Search

This study investigates the performance of different poly(lactic acid) (PLA) composites incorporating agri-food waste additives and commercial lignin, comparing their properties with those of virgin PLA. The following composites were prepared using a single-screw extruder: PLA with 20% rice husk, PLA with 20% wheat straw and PLA with 20% olive pit. Additionally, PLA was blended with commercial lignin at the maximum feasible proportion using the same methodology. The resulting composites were injection-molded into specimens for analysis of their mechanical, thermal and morphological behavior. The primary objectives were to assess the dispersion of the additives within the PLA matrix and to evaluate the mechanical properties of the composites. The results indicate that the addition of high percentages of agricultural residues does not significantly compromise the mechanical properties of the composites. Notably, in the case of the PLA with 20% rice husk composite, the elastic modulus surpassed that of virgin PLA, despite the evident heterogeneity in filler particle sizes. It was feasible to incorporate a higher percentage of agricultural residues compared to commercial lignin, attributed to the larger volume occupied by the latter. [ABSTRACT FROM AUTHOR]

There has been little research into the effects of the water hardness and alkalinity of surface waters on the adsorption of herbicides on activated carbons. The aim of this study was to determine the influence of these water characteristics on fluroxypyr adsorption on different activated carbons. At low fluroxypyr surface concentrations, the amount adsorbed from distilled water was related to the surface hydrophobicity. Surface area of carbons covered by fluroxypyr molecules ranged from 60 to 65%. Variations in fluroxypyr solubility with water hardness and alkalinity showed a salting-in effect. Calcium, magnesium and bicarbonate ions were adsorbed to a varied extent on the activated carbons. The presence of fluroxypyr in solution decreased their adsorption due to a competition effect. K(F) from the Freundlich equation linearly increased with water hardness due to salt-screened electrostatic repulsions between charged fluroxypyr molecules. The amount adsorbed from distilled water was largest at high fluroxypyr solution concentrations, because there was no competition between inorganic ions and fluroxypyr molecules. The column breakthrough volume and the amount adsorbed at breakthrough were smaller in tap versus distilled water. Carbon consumption was lower with activated carbon cloth than with the use of granular activated carbon., ((c) 2009 Elsevier Ltd. All rights reserved.)

A study was conducted on the adsorption kinetics of diuron and amitrole from aqueous solutions on activated carbons of different particle sizes and on an activated carbon fiber. Different kinetic models were applied to the experimental results obtained. A pseudo-second-order rate equation fitted the adsorption kinetics data better than a pseudo-first-order rate equation. Amitrole showed faster adsorption kinetics compared with diuron because of the smaller size of the former herbicide, despite its lower driving force for adsorption. Both reaction rate constants increased when the particle size decreased. The activated carbon fiber and the activated carbon of smallest particle size (0.03 mm) showed similar adsorption kinetics. The intraparticle diffusion rate constant increased with higher initial concentration of herbicides in solution and with lower particle size of the adsorbent. This is because the rise in initial concentration increased the amount adsorbed at equilibrium, and the reduction in particle size increased the number of collisions between adsorbate and adsorbent particles. Demineralization of the activated carbon with particle size of 0.5mm had practically no effect on the adsorption kinetics.

This study investigated the removal of the herbicides diuron and amitrole from water under static and dynamic conditions using different activated carbons in the form of fibers, cloth, and grains. In all cases, there was much greater adsorption of diuron than of amitrole due to the lower solubility, greater hydrophobicity, and larger dipolar moment of the former. The activated carbon cloth was the best adsorbent for diuron under dynamic conditions because it had the largest mesopore volume, water-accessible pore volume, and surface area. However, the best adsorbent for amitrole under dynamic conditions was the granular activated carbon due to its higher surface basicity. Comparisons using the best adsorbent for each herbicide showed that diuron was removed by the activated carbon more efficiently compared with amitrole under both dynamic and static conditions.

A study was conducted on the effects of carbon surface chemistry, solution pH, and ionic strength on the removal of diuron and amitrole from aqueous solutions by adsorption on an as-received and oxidized activated carbon fiber. Results obtained were explained by the surface characteristics of the adsorbents and the characteristics of the herbicide molecules. Under the experimental conditions used, diuron uptake was much higher than that of amitrole, despite its larger molecular dimensions, due to the lesser water solubility, greater hydrophobicity, and larger dipolar moment of diuron compared with amitrole. Uptake variations associated with differences in carbon surface oxidation, solution pH, and ionic strength were explained by corresponding changes in electrostatic, hydrophobic, and van der Waals interactions.