Search

Severe infantile tracheobronchomalacia (TBM) is often treated with invasive surgery and fixed‐size implants to support the trachea during respiration. A novel 3D‐printed extra‐luminal splint has been developed as a flexible and bioresorbable alternative. Therefore, the goal of the present study was to use an in vitro breathing simulator model to comprehensively evaluate the structural stiffness and failure modes of two sizes of a novel bioresorbable 3D‐printed splint design under a range of physiological degradation conditions. Two thicknesses, 2 mm and 3 mm, of a novel 3D‐printed bioresorbable splint were evaluated under two different degradation conditions, phosphate‐buffered saline (PBS) and sodium hydroxide (NaOH). The splints were subjected to simulated breathing loading, involving a cyclic opening and closing of the splint by 2 mm, for a targeted duration of 7.5 to 30 million cycles. A separate new set of splints were statically soaked in their respective degradation condition for a comparative analysis of the effects of cyclic loading by the degradation medium. After successfully simulated breathing or static soaking, non‐destructive tensile and compressive strengths were evaluated, and overall stiffness was calculated from destructive tensile testing. The present study indicates that the splints were more significantly degraded under simulated breathing conditions than under soaking. Cyclic simulated breathing specimens failed far earlier than the intended duration of loading. Over time, both 2 mm and 3 mm splints became increasingly more flexible when subjected to the static degradation conditions. Interestingly, there was little difference in the compressive and tensile strengths of the 2 mm and 3 mm thickness splints. The bioresorbable nature of PCL offers a valuable advantage as it eliminates the need for splint removal surgery and increases device flexibility over time with degradation. This increased flexibility is crucial because it allows for uninhibited growth and development of the infant's trachea over the intended use period of 2 years. The results of this study confirm that the splints were able to withstand tensile forces to prevent tracheal collapse. This study further supports the successful use of 3D‐printed splints in the treatment of infantile TBM. [ABSTRACT FROM AUTHOR]

PurposeAnterior cruciate ligament (ACL) rupture is increasingly common in adolescents. Time between ACL rupture and surgical reconstruction, surgical wait time, is related to concurrent meniscal tear incidence and possibly tear pattern. This study defines the relationship between meniscal tear characteristics and surgical wait time in adolescents with ACL rupture.MethodsOne-hundred and twenty-one consecutive adolescent (median age 16.1 years, range 9-19 years) ACL rupture patients undergoing primary ACL reconstruction were studied. All had documented surgical wait time, preoperative and 6-month post-operative outcome (Lysholm and pedi-IKDC) scores, and intraoperative meniscus tear characteristics. Meniscal tear severity was graded according to the Lawrence and Anderson system: non-surgical: grade 1; reparable: grade 2-3; irreparable: grade 4-5. Significant tears were defined as at least grade 2.ResultsAverage age at surgery was 16.1 years. 48.7 % had surgical wait time greater than 6 months. 42.5 % of menisci were torn. With surgical wait time 6 months, medial tear incidence increased (50 vs 21 %, p 6 months. Public insurance was a risk factor for longer surgical wait time and meniscus tear.

Pseudotumor-like periprosthetic tissue reactions around metal-on-metal (M-M) hip replacements can cause pain and lead to revision surgery. The cause of these reactions is not well understood but could be due to excessive wear, or metal hypersensitivity or an as-yet unknown cause. The tissue features may help distinguish reactions to high wear from those with suspected metal hypersensitivity.We therefore examined the synovial lining integrity, inflammatory cell infiltrates, tissue organization, necrosis and metal wear particles of pseudotumor-like tissues from M-M hips revised for suspected high wear related and suspected metal hypersensitivity causes.Tissue samples from 32 revised hip replacements with pseudotumor-like reactions were studied. A 10-point histological score was used to rank the degree of aseptic lymphocytic vasculitis-associated lesions (ALVAL) by examination of synovial lining integrity, inflammatory cell infiltrates, and tissue organization. Lymphocytes, macrophages, plasma cells, giant cells, necrosis and metal wear particles were semiquantitatively rated. Implant wear was measured with a coordinate measuring machine. The cases were divided into those suspected of having high wear and those suspected of having metal hypersensitivity based on clinical, radiographic and retrieval findings. The Mann-Whitney test was used to compare the histological features in these two groups.The tissues from patients revised for suspected high wear had a lower ALVAL score, fewer lymphocytes, but more macrophages and metal particles than those tissues from hips revised for pain and suspected metal hypersensitivity. The highest ALVAL scores occurred in patients who were revised for pain and suspected metal hypersensitivity. Component wear was lower in that group.Pseudotumor-like reactions can be caused by high wear, but may also occur around implants with low wear, likely because of a metal hypersensitivity reaction. Histologic features including synovial integrity, inflammatory cell infiltrates, tissue organization, and metal particles may help differentiate these causes.Painful hips with periprosthetic masses may be caused by high wear, but if this can be ruled out, metal hypersensitivity should be considered.

Purpose: Composite models have become commonplace for the assessment of fixation and stability of total joint replacements; however, there are no comparable models for the cervical spine to evaluate fixation. The goal of this study was to create the framework for a tunable non‐homogeneous model of cervical vertebral body by identifying the relationships between strength, in‐fill density, and lattice structure and creating a final architectural framework for specific strengths to be applied to the model. Methods: The range of material properties for cervical spine were identified from literature. Using additive manufacturing software, rectangular prints with three lattice structures, gyroid, triangle, zig‐zag, and a range of in‐fill densities were 3D‐printed. The compressive and shear strengths for all combinations were calculated in the axial and coronal planes. Eleven unique vertebral regions were selected to represent the distribution of density. Each bone density was converted to strength and subsequently correlated to the lattice structure and in‐fill density with the desired material properties. Finally, a complete cervical vertebra model was 3D‐printed to ensure sufficient print quality. Results: Materials testing identified a relationship between in‐fill densities and strength for all lattice structures. The axial compressive strength of the gyroid specimens ranged from 1.5 MPa at 10% infill to 31.3 MPa at 100% infill and the triangle structure ranged from 2.7 MPa at 10% infill to 58.4 MPa at 100% infill. Based on these results, a cervical vertebra model was created utilizing cervical cancellous strength values and the corresponding in‐fill density and lattice structure combination. This model was then printed with 11 different in‐fill densities ranging from 33% gyroid to 84% triangle to ensure successful integration of the non‐homogeneous in‐fill densities and lattice structures. Conclusions: The findings from this study introduced a framework for using additive manufacturing to create a tunable, customizable biomimetic model of a cervical vertebra. [ABSTRACT FROM AUTHOR]