Search

A novel method is presented which permits to assess implanted femoral components with regards to location of fixation and initial stability under cyclic torsional loads. The measurement apparatus tracks the spatial movement at several sites of stem and bone, allowing quantitative analysis of the micromotions and twisting of stem and bone, and the location of torque (force) transfer. Four types of prostheses were compared, which revealed striking differences in torque transfer. Our results for synthetic femurs are consistent with in vivo data on the osseointegration and radiolucensies observed for the stem types of this study. The method can be used to quantitatively compare various stem designs and implantation techniques. [ABSTRACT FROM AUTHOR]

Research into new surface coatings and surface processing methods for prostheses is subject to numerous studies. The aim of this study was to test an innovative biomechanical measuring method for the examination of the ingrowth of bone implants. Using a transcortical model, coated (n=14) or uncoated (n=14) titanic cylinders were implanted into the lateral condyle of 28 New Zealand White Rabbits. After 6 weeks or 6 months the animals were sacrificed and the osseointegration of the implants was evaluated biomechanically and histologically. Up to traction of 50 N the load dependent movement between bone and testing cylinder did not lead to a destruction of the bone-implant-interface. Therefore, biomechanical and histological investigations could be performed in the same specimen. The results of both evaluations showed a significant correlation (correlation coefficient -0.79; p < 0.01) and were absolutely reproducible. With the method of non-destructive mechanical testing, it is possible to halve the number of required animals. Additionally, the results of the biomechanical and histological analysis can be compared and thus serve as an internal control. In summary, the method of non-destructive mechanical testing represents an ideal tool to study new surface coatings and surface processing methods for prostheses.

We performed an experimental study to compare the effectiveness of robotic bone milling (Robodoc and CASPAR) with hand-broaching as regards primary rotational stability of 7 different cementless stems. Using 48 synthetic femora and a specially-designed apparatus, we compared the implant stability of proximal and distal rotational stem displacement (slip) in relation to the cortex. We also measured stem deformation (twist) and the location of torque transfer from stem to cortex (i.e., fixation pattern). 5-ROM, Antega, and ABG stems were more stable in hand-broached femora. Osteolock stems showed no difference between CASPAR and hand preparation, but rotational stability was better in the Robodoc group. G2, VerSys ET and Vision 2000 stems gave increased rotational stability in the robotic groups. When placed too laterally, Vision 2000 showed a pattern of more distal fixation. The findings emphasize the current difficulties in creating a perfect match of robotically-milled cavity and stem geometry to achieve enhanced primary rotational stability. The pattern of fixation seems to depend not only on stem design, but also on canal preparation and stem positioning.

We present an experimental study to determine the effectiveness of computer assisted robotic bone preparation with regard to primary rotational stability in comparison to hand broaching. 5 different cementless stems were standardized implanted in synthetic femora and measured in a specially designed apparatus (displacement in 6 degrees of freedom). In addition the contact areas of the stems and the bone were visualized. The S-ROM- and ABG-stems were more stable in hand broached femora. The Osteolock-, G2- and Vision-2000-stems were more stable in the robot group. The mode of fixation of each implant could be characterized in relation to its position and its stiffness (primary rotational stability). The contact areas differed in some prosthesis in the way of preparation. The findings highlight the current difficulties in creating a perfect match of robotically milled cavity and stem geometry to achieve enhanced stability.

The paper presents a novel method for recording amplitude and phase of 6D-vibrations of a spatial pendulum over a wide frequency range (10 Hz up to 20 kHz). The six degrees of freedom of the pendulum mass were monitored by three electrodynamic stereo pickups. At rest, the tips of the needles and the pendulum's center of mass defined the reference system with respect to which the oscillations of the mass were recorded in terms of their amplitudes and phases. Its small dimensions, constant transfer characteristics, linearity, high dynamics, and virtual lack of reaction onto the moving system over the entire frequency range provided the advantages of the measuring system. This method was used to analyze the spatial 6D-vibrations of the head of a cemented femoral hip endoprosthesis when the femur was stimulated to bending vibrations. The head of the prosthesis carried out axial rotational vibrations at every frequency used to stimulate the femur. The amplitudes of the axial rotations of the cortical bone were small in comparison to the ones of the prosthesis head, indicating that axial rotational vibrations following femur bending vibrations mainly stressed the spongiosa and the cement layer. This was observed over the entire frequency range, including at the low frequencies relevant for gait. Over the low-frequency range, as well as at some of the higher resonance frequencies, stationary instantaneous helical axes characterized the vibrations. The measurements suggest the mechanism that the interface "implant-bone" may already be stressed by axial torsional loads when the femur is loaded by bending impacts that are known to occur during walking.

Aim: Most methods used for the determination of volumetric wear of polyethylene cups are based on the assumption that the head of the prosthesis penetrates the cup in "cylindrical" fashion. The new accurate optical method is independent of this disputable assumption., Method: The articulating surface of the cup is scanned with light and a data set of 60,000 pixels obtained in this way is stored in a computer. Data obtained from used cups were compared with those obtained from unused cups. The volumetric wear was calculated directly by threefold integration. To assess the changes in surface shape, the data are fitted by an ellipsoid whose long axis defines the mean direction of load. A total of 18 retrieved and 3 unused cups of different types were studied., Results: The unused acetabular cups deviated only slightly from ideal hemispheres. The surfaces showed rotational symmetry, and an undulation having an amplitude of 0.1 mm between dome and equator. For all explanted cups, the assumption of cylindrical penetration of the head into the polyethylene was shown not to represent the true situation. The cup expands in all directions, and the volumetric wear is underestimated by 50% with the traditional methods. The data suggest that long-term survival may be jeopardized when the main direction of loading is centered on the dome of the cup. Ceramic heads were associated with smaller rates of volumetric wear., Conclusion: The new optical method is characterised by short measuring times, precision and simple application. Analysis of the wear patterns of polyethylene components using this technique may contribute to a further understanding of the complex mechanisms of aseptic loosening.