Search

Nickel-rich layered oxide cathodes such as NMC811 (LixNi0.8Mn0.1Co0.1O2) currently have the highest practical capacities of cathodes used commercially, approaching 200 mAh/g. Lithium is removed from NMC811 via a solid-solution behavior when delithiated to xLi > 0.10, maintaining the same layered (O3 structure) throughout as observed via operando diffraction measurements. Although it is possible to further delithiate NMC811, it is kinetically challenging, and there are significant side reactions between the electrolyte and cathode surface. Here, small format, NMC811-graphite pouch cells were charged to high voltages at elevated temperatures and held for days to access high states of delithiation. Rietveld refinements on high-resolution diffraction data and indexing of selected area electron diffraction patterns, both acquired ex situ, show that NMC811 undergoes a partial and reversible transition from the O3 to the O1 phase under these conditions. The O1 phase fraction depends not only on the concentration of intercalated lithium but also on the hold temperature and hold time, indicating that the phase transition is kinetically controlled. 1H NMR spectroscopy shows that the proton concentration decreases with O1 phase fraction and is not, therefore, likely to be driving the O3-O1 phase transition.

High-resolution analysis of biomolecules has brought unprecedented insights into fundamental biological processes and dramatically advanced biosensing. Notwithstanding the ongoing resolution revolution in electron microscopy and optical imaging, only a few methods are presently available for high-resolution analysis of unlabeled single molecules in their native states. Here, label-free electrical sensing of structured single molecules with a spatial resolution down to single-digit nanometers is demonstrated. Using a narrow solid-state nanopore, the passage of a series of nanostructures attached to a freely translocating DNA molecule is detected, resolving individual nanostructures placed as close as 6 nm apart and with a surface-to-surface gap distance of only 2 nm. Such super-resolution ability is attributed to the nanostructure-induced enhancement of the electric field at the tip of the nanopore. This work demonstrates a general approach to improving the resolution of single-molecule nanopore sensing and presents a critical advance towards label-free, high-resolution DNA sequence mapping, and digital information storage independent of molecular motors.

Perovskite light-emitting diodes (LEDs) have attracted broad attention due to their rapidly increasing external quantum efficiencies (EQEs)1-15. However, most high EQEs of perovskite LEDs are reported at low current densities (

2H-Benzotriazol-2-ylethylammonium bromide and iodide and its difluorinated derivatives are synthesized and employed as interlayers for passivation of formamidinium lead triiodide (FAPbI3) solar cells. In combination with PbI2 and PbBr2, these benzotriazole derivatives form two-dimensional (2D) Ruddlesden-Popper perovskites (RPPs) as evidenced by their crystal structures and thin film characteristics. When used to passivate n-i-p FAPbI3 solar cells, the power conversion efficiency improves from 20% to close to 22% by enhancing the open-circuit voltage. Quasi-Fermi level splitting experiments and scanning electron microscopy cathodoluminescence hyperspectral imaging reveal that passivation provides a reduced nonradiative recombi-nation at the interface between the perovskite and hole transport layer. Photoluminescence spectroscopy, angle-resolved grazing-incidence wide-angle X-ray scattering, and depth profiling X-ray photoelectron spectroscopy studies of the 2D/three-dimensional (3D) interface between the benzotriazole RPP and FAPbI3 show that a nonuniform layer of 2D perovskites is enough to passivate defects, enhance charge extraction, and decrease nonradiative recombination. The research has received funding from the Ministry of Education, Culture, and Science (Gravity program 024.001.035) and the Netherlands Organization for Scientific Research via a Spinoza grant. This work of B.T.v.G. is part of the Advanced Research Center for Chemical Building Blocks, ARC CBBC, which is cofounded and cofinanced by the Netherlands Organization for Scientific Research (NWO) and the Netherlands Ministry of Economic Affairs (project 2016.03.Tue). W.T.M.v.G., K.V.H., L.L., and D.V. acknowledge the Research Foundation Flanders (FWO) for the funding of the SBO project PROCEED (S002019N) and the senior FWO research projects G043320N and G0A8723N. A.M. acknowledges the FWO for the funding of his FWO fundamental research PhD grant (1115721N). This study was supported by the Special Research Fund (BOF) of Hasselt University (BOF22PD01). J.F.O. acknowledges funding from the Engineering and Physical Sciences Research Council (EPSRC) Nano Doctoral Training Centre (EP/L015978/1).

Funder: Engineering and Physical Sciences Research Council; Id: http://dx.doi.org/10.13039/501100000266, Funder: National University of Ireland Travelling Studentship, Funder: European Research Council; Id: http://dx.doi.org/10.13039/501100000781, The interaction of high-energy electrons and X-ray photons with beam-sensitive semiconductors such as halide perovskites is essential for the characterisation and understanding of these optoelectronic materials. Using nano-probe diffraction techniques, which can investigate physical properties on the nanoscale, we perform studies of the interaction of electron and X-ray radiation with state-of-the-art (FA0.79MA0.16Cs0.05)Pb(I0.83Br0.17)3 hybrid halide perovskite films (FA, formamidinium; MA, methylammonium). We track the changes in the local crystal structure as a function of fluence using scanning electron diffraction and synchrotron nano X-ray diffraction techniques. We identify perovskite grains from which additional reflections, corresponding to PbBr2, appear as a crystalline degradation phase after fluences of ~200 e-Å-2. These changes are concomitant with the formation of small PbI2 crystallites at the adjacent high-angle grain boundaries, with the formation of pinholes, and with a phase transition from tetragonal to cubic. A similar degradation pathway is caused by photon irradiation in nano-X-ray diffraction, suggesting common underlying mechanisms. Our approach explores the radiation limits of these materials and provides a description of the degradation pathways on the nanoscale. Addressing high-angle grain boundaries will be critical for the further improvement of halide polycrystalline film stability, especially for applications vulnerable to high-energy radiation such as space photovoltaics.

The use of pulsed mode scanning electron microscopy cathodoluminescence (CL) for both hyperspectral mapping and time-resolved measurements is found to be useful for the study of hybrid perovskite films, a class of ionic semiconductors that have been shown to be beam sensitive. A range of acquisition parameters is analysed, including beam current and beam mode (either continuous or pulsed operation), and their effect on the CL emission is discussed. Under optimized acquisition conditions, using a pulsed electron beam, the heterogeneity of the emission properties of hybrid perovskite films can be resolved via the acquisition of CL hyperspectral maps. These optimized parameters also enable the acquisition of time-resolved CL of polycrystalline films, showing significantly shorter lived charge carriers dynamics compared to the photoluminescence analogue, hinting at additional electron beam-specimen interactions to be further investigated. This work represents a promising step to investigate hybrid perovskite semiconductors at the nanoscale with CL.

Quantitative chemical analysis on the nanoscale provides valuable information on materials and devices which can be used to guide further improvements to their performance. In particular, emerging families of technologically relevant composite materials such as organic–inorganic hybrid halide perovskites and metal-organic frameworks stand to benefit greatly from such characterization. However, these nanocomposites are also vulnerable to damage induced by analytical probes such as electron, X-ray, or neutron beams. Here the effect of electrons on a model hybrid halide perovskite is investigated, focusing on the acquisition parameters appropriate for energy-dispersive X-ray spectroscopy in a scanning transmission electron microscope (STEM-EDX). The acquisition parameters are systematically varied to examine the relationship between electron dose, data quality, and beam damage. Five metrics are outlined to assess the quality of STEM-EDX data and severity of beam damage, further validated by dark field STEM imaging. Loss of iodine through vacancy creation is found to be the primary manifestation of electron beam damage in the perovskite specimen, and iodine content is seen to decrease exponentially with electron dose. This work demonstrates data acquisition and analysis strategies that can be used for studying electron beam damage and for achieving reliable quantification for a broad range of beam-sensitive materials.

IL@MOF (IL: ionic liquid; MOF: metal-organic framework) materials have been proposed as a candidate for solid-state electrolytes, combining the inherent non-flammability and high thermal and chemical stability of the ionic liquid with the host-guest interactions of the MOF. In this work, we compare the structure and ionic conductivity of a sodium ion containing IL@MOF composite formed from a microcrystalline powder of the zeolitic imidazolate framework (ZIF), ZIF-8 with a hierarchically porous sample of ZIF-8 containing both micro- and mesopores from a sol-gel synthesis. Although the crystallographic structures were shown to be the same by X-ray diffraction, significant differences in particle size, packing and morphology were identified by electron microscopy techniques which highlight the origins of the hierarchical porosity. After incorporation of Na0.1EMIM0.9TFSI (abbreviated to NaIL; EMIM = 1-ethyl-3-methylimidazolium; TFSI = bis(trifluoromethylsulfonyl)imide), the hierarchically porous composite exhibited a 40% greater filling capacity than the purely microporous sample which was confirmed by elemental analysis and digestive proton NMR. Finally, the ionic conductivity properties of the composite materials were probed by electrochemical impedance spectroscopy. The results showed that despite the 40% increased loading of NaIL in the NaIL@ZIF-8micro sample, the ionic conductivities at 25 °C were 8.4 × 10-6 and 1.6 × 10-5 S cm-1 for NaIL@ZIF-8meso and NaIL@ZIF-8micro respectively. These results exemplify the importance of the long range, continuous ion pathways contributed by the microcrystalline pores, as well as the limited contribution from the discontinuous mesopores to the overall ionic conductivity.

The operation of halide perovskite optoelectronic devices, including solar cells and LEDs, is strongly influenced by the mobility of ions comprising the crystal structure. This peculiarity is particularly true when considering the long‐term stability of devices. A detailed understanding of the ion migration‐driven degradation pathways is critical to design effective stabilization strategies. Nonetheless, despite substantial research in this first decade of perovskite photovoltaics, the long‐term effects of ion migration remain elusive due to the complex chemistry of lead halide perovskites. By linking materials chemistry to device optoelectronics, this study highlights that electrical bias‐induced perovskite amorphization and phase segregation is a crucial degradation mechanism in planar mixed halide perovskite solar cells. Depending on the biasing potential and the injected charge, halide segregation occurs, forming crystalline iodide‐rich domains, which govern light emission and participate in light absorption and photocurrent generation. Additionally, the loss of crystallinity limits charge collection efficiency and eventually degrades the device performance.

Hybrid metal halide perovskites have emerged as a potential photovoltaic material for low-cost thin film solar cells due to their excellent optoelectronic properties. However, high efficiencies obtained with lab-scale cells are difficult to replicate in large modules. The upscaling process requires careful optimization of multiple steps, such as laser scribing, which divides a module into serially connected cells using a pulsed laser beam. In this work, we characterize the effect of laser scribing on the perovskite layer adjacent to a P3 scribe line using analytical scanning and cross-sectional transmission electron microscopy techniques. We demonstrate that lateral flow of residual thermal energy from picosecond laser pulses decomposes the perovskite layer over extended length scales. We propose that the exact nature of the change in perovskite composition is determined by the presence of preexisting PbI2 grains and hence by the original perovskite formation reaction. Furthermore, we show that along the P3 lines, the indium tin oxide contact is also damaged by high-fluence pulses. Our results provide a deeper understanding on the interaction between laser pulses and perovskite solar modules, highlighting the need to minimize material damage by careful tuning of both laser parameters and the device fabrication procedure.

© 2019 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim In perovskite solar cells (PSCs), the interfaces are a weak link with respect to degradation. Electrochemical reactivity of the perovskite's halides has been reported for both molecular and polymeric hole selective layers (HSLs), and here it is shown that also NiO brings about this decomposition mechanism. Employing NiO as an HSL in p–i–n PSCs with power conversion efficiency (PCE) of 16.8%, noncapacitive hysteresis is found in the dark, which is attributable to the bias-induced degradation of perovskite/NiO interface. The possibility of electrochemically decoupling NiO from the perovskite via the introduction of a buffer layer is explored. Employing a hybrid magnesium-organic interlayer, the noncapacitive hysteresis is entirely suppressed and the device's electrical stability is improved. At the same time, the PCE is improved up to 18% thanks to reduced interfacial charge recombination, which enables more efficient hole collection resulting in higher Voc and FF.

Halide perovskites are emerging as valid alternatives to conventional photovoltaic active materials owing to their low cost and high device performances. This material family also shows exceptional tunability of properties by varying chemical components, crystal structure, and dimensionality, providing a unique set of building blocks for new structures. Here, highly stable self-assembled lead–tin perovskite heterostructures formed between low bandgap 3D and higher bandgap 2D components are demonstrated. A combination of surface-sensitive X-ray diffraction, spatially resolved photoluminescence, and electron microscopy measurements is used to reveal that microstructural heterojunctions form between high bandgap 2D surface crystallites and lower bandgap 3D domains. Furthermore, in situ X-ray diffraction measurements are used during film formation to show that an ammonium thiocyanate additive delays formation of the 3D component and thus provides a tunable lever to substantially increase the fraction of 2D surface crystallites. These novel heterostructures will find use in bottom cells for stable tandem photovoltaics with a surface 2D layer passivating the 3D material, or in energy transfer devices requiring controlled energy flow from localized surface crystallites to the bulk.

Operational stability of perovskite solar cells (PSCs) is rapidly becoming one of the pressing bottlenecks for their upscaling and integration of such promising photovoltaic technology. Instability of the hole transport layer (HTL) has been considered as one of the potential origins of short life-time of the PSCs. In this work, by varying the molecular weight (MW) of doped poly(triarylamine)(PTAA) HTL, we improved by one order of magnitude the charge mobility inside the HTL and the charge transfer at the perovskite/HTL interface. We demonstrate that this occurs via the enhancement of polaron delocalization on the polymeric chains through the combined effect of doping strategy and MW tuning. By using high MW PTAA doped combining three different dopant, we demonstrate stable PSCs with typical power conversion efficiencies above 20%, retain more than 90% of the initial efficiency after 1080 h thermal stress at 85 °C and 87% of initial efficiency after 160 h exposure against 1 sun light soaking. By using this doping-MW strategy, we realized perovskite solar modules with an efficiency of 17% on an active area of 43 cm2, keeping above 90% of the initial efficiency after 800 h thermal stress at 85 °C. These results, obtained in ambient conditions, pave the way toward the industrialization of PSC-based photovoltaic technology.

The technology of perovskite-based solar cells is evolving rapidly, reaching certified power conversion efficiency values now exceeding 20 %. One of the main drawbacks hindering progress in the field is the long-term stability of the cells: the mixed halide perovskites used in most devices are sensitive to humidity and degrade on a timescale varying from hours to weeks. The degradation mechanisms are poorly understood, but likely arise from combined physical and chemical modifications at the nanometer scale. The characterization of pristine and degraded materials is difficult owing to their complex chemical and physical structure and their relatively poor stability. In this work, we investigated the changes in local composition and morphology of a standard device after 2 months of air exposure in the dark, using scanning transmission electron microscopy (STEM) with nanometer resolution for imaging and analysis. Because of a state-of-the-art technique that combines STEM and energy dispersive X-ray spectroscopy (EDX), and the use of different decomposition algorithms for multivariate analysis, we highlighted the migration of elements across the interfaces between the layers comprising the device. We also noticed a morphological degradation of the hole-transporting layer (HTL), representing one of the main factors enabling the infiltration of moisture in the device, which results in reduced performance.

The power conversion efficiency of organic-inorganic hybrid perovskite solar cells has soared over the past ten years and currently rivals those of crystalline silicon and other thin-film solar cells. Most of the research effort so far has been focused on three-dimensional (3 D) perovskite crystals, producing devices with very high efficiency but poor operational and environmental stability. Two-dimensional (2 D) Ruddlesden-Popper perovskite has recently shown its potential as a highly stable light absorber, albeit with low efficiency. This work reviews the current progress in attaining both high efficiency and stability in solar cells by using 2 D perovskite. In particular, the focus is on multidimensional perovskite as a way to combine the best characteristics of 3 D and 2 D perovskites. Future challenges and potential methods to boost the performance of multidimensional perovskite solar cells further are briefly presented.

Quasi-1D-hyperbranched TiO2 nanostructures are grown via pulsed laser deposition and sensitized with thin layers of CdS to act as a highly efficient photoelectrochemical photoanode. The device properties are systematically investigated by optimizing the height of TiO2 scaffold structure and thickness of the CdS sensitizing layer, achieving photocurrent values up to 6.6 mA cm-2 and reaching saturation with applied biases as low as 0.35 VRHE. The high internal conversion efficiency of these devices is to be found in the efficient charge generation and injection of the thin CdS photoactive film and in the enhanced charge transport properties of the hyperbranched TiO2 scaffold. Hence, the proposed device represents a promising architecture for heterostructures capable of achieving high solar-to-hydrogen efficiency.

Hybrid structures consisting of functional materials enhanced by carbon nanotubes (CNTs) have potential for a variety of high impact applications, as shown by the impressive progress in sensing and mechanical applications enabled by CNT-enhanced materials. The hierarchical organisation of CNTs with other materials is key to the design of macroscale devices benefiting from the unique properties of individual CNTs, provided CNT density, morphology and binding with other materials are optimized. In this paper, we provide an analysis of a continuous aerosol process to create a hybrid hierarchical sea urchin structure with CNTs organized around a functional metal oxide core. We propose a new mechanism for the growth of these carbon nanotube sea urchins (CNTSU) and give new insight into their chemical composition. To corroborate the new mechanism, we examine the influence of CNT growth conditions on CNTSU morphology and demonstrate a new in-line characterisation technique to continuously monitor aerosol CNT growth during synthesis, which enables industrial-scale production optimization. Based upon the new formation mechanism we describe the first substrate-based chemical vapour deposition growth of CNTSUs which increases CNT length and improves G to D ratio, which also allows for the formation of CNTSU carpets with unique structures.

Organic-inorganic hybrid perovskite solar cells have exhibited power conversion efficiencies comparable to more established PV technologies thanks to their favourable optoelectronic properties, but low operational stability inhibits their commercialisation and widespread use. Many degradation pathways are possible and most of them are not currently well understood at the nanoscale due to the difficulty of characterising a perovskite solar cell’s complex nanostructure. This work reviews the application of in-situ and operando electron microscopy to visualise the dynamic processes that occur in perovskite solar cells as various stimuli are applied inside a microscope column. Additionally, potential challenges and an outlook on future uses of this technique are briefly discussed.

The direct chemical vapour deposition of freestanding graphene gyroids with controlled sub-60 nm unit cell sizes is demonstrated. Three-dimensional (3D) nickel templates were fabricated through electrodeposition into a selectively voided triblock terpolymer. The high temperature instability of sub-micron unit cell structures was effectively addressed through the early introduction of the car- bon precursor, which stabilizes the metallized gyroidal templates. The as-grown graphene gyroids are self-supporting and can be transferred onto a variety of substrates. Furthermore, they represent the smallest free standing periodic graphene 3D structures yet produced with a pore size of tens of nm, as analysed by electron microscopy and optical spectroscopy. We discuss generality of our methodology for the synthesis of other types of nanoscale, 3D graphene assemblies, and the trans- ferability of this approach to other 2D materials.

Halide perovskites passivated with potassium or rubidium show superior photovoltaic device performance compared to unpassivated samples. However, it is unclear which passivation route is more effective for film stability. Here, we directly compare the optoelectronic properties and stability of thin films when passivating triple-cation perovskite films with potassium or rubidium species. The optoelectronic and chemical studies reveal that the alloyed perovskites are tolerant toward higher loadings of potassium than rubidium. Whereas potassium complexes with bromide from the perovskite precursor solution to form thin surface passivation layers, rubidium additives favor the formation of phase-segregated micron-sized rubidium halide crystals. This tolerance to higher loadings of potassium allows us to achieve superior luminescent properties with potassium passivation. We also find that exposure to a humid atmosphere drives phase segregation and grain coalescence for all compositions, with the rubidium-passivated sample showing the highest sensitivity to nonperovskite phase formation. Our work highlights the benefits but also the limitations of these passivation approaches in maximizing both optoelectronic properties and the stability of perovskite films.

The local chemical composition of halide perovskites is a crucial factor in determining their macroscopic properties and their stability. While the combination of scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDX) is a powerful and widely used tool for accessing such information, electron-beam-induced damage and complex formulation of the films make this investigation challenging. Here we demonstrate how multivariate analysis, including statistical routines derived from “big data” research, such as principal component analysis (PCA), can be used to dramatically improve the signal recovery from fragile materials. We also show how a similar decomposition algorithm (non-negative matrix factorisation (NMF)) can unravel elemental composition at the nanoscale in perovskite films, highlighting the presence of segregated species and identifying the local stoichiometry at the nanoscale.

Multiple exciton generation (MEG) in semiconducting quantum dots is a process that produces multiple charge-carrier pairs from a single excitation. MEG is a possible route to bypass the Shockley-Queisser limit in single-junction solar cells but it remains challenging to harvest charge-carrier pairs generated by MEG in working photovoltaic devices. Initial yields of additional carrier pairs may be reduced due to ultrafast intraband relaxation processes that compete with MEG at early times. Quantum dots of materials that display reduced carrier cooling rates (e.g., PbTe) are therefore promising candidates to increase the impact of MEG in photovoltaic devices. Here we demonstrate PbTe quantum dot-based solar cells, which produce extractable charge carrier pairs with an external quantum efficiency above 120%, and we estimate an internal quantum efficiency exceeding 150%. Resolving the charge carrier kinetics on the ultrafast time scale with pump-probe transient absorption and pump-push-photocurrent measurements, we identify a delayed cooling effect above the threshold energy for MEG.

We have developed a versatile measurement system utilising field asymmetric ion mobility spectrometry (FAIMS) to study the photocatalytic degradation of VOCs at concentrations comparable to indoor air. FAIMS allows continuous monitoring of chemical species in the gas phase, whilst having a high separation selectivity and sensitivity, so can be used to identify multiple species concurrently at ppb concentrations, which are clear advantages over traditional characterization techniques used in photocatalytic air purification such as gas chromatography. Here we demonstrate the methodology with the photo-oxidation of 2-propanol, ethanol and acetone using a commercial titanium dioxide felt. To the best of our knowledge, this is the first time FAIMS has been used in photocatalytic air purification applications.

In this paper, an environmentally clean process to recycle the paste from a spent lead acid battery (LAB) is further developed in order to produce a porous carbon anode material for a lithium ion battery (LIB) which is currently under increasing focus as the solution for future energy storage and distribution networks. Using lead citrate from hydrometallurgical leaching of lead paste as a precursor, electrochemically active carbon materials were produced as a new product with hierarchical open sponge-like porosity. It was found that anode materials made from porous carbon by pyrolysing lead citrate at 500 °C, with high micropore (

Fully-printed electronics based on two-dimensional (2d) material heterostructures, such as field effect transistors, require robust and reproducible printed multi-layer stacks consisting of active channel, dielectric and conductive contact layers. Solution processing of graphite and other layered materials provides low-cost inks enabling printed electronic devices, for example by inkjet printing. However, the limited quality of the 2d material inks, the complexity of the layered arrangement for fully inkjet printed field effect heterostructures operating at room temperature and pressure, and the lack of a suitable dielectric 2d ink has impeded the fabrication of active field effect devices with fullyprinted 2d heterostructures. Moreover, electronic devices on textile (i.e. textile electronics) operate over a long time at room temperature, under strain and after several washing cycles. Exploiting the properties of inkjet printed electronics based on 2d materials for wearable and textile electronics requires robust, stable and washable printed devices. Here we demonstrate fully inkjet printed 2d material active heterostructures using graphene and hexagonal-boron nitride (h-BN) inks, and use them to fabricate all inkjet printed flexible and washable field effect transistors (FETs) on textile, reaching a field effect mobility of μ ~ 91 ± 29 cm2 V-1 s -1 on polyester fabric, at low operating voltages (< 5 V). The devices maintained their performance even under ∼ 4% strain and showed stable operation for periods up to 2 years, indicating the two-fold role of the h-BN layer as a flexible dielectric and encapsulant. Our graphene/h-BN FETs are washable up to 20 cycles, which is ideal for textile electronics. The viability of our process for printed and textile electronics is demonstrated by fully inkjet printing electronic circuits, such as reprogrammable volatile memory cells, complementary inverters, and OR logic gates with graphene/h-BN FETs., The authors are grateful for funding provided by the UK Engineering and Physical Sciences Research Council (EPSRC), T.C. acknowledges funding from the ERC grant Hetero2D. F.T. acknowledges funding from Trinity College, Cambridge and the Newton Trust. S.C., G.D. and C.D. acknowledge funding from ERC under grant number 259619 76 PHOTO EM and from the EU under grant number 77 312483 ESTEEM2. A.M. and R.S. acknowledge funding from the EU Graphene Flagship (grant No. 696656).

Cesium lead halide nanocrystals, CsPbX$_{3}$ (X = Cl, Br, I), exhibit photoluminescence quantum efficiencies approaching 100% without the core-shell structures usually used in conventional semiconductor nanocrystals. These high photoluminescence efficiencies make these crystals ideal candidates for light-emitting diodes (LEDs). However, because of the large surface area to volume ratio, halogen exchange between perovskite nanocrystals of different compositions occurs rapidly, which is one of the limiting factors for white-light applications requiring a mixture of different crystal compositions to achieve a broad emission spectrum. Here, we use mixtures of chloride and iodide CsPbX$_{3}$ (X = Cl, I) perovskite nanocrystals where anion exchange is significantly reduced. We investigate samples containing mixtures of perovskite nanocrystals with different compositions and study the resulting optical and electrical interactions. We report excitation transfer from CsPbCl$_{3}$ to CsPbI$_{3}$ in solution and within a poly(methyl methacrylate) matrix via photon reabsorption, which also occurs in electrically excited crystals in bulk heterojunction LEDs.

© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim Issues with the dissolution and diffusion of polysulfides in liquid organic electrolytes hinder the advance of lithium–sulfur batteries for next-generation energy storage. To trap and re-utilize the polysulfides without hampering lithium ion conductivity, a bio-inspired, brush-like interlayer consisting of zinc oxide (ZnO) nanowires and interconnected conductive frameworks is proposed. The chemical effect of ZnO on capturing polysulfides has been conceptually confirmed, initially by using a commercially available macroporous nickel foam as a conductive backbone, which is then replaced by a free-standing, ultra-light micro/mesoporous carbon (C) nanofiber mat for practical application. Having a high sulfur loading of 3 mg cm −2 , the sulfur/multi-walled carbon nanotube composite cathode with a ZnO/C interlayer exhibits a reversible capacity of 776 mA h g −1 after 200 cycles at 1C with only 0.05% average capacity loss per cycle. A good cycle performance at a high rate can be mainly attributed to the strong chemical bonding between ZnO and polysulfides, fast electron transfer, and an optimized ion diffusion path arising from a well-organized nanoarchitecture. These results herald a new approach to advanced lithium–sulfur batteries using brush-like chemi-functional interlayers.

The solid electrolyte interphase (SEI) of the high capacity anode material Si is monitored over multiple electrochemical cycles by (7)Li, (19)F, and (13)C solid-state nuclear magnetic resonance spectroscopies, with the organics dominating the SEI. Homonuclear correlation experiments are used to identify the organic fragments -OCH2CH2O-, -OCH2CH2-, -OCH2CH3, and -CH2CH3 contained in both oligomeric species and lithium semicarbonates ROCO2Li, RCO2Li. The SEI growth is correlated with increasing electrode tortuosity by using focused ion beam and scanning electron microscopy. A two-stage model for lithiation capacity loss is developed: initially, the lithiation capacity steadily decreases, Li(+) is irreversibly consumed at a steady rate, and pronounced SEI growth is seen. Later, below 50% of the initial lithiation capacity, less Si is (de)lithiated resulting in less volume expansion and contraction; the rate of Li(+) being irreversibly consumed declines, and the Si SEI thickness stabilizes. The decreasing lithiation capacity is primarily attributed to kinetics, the increased electrode tortuousity severely limiting Li(+) ion diffusion through the bulk of the electrode. The resulting changes in the lithiation processes seen in the electrochemical capacity curves are ascribed to non-uniform lithiation, the reaction commencing near the separator/on the surface of the particles.

Here we report on the heat-induced solid-state replacement of GaAs by Au in nanowires. Such replacement of semiconductor nanowires by metals is envisioned as a method to achieve well-defined junctions within nanowires. To better understand the mechanisms and dynamics that govern the replacement reaction, we performed in situ heating studies using high-resolution scanning transmission electron microscopy. The dynamic evolution of the phase boundary was investigated, as well as the crystal structure and orientation of the different phases at reaction temperatures. In general, the replacement proceeds one GaAs(111) bilayer at a time, and no fixed epitaxial relation could be found between the two phases. The relative orientation of the phases affects the replacement dynamics and can induce growth twins in the Au nanowire phase. In the case of a limited Au supply, the metal phase can also become liquid.

The preparation of highly efficient perovskite nanocrystal light-emitting diodes is shown. A new trimethylaluminum vapor-based crosslinking method to render the nanocrystal films insoluble is applied. The resulting near-complete nanocrystal film coverage, coupled with the natural confinement of injected charges within the perovskite crystals, facilitates electron-hole capture and give rise to a remarkable electroluminescence yield of 5.7%. Funding Agencies|EPSRC [EP/M005143/1, EP/J017361/1, EP/G037221/1]; Gates Cambridge Trust; CNPq [246050/2012-8]; ERC [259619 PHOTO-EM]; EU [312483 ESTEEM2]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University [200900971]; Cambridge Commonwealth European and International Trust; Cambridge Australian Scholarships

The lack of thermal stability of perovskite solar cells is hindering the progress of this technology towards adoption in the consumer market. Different pathways of thermal degradation are activated at different temperatures in these complex nanostructured hybrid composites. Thus, it is essential to explore the thermal response of the mesosuperstructured composite device to engineer materials and operating protocols. Here we produce devices according to four well-established recipes, and characterize their photovoltaic performance as they are heated within the operational range. The devices are analysed using transmission electron microscopy as they are further heated in situ, to monitor changes in morphology and chemical composition. We identify mechanisms for structural and chemical changes, such as iodine and lead migration, which appear to be correlated to the synthesis conditions. In particular, we identify a correlation between exposure of the perovskite layer to air during processing and elemental diffusion during thermal treatment. Solar cells based on lead halide perovskite composites have become increasingly popular in the past few years owing to a combination of low synthesis cost and high power conversion efficiency, with certified values in excess of 20% (refs 1,2,3,4,5). However, the stability of such devices is a concern—it is well known that heating at or above around 85 ∘C, a temperature close to those reached during normal operation in full sunlight, performance degrades rapidly, and such instability is exacerbated by exposure to moisture; systematic thermal and ageing studies are required to understand such degradation processes. Changes happen in both the organic and inorganic components of the cells; the resilience of the perovskite layer, in particular, is expected to become a limiting factor once different hole-conducting materials (or hole-conductor-free cells) are developed. To overcome this limitation, it is vital to understand the degradation pathways of the structures involved, which here are observed at nanometre-scale spatial resolution in situ, inside an analytical scanning transmission electron microscope (STEM), while the composition is monitored with elemental mapping through energy-dispersive X-ray analysis (EDX). The analysis of such devices is challenging owing to several factors. The spatial dimensions relevant to the fabrication and the operation of the cells are in the 1–100 nm range, and the materials are easily damaged by exposure to an electron beam in a TEM, requiring careful tuning of the electron dose. The system also includes organic and inorganic components in an assembly with complex chemistry and morphology. Finally, the rapid changes to the devices in air and the low degradation temperatures pose an additional challenge to the experiment, which needs to be timed appropriately and carefully executed. The monitoring of this process is made possible by combining several recent advances in TEM technology. The use of high-brightness electron guns and detectors with large collection areas allows the fast acquisition of high-quality EDX maps with limited electron dose on the sample; the signal-to-noise ratio of the maps can be further increased by applying denoising algorithms (PCA, principal components analysis) within an open-source software suite. The development of novel in situ heating holders for TEM, based on micro-heaters and featuring high stability and fast response, was also crucial—in particular, the holder used here allows very precise control (sub-degree) at values just above room temperature, as well as providing fast heating and cooling (a few seconds for the temperatures in use in this paper). The good spatial stability of the holder is crucial in acquiring EDX maps.

Electron tomography is an invaluable method for 3D cellular imaging. The technique is, however, limited by the specimen geometry, with a loss of resolution due to a restricted tilt range, an increase in specimen thickness with tilt, and a resultant need for subjective and time-consuming manual segmentation. Here we show that 3D reconstructions of needle-shaped biological samples exhibit isotropic resolution, facilitating improved automated segmentation and feature detection. By using scanning transmission electron tomography, with small probe convergence angles, high spatial resolution is maintained over large depths of field and across the tilt range. Moreover, the application of compressed sensing methods to the needle data demonstrates how high fidelity reconstructions may be achieved with far fewer images (and thus greatly reduced dose) than needed by conventional methods. These findings open the door to high fidelity electron tomography over critically relevant length-scales, filling an important gap between existing 3D cellular imaging techniques.

Organometal halide (hybrid) perovskite solar cells have been fabricated following four different deposition procedures and investigated in order to find correlations between the solar cell characteristics/performance and their structure and composition as determined by combining depth-resolved imaging with time-of-flight secondary ion mass spectrometry (ToF-SIMS), X-ray photoelectron spectroscopy (XPS), and analytical scanning transmission electron microscopy (STEM). The interface quality is found to be strongly affected by the perovskite deposition procedure, and in particular from the environment where the conversion of the starting precursors into the final perovskite is performed (air, nitrogen, or vacuum). The conversion efficiency of the precursors into the hybrid perovskite layer is compared between the different solar cells by looking at the ToF-SIMS intensities of the characteristic molecular fragments from the perovskite and the precursor materials. Energy dispersive X-ray spectroscopy in the STEM confirms the macroscopic ToF-SIMS findings and allows elemental mapping with nanometer resolution. Clear evidence for iodine diffusion has been observed and related to the fabrication procedure.

The chemical composition of core-shell nanoparticle clusters have been determined through principal component analysis (PCA) and independent component analysis (ICA) of an energy-dispersive X-ray (EDX) spectrum image (SI) acquired in a scanning transmission electron microscope (STEM). The method blindly decomposes the SI into three components, which are found to accurately represent the isolated and unmixed X-ray signals originating from the supporting carbon film, the shell, and the bimetallic core. The composition of the latter is verified by and is in excellent agreement with the separate quantification of bare bimetallic seed nanoparticles.

Arrays of hyperbranched mesostructures self-assembled from the gas phase display a decreased overpotential for the water oxidation reaction.

Hybrid glasses connect emerging fields of metal-organic frameworks (MOFs) with the glass-formation, amorphization, and melting processes of these structurally diverse and chemically versatile systems. Most zeolites, including MOFs, amorphize around the glass transition, devitrifying and then melting at much higher temperatures. The relationship between the two processes has so far not been investigated. Herein we show how heating first results in a low density perfect glass, following an order-order transition, leading to a super-strong liquid of low fragility that dynamically controls MOF collapse. A subsequent order-disorder transition creates a high density liquid of greater fragility. After crystallization and melting, subsequent cooling results in a stable glass virtually identical to the high density phase. Furthermore, the wide-ranging melting temperatures of different MOFs suggest these can be differentiated by topology. Our research provides new insight into the stability and functionality of these novel ductile crystalline materials, including the possibility of melt-casting MOFs., Comment: 15 pages, 4 figures

A novel ultra-lightweight three-dimensional (3-D) cathode system for lithium sulphur (Li–S) batteries has been synthesised by loading sulphur on to an interconnected 3-D network of few-layered graphene (FLG) via a sulphur solution infiltration method. A free-standing FLG monolithic network foam was formed as a negative of a Ni metallic foam template by CVD followed by etching away of Ni. The FLG foam offers excellent electrical conductivity, an appropriate hierarchical pore structure for containing the electro-active sulphur and facilitates rapid electron/ion transport. This cathode system does not require any additional binding agents, conductive additives or a separate metallic current collector thus decreasing the weight of the cathode by typically � 20–30 wt%. A Li–S battery with the sulphur–FLG foam cathode shows good electrochemical stability and high rate discharge capacity retention for up to 400 discharge/charge cycles at a high current density of 3200 mA g � 1 . Even after 400 cycles the capacity decay is only � 0.064% per cycle relative to the early (e.g. the 5th cycle) discharge capacity, while yielding an average columbic efficiency of � 96.2%. Our results indicate the potential suitability of graphene foam for efficient, ultra-light and high-performance batteries.

Nano-structured silicon anodes are attractive alternatives to graphitic carbons in rechargeable Li-ion batteries, owing to their extremely high capacities. Despite their advantages, numerous issues remain to be addressed, the most basic being to understand the complex kinetics and thermodynamics that control the reactions and structural rearrangements. Elucidating this necessitates real-time in situ metrologies, which are highly challenging, if the whole electrode structure is studied at an atomistic level for multiple cycles under realistic cycling conditions. Here we report that Si nanowires grown on a conducting carbon-fibre support provide a robust model battery system that can be studied by (7)Li in situ NMR spectroscopy. The method allows the (de)alloying reactions of the amorphous silicides to be followed in the 2nd cycle and beyond. In combination with density-functional theory calculations, the results provide insight into the amorphous and amorphous-to-crystalline lithium-silicide transformations, particularly those at low voltages, which are highly relevant to practical cycling strategies.

The mechanisms and kinetics of axial Ge-Si nanowire heteroepitaxial growth based on the tailoring of the Au catalyst composition via Ga alloying are studied by environmental transmission electron microscopy combined with systematic ex situ CVD calibrations. The morphology of the Ge-Si heterojunction, in particular, the extent of a local, asymmetric increase in nanowire diameter, is found to depend on the Ga composition of the catalyst, on the TMGa precursor exposure temperature, and on the presence of dopants. To rationalize the findings, a general nucleation-based model for nanowire heteroepitaxy is established which is anticipated to be relevant to a wide range of material systems and device-enabling heterostructures.

Tantalum-oxide thin films are shown to catalyse single- and multi-walled carbon nanotube growth by chemical vapour deposition. A low film thickness, the nature of the support material (best results with SiO2) and an atmospheric process gas pressure are of key importance for successful nanotube nucleation. Strong material interactions, such as silicide formation, inhibit nanotube growth. In situ X-ray photoelectron spectroscopy indicates that no catalyst reduction to Ta-metal or Ta-carbide occurs during our nanotube growth conditions and that the catalytically active phase is the Ta-oxide phase. Such a reduction-free oxide catalyst can be technologically advantageous.

We observe the formation of metastable AuGe phases without quenching, during strictly isothermal nucleation and growth of Ge nanowires, using video-rate lattice-resolved environmental transmission electron microscopy. We explain the unexpected formation of these phases through a novel pathway involving changes in composition rather than temperature. The metastable catalyst has important implications for nanowire growth, and more broadly, the isothermal process provides both a new approach to growing and studying metastable phases, and a new perspective on their formation. © 2012 American Physical Society.

A systematic study on the parameter space of graphene CVD on polycrystalline Cu foils is presented, aiming at a more fundamental process rationale in particular regarding the choice of carbon precursor and mitigation of Cu sublimation. CH4 as precursor requires H2 dilution and temperatures ≥1000°C to keep the Cu surface reduced and yield a high quality, complete monolayer graphene coverage. The H2 atmosphere etches as-grown graphene, hence maintaining a balanced CH4/H2 ratio is critical. Such balance is more easily achieved at low pressure conditions, at which however Cu sublimation reaches deleterious levels. In contrast, C6H6 as precursor requires no reactive diluent and consistently gives similar graphene quality at 100-150°C lower temperatures. The lower process temperature and more robust processing conditions allow the problem of Cu sublimation to be effectively addressed. Graphene formation is not inherently self-limited to a monolayer for any of the precursors. Rather, the higher the supplied carbon chemical potential the higher the likelihood of film inhomogeneity and primary and secondary multilayer graphene nucleation. For the latter, domain boundaries of the inherently polycrystalline CVD graphene offer pathways for a continued carbon supply to the catalyst. Graphene formation is significantly affected by the Cu crystallography, i.e. the evolution of microstructure and texture of the catalyst template form an integral part of the CVD process.

We study the Fe-catalyzed chemical vapor deposition of carbon nanotubes by complementary in situ grazing-incidence X-ray diffraction, in situ X-ray reflectivity, and environmental transmission electron microscopy. We find that typical oxide supported Fe catalyst films form widely varying mixtures of bcc and fcc phased Fe nanoparticles upon reduction, which we ascribe to variations in minor commonly present carbon contamination levels. Depending on the as-formed phase composition, different growth modes occur upon hydrocarbon exposure: For γ-rich Fe nanoparticle distributions, metallic Fe is the active catalyst phase, implying that carbide formation is not a prerequisite for nanotube growth. For α-rich catalyst mixtures, Fe3C formation more readily occurs and constitutes part of the nanotube growth process. We propose that this behavior can be rationalized in terms of kinetically accessible pathways, which we discuss in the context of the bulk iron–carbon phase diagram with the inclusion of phase equilibrium lines for metastable Fe3C. Our results indicate that kinetic effects dominate the complex catalyst phase evolution during realistic CNT growth recipes.

Radiative recombination in thin films of the archetypical, high‐performing perovskites CH3NH3PbBr3 and CH3NH3PbI3 shows localized regions of increased emission with dimensions ≈500 nm. Maps of the spectral emission line shape show narrower emission lines in high emission regions, which can be attributed to increased order. Excited states do not diffuse out of high emission regions before they decay, but are decoupled from nearby regions, either by slow diffusion rates or energetic barriers.

Operational stability is the main issue hindering the commercialisation of perovskite solar cells. Here, a long term light soaking test was performed on large area hybrid halide perovskite solar cells to investigate the morphological and chemical changes associated with the degradation of photovoltaic performance occurring within the devices. Using Scanning Transmission Electron Microscopy (STEM) in conjunction with EDX analysis on device cross sections, we observe the formation of gold clusters in the perovskite active layer as well as in the TiO2 mesoporous layer, and a severe degradation of the perovskite due to iodine migration into the hole transporter. All these phenomena are associated with a drastic drop of all the photovoltaic parameters. The use of advanced electron microscopy techniques and data processing provides new insights on the degradation pathways, directly correlating the nanoscale structure and chemistry to the macroscopic properties of hybrid perovskite devices.

Bulk-heterojunction (BHJ) non-fullerene organic solar cells prepared from sequentially deposited donor and acceptor layers (sq-BHJ) have recently been promising to be highly efficient, environmentally friendly, and compatible with large area and roll-to-roll fabrication. However, the related photophysics at donor-acceptor interface and the vertical heterogeneity of donor-acceptor distribution, critical for exciton dissociation and device performance, are largely unexplored. Herein, steady-state and time-resolved optical and electrical techniques are employed to characterize the interfacial trap states. Correlating with the luminescent efficiency of interfacial states and its non-radiative recombination, interfacial trap states are characterized to be about 50% more populated in the sq-BHJ devices than the as-cast BHJ (c-BHJ), which probably limits the device voltage output. Cross-sectional energy-dispersive X-ray spectroscopy and ultraviolet photoemission spectroscopy depth profiling directly visualize the donor-acceptor vertical stratification with a precision of 1-2 nm. From the proposed “needle” model, the high exciton dissociation efficiency is rationalized. Our study highlights the promise of sequential deposition to fabricate efficient solar cells, and points towards improving the voltage output and overall device performance via eliminating interfacial trap states.