Search

Crenosoma striatum is a host-specifi c metastrongiloid nematode causing respiratory tract disease in hedgehogs (Erinaceus europaeus). Since few studies have reported C. striatum in hedgehogs and little genetic data is available concerning this lungworm, this study aimed to determine the occurrence of C. striatum in a population sample of hedgehogs from Portugal, additionally providing morphological, histological and molecular data. From 2017 to 2018 a survey of infection was carried out in 11 necropsied hedgehogs. Worms were extracted from fresh lung tissues and microscopically evaluated. Molecular characterization of partial mitochondrial (12S rRNA) and nuclear (18S rRNA) genes was performed. The presence of lungworms in pulmonary tissues of five hedgehogs (45.5%) was detected. Morphological and histopathological analyses evidenced adult forms of nematodes consistent with C. striatum. Molecular characterization of 18S rRNA genes confirmed the classifi cation as C. striatum. Also, novel genetic data characterizing the mitochondrial (12S rRNA) gene of C. striatum is presented.

Cold spraying (CS) of high-strength materials, e.g., Inconel®625 is still challenging due to the limited material deformability and thus high critical velocities for achieving bonding. Further fine-tuning and optimization of cold spray process parameters are required, to reach higher particle impact velocities and temperatures, while avoiding nozzle clogging. Only then, sufficiently high amounts of well-bonded particle–substrate and particle–particle interfaces can be achieved, assuring high cohesive strength and minimum amounts of porosities. In this study, Inconel®625 powder was cold sprayed on carbon steel substrates, using N2 as propellant gas under different spray parameter sets and different powder sizes for a systematic evaluation. Coating microstructure, porosity, electrical conductivity, hardness, cohesive strength, and residual stress were characterized in as-sprayed condition. Increasing the process gas temperature or pressure leads to low coating porosity of less than 1% and higher electrical conductivity. The as-sprayed coatings show microstructures with highly deformed particles. X-ray diffraction reveals that powder and deposits are present as γ-solid-solution phase without any precipitations. The deposits show high microhardness and compressive residual stresses, which is attributed to work hardening and peening effects. The optimized deposits reach almost bulk material properties and are thus well suited for industrial applications. [ABSTRACT FROM AUTHOR]

Bismuth vanadate (BiVO4) offers high photon efficiencies in solar photo-anodes, due to its suitable semiconductor band gap energies and associated visible light absorption. In well-tuned conditions, such anodes enable green hydrogen generation in photoelectrochemical water splitting cells. Bismuth vanadate films have to ensure high efficiencies in electron/hole pair generation and sufficiently high rates of charge transfer to the conducting substrate and the electrolyte, respectively. Thus, the tuning of coating properties has to aim for high phase purity, good layer integrity as well as optimum diffusion path lengths. In order to explore the potential of aerosol deposition to produce BiVO4 films with high photoelectrochemical activity and to elucidate influences on microstructure and application properties, powder sizes and spraying parameters had to be tailored. By ball milling over durations of up to 20 min, particles sizes in the range from 8.3 down to 0.6 µm were obtained. With respect to spray conditions, the process gas pressure was varied from 1.0 to 2.1 bar corresponding to gas flow rates of 10-40 l/min. The wide range of powder sizes and parameters in aerosol deposition allowed for developing a window of deposition in order to derive the most promising combinations for layer build-up. Optimum parameter sets in application on stainless steel substrates were transferred to FTO-coated glass substrates for backlit cell layouts. The thickness and conductivity of the layers were adjusted to a layer thickness range of 200-500 nm in order to achieve maximum photocurrents. The production of homogeneous, large-scale prototypes demonstrates that aerosol deposition is suitable for processing layers for solar energy harvesting with high photo current densities of up to 3.55 mA/cm2. [ABSTRACT FROM AUTHOR]