Search

A comprehensive investigation into the design and electrochemical optimization of composite electrodes consisting of poly(3,4-ethylenedioxythiophene) (PEDOT)/graphene oxide (GO)/Methanococcus deltae and reduced graphene oxide (rGO)/Methanococcus deltae hybrids, anchored onto stainless-steel (SS) substrates, has been conducted. The GO and rGO materials were synthesized using a modified Hummer method. The resulting SS/PEDOT/GO and SS/PEDOT/rGO composite electrodes were subjected to systematic electrochemical characterization, focusing on the PEDOT p-type and n-type doping/undoping processes within diverse solvent environments (CH3CN and H2O) and electrolyte compositions (LiClO4 and KCl). Raman spectroscopy analysis confirmed the successful integration of graphene derivatives into the electrode structures, while field-emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) revealed increased surface roughness upon GO and rGO incorporation. This increase in surface roughness is believed to enhance the adhesion of Methanococcus deltae microorganisms and facilitate efficient electron transport. Electrochemical measurements showed that the resulting SS/PEDOT/GO and SS/PEDOT/rGO anodes exhibit remarkable electrocatalytic activity. The SS/PEDOT/GO electrode achieved a maximum power density of 1014.420 mW/cm2, while the SS/PEDOT/rGO electrode reached 632.019 mW/cm2. [ABSTRACT FROM AUTHOR]

The influence of residual cuts on the deactivation of hierarchical Y zeolite-based catalysts during the co-processing of vacuum gas oil (VGO) with atmospheric residue (ATR) was investigated. The experiments were conducted in a laboratory-scale MAT-type reactor. The conversion of VGO, ATR, and their 70:30 (mass basis) mixture was examined using two composite catalysts: Cat.Y.0.00 and Cat.Y.0.20. The operating conditions closely resembled those of the commercial catalytic cracking process (550 °C and contact times of 10 to 50 s). When ATR was processed individually, the conversion remained below 50 wt%. However, significant improvements in conversion rates were achieved and catalyst deactivation was mitigated when ATR was co-processed with VGO. Notably, the BET surface area and average mesopore volume were adversely impacted by ATR, which also led to the accumulation of high levels of metals and nitrogen on the spent catalyst, detrimentally affecting its acidic and structural properties. Moreover, substantial coke deposition occurred during ATR cracking. The soluble and insoluble coke analysis revealed H/C ratio values of up to 0.36, indicative of polycondensed coke structures with more than ten aromatic rings. The nature of the coke was confirmed through TPO and FTIR analyses. Interestingly, the CatY.0.20 catalyst exhibited less activity loss, retaining superior acid and structural properties. Co-processing Colombian atmospheric residue with ATR loadings of 30 wt% (higher than the typical 20 wt%) in catalysts formulated with hierarchical zeolites presents a promising alternative for commercial applications. This research opens avenues for optimizing catalytic cracking processes. [ABSTRACT FROM AUTHOR]

Commercial NH4-Beta and Na-ZSM-5 zeolites were fluorinated with different amounts of NH4F and using different procedures (room temperature, conventional refluxing, microwave refluxing). Samples were characterized by XRD, N2 physisorption, FTIR, 1H NMR, SEM-EDS, and TGA of adsorbed cyclohexylamine. An increase in the concentration of NH4F led to fluorinated zeolites with higher surface areas and slightly lower amounts of Brønsted acid sites due to some dealumination. Fluorination by conventional or microwave refluxing at shorter times did not dealuminate ZSM-5, resulting in the formation of higher particle sizes. Ni/fluorinated beta catalysts were more active than Ni/fluorinated ZSM-5 catalysts for the hydrodeoxygenation of guaiacol at 180 °C and 15 bar of H2 for 1 h due to their higher amount of acid sites. The appropriate proportion of metallic and Brønsted acid centers allowed for the selective obtention of cyclohexane (58%) for the Ni supported on beta fluorinated with NH4F 0.1 M catalyst. The combination of this fluorinated beta to a Ni/ordered mesoporous carbon catalyst significantly boosted its selectivity to cyclohexane from 0 to 65%. Fluorinated ZSM-5 samples, although having stronger Brønsted acid sites, as observed by 1H NMR, they had lower amounts, leading to higher selectivity to cyclohexanol when used as catalytic supports. [ABSTRACT FROM AUTHOR]

The performance of catalysts prepared from hierarchical Y zeolites has been studied during the conversion of vacuum gas oil (VGO) into higher-value products. Two different catalysts have been studied: CatY.0.00 was obtained from the standard zeolite (Y-0.00-M: without alkaline treatment) and CatY.0.20 was prepared from the desilicated zeolite (Y-0-20-M: treated with 0.20 M NaOH). The cracking tests were carried out in a microactivity test (MAT) unit with a fixed-bed reactor at 550 ◦C in the 20–50 s reaction time range, with a catalyst mass of 3 g and a mass flow rate of VGO of 2.0 g/min. The products obtained were grouped according to their boiling point range in dry gas (DG), liquefied petroleum gas (LPG), naphtha, and coke. The results showed a greater conversion and selectivity to gasoline with the CatY.0.20 catalyst, along with improved quality (RON) of the C5–C12 cut. Conversely, the CatY.0.00 catalyst (obtained from the Y-0.00-M zeolite) showed greater selectivity to gases (DG and LPG), attributable to the electronic confinement effect within the microporous channels of the zeolite. The nature of coke has been studied using different analysis techniques and the impact on the catalysts by comparing the properties of the fresh and deactivated catalysts. The coke deposited on the catalyst surfaces was responsible for the loss of activity; however, the CatY.0.20 catalyst showed greater resistance to deactivation by coke, despite showing the highest selectivity. Given that the reaction occurs in the acid sites of the zeolite and not in the matrix, the increased degree of mesoporosity of the zeolite in the CatY.0.20 catalyst facilitated the outward diffusion of products from the zeolitic channels to the matrix, thereby preserving greater activity [ABSTRACT FROM AUTHOR]

Ir and IrSn catalysts with different Sn contents (0.5, 0.7 and 0.9 wt%) were prepared using MgAl2O4 supports synthesized using two different techniques (the citrate–nitrate combustion and coprecipitation methods). Both supports, with a spinel structure, presented low acidity and good textural properties. However, the support prepared by coprecipitation had higher specific surface area and pore volume than the one prepared by combustion, which would favor the dispersion of the metals to be deposited. Likewise, during the preparation of the catalytic materials, a very good interaction was achieved between the metals and both supports, which was confirmed by the presence of sub-nanometer atomic clusters in the mono- and bimetallic catalysts. Regarding the catalytic properties, while the monometallic Ir/MgAl2O4 samples lead to a very low conversion of n-butane and a selectivity towards hydrogenolysis products, the addition of Sn to Ir increases the conversion, decreases hydrogenolysis and therefore sharply increases the selectivity towards the different butenes. Catalysts with higher Sn loadings present better catalytic behavior. One of the roles of the Sn promoter would be to geometrically modify the Ir clusters, drastically decreasing the hydrogenolytic activity. This effect, added to the strong electronic modification of the Ir sites by the action of Sn, with probable Ir-Sn alloy formation, is responsible for the high catalytic performance of these bimetallic catalysts. [ABSTRACT FROM AUTHOR]

In the information contained herein, we fabricated biochar by means of a pyrolysis process; it used Prosopis juliflora waste (PJW) as a biomass source. The physical and chemical material characterization was carried out through FTIR, thermogravimetric, BET-N2 isotherm, and SEM-EDX assays. We studied the methylene orange (MO) adsorption onto PWJ biochar. The PJW biochar displayed a maximum percentage of MO removal of 64%. The results of the adsorption study indicated that Temkin isotherm was suitable to describe the MO adsorption process on PJW biochar; it suggests that the MO adsorption on PJW biochar could be a multi-layer adsorption process. Results showed that the pseudo-second-order model was accurate in demonstrating the MO adsorption on PJW (k2 = 0.295 g mg−1min−1; qe = 8.31 mg g−1). Furthermore, the results made known that the MO removal by PJW biochar was endothermic (ΔH = 12.7 kJ/mol) and a spontaneous process (ΔG = −0.954 kJ/mol). The reusability test disclosed that after four consecutive adsorption/desorption cycles, the PWJ biochar reduced its MO removal by only 4.3%. [ABSTRACT FROM AUTHOR]

Copyright of Prospectiva (1692-8261) is the property of Universidad Autonoma del Caribe and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)