Search

Catalyst passivation through carbon poisoning is a common and costly problem as it reduces the lifetime and performance of the catalyst. Adding oxygen to the feed stream could reduce poisoning but may also affect the activity negatively. We have studied the dehydrogenation, decomposition, and desorption of naphthalene co-adsorbed with oxygen on Ni(111) by combining temperature-programmed desorption (TPD), sum frequency generation spectroscopy (SFG), photoelectron spectroscopy (PES), and density functional theory (DFT). Chemisorbed oxygen reduces the sticking of naphthalene and shifts H2 production and desorption to higher temperatures by blocking active Ni sites. Oxygen increases the production of CO and reduces carbon residues on the surface. Chemisorbed oxygen is readily removed when naphthalene is decomposed. Oxide passivates the surface and reduces the sticking coefficient. But it also increases the production of CO dramatically and reduces the carbon residues. Ni2O3 is more active than NiO., QC 20240322

There are several difficulties when experimentally determined reaction mechanisms are applied from model systems to real catalysis. Besides the infamous pressure and material gaps, it is sometimes necessary to consider impurities in the real reactant feedstock that can act as promoters or catalyst poisons and alter the reaction path. In this study, the effect of sulfur on the dehydrogenation of naphthalene on Ni(111) is investigated by using X-ray photoelectron spectroscopy and scanning tunneling microscopy. Sulfur induces a (5√3 × 2) surface reconstruction, as previously reported in the literature. The sulfur does not have a strong effect on the dehydrogenation temperature of naphthalene. However, the presence of sulfur leads to a preferred formation of carbidic over graphitic carbon and a strong inhibition of carbon diffusion into the nickel bulk, which is one of the steps of destructive whisker carbon formation described in the catalysis literature.

There are several difficulties when experimentally determined reaction mechanisms are applied from model systems to real catalysis. Besides the infamous pressure and material gaps, it is sometimes necessary to consider impurities in the real reactant feedstock that can act as promoters or catalyst poisons and alter the reaction path. In this study, the effect of sulfur on the dehydrogenation of naphthalene on Ni(111) is investigated by using X-ray photoelectron spectroscopy and scanning tunneling microscopy. Sulfur induces a (5 root 3 x 2) surface reconstruction, as previously reported in the literature. The sulfur does not have a strong effect on the dehydrogenation temperature of naphthalene. However, the presence of sulfur leads to a preferred formation of carbidic over graphitic carbon and a strong inhibition of carbon diffusion into the nickel bulk, which is one of the steps of destructive whisker carbon formation described in the catalysis literature., QC 20240216

The instability of molecular electrodes under oxidative/reductive conditions and insufficient understanding of the metal oxide-based systems have slowed down the progress of H2-based fuels. Efficient regeneration of the electrode's performance after prolonged use is another bottleneck of this research. This work represents the first example of a bifunctional and electrochemically regenerable molecular electrode which can be used for the unperturbed production of H2 from water. Pyridyl linkers with flexible arms (-CH2-CH2-) on modified fluorine-doped carbon cloth (FCC) were used to anchor a highly active ruthenium electrocatalyst [RuII(mcbp)(H2O)2] (1) [mcbp2− = 2,6-bis(1-methyl-4-(carboxylate)benzimidazol-2-yl)pyridine]. The pyridine unit of the linker replaces one of the water molecules of 1, which resulted in RuPFCC (ruthenium electrocatalyst anchored on -CH2-CH2-pyridine modified FCC), a high-performing electrode for oxygen evolution reaction [OER, overpotential of ∼215 mV] as well as hydrogen evolution reaction (HER, overpotential of ∼330 mV) at pH 7. A current density of ∼8 mA cm−2 at 2.06 V (vs. RHE) and ∼−6 mA cm−2 at −0.84 V (vs. RHE) with only 0.04 wt% loading of ruthenium was obtained. OER turnover of >7.4 × 103 at 1.81 V in 48 h and HER turnover of >3.6 × 103 at −0.79 V in 3 h were calculated. The activity of the OER anode after 48 h use could be electrochemically regenerated to ∼98% of its original activity while it serves as a HE cathode (evolving hydrogen) for 8 h. This electrode design can also be used for developing ultra-stable molecular electrodes with exciting electrochemical regeneration features, for other proton-dependent electrochemical processes., QC 20231116

The low stability of the electrocatalysts at water oxidation (WO) conditions and the use of expensive noble metals have obstructed large-scale H2 production from water. Herein, we report the electrocatalytic WO activity of a cobalt-containing, water-soluble molecular WO electrocatalyst [CoII(mcbp)(OH2)] (1) [mcbp2−=2,6-bis(1-methyl-4-(carboxylate)benzimidazol-2-yl)pyridine] in homogeneous conditions (overpotential of 510 mV at pH 7 phosphate buffer) and after anchoring it on pyridine-modified fluorine-doped carbon cloth (PFCC). The formation of cobalt phosphate was identified only after 4 h continuous oxygen evolution in homogeneous conditions. Interestingly, a significant enhancement of the stability and WO activity (current density of 5.4 mA/cm2 at 1.75 V) was observed for 1 after anchoring onto PFCC, resulting in a turnover (TO) of >3.6×103 and average TOF of 0.05 s−1 at 1.55 V (pH 7) over 20 h. A total TO of >21×103 over 8 days was calculated. The electrode allowed regeneration of∼ 85 % of the WO activity electrochemically after 36 h of continuous oxygen evolution.

Carbon monoxide (CO) oxidation is considered an important reaction in heterogeneous industrial catalysis and has been extensively studied. Pd supported on SiO2 aerogel catalysts exhibit good catalytic activity toward this reaction owing to their CO bond activation capability and thermal stability. Pd/SiO2 catalysts were investigated using carbon monoxide (CO) oxidation as a model reaction. The catalyst becomes active, and the conversion increases after the temperature reaches the ignition temperature (T-ig). A normal hysteresis in carbon monoxide (CO) oxidation has been observed, where the catalysts continue to exhibit high catalytic activity (CO conversion remains at 100%) during the extinction even at temperatures lower than T-ig. The catalyst was characterized using BET, TEM, XPS, TGA-DSC, and FTIR. In this work, the influence of pretreatment conditions and stability of the active sites on the catalytic activity and hysteresis is presented. The CO oxidation on the Pd/SiO2 catalyst has been attributed to the dissociative adsorption of molecular oxygen and the activation of the C-O bond, followed by diffusion of adsorbates at T-ig to form CO2. Whereas, the hysteresis has been explained by the enhanced stability of the active site caused by thermal effects, pretreatment conditions, Pd-SiO2 support interaction, and PdO formation and decomposition., QC 20210215

Fe-air or Ni-Fe cells can offer low-cost and large-scale sustainable energy storage. At present, they are limited by low coulombic efficiency, low active material use, and poor rate capability. To overcome these challenges, two types of nanostructured doped iron materials were investigated: (1) copper and tin doped iron (CuSn); and (2) tin doped iron (Sn). Single-wall carbon nanotube (SWCNT) was added to the electrode and LiOH to the electrolyte. In the 2 wt. % Cu + 2 wt. % Sn sample, the addition of SWCNT increased the discharge capacity from 430 to 475 mAh g-1, and charge efficiency increased from 83% to 93.5%. With the addition of both SWCNT and LiOH, the charge efficiency and discharge capacity improved to 91% and 603 mAh g-1, respectively. Meanwhile, the 4 wt. % Sn substituted sample performance is not on par with the 2 wt. % Cu + 2 wt. % Sn sample. The dopant elements (Cu and Sn) and additives (SWCNT and LiOH) have a major impact on the electrode performance. To understand the relation between hydrogen evolution and charge current density, we have used in operando charging measurements combined with mass spectrometry to quantify the evolved hydrogen. The electrodes that were subjected to prolonged overcharge upon hydrogen evolution failed rapidly. This insight could help in the development of better charging schemes for the iron electrodes.

This work includes raw and analyzed test data when using a recently developed fatigue test method for miniature laser welds in cobalt-chromium (CoCr) alloy joints [1]: 10.1016/j.jmbbm.2019.07.004. The automization of fatigue tests is crucial for saving costs and personnel resources and that is the reason why the atomization threshold and the resulting spectrum data related to CoCr welds are provided here. The finite element method based stress computation output is provided related to shearing-mode tests to support the dataset as a whole. In addition, the compositional data of the parent material and the laser weld are given., QC 20191128

Ethanol dehydrogenation on metal oxides such as Cu2O is an important reaction for the production of renewable energy by fuel cells both via the production of H-2 fuel and via application in direct alcohol fuel cells. To better understand this reaction, we studied the adsorption, dissociation, and desorption of ethanol on Cu2O(111) and (100) surfaces using high-resolution photoelectron spectroscopy, vibrational sum-frequency generation spectroscopy, and temperature-programmed desorption accompanied by density functional theory calculations. On Cu-2(100), the first layer consists primarily of dissociatively adsorbed ethoxy. Second and third layers of ethanol physisorb at low temperatures and desorb below 200 K. On the Cu2O(111) surface, adsorption is mixed as ethoxy, ethanol, and the products following C-C cleavage, CHx, and OCHx, are found in the first layer. Upon heating, products following both C-C and C-O bond breaking are observed on both surfaces and continued heating accentuates molecular cracking. C-O cleavage occurs more on the (100) surface, whereas on the Cu2O(111) surface, C-C cleavage dominates and occurs at lower temperatures than those for the (100) surface. The increased ability of Cu2O(111) to crack ethanol is explained by the varied surface structure including surface oxygen, electron-rich O vacancies, and Cu., QC 20220201

The effect of sub-monolayer silicon on the oxidation of Al(111) and Al(100) surfaces was investigated using X-ray Photoelectron Spectroscopy (XPS) and density functional theory (DFT) calculations. On both surfaces the adatom site is preferred over substituting Si into the Al-lattice; on Al(100) the four fold hollow site is vastly favored whereas on Al(111) bridge and hollow sites are almost equal in energy. Upon O 2 exposure, Si is not oxidized but buried at the metal/oxide interface under the growing aluminum oxide. On Al(111), Si has a catalytic effect on both the initial oxidation by aiding in creating a higher local oxygen coverage in the early stages of oxidation and, in particular, at higher oxide coverages by facilitating lifting Al from the metal into the oxide. The final oxide, as measured from the Al2p intensity, is 25–30% thicker with Si than without. This observation is valid for both 0.1 monolayer (ML) and 0.3 ML Si coverage. On Al(100), on the other hand, at 0.16 ML Si coverage, the initial oxidation is faster than for the bare surface due to Si island edges being active in the oxide growth. At 0.5 ML Si coverage the oxidation is slower, as the islands coalesce and he amount of edges reduces. Upon oxide formation the effect of Si vanishes as it is overgrown by Al 2 O 3 , and the oxide thickness is only 6% higher than on bare Al(100), for both Si coverages studied. Our findings indicate that, in addition to a vanishing oxygen adsorption energy and Mott potential, a detailed picture of atom exchange and transport at the metal/oxide interface has to be taken into account to explain the limiting oxide thickness., QC 20190402

Miniature laser welds with the root depth in the range of 50-300 pm represent air-tight joints between the components in medical devices, such as those in implants, growth rods, stents and various prostheses. The current work focuses on the development of a fatigue test specimen and procedure to determine fatigue lives of shear-loaded laser welds. A cobalt-chromium (CoCr) alloy is used as a benchmark case. S-N graphs, damage process, and fracture surfaces are studied by applying x-ray analysis, atomic force microscopy, and scanning electron microscopy both before and after the crack onset. A non-linear material model is fitted for the CoCr alloy to run finite element simulations of the damage and deformation. As a result, two tensile-loaded specimen designs are established and the performance is compared to that of a traditional torque-loaded specimen. The new generation specimens show less variation in the determined fatigue lives due to well-defined crack onset point and, therefore, precise weld seam load during the experiments. The fatigue damage concentrates to the welded material and the entire weld experiences fatigue prior to the final, fracture-governed failure phase. For the studied weld seams of hardened CoCr, a regression fatigue limit of 10.8-11.8 MPa, where the stress refers to the arithmetic average shear stress computed along the region dominated by shear loading, is determined., QC 20191010

This article reports the two-step synthesis of NiFeOx nanomaterials and their characterization and bifunctional electrocatalytic activity measurements in alkaline electrolyte for metal-air batteries. The samples were mostly in layered double hydroxide at the initial temperature, but upon heat treatment, they were converted to NiFe2O4 phases. The electrochemical behaviour of the different samples was studied by linear sweep voltammetry and cyclic voltammetry on the glassy carbon electrode. The OER catalyst activity was observed for low mass loadings (0.125 mg cm(-2)), whereas high catalyst loading exhibited the best performance on the ORR side. The sample heat-treated at 250 degrees C delivered the highest bi-functional oxygen evolution and reduction reaction activity (OER/ORR) thanks to its thin-holey nanosheet-like structure with higher nickel oxidation state at 250 degrees C. This work further helps to develop low-cost electrocatalyst development for metal-air batteries.

Isopropanol solution based methylammonium lead triiodide (MAPbI3) is studied during the crystallization process. The crystal growth starts in an unstable suspension far from equilibrium by forming different dendritic patterns and terminates with aggregation of stable cubic crystalline grains into fractal clusters. Using transmission electron microscopy (TEM), the time evolution of a newly mixed suspension was studied over a period of two weeks at room temperature and a sequence of the morphological changes was observed. The crystallization process started with single dendritic growth exhibiting branches at 90 degrees angles to one another. After 4 hours, a multi-dendritic growth pattern and a transformation into small crystalline quantum dots were observed. After a week, clusters of crystal grains were formed into a fractal pattern and these patterns appear to be stable also during the second week. Electron and x-ray diffraction revealed the crystallinity of the quantum dots and the clusters of micrometer-sized crystals. Scanning transmission electron microscope (STEM) together with energy dispersive X-ray spectroscopy (EDS) showed that newly formed large grains, from a one hour old solution, displayed a core-shell structure with higher percentage of Pb atoms as compared to iodine at the surface. In the inner core of the grains the percentage of iodine was slightly higher. The electron diffraction (ED) scan over the newly formed grains revealed a polycrystalline surface whereas the inner part had a single crystal pattern. The same solution, now one-week-old, contained grains with only single crystal patterns in the ED scan and showed no core-shell character or polycrystalline surface. The measured percentage of iodine atoms compared to lead was 2:1 throughout the cross section, which is a quantitative value within the measurement. It can be concluded from these measurements that the suspension approaches higher crystallinity of the perovskite grains in an irreversib

In this paper we demonstrate a process optimization of atomic layer deposited Al2O3 on 4H-SiC resulting in an improved interface and electrical properties. For this purpose the samples have been treated with two pre deposition surface cleaning processes, namely CP1 and CP2. The former is a typical surface cleaning procedure used in SiC processing while the latter have an additional weak RCA1 cleaning step. In addition to the cleaning and deposition, the effects of post dielectric annealing (PDA) at various temperatures in N2O ambient have been investigated. Analyses by scanning electron microscopy show the presence of structural defects on the Al2O3 surface after annealing at 500 and 800 °C. These defects disappear after annealing at 1100 °C, possibly due to densification of the Al2O3 film. Interface analyses have been performed using X-ray photoelectron spectroscopy (XPS) and time-of-flight medium energy ion scattering (ToF MEIS). Both these measurements show the formation of an interfacial SiOx (0 < x < 2) layer for both the CP1 and CP2, displaying an increased thickness for higher temperatures. Furthermore, the quality of the sub-oxide interfacial layer was found to depend on the pre deposition cleaning. In conclusion, an improved interface with better electrical properties is shown for the CP2 sample annealed at 1100 °C, resulting in lower oxide charges, strongly reduced flatband voltage and leakage current, as well as higher breakdown voltage., QC 20180327

Selenols are considered as an alternative to thiols in self-assembled monolayers, but the Se-C bond is one limiting factor for their usefulness. In this study, we address the stability of the Se-C bond by a combined experimental and theoretical investigation of gas phase-deposited hexane selenol (CH3(CH2)(5)SeH) on Au(111) using photoelectron spectroscopy, scanning tunneling microscopy, and density functional theory (DFT). Experimentally, we find that initial adsorption leaves atomic Se on the surface without any carbon left on the surface, whereas further adsorption generates a saturated selenolate layer. The Se 3d component from atomic Se appears at 0.85 eV lower binding energy than the selenolate-related component. DFT calculations show that the most stable structure of selenols on Au(111) is in the form of RSe-Au-SeR complexes adsorbed on the unreconstructed Au(111) surface. This is similar to thiols on Au(111). Calculated Se 3d core-level shifts between elemental Se and selenolate in this structure nicely reproduce the experimentally recorded shifts. Dissociation of RSeH and subsequent formation of RH are found to proceed with high barriers on defect-free Au(111) terraces, with the highest barrier for scissoring R-Se. However, at steps, these barriers are considerably lower, allowing for Se-C bond breaking and hexane desorption, leaving elemental Se at the surface. Hexane is the selenol to selenolate formed by replacing the Se-C bond with a H-C bond by using the hydrogen liberated from transformation., QC 20180328

Adsorption and desorption of methanol on the (111) and (100) surfaces of Cu2O have been studied using high-resolution photoelectron spectroscopy in the temperature range 120–620 K, in combination with density functional theorycalculations and sum frequency generation spectroscopy. The bare (100) surfaceexhibits a (3,0; 1,1) reconstruction but restructures during the adsorption process into a Cu-dimer geometry stabilized by methoxy and hydrogen binding in Cu-bridge sites. During the restructuring process, oxygen atoms from the bulk that can host hydrogen appear on the surface. Heating transforms methoxy to formaldehyde, but further dehydrogenation is limited by the stability of the surface and the limited access to surface oxygen. The (√3 × √3)R30°-reconstructed (111) surface is based on ordered surface oxygen and copper ions and vacancies, which offers a palette of adsorption and reaction sites. Already at 140 K, a mixed layer of methoxy, formaldehyde, and CHxOy is formed. Heating to room temperature leaves OCH and CHx. Thus both CH-bond breaking and CO-scission are active on this surface at low temperature. The higher ability to dehydrogenate methanol on (111) compared to (100) is explained by the multitude of adsorption sites and, in particular, the availability of surfaceoxygen., QC 20170816

We measured the adsorption characteristics of two organic dyes; triphenylamine-cyanoacrylic acid (TPA-C) and phenoxazine (MP13), on TiO2, directly in a solution based on quartz crystal microbalance (QCM). Monitoring the adsorbed amount as a function of dye concentration and during rinsing allows determination of the equilibrium constant and distinction between chemisorbed and physisorbed dye. The measured equilibrium constants are 0.8 mM(-1) for TPA-C and 2.4 mM(-1) for MP13. X-ray photoelectron spectroscopy was used to compare dried chemisorbed layers of TPA-C prepared in solution with TPA-C layers prepared via vacuum sublimation; the two preparation methods render similar spectra except a small contribution of water residues (OH) on the solution prepared samples. Quantitative Nanomechanical Mapping Atomic Force Microscopy (QNM-AFM) shows that physisorbed TPA-C layers are easily removed by scanning the tip across the surface. Although not obvious in height images, adhesion images clearly demonstrate removal of the dye., QC 20190514

The interaction of water vapor and sulfur dioxide (SO2) with single crystal cuprous oxide (Cu2O) surfaces of (100) and (111) termination was studied by photoelectron spectroscopy (PES) and density functional theory (DFT). Exposure to near-ambient pressures of water vapor, at 5 × 10-3 %RH and 293 K, hydroxylates both Cu2O surfaces with OH coverage up to 0.38 copper monolayers (ML) for (100) and 0.25 ML for (111). O 1s surface core level shifts indicate that the hydroxylation lifts the (3,0;1,1) reconstruction of the clean (100) surface. On both clean Cu2O terminations, SO2 adsorbs to unsaturated surface oxygen atoms to form SO3 species with coverage, after a saturating SO2 dose, corresponding to 0.20 ML on the Cu2O(100) surface and 0.09 ML for the Cu2O(111) surface. Our combined DFT and PES results suggest that the SO2 to SO3 transformation is largely facilitated by unsaturated copper atoms at the Cu2O(111) surface. SO3-terminated surfaces exposed to low doses of water vapor (≤100 langmuirs) in ultrahigh vacuum show no adsorption or reaction. However, during exposure to near-ambient pressures of water vapor, the SO3 species dissociate, and sulfur replaces a Cu2O lattice oxygen in a reaction that forms Cu2S. The hydroxylation of the Cu2O surfaces is believed to play a central role in the reaction., QC 20171116

Hexane selenol (CH3(CH2)5SeH) was adsorbed from gas phase in ultra-high vacuum on polycrystalline Cu and studied with synchrotron radiation based photoelectron spectroscopy (PES) and Near edge X-ray absorption fine structure spectroscopy (NEXAFS). Adsorption was done on a bare copper surface at room temperature (RT), on a thin oxide on Cu at room temperature, and on a thin layer of water on Cu at 140 K., QC 20170818

An attractive solution to mitigate tars and also to decompose lighter hydrocarbons in biomass gasification is secondary catalytic reforming, converting hydrocarbons to useful permanent gases. Albeit that it has been in use for a long time in fossil feedstock catalytic steam reforming, understanding of the catalytic processes is still limited. Naphthalene is typically present in the biomass gasification gas and to further understand the elementary steps of naphthalene transformation, we investigated the temperature dependent naphthalene adsorption, dehydrogenation and passivation on Ni(111). TPD (temperature-programmed desorption) and STM (scanning tunneling microscopy) in ultrahigh vacuum environment from 110 K up to 780 K, combined with DFT (density functional theory) were used in the study. Room temperature adsorption results in a flat naphthalene monolayer. DFT favors the dibridge[7] geometry but the potential energy surface is rather smooth and other adsorption geometries may coexist. DFT also reveals a pronounced dearomatization and charge transfer from the adsorbed molecule into the nickel surface. Dehydrogenation occurs in two steps, with two desorption peaks at approximately 450 and 600 K. The first step is due to partial dehydrogenation generating active hydrocarbon species that at higher temperatures migrates over the surface forming graphene. The graphene formation is accompanied by desorption of hydrogen in the high temperature TPD peak. The formation of graphene effectively passivates the surface both for hydrogen adsorption and naphthalene dissociation. In conclusion, the obtained results on the model naphthalene and Ni(111) system, provides insight into elementary steps of naphthalene adsorption, dehydrogenation, and carbon passivation, which may serve as a good starting point for rational design, development and optimization of the Ni catalyst surface, as well as process conditions, for the aromatic hydrocarbon reforming process.