Search

In this paper, we report a comparative study of fiber optic sensors for applications of relative humidity (RH) monitoring in high-radiation environments. In particular, we present investigations carried out since 2011 by our multidisciplinary research group, in collaboration with the European Organization for Nuclear Research (CERN) in Geneva. Our research has been first focused on the development of polyimide-coated fiber Bragg grating (FBG) sensors, and recently, it has been extended to nanoscale metal oxide-coated long-period gratings (LPGs). Experimental tests in the [0-70] %RH range at different temperatures, before and after γ-ionizing radiation exposures, have been carried out to assess the sensors' performances in conditions required in experiments running at CERN. The advantages and disadvantages of the two proposed technologies are discussed in this paper in light of their possible application in high-energy physics environments. In particular, reported results suggest that LPG-based sensors can be preferred in some applications (particularly in presence of very low humidity levels) mainly because they are able to provide very high RH sensitivity (up to 1.4 nm/% RH), which is up to three orders of magnitude higher than that exhibited by FBG-based hygrometers. On the other side, compared with FBGs, LPGs are more difficult to multiplex due to limitations in terms of available bandwidth.

The design, fabrication, and tests of the new generation of superconducting magnets for the High Luminosity upgrade of the Large Hadron Collider (HL-LHC) require the support of an adequate sensing technology able to assure the integrity of the strain-sensitive and brittle superconducting cables through the whole service life of the magnet: assembly up to 150 MPa, cool down to 1.9 K, and powering up to about 16 kA. A precise temperature monitoring is also needed, in order to guarantee the safe working condition of the superconducting cables in the power transmission lines (SC-Link) designed to feed the magnet over long distance. Fiber Bragg Grating-based temperature and strain monitoring systems have been implemented in the first SC-Link prototype and in two subscale dipole magnets and tested in the cryogenic test facility at CERN, at 30 K, 77 K, and 1.9 K.

The recently installed internal gas target at LHCb presents exceptional opportunities for an extensive physics program for heavy-ion, hadron, spin, and astroparticle physics. A storage cell placed in the LHC primary vacuum, an advanced Gas Feed System, the availability of multi-TeV proton and ion beams, and the recent upgrade of the LHCb detector make this project unique worldwide. In this paper, we outline the main components of the system, the physics prospects it offers, and the hardware challenges encountered during its implementation. The commissioning phase has yielded promising results, demonstrating that fixed-target collisions can occur concurrently with the collider mode without compromising efficient data acquisition and high-quality reconstruction of beam-gas and beam-beam interactions.

The end of the twentieth century was witness to the merger of several technological disciplines that could eventually revolutionize engineering design philosophy and lead to the creation of intelligence within otherwise inanimate structures. This new technology will endow a structure with senses and the ability to react to its environment and change its state, shape and geometry. The key point for the practical realization of the so-called smart materials is the availability of robust and reliable structurally integrated sensors able to monitor the state of the structure. To this aim, a fiber optic multiparameter sensing system for process and structural health monitoring in concrete structures is presented. The reflectometric technique has been implemented for refractive-index measurements by using as transducer the fiber end/host interface. Results on the capability of the developed sensor to monitor the curing process of thermoset-based composites are presented. The integration with fiber Bragg gratings (FBGs) with the aim to perform temperature and strain measurements has been discussed. Two low-cost intensity-based demodulation techniques for FBGs interrogation have been developed and tested. [ABSTRACT FROM PUBLISHER]

The beam-gas vertex (BGV) detector is an innovative instrument measuring noninvasively the transverse beam size in the Large Hadron Collider (LHC) using reconstructed tracks from beam-gas interactions. The BGV detector was installed in 2016 as part of the R&D for the High-Luminosity LHC project. It allows beam size measurements throughout the LHC acceleration cycle with high-intensity physics beams. A precision better than 2% with an integration time of less than 30 s is obtained on the average beam size measured, while the transverse size of individual proton bunches is measured with a resolution of 5% within 5 min. Particles emerging from beam-gas interactions in a specially developed gas volume along the beam direction are recorded by two tracking stations made of scintillating fibers. A scintillator trigger system selects, on-line, events with tracks originating from the interaction region. All the detector elements are located outside the beam vacuum pipe to simplify the design and minimize interference with the accelerated particle beam. The beam size measurement results presented here are based on the correlation between tracks originating from the same beam-gas interaction vertex.

Myocardial Infarction (MI), commonly known as heart attack, is a cardiac condition characterized by damage to a portion of the heart, specifically the myocardium, due to the disruption of blood flow. Given its recurring and often asymptomatic nature, there is the need for continuous monitoring using wearable devices. This paper proposes a single-microcontroller-based system designed for the automatic detection of MI based on the Edge Computing paradigm. Two solutions for MI detection are evaluated, based on Machine Learning (ML) and Deep Learning (DL) techniques. The developed algorithms are based on two different approaches currently available in the literature, and they are optimized for deployment on low-resource hardware. A feasibility assessment of their implementation on a single 32-bit microcontroller with an ARM Cortex-M4 core was examined, and a comparison in terms of accuracy, inference time, and memory usage was detailed. For ML techniques, significant data processing for feature extraction, coupled with a simpler Neural Network (NN) is involved. On the other hand, the second method, based on DL, employs a Spectrogram Analysis for feature extraction and a Convolutional Neural Network (CNN) with a longer inference time and higher memory utilization. Both methods employ the same low power hardware reaching an accuracy of 89.40% and 94.76%, respectively. The final prototype is an energy-efficient system capable of real-time detection of MI without the need to connect to remote servers or the cloud. All processing is performed at the edge, enabling NN inference on the same microcontroller.

In order to complete this set of three companion papers, in this last, we focus our attention on environmental monitoring by taking advantage of photonic technologies. After reporting on some configurations useful for high precision agriculture, we explore the problems connected with soil water content measurement and landslide early warning. Then, we concentrate on a new generation of seismic sensors useful in both terrestrial and under water contests. Finally, we discuss a number of optical fiber sensors for use in radiation environments.

Our group, involving researchers from different universities in Campania, Italy, has been working for the last twenty years in the field of photonic sensors for safety and security in healthcare, industrial and environment applications. This is the first in a series of three companion papers. In this paper, we introduce the main concepts of the technologies employed for the realization of our photonic sensors. Then, we review our main results concerning the innovative applications for infrastructural and transportation monitoring.

The employability of photonics technology in the modern era's highly demanding and sophisticated domain of aerospace and submarines has been an appealing challenge for the scientific communities. In this paper, we review our main results achieved so far on the use of optical fiber sensors for safety and security in innovative aerospace and submarine applications. In particular, recent results of in-field applications of optical fiber sensors in aircraft monitoring, from a weight and balance analysis to vehicle Structural Health Monitoring (SHM) and Landing Gear (LG) monitoring, are presented and discussed. Moreover, underwater fiber-optic hydrophones are presented from the design to marine application.

Pulse waves (PWs) are mechanical waves that propagate from the ventricles through the whole vascular system as brisk enlargements of the blood vessels' lumens, caused by sudden increases in local blood pressure. Photoplethysmography (PPG) is one of the most widespread techniques employed for PW sensing due to its ability to measure blood oxygen saturation. Other sensors and techniques have been proposed to record PWs, and include applanation tonometers, piezoelectric sensors, force sensors of different kinds, and accelerometers. The performances of these sensors have been analyzed individually, and their results have been found not to be in good agreement (e.g., in terms of PW morphology and the physiological parameters extracted). Such a comparison has led to a deeper comprehension of their strengths and weaknesses, and ultimately, to the consideration that a multimodal approach accomplished via sensor fusion would lead to a more robust, reliable, and potentially more informative methodology for PW monitoring. However, apart from various multichannel and multi-site systems proposed in the literature, no true multimodal sensors for PW recording have been proposed yet that acquire PW signals simultaneously from the same measurement site. In this study, a true multimodal PW sensor is presented, which was obtained by integrating a piezoelectric forcecardiography (FCG) sensor and a PPG sensor, thus enabling simultaneous mechanical-optical measurements of PWs from the same site on the body. The novel sensor performance was assessed by measuring the finger PWs of five healthy subjects at rest. The preliminary results of this study showed, for the first time, that a delay exists between the PWs recorded simultaneously by the PPG and FCG sensors. Despite such a delay, the pulse waveforms acquired by the PPG and FCG sensors, along with their first and second derivatives, had very high normalized cross-correlation indices in excess of 0.98. Six well-established morphological parameters of the PWs were compared via linear regression, correlation, and Bland-Altman analyses, which showed that some of these parameters were not in good agreement for all subjects. The preliminary results of this proof-of-concept study must be confirmed in a much larger cohort of subjects. Further investigation is also necessary to shed light on the physical origin of the observed delay between optical and mechanical PW signals. This research paves the way for the development of true multimodal, wearable, integrated sensors and for potential sensor fusion approaches to improve the performance of PW monitoring at various body sites.

In the proposed work, a fiber-optic-based sensor network was employed for the monitoring of the liquid resin infusion process. The item under test was a panel composed by a skin and four stringers, sensorized in such a way that both the temperature and the resin arrival could be monitored. The network was arranged with 18 Fiber Bragg Gratings (FBGs) working as temperature sensors and 22 fiber optic probes with a modified front-end in order to detect the resin presence. After an in-depth study to find a better solution to install the sensors without affecting the measurements, the system was investigated using a commercial Micron Optics at 0.5 Hz, with a passive split-box connected in order to be able to sense all the sensors simultaneously. The obtained results in terms of resin arrival detection at different locations and the relative temperature trend allowed us to validate an infusion process numerical model, giving us better understanding of what the actual resin flow was and the time needed to dry preform filling during the infusion process.

In this manuscript, an optically passive fiber Bragg grating (FBG) interrogation system able to perform high-frequency measurement is proposed. The idea is mainly based on the use of an arrayed waveguide grating (AWG) device which is used to discriminate the fiber optic sensor (FOS) wavelength encoded response under test in function of its output channels. As made clear by the theoretical model studied in the proposed manuscript, the Bragg wavelength shift can be detected as in linear dependence with the proposed interrogation function which changes with the voltage produced by two (or more) adjacent AWG output channels. To prove the feasibility of the system, some experimental analyses are conducted with a custom electrical module characterized by high-speed and low-noise operational amplifiers. As static measurements, three FBGs with different full width at half maximum (FWHM) have been monitored under wide-range wavelength variation; while, as dynamic measurement, one FBG, glued onto a metal plate, in order to sense the vibration at low and high frequency, was detected. The output signals have been processed by a digital acquisition (DAQ) board and a graphical user interface (GUI). The presented work highlights the characteristics of the proposed idea as competitor among the entire class of interrogation systems currently used. This is because here, the main device, that is the AWG, is passive and reliable, without the need to use modulation signals, or moving parts, that affect the speed of the system. In addition, the innovative multi-channel detection algorithm allows the use of any type of FOS without the need to have a perfectly match of spectra. Moreover, it is also characterized by a high dynamic range without loss of sensitivity.

Background: Keyhole surgery is characterized by loss of dexterity of surgeon's movements because of the limited workspace, nonintuitive motor skills of the surgical systems, and loss of tactile sensation that may lead to tissue damage and bad execution of the tasks., Methods: In this paper, a three-fingered underactuated miniature tool for robot-aided laparoscopic surgery is presented. The design is conceived to realize a closed-hand configuration allowing the insertion of the tool into the abdominal cavity through the trocar in one step and to reach different grasping as well as pushing/holding configurations once in the cavity., Results: Aiming to replicate human hand dexterity and versatility, different solutions for the kinematic structure of the hand are analyzed using quality indices to evaluate the manipulability and stability of the grasp. Furthermore, a first prototype of fingertip force sensor based on fiber Bragg grating (FBG) technology has been realized and tested. The design choices of the prototype are described and discussed with the aid of experiments., Conclusions: The whole concept and the need for such anthropomorphic tool are discussed with surgeons to highlight constraints and potentials in surgical tasks. The feedback by expert surgeons is used to provide specifications and improvements to the kinematics and mechanical design. The investigations of different designs allow identifying the optimal solution to improve grasping and manipulation capabilities. The tests on FBG sensors led to the conclusion that this technology guarantees good performance and can be a good solution for applications in surgical robotics., (© 2018 John Wiley & Sons, Ltd.)

In this work, we report on a novel approach for measuring the dose absorbed by the EBT3 Gafchromic™ films exposed to 1 MeV electron beam and 250 kV X-rays in the range 0.5-100 Gy. Although EBT3 is specifically designed to obtain best performance for applications where the maximum dose is less than 10 Gy, there are certain clinical applications requiring dose ranges well above this value. In order to cover wider dose ranges, further models characterized by a thinner sensitive layer and/or different chemical composition have been released. Another method exploiting the three-channel flatbed scanner to delay the saturation point of EBT3 has been also reported. The technique proposed here, aimed at extending the sensitivity of the EBT3 film to high doses up to 100 Gy while ensuring a low dose uncertainty, is based on a broadband analysis of the absorption spectrum of the film in response to irradiation. By combining a wavelength-based approach with the monitoring of two characteristic peaks of the EBT3 absorption spectrum, we demonstrated the capability of measuring the dose in the range 0.5-100 Gy with an experimental uncertainty below 4% for doses lower than 5.52 Gy and below 2% for higher dose levels. Finally, through a dynamic fitting procedure integrating the two aforesaid approaches, a total uncertainty lower than 4%, including both the experimental and fitting errors, was achieved in the whole range 0.5-100 Gy. These results are promising in view of a potential application of this technique in the field of clinical dosimetry at high dose levels., (Copyright © 2019. Published by Elsevier Ltd.)

Radiochromic film dosimetry has been widely employed in most of the applications of radiation physics for over twenty years. This is due to a number of appealing features of radiochromic films, such as reliability, accuracy, ease of use and cost. However, current radiochromic film reading techniques, based on the use of commercial densitometers and scanners, provide values of dose only after the exposure of the films to radiation. In this work, an innovative methodology for the real-time reading of radiochromic films is proposed for some specific applications. The new methodology is based on opto-electronic instrumentation that makes use of an optical fiber probe for the determination of optical changes of the films induced by radiation and allows measurements of dose with high degree of precision and accuracy. Furthermore, it has been demonstrated that the dynamic range of some kinds of films, such as the EBT3 Gafchromic films (intensively used in medical physics), can be extended by more than one order of magnitude. Owing to the numerous advantages with respect to the commonly used reading techniques, a National Patent was filed in January 2018.

In this work, we report on the first demonstration of Lab on Fiber (LOF) dosimeter for ionizing radiation monitoring at ultra-high doses. The new dosimeter consists in a metallo-dielectric resonator at sub-wavelength scale supporting localized surface plasmon resonances realized on the optical fiber (OF) tip. The resonating structure involves two gold gratings separated by a templated dielectric layer of poly(methyl methacrylate) (PMMA). Two LOF prototypes have been manufactured and exposed at the IRRAD Proton Facility at CERN in Geneva to 23 GeV protons for a total fluence of 0.67 × 10 16 protons/cm 2 , corresponding to an absorbed dose of 1.8 MGy. Experimental data demonstrated the "radiation resistance" feature of the LOF devices and a clear dependence of the reflected spectrum versus the total dose, expressed by a cumulative blue-shift of ~1.4 nm of the resonance combined with a slight increase of 0.16 dBm in the reflected spectrum. The numerical analysis carried out to correlate the experimental results with the dimensional and physical properties of the resonator, expected to be tightly connected to the absorbed dose, suggests that the main phenomenon induced by exposure to proton beam and able to explain the measured spectral behavior is the reduction of the PMMA thickness, which is also consistent with past literature in the field. Preliminary results demonstrated the potentiality of the proposed platform as dosimeter at MGy dose levels for high energy physics experiments.

This Letter deals with a feasibility analysis for the development of radiation-tolerant fiber-optic humidity sensors based on long-period grating (LPG) technology to be applied in high-energy physics (HEP) experiments currently running at the European Organization for Nuclear Research (CERN). In particular, here we propose a high-sensitivity LPG sensor coated with a finely tuned titanium dioxide (TiO₂) thin layer (~100 nm thick) through the solgel deposition method. Relative humidity (RH) monitoring in the range 0%-75% and at four different temperatures (in the range -10°C-25°C) was carried out to assess sensor performance in real operative conditions required in typical experiments running at CERN. Experimental results demonstrate the very high RH sensitivities of the proposed device (up to 1.4 nm/% RH in correspondence to very low humidity levels), which turned out to be from one to three orders of magnitude higher than those exhibited by fiber Bragg grating sensors coated with micrometer-thin polyimide overlays. The radiation tolerance capability of the TiO₂-coated LPG sensor is also investigated by comparing the sensing performance before and after its exposure to a 1 Mrad dose of γ-ionizing radiation. Overall, the results collected demonstrate the strong potential of the proposed technology with regard to its future exploitation in HEP applications as a robust and valid alternative to the commercial (polymer-based) hygrometers currently used.

In this paper we describe a novel temperature mapping system based on a standard infrared camera with 50 Hz frame rate for the measurement of ultrafast temperature transients which, in principle, demand for a much faster acquisition rate. In particular, we base our system on the widely used equivalent time sampling concept which can be adapted to the temperature acquisition system, thanks to a very fast and sensitive camera sensor: an InSb sensor, which allows a reduced integration time of 10 micros, and a custom digital synchronization circuit. The latter has been realized by the usage of a fully programmable digital circuit, which generates all the signals needed for the synchronization of the IR camera, of the experiment, and a personal computer needed for data acquisition and storage. We show, with experiments, how this system is capable of detecting temperature transients with an equivalent bandwidth of 100 kHz full frame, far beyond the capabilities of the fastest available IR cameras.

In this paper we present a novel approach to temperature sensing with optoelectronic devices which relies on the usage of bare silicon as the transducing material. The device is composed by a single mode input waveguide, a MMI region where a number of higher order modes is also allowed to propagate and two output waveguides. The refractive index variation in the MMI section due to temperature shifts induces different phase velocities of the various propagating modes. The position of the input and output waveguides together with the length and width of the MMI section are chosen in order to maximize the sensitivity of the device. Analytical calculations are presented together with BPM simulations aimed to the maximization of the sensitivity of the sensor as a function of its geometries.

We describe a novel noninvasive optical technique to monitor the refractive-index variation in an epoxy-based resin that is due to the polymerization process. This kind of resin is widely used in polymer matrix composites. It is well known that the process of fabricating a thermoset-based composite involves mass and heat transfer coupled with irreversible chemical reactions that induce physical changes. To improve the quality and the reliability of these materials, monitoring the cure and optimization of the manufacturing process are of key importance. We discuss the basic operating principles of an optical system based on angle deflection measurements and present typical cure-monitoring results obtained from optical characterization. The method provides a flexible, high-sensitivity, material-independent, low-cost, noninvasive tool for monitoring real-time refractive-index variation.