometrical acceptance, the granularity, and its absorption depth for the measurement of the particle energy with respect to the total mass of the apparatus which is the most important constraint for a space launch. The proposed design tries to satisfy these criteria while staying within a total mass budget of about 1.6 tons. Calocube is a homogeneous calorimeter instrumented with Cesium iodide (CsI) crystals, whose geometry is cubic and isotropic, so as to detect particles arriving from every direction in space, thus maximizing the acceptance, granularity is obtained by filling the cubic volume with small cubic CsI crystals. The total radiation length in any direction is more than adequate for optimal electromagnetic particle identification and energy measurement, whilst the interaction length is at least suficient to allow a precise reconstruction of hadronic showers. Optimal values for the size of the crystals and spacing among them have been studied. The design forms the basis of a three-year R&D; activity which has been approved and financed by INFN. An overall description of the system, as well as results from preliminary tests on particle beams will be described.

The GAMMA-400 gamma-ray telescope with excellent angular and energy resolutions is designed to search for signatures of dark matter in the fluxes of gamma-ray emission and electrons + positrons. Precision investigations of gamma-ray emission from Galactic Center, Crab, Vela, Cygnus, Geminga, and other regions will be performed, as well as diffuse gamma-ray emission, along with measurements of high-energy electron + positron and nuclei fluxes. Furthermore, it will study gamma-ray bursts and gamma-ray emission from the Sun during periods of solar activity. The energy range of GAMMA-400 is expected to be from ~20 MeV up to TeV energies for gamma rays, up to 20 TeV for electrons + positrons, and up to 10E15 eV for cosmic-ray nuclei. For high-energy gamma rays with energy from 10 to 100 GeV, the GAMMA-400 angular resolution improves from 0.1{\deg} to ~0.01{\deg} and energy resolution from 3% to ~1%; the proton rejection factor is ~5x10E5. GAMMA-400 will be installed onboard the Russian space observatory., Comment: 8 pages, 2 figures, 2 tables, submitted to the proceedings of ICRC2015

Particle detector prototypes equipped with Silicon Photomultipliers designed to be sensitive in the near-ultraviolet wavelength region (NUV-SiPM) were tested in a beam of rela- tivistic ions with electric charge Z in the range , at energies 13 and 30 GeV/amu at CERN SPS. Two different prototypes of charged particle detectors were tested. The first one was a scintillating fiber hodoscope with individual fibers optically coupled to single SiPM devices. The second one consisted of an array of discrete SiPM sensors that were directly exposed to the ion beam to study their capability to trigger an avalanche in response to the ionization generated inside the silicon device. In this paper, we fi rst report the results of the characterization and dedicated tests of the NUV-SiPM sensors that were carried out in our laboratory under controlled conditions; then, we discuss the analysis of the beam test data and the performance of both prototypes.

The next generation of space-based or balloon-borne experiments, dedicated to the study of high energy cosmic rays, are designed to identify the primary particle and to record electronically in flight its charge and energy. The large number of readout channels drives the front-end electronics design toward low power devices with the additional requirement of a large dynamic range. This turns out to be mandatory both for charge detectors dedicated to the identification of high-Z nuclei and for calorimeters designed to operate in the multi-TeV range. The development of new front-end electronics designed according to the above requirements will be reported.

Particle detector prototypes, equipped with Silicon PhotoMultipliers (SiPMs) and readout by dedicated front-end electronics, were tested with beams of fully ionized nuclei from boron ( Z =5) to nickel ( Z =28) with a kinetic energy ∼ 1 GeV / amu , at the Fragment Separator (FRS) of the GSI Helmholtzzentrum fur Schwerionenforschung in Darmstadt. The tested instruments included prototypes of Cherenkov and scintillation hodoscopes designed for cosmic-ray experiments in space or in the upper atmosphere. In this paper, we summarize the results from the analysis of the beam tests data and of dedicated laboratory tests to characterize the response of the photosensors, the front-end electronics and the performance of the prototypal detectors.

Calorimetry plays an essential role in experiments observing high energy gamma and cosmic rays in space. The observational capabilities are mainly limited by the geometrical dimensions and the mass of the calorimeter. Since deployable mass depends on the design of the detector and the total mass of the payload, it is important to optimize the geometrical acceptance of the calorimeter for rare events, its granularity for particle identification, and its absorption depth for the measurement of the particle energy. A design of a calorimeter that could simultaneously optimize these characteristics assuming a mass limit of about 1.6 t has been studied. As a result, a homogeneous calorimeter instrumented with cesium iodide (CsI) crystals was chosen as the best compromise given the total mass constraint. The most suitable geometry found is cubic and isotropic, so as to detect particles arriving from every direction in space, thus maximizing the acceptance; granularity is obtained by filling the cubic volume with small cubic CsI crystals. The total radiation length in any direction is very large, and allows for optimal electromagnetic particle identification and energy measurement, while the interaction length is at least sufficient to allow a precise reconstruction of hadronic showers. Optimal values for the size of the crystals and spacing among them have been studied. Two prototypes have been constructed and preliminary tests with high energy ion and muon beams are reported.

The Electromagnetic Calorimeter (ECAL) of the AMS-02 experiment is a fine grained lead-scintillating fibres sampling calorimeter that allows for a precise three-dimensional imaging of the longitudinal and lateral shower development. It provides a high (>= 10(6)) electron/hadron discrimination with the other AMS-02 detectors [1] and good energy resolution. The calorimeter also provides a standalone photon trigger capability to AMS-02. The mechanical assembly was realized to ensure minimum weight, still supporting the intrinsically heavy calorimeter during launch. ECAL light collection system and electronics are designed to measure electromagnetic particles over a wide energy range, from GeV up to TeV. A full-scale flight-like model was tested using electrons and proton beams with energies ranging from 6 to 250 GeV. (c) 2013 Elsevier B.V. All rights reserved.

A large area silicon array for the next generation of space-based experiments has been designed to determine, via multiple d E / d x measurements, the electric charge of cosmic radiation. The instrument can achieve an excellent charge discrimination, thus allowing to assess the elemental composition of charged cosmic rays at relativistic energies. Pairs of silicon sensors segmented into pixels were tested with a beam of fully ionized nuclei from boron to nickel ( Z =28) with a kinetic energy of ∼ 1 GeV / amu , at the Fragment Separator (FRS) of the GSI Helmholtzzentrum fur Schwerionenforschung in Darmstadt. The response of the sensors to different nuclear species was accurately characterized. The results of the beam test clearly show that a double-layered silicon array can achieve single-element separation with a resolution close to 0.2 electron charge units, in the whole interval of atomic number Z under test.

A new class of instruments – based on Silicon PhotoMultiplier (SiPM) photosensors – are currently under development for the next generation of Astroparticle Physics experiments in future space missions. A custom front-end ASIC (Application Specific Integrated Circuit) for the readout of 64 SiPM sensors was specified in collaboration with GM-IDEAS (Norway) that designed and manufactured the ASIC. Our group developed a custom readout board equipped with a 16 bit ADC for the digitization of both pulse height and time information. A time stamp, generated by the ASIC in correspondence of the threshold crossing time, is digitized and recorded for each channel. This allows to define a narrow time window around the physics event that reduces significantly the background due to the SiPM dark count rate. In this paper, we report on the preliminary test results obtained with the readout board prototype.

At an energy scale of 1015–1016 eV, a direct measurement of the energy carried by charged cosmic radiation is a real challenge for balloon-borne and space based instruments. As a consequence of the very small fluxes, a large collecting power is required which is difficult to accommodate with weight-limited instruments equipped with calorimeters. A different approach has been proposed that might allow for a sizeable reduction of the instrument mass. It is based on a kinematical technique, whereby the energy of the cosmic-ray is estimated on the basis of the measured angular distribution of the secondaries resulting from its interaction in a target. In this paper, we review the basic principles of the method and study the properties of different energy estimators by means of a full simulation of the interaction of the incident particle in a conceptual instrument. We also discuss the intrinsic limitations of the method and investigate its possible application to direct measurements of the cosmic-ray spectrum in the region of the ‘knee’.

The balloon-borne Cosmic Ray Energetics And Mass (CREAM) experiment launched five times from Antarctica has achieved a cumulative flight duration of about 156 days above 99.5% of the atmosphere. The instrument is configured with complementary and redundant particle detectors designed to extend direct measurements of cosmic-ray composition to the highest energies practical with balloon flights. All elements from protons to iron nuclei are separated with excellent charge resolution. Here we report results from the first two flights of ~70 days, which indicate hardening of the elemental spectra above ~200 GeV/nucleon and a spectral difference between the two most abundant species, protons and helium nuclei. These results challenge the view that cosmic-ray spectra are simple power laws below the so-called knee at ~1015 eV. This discrepant hardening may result from a relatively nearby source, or it could represent spectral concavity caused by interactions of cosmic rays with the accelerating shock. Other possible explanations should also be investigated., 21 pages, 5 figures, published in ApJL (corresponding author: seo@umd.edu)